Search NASA⌕ Search

SEARCH · Search NASA

Results for “structural dynamics testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41

Reduced gravity multibody dynamics testing

The Final Report on reduced gravity multibody dynamics testing is presented. Tests were conducted on board the NASA KC-135 RGA in Houston, Texas. The objective was to analyze the effects of large angle rotations on flexible, multi-segmented structures. The flight experiment was conducted to provide data which will be compared to the data gathered from ground tests of the same configurations. The flight and ground tested data will be used to validate the TREETOPS software, software which models dynamic multibody systems, and other multibody codes. The flight experiment consisted of seven complete flights on board the KC-135 RGA during two one-week periods. The first period of testing was 4-9 Apr. 1993. The second period of testing was 13-18 Jun. 1993.

Sillanpaa, Meija↗

Mid-frequency Band Dynamics of Large Space Structures

High and low intensity dynamic environments experienced by a spacecraft during launch and on-orbit operations, respectively, induce structural loads and motions, which are difficult to reliably predict. Structural dynamics in low- and mid-frequency bands are sensitive to component interface uncertainty and non-linearity as evidenced in laboratory testing and flight operations. Analytical tools for prediction of linear system response are not necessarily adequate for reliable prediction of mid-frequency band dynamics and analysis of measured laboratory and flight data. A new MATLAB toolbox, designed to address the key challenges of mid-frequency band dynamics, is introduced in this paper. Finite-element models of major subassemblies are defined following rational frequency-wavelength guidelines. For computational efficiency, these subassemblies are described as linear, component mode models. The complete structural system model is composed of component mode subassemblies and linear or non-linear joint descriptions. Computation and display of structural dynamic responses are accomplished employing well-established, stable numerical methods, modern signal processing procedures and descriptive graphical tools. Parametric sensitivity and Monte-Carlo based system identification tools are used to reconcile models with experimental data and investigate the effects of uncertainties. Models and dynamic responses are exported for employment in applications, such as detailed structural integrity and mechanical-optical-control performance analyses.

dynamics↗

Fluid-Structure Interaction Simulations of the ASPIRE SR03 Supersonic Parachute Flight Test

Research into parachute performance continues to be a source of significant investment from the National Aeronautics and Space Administration to mitigate risks and to enable a variety of exploration missions, including landing on Mars as well as returning to Earth. The cost of flight tests to certify any changes to the current state-of-the-art parachute designs limits the development of next generation parachute systems. Fluid-structure interaction simulations could help accelerate this process once validated. The Launch, Ascent, and Vehicle Aerodynamics team is developing the capability to perform such fluid-structure interaction simulations by coupling a higher-order Cartesian immersed boundary computational fluid dynamics solver with adaptive mesh refinement to a finite element structural dynamics solver in space and time. We continue the effort to validate this tool with the Advanced Supersonic Parachute Inflation Research Experiments SR03 flight test featuring a strengthened parachute akin to the Mars 2020 mission that landed the Perseverance rover on Mars, and a higher freestream dynamic pressure prior to inflation. The effect of the flow conditions’ angle of attack and of the initial parachute shape are quantified. The impact of relaxing modeling assumptions with regards to radial stiffeners on the parachute canopy is also investigated. Results demonstrate improvements in agreement with the pull force recorded during the SR03 flight test as the initial conditions of the flow and parachute are brought closer to those experienced in flight, and further improved when the radial stiffener modeling assumptions are relaxed.

ESM↗

Fluid-Structure Interaction Simulations of the ASPIRE SR03 Supersonic Parachute Flight Test

Research into parachute performance continues to be a source of significant investment from the National Aeronautics and Space Administration to mitigate risks and to enable a variety of exploration missions, including landing on Mars as well as returning to Earth. The cost of flight tests to certify any changes to the current state-of-the-art parachute designs limits the development of next generation parachute systems. Fluid-structure interaction simulations could help accelerate this process once validated. The Launch, Ascent, and Vehicle Aerodynamics team is developing the capability to perform such fluid-structure interaction simulations by coupling a higher-order Cartesian immersed boundary computational fluid dynamics solver with adaptive mesh refinement to a finite element structural dynamics solver in space and time. We continue the effort to validate this tool with the Advanced Supersonic Parachute Inflation Research Experiments SR03 flight test featuring a strengthened parachute akin to the Mars 2020 mission that landed the Perseverance rover on Mars, and a higher freestream dynamic pressure prior to inflation. The effect of the flow conditions’ angle of attack and of the initial parachute shape are quantified. The impact of relaxing modeling assumptions with regards to radial stiffeners on the parachute canopy is also investigated. Results demonstrate improvements in agreement with the pull force recorded during the SR03 flight test as the initial conditions of the flow and parachute are brought closer to those experienced in flight, and further improved when the radial stiffener modeling assumptions are relaxed.

ESM↗

Application of polyimide actuator rod seals

Development of polyimide two-stage hydraulic actuator rod seals for application in high-performance aircraft was accomplished. The significant portion of the effort was concentrated on optimization of the chevron and K-section second-stage seal geometries to satisfy the requirements for operation at 450 K (350 F) with dynamic pressure loads varying between 200 psig steady-state and 1500 psig impulse cycling. Particular significance was placed on reducing seal gland dimension by efficiently utilizing the fatigue allowables of polyimide materials. Other objectives included investigation of pressure balancing techniques for first-stage polyimide rod seals for 4000 psig 450 K(350 F) environment and fabrication of a modular retainer for the two-stage combination. Seals were fabricated in 0.0254 m (1.0in.) and 0.0635 m (2.5in.) sizes and tested for structural integrity, frictional resistance, and endurance life. Test results showed that carefully designed second stages using polyimides could be made to satisfy the dynamic return pressure requirements of applications in high-performance aircraft. High wear under full system pressure indicated that further research is necessary to obtain an acceptable first-stage design. The modular retainer was successfully tested and showed potential for new actuator applications.

Watermann, A. W.↗

Survey of NASA research on crash dynamics

Ten years of structural crash dynamics research activities conducted on general aviation aircraft by the National Aeronautics and Space Administration (NASA) are described. Thirty-two full-scale crash tests were performed at Langley Research Center, and pertinent data on airframe and seat behavior were obtained. Concurrent with the experimental program, analytical methods were developed to help predict structural behavior during impact. The effects of flight parameters at impact on cabin deceleration pulses at the seat/occupant interface, experimental and analytical correlation of data on load-limiting subfloor and seat configurations, airplane section test results for computer modeling validation, and data from emergency-locator-transmitter (ELT) investigations to determine probable cause of false alarms and nonactivations are assessed. Computer programs which provide designers with analytical methods for predicting accelerations, velocities, and displacements of collapsing structures are also discussed.

Thomson, R. G.↗

Technical challenges of integrating the Space Shuttle

A review is presented of the technology involved in integrating the Space Shuttle system. A powered flight analysis of the Shuttle is presented, touching upon the following areas: ascent profile and abort mode integration, sizing and design, control of load factor by a stage thrust shaping, structural load constraints, flight performance reserve and trajectory design for the orbital flight test. A discussion is presented of aerothermodynamics including aerodynamic and plume heating. Flight control and separation is considered with attention paid to liftoff, ascent to booster staging, elevon load relief, booster tailoff thrust mismatch and gimbal limitations and booster separation. Structural analysis and dynamics is examined, considering: vehicle loads and modes and the pogo effect. Propulsion aspects (hydraulics, the LH2 recirculation system, the antigeyser system, the pressurization system, etc.), ground vibration tests, separation system verification and flight readiness firing are all described.

Martin, A. C.↗

Water Impact Test and Simulation of a Composite Energy Absorbing Fuselage Section

In March 2002, a 25-ft/s vertical drop test of a composite fuselage section was conducted onto water. The purpose of the test was to obtain experimental data characterizing the structural response of the fuselage section during water impact for comparison with two previous drop tests that were performed onto a rigid surface and soft soil. For the drop test, the fuselage section was configured with ten 100-lb. lead masses, five per side, that were attached to seat rails mounted to the floor. The fuselage section was raised to a height of 10-ft. and dropped vertically into a 15-ft. diameter pool filled to a depth of 3.5-ft. with water. Approximately 70 channels of data were collected during the drop test at a 10-kHz sampling rate. The test data were used to validate crash simulations of the water impact that were developed using the nonlinear, explicit transient dynamic codes, MSC.Dytran and LS-DYNA. The fuselage structure was modeled using shell and solid elements with a Lagrangian mesh, and the water was modeled with both Eulerian and Lagrangian techniques. The fluid-structure interactions were executed using the fast general coupling in MSC.Dytran and the Arbitrary Lagrange-Euler (ALE) coupling in LS-DYNA. Additionally, the smooth particle hydrodynamics (SPH) meshless Lagrangian technique was used in LS-DYNA to represent the fluid. The simulation results were correlated with the test data to validate the modeling approach. Additional simulation studies were performed to determine how changes in mesh density, mesh uniformity, fluid viscosity, and failure strain influence the test-analysis correlation.

Fasanella, Edwin L.↗

Modeling and Analysis of Structural Dynamics for a One-Tenth Scale Model NGST Sunshield

New modeling and analysis techniques have been developed for predicting the dynamic behavior of the Next Generation Space Telescope (NGST) sunshield. The sunshield consists of multiple layers of pretensioned, thin-film membranes supported by deployable booms. Modeling the structural dynamic behavior of the sunshield is a challenging aspect of the problem due to the effects of membrane wrinkling. A finite element model of the sunshield was developed using an approximate engineering approach, the cable network method, to account for membrane wrinkling effects. Ground testing of a one-tenth scale model of the NGST sunshield were carried out to provide data for validating the analytical model. A series of analyses were performed to predict the behavior of the sunshield under the ground test conditions. Modal analyses were performed to predict the frequencies and mode shapes of the test article and transient response analyses were completed to simulate impulse excitation tests. Comparison was made between analytical predictions and test measurements for the dynamic behavior of the sunshield. In general, the results show good agreement with the analytical model correctly predicting the approximate frequency and mode shapes for the significant structural modes.

Johnston, John↗

Generalized Predictive Control for Active Stability Augmentation and Vibration Reduction on an Aeroelastic Tiltrotor Model

Tiltrotor aircraft are defining the state-of-the-art in vertical lift technology as they have the potential to greatly expand rotary-wing operational boundaries. However, they are often limited in forward flight speed due to complex coupled rotor and wing dynamic instabilities. The U.S. Army and NASA have been developing a new wind tunnel model, the TiltRotor Aeroelastic Stability Testbed(TRAST), to test proprotors in the NASA Langley Research Center Transonic Dynamics Tunnel (TDT) to investigate aeroelastic stability in cruise. The test is intended to provide high-quality research data for analytical tool development and validation. In addition, the TRAST model will support, develop, and mature new technologies for the design of advanced proprotor aircraft. Stability augmentation and vibration reduction during testing is planned with the use of an active control methodology known as Generalized Predictive Control(GPC). GPC is an autoregressive control law that experimentally acquires a system identification to derive the input-output relation of controls and corresponding sensors. This type of control law is especially useful for complex dynamic interactions that are difficult to explicitly model such as proprotor pylon instability, often referred to as whirl flutter. GPC has been successfully employed on other tiltrotor vehicles to suppress whirl flutter instabilities and vibrations. To aid in the characterization of the wind-tunnel model and in tool development, an analytical representation of the wind-tunnel model was developed using the rotorcraft comprehensive analysis system (RCAS) that simulates structural dynamics and aerodynamics. RCAS was used to derive state-space estimates of the physical plant at various flight conditions to test control law effectiveness. This paper will present an overview of the test article development, a description of RCAS, an explanation of the GPC methodology, and results of GPC being applied to state-space plant estimates of the TRAST model. In these simulations, GPC was effective at stabilizing the aircraft beyond the whirl-flutter boundary while simultaneously reducing vibrations across the flight regime. Additionally, a modern advancement to GPC, termed advanced GPC (AGPC), is introduced that enables a self-adapting system identification. Preliminary results show that AGPC is successful at self-correction as the plant changes from what was used for system identification.

tiltrotor↗

The DELTA MONSTER: An RPV designed to investigate the aerodynamics of a delta wing platform

The mission requirements for the performance of aerodynamic tests on a delta wind planform posed some problems, these include aerodynamic interference; structural support; data acquisition and transmission instrumentation; aircraft stability and control; and propulsion implementation. To eliminate the problems of wall interference, free stream turbulence, and the difficulty of achieving dynamic similarity between the test and actual flight aircraft that are associated with aerodynamic testing in wind tunnels, the concept of the remotely piloted vehicle which can perform a basic aerodynamic study on a delta wing was the main objective for the Green Mission - the Delta Monster. The basic aerodynamic studies were performed on a delta wing with a sweep angle greater than 45 degrees. These tests were performed at various angles of attack and Reynolds numbers. The delta wing was instrumented to determine the primary leading edge vortex formation and location, using pressure measurements and/or flow visualization. A data acquisition system was provided to collect all necessary data.

Connolly, Kristen↗

Functional and dynamics testing of the flexible solar array for the communications technology satellite

The test objectives, test methods, thermal environmental simulations, and test results are described, for a series of combined dynamic, thermal, and vacuum environmental tests on a Deployable Solar Array for the Communications Technology Satellite. Six major resonant structural modes were observed over an excitation range of 0.1-1.0 Hz. Corresponding modal damping factors were found to be between 0.001 and 0.01. Variation of temperature environments between -125 C and 42 C did not significantly affect the characteristics of the fundamental modes, but did influence some of the higher modes. Superharmonic response behavior was observed. The tests also verified functional mechanical performance of the solar array under thermal and vacuum conditions.

Harrison, T. D.↗

Radial SI latches vibration test data review

Dynamic testing of the Space Telescope Scientific Instrument Radial Latches was performed as specified by the designated test criteria. No structural failures were observed during the test. The alignment stability of the instrument simulator was within required tolerances after testing. Particulates were discovered around the latch bases, after testing, due to wearing at the B and C latch interface surfaces. This report covers criteria derivation, testing, and test results.

Harrison, P. M.↗

Model correlation and damage location for large space truss structures: Secant method development and evaluation

On-orbit testing of a large space structure will be required to complete the certification of any mathematical model for the structure dynamic response. The process of establishing a mathematical model that matches measured structure response is referred to as model correlation. Most model correlation approaches have an identification technique to determine structural characteristics from the measurements of the structure response. This problem is approached with one particular class of identification techniques - matrix adjustment methods - which use measured data to produce an optimal update of the structure property matrix, often the stiffness matrix. New methods were developed for identification to handle problems of the size and complexity expected for large space structures. Further development and refinement of these secant-method identification algorithms were undertaken. Also, evaluation of these techniques is an approach for model correlation and damage location was initiated.

Smith, Suzanne Weaver↗

U.S. perspective on technology demonstration experiments for adaptive structures

Evaluation of design concepts for adaptive structures is being performed in support of several focused research programs. These include programs such as Precision Segmented Reflector (PSR), Control Structure Interaction (CSI), and the Advanced Space Structures Technology Research Experiment (ASTREX). Although not specifically designed for adaptive structure technology validation, relevant experiments can be performed using the Passive and Active Control of Space Structures (PACOSS) testbed, the Space Integrated Controls Experiment (SPICE), the CSI Evolutionary Model (CEM), and the Dynamic Scale Model Test (DSMT) Hybrid Scale. In addition to the ground test experiments, several space flight experiments have been planned, including a reduced gravity experiment aboard the KC-135 aircraft, shuttle middeck experiments, and the Inexpensive Flight Experiment (INFLEX).

Aswani, Mohan↗

Structural Tailoring/Analysis for Hypersonic Components - A computational simulation

The development of STAHYC (Structural Tailoring/Analysis for Hypersonic Components), a numerical tool for the optimum design of an engine inlet wall panel for hypersonic aerospace vehicles, is described. STAHYC integrates FORTRAN modules of different disciplines, including fluid dynamics, heat transfer, structural analysis, and optimization. The discussion covers the system design concept, system components, system automation, system testing, established links, and data transfer between different computational modules. The various algorithms used in STAHYC are also discussed.

Narayanan, G. V.↗

Magnetic Excitation for Spin Vibration Testing

The Dynamic Spin Rig Laboratory (DSRL) at the NASA Lewis Research Center is a facility used for vibration testing of structures under spinning conditions. The current actuators used for excitation are electromagnetic shakers which are configured to apply torque to the rig's vertical rotor. The rotor is supported radially and axially by conventional bearings. Current operation is limited in rotational speed, excitation capability, and test duration. In an effort to enhance its capabilities, the rig has been initially equipped with a radial magnetic bearing which provides complementary excitation and shaft support. The new magnetic feature has been used in actual blade vibration tests and its performance has been favorable. Due to the success of this initial modification further enhancements are planned which include making the system fully magnetically supported. This paper reports on this comprehensive effort to upgrade the DSRL with an emphasis on the new magnetic excitation capability.

Johnson, Dexter↗

Accelerated Testing Methodology Developed for Determining the Slow Crack Growth of Advanced Ceramics

Constant stress-rate ("dynamic fatigue") testing has been used for several decades to characterize the slow crack growth behavior of glass and structural ceramics at both ambient and elevated temperatures. The advantage of such testing over other methods lies in its simplicity: strengths are measured in a routine manner at four or more stress rates by applying a constant displacement or loading rate. The slow crack growth parameters required for component design can be estimated from a relationship between strength and stress rate. With the proper use of preloading in constant stress-rate testing, test time can be reduced appreciably. If a preload corresponding to 50 percent of the strength is applied to the specimen prior to testing, 50 percent of the test time can be saved as long as the applied preload does not change the strength. In fact, it has been a common, empirical practice in the strength testing of ceramics or optical fibers to apply some preloading (<40 percent). The purpose of this work at the NASA Lewis Research Center is to study the effect of preloading on measured strength in order to add a theoretical foundation to the empirical practice.

Choi, Sung R.↗