Search NASA⌕ Search

SEARCH · Search NASA

Results for “AFM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42

A chemical/mineralogical investigation of the behavior of sulfoaluminate binders submitted to accelerated carbonation

The paper addresses the carbonation of CSA based binders from the mechanical, chemical and mineralogical point of view. Three different binders have been investigated, revealing that many hydrated phases can protect ettringite against carbonation. In particular, the presence of AFm phases gives a significant contribution to buffer the pH in alkaline range and to preserve the protective film of steel reinforcement bars. In a carbonated environment AFm phases act as ionic exchangers: carbonate ions replace sulfates in the interlayer and in these conditions the released sulfate ions contribute to the formation of new ettringite, with a beneficial effect on compressive strength performances. Experimental data are compared with models and carbonation mechanisms are described.

36 MATERIALS SCIENCE↗

Effect of chloride ingress on self-healing recovery of smart cementitious composite incorporating crystalline admixture and MgO expansive agent

Highlights: • Crack closure under wet/dry cycles in chloride solution is higher than the one in distilled water. • Element analysis shows that calcium is vital for crack healing either in water or chloride solution. • AFm is consumed by chloride ion to form Fs, and Fs were decomposed to AH{sub 3} by carbonation. • Soluble reactive silica reacts with calcium hydrate to form C-S-H gel to heal concrete cracks. • Expansion of magnesium hydroxide facilitates crack self-healing by interconnected network. In this study, the effect of chloride environment containing various concentrations of chloride ion (Cl{sup −}) on self-healing performance of pre-cracked cementitious composite containing crystalline admixture (CA) and MgO expansive agent (MEA) was investigated under wet-dry cycles in chloride solutions. The results revealed that the Cl{sup −} changed the mineralogy of self-healing products, and consequently, affected the crack closure ratio and mechanical strength recovery. When self-healing occurred in distilled water, a large amount of ettringite (AFt) were detected, whereas in Cl{sup −} solution, monosulfate (AFm) was consumed by Cl{sup −} to form Friedel's salt (Fs), and then the Fs was decomposed to Al(OH){sub 3}(AH{sub 3}) due to carbonation. During the multiphase conversion process, hydroxide (OH{sup −}) was released into crack solution, therefore the dissolved carbon dioxide (CO{sub 2}) concentration was increased. The carbonation of the crystals formed in cracks was accelerated with the volume expansion, which achieved rapid crack sealing but contributed little to the mechanical performance recovery.

36 MATERIALS SCIENCE↗

Autogenous formation and smart behaviors of nitrite- and nitrate-intercalated layered double hydroxides (LDHs) in Portland cement-metakaolin-dolomite blends

In this work, the influence of sodium nitrite (NaNO{sub 2}) and sodium nitrate (NaNO{sub 3}) corrosion inhibitors on the composition, structure, and chloride binding behaviors of layered double hydroxides (LDHs) formed in ternary ordinary Portland cement-metakaolin-dolomite (OPC-MK-DM) systems is studied. The results show that the nitrite and nitrate anions are preferably intercalated in the CaAl LDHs (AFm phases), but not in the MgAl LDHs (hydrotalcite-type phases) due to its limited formation in these ternary cementitious systems cured at ambient temperature. The autogenously formed nitrate- and nitrite-AFm phases are decomposed upon chloride exposure accompanied by Friedel's salts formation, potentially releasing corrosion inhibitive ions to the pore solution in a progressive manner. The NaNO{sub 2} and NaNO{sub 3} incorporation in ternary OPC-MK-DM binders marginally lowers chloride binding capacity but reduces its penetration resistance mainly due to pore coarsening. Nevertheless, a strong linear correlation can be established between the water-soluble and total chloride contents in ternary OPC-MK-DM systems, regardless of OPC replacement level and corrosion inhibitor incorporation.

36 MATERIALS SCIENCE↗

Experimental evidence for the acceleration of slag hydration in blended cements by the addition of CaCl2

Cements with high substitution rates of ground granulated blast furnace slags (GGBS) have the potential to significantly lower CO{sub 2} emissions of concrete, but their early age strength is often below those of traditional OPC cements. One way of mitigating this drawback is to use accelerating admixtures. In this study, the effect of CaCl{sub 2} additions on the hydration of blended cements was investigated by measuring compressive strength, porosity, heat release and propagation of ultrasound in blends containing 70 wt% of GGBS. The onset of formation of aluminate phases was monitored using in-situ XRD. The effect of CaCl{sub 2} on slag hydration was isolated by replacing GGBS by an inert quartz filler. Results showed that compressive strength values at one, two and seven days were increased by 50% by the CaCl{sub 2} addition. The increases in compressive strength corresponded to a reduction in pore space. GGBS hydration contributed to the heat development, structuration and compressive strength of the blended cements from 15 h. The addition of CaCl{sub 2} led to an earlier onset of the GGBS reaction, at around 10 h, and increased the rate of GGBS hydration during the first seven days. The time of onset of the GGBS contribution was also the moment when AFm precipitation started. In CaCl{sub 2}-containing blends, Cl was incorporated in AFm.

36 MATERIALS SCIENCE↗

Adsorption of silica colloids onto like-charged silica surfaces of different roughness

Particle adsorption was explored in a model optical polishing system, consisting of silica colloids and like-charged silica surfaces. The adsorption was monitored in situ under various suspension conditions, in the absence of surfactants or organic modifiers, using a quartz crystal microbalance with dissipation monitoring (QCM-D). Changes in surface coverage with particle concentration, particle size, pH, ionic strength and ionic composition were quantified by QCM-D and further characterized ex situ by atomic force microscopy (AFM). A Monte Carlo model was used to describe the kinetics of particle deposition and provide insights on scaling with particle concentration. Transitions from near-zero adsorption to measurable adsorption were compared with equilibrium predictions made using the Deraguin-Verwey-Landau-Overbeek (DLVO) theory. In addition, the impact of silica surface roughness on the propensity for particle adsorption was studied on various spatial scale lengths by intentionally roughening the QCM sensor surface using polishing methods. It was found that a change in silica surface roughness at the AFM scale from 1.3 nm root-mean-square (rms) to 2.7 nm rms resulted in an increase in silica particle adsorption of 3-fold for 50-nm diameter particles and 1.3-fold for 100-nm diameter particles—far exceeding adsorption observed by altering suspension conditions alone, potentially because roughness at the proper scale reduces the total separation distance between particle and surface.

36 MATERIALS SCIENCE↗

Effect of CO 2 on the water slip flow at silica surfaces for nanometer slit pores of talc

In our previous study, Molecular Dynamics (MD) simulated water flow with no dissolved gas in nanometer slit pores of the hydrophobic talc surfaces revealed a slip length of about 0.5 nm, which is close to the size of “water exclusion zone” but much less than experimental slip length. Atomic Force Microscopy (AFM) imaging confirmed the presence of pancake shape nanobubbles at the hydrophobic talc (001) surface (size from tens to hundreds of nanometers). The effect of CO 2 on water slip flow in talc nanopores is reported to reveal the importance of dissolved gas for confined fluid flow. MD simulated 7 nm CO 2 nanobubbles were found to attach and spread at the talc (001) surface, consistent with the AFM observation. Simulated CO 2 saturated water flow in the slit pores of talc (001) surfaces predicted the generation of CO 2 nanobubbles at the end of the slit pore, due to the stabilization of a CO 2 film at the talc (001) surfaces and a water barrier at the edge surfaces of talc. A “critical thickness” of about 1.5 nm was found for CO 2 nanobubbles to be stabilized at the end of the talc (001) surface. With 1.5 nm CO 2 nanobubbles at the talc (001) surface of a 6 nm slit pore, a water slip length of 1.8 nm was determined. Furthermore, the nanometer slit pore simulations with dissolved CO 2 in water revealed an increased slip length. It is expected that an increased slip length value would be found with an increased CO 2 film thickness.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Structure-property Relationships for Methyl-terminated Alkyl Self-assembled Monolayers

Structure-property relationships for methyl-terminated alkyl self-assembled monolayers (SAMs) are developed using near-edge X-ray absorption fine structure (NEXAFS) spectroscopy and atomic force microscopy (AFM). NEXAFS C K-edge spectra are used to compute the dichroic ratio, which provides a quantitative measure of the molecular structure. AFM data are analyzed with an elastic adhesive contact model, modified by a first-order elastic perturbation method to include substrate effects, to extract the monolayer mechanical properties. Using this approach, the measured mechanical properties are not influenced by the substrate, which allows universal structure-property relationships to be developed for methyl-terminated alkyl SAMs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Heteroepitaxial growth of cadmium carbonate at dolomite and calcite surfaces: Mechanisms and rates

Here, the systematic variation of rates and the mechanism of cadmium uptake on the (104) surface of dolomite (CaMg(CO 3 ) 2 ) were investigated using in situ and ex situ atomic force microscopy (AFM), ex situ specular X-ray reflectivity (XR), and ex situ X-ray fluorescence (XRF). Selected experiments were performed on the calcite (CaCO 3 ) (104) surface for comparison. Aqueous solutions of CdCl 2 , CaCl 2 , and NaHCO 3 , undersaturated with respect to calcite and supersaturated with respect to otavite (CdCO 3 ) and the (Cd x Ca 1-x )CO 3 solid solution, were reacted with dolomite surfaces for minutes to days. Calcite substrates were reacted with solutions containing 1-50 μM CdCl 2 , and with no added Ca or CO 3 . Thin carbonate films following the Stranski-Krastanov growth mode were observed on both substrates. Specular XR and XRF revealed the formation of nm-thick Cd-rich carbonate films that were structurally ordered with respect to the dolomite (104) plane. Epitaxial films adopted the calcite crystal structure with a d 104 - spacing (3.00 Å) larger than those of pure dolomite (2.88 Å) and otavite (2.95 Å) indicating either a solid solution with x approximate to 0.5, or a strained Cd-rich carbonate with a composition near that of otavite. The growth rate r of this phase increases with the initial supersaturation of the solution with respect to the solid solution, beta max, and follows the empirical relationship, as determined from XRF measurements, given by: r = 10 -4.88 ± 0.42 (β 2.29 ± 0.24 max - 1), (in units of atoms of Cd/Å 2 /h).The morphology of the overgrowth also varied with β max , as exemplified by AFM observations. Growth at step edges occurred over the entire β max range considered, and additional growth features including 3 Å high monolayer islands and ~ 25 Å high tall islands were observed when log β max > 1. On calcite, in situ XR indicated that this phase is similar to the Cd-rich overgrowth formed on dolomite and images obtained from X-ray reflection interface microscopy (XRIM) reveal the existence of laterally variable Cd-rich domains.

58 GEOSCIENCES↗

Glass particle resuspension from a contaminated (dirty) glass surface

A wealth of adhesion force measurements between a variety of particle/surface pairs have been gathered via Atomic Force Microscopy (AFM) in the past years. However, these measurements deal mostly with clean surfaces and particles for reproducibility. It is therefore up for debate whether particle resuspension could be calculated using these measurements as surrogates for real outdoor particles and surfaces, which often carry both organic and inorganic contaminants (“urban grime”). Two components are necessary to investigate this question: (1) adhesion force measurements on both clean and contaminated surfaces and (2) estimation of particle resuspension from both surface types. In this work, AFM was used to measure the distribution of the adhesion force between a 5-µm clean glass particle and two glass surfaces: the first cleaned according to conventional laboratory standards and a second one left outdoors for six weeks in Albuquerque (New Mexico). The Rock ‘n' Roll model was modified to use experimental adhesion force distributions of arbitrary shape and number of modes instead of a lognormal distribution, as in the original work Reeks & Hall (2001). The results of this analysis showed that the differences in the fraction of particles resuspended were small for a friction velocity of 0.5 m/s but increased for 1 and 2 m/s. For instance, for a friction velocity of 3 m/s, 71% of the original deposit was still on the surface after a day for the clean glass, while only 33% remained on the contaminated glass.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Unraveling the nature of Fe-doping mediated inter- and intra-chain interactions in Ca 3 Co 2 O 6

The structural and magnetic properties of quasi-one-dimensional (1D) spin-chain compounds Ca 3 Co 2-x Fe x O 6 (x = 0, 0.1, 0.2 and 0.3) synthesized by a sol-gel method have been systematically studied by means of X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), neutron powder diffraction (NPD), dc and ac magnetization measurements. The samples adopt a rhombohedral crystal structure with the space group R-3c in a temperature range of 5–100 K. Fe ions are found to locate at the trigonal prism Co2 crystallographic sites. Fe doping converts some of low-spin Co 3+ ions at Co1 octahedral sites into Co 2+ ions. For the high-temperature paramagnetic phase, the Curie paramagnetic temperature θp changes its sign from positive to negative at x = 0.2, implying that the dominant magnetic interaction is driven from ferromagnetic (FM) to antiferromagnetic (AFM) upon Fe substitution. A partial low-spin to high-spin state crossover of the Co1 ions is observed at high Fe-doping level x = 0.3. All the samples exhibit a long-range spin-density wave (SDW) AFM ordering below TN, followed by a spin-glass-like transition at Tf. These low-temperature magnetic phases were significantly suppressed upon Fe doping. The Fe substitution in Ca 3 Co 2-x Fe x O 6 weakened both intrachain and interchain magnetic interactions, caused by enhanced magnetic disorder due to the different magnetic characters of Ising Co and Heisenberg Fe spins.

36 MATERIALS SCIENCE↗

Contrasting magnetic properties of polymorphic TbPt 3

Here, in this work, we report the contrasting magnetic behaviour of a bimorphic intermetallic compound TbPt 3 that undergoes a structural phase transformation from cubic AuBe 5 -type structure to the cubic AuCu 3 -type structure on annealing at high temperature for a very short time. The magnetic ground state configuration of TbPt 3 changes from ferromagnetic (FM) in AuBe 5 -type crystalline phase to antiferromagnetic (AFM) in AuCu 3 -type phase. However, the AFM ground state of the AuCu 3 -type compound is unstable, as a moderate magnetic field can induce the FM character through metamagnetic transformation. To understand the said crystallographic as well as magnetic transformations, structural and magnetic ab-initio calculations have been carried out for both phases. From theoretical calculations we have proposed that although the AuBe 5 -type structure of TbPt 3 irreversibly transforms to the AuCu 3 -type TbPt 3 by a very short heat treatment, the application of moderate magnetic field on AuCu 3 -type structure may result in recovering the magnetic properties of AuBe 5 -type structure of TbPt 3 . As the two different polymorphs exist simultaneously at ambient condition, TbPt 3 thus provides us a great opportunity to study directly the effect of crystal structure on its physical properties and vice versa.

36 MATERIALS SCIENCE↗

Effects of carbon substitution on magnetic properties and magnetocaloric effects in Mn 65-x Ga 17 C 18+x compounds

This study involved the tuning of the magnetic, magnetocaloric, and room-temperature structural properties of Mn 65-x Ga 17 C 18+x (0 ≤ x ≤ 4) compounds prepared using a high-energy ball milling (HEBM) technique. This study indicates that the crystal structure of all the compounds can be described as an anti-perovskite cubic structure with the Pm-3m space group and the crystal cell volume decreases with increasing carbon concentration. The system shows a first-order structural phase transition at a temperature T=T M between two cubic phases having different magnetic structures. The phases are characterized by antiferromagnetic (AFM) and ferromagnetic (FM) -like behavior at low (T < T M ) and high (T M > T) temperature regions, respectively. A suppression of the AFM phase was observed with increasing C concentration. The temperature-induced first-order transitions (FOTs) were found to possess a small thermal hysteresis in the magnetization (~2-3 K) in an applied magnetic field of H = 50 kOe. Magnetic entropy changes estimated from isothermal magnetization curves indicate that the largest value of the magnetic entropy change of |ΔS M | = 2.1 J kg -1 K -1 for x = 4 with ΔH = 50 kOe, with a relative cooling power (RCP) of ~190 J kg -1 . Furthermore, high-energy ball milling (HEBM), a scalable technique, has been demonstrated as a viable method to synthesize magnetocaloric materials with substantial RCP values.

36 MATERIALS SCIENCE↗

Influence of Radioactivity on Surface Interaction Forces

Although some differences have been observed, the transport behavior of radioactive aerosol particles has often been assumed to be analogous to the behavior of nonradioactive aerosols in dispersion models. However, radioactive particles can become electrostatically charged as a result of the decay process. Theories have been proposed to describe this self-charging phenomenon, which may have a significant effect on how these particles interact with one another and with charged surfaces in the environment. In this study, atomic force microscopy (AFM) was employed to quantify surface forces between a particle and a planar surface and to compare measurements with and without the involvement of radioactivity. The main objective of this work is to assess directly the effects of radioactivity on the surface interactions of radioactive aerosols via the measurement of the adhesion force. The adhesion force between a silicon nitride AFM tip and an activated gold substrate was measured so that any possible effects due to radioactivity could be observed. The adhesion force between the tip and the gold surface increased significantly when the gold substrate (25 mm{sup 2} surface area) was activated to a level of approximately 0.6 mCi. The results of this investigation will prompt further work into the effects of radioactivity in particle-surface interactions.

36 MATERIALS SCIENCE↗

The effect of cooling rate on magnetothermal properties of Fe 49 Rh 51

In this report, we have explored the effects of quenching rate on the thermal dependence of the magnetic entropy change ΔS M (T) and the magnetic field induced hysteresis loss through the antiferromagnetic (AFM)↔ferromagnetic (FM) transformation in bulk Fe 49 Rh 51 . Two nearly identical square-prism-shaped samples were subjected to two different temperature cooling regimes; one was rapidly quenched (FQ) in iced-water and another slow cooled (SC) to room temperature at a cooling rate of 2 K/min. The temperature of the AFM↔FM transition is similar for both samples, but the FQ sample shows much sharper temperature- and magnetic field-induced magnetization change; in addition, the total magnetization change is 14% larger. In FQ material, the magnetocaloric effect, i.e., ΔS M (T) quickly approaches saturation above 1 T and shows a large peak value at 2 T (13.9 versus 8.9 Jkg –1 K –1 in SC material), yet a larger average hysteresis loss FWHM in the temperature range coinciding with of the full-width at half-maximum of the ΔS M (T) curve.

36 MATERIALS SCIENCE↗

Metamagnetism and kinetic arrest in a long-range ferromagnetically ordered multicaloric double perovskite Y 2 CoMnO 6

A systematic magnetic study of the double perovskite oxide Y 2 CoMnO 6 (YCMO) has been performed. A monoclinic P21/n phase of YCMO was synthesized using a sol-gel method. Neutron diffraction (ND) measurements evidence the onset of long-range ferromagnetic (FM) ordering at TC ~ 76 K, which persists down to 5 K. The presence of 25% antisite disorder, estimated from the ND data, leads to the appearance of short-range antiferromagnetic (AFM) interactions. The existence of thermal hysteresis due to competing interactions between FM and AFM phases is observed in the M vs. T measurements. The pinning of magnetic domain walls at the Co/Mn antiphase boundaries results in a metamagnetic-like behavior. The field dependence of thermomagnetic irreversibility and the nature of virgin curves indicate the occurrence of a kinetic arrest phenomenon, which is further verified via cooling and heating of the system in an unequal fields (CHUF) protocol. In full agreement with the ND data, a detailed analysis of critical exponents near the paramagnetic (PM)-FM phase transition also establishes YCMO as a long-range interacting mean-field system. A close examination of the temperature- and field-dependent magnetic entropy change yields an in-depth understanding of coexisting magnetically ordered and disordered phases in YCMO, leading to a comprehensive magnetic phase diagram of this multifunctional double perovskite system.

36 MATERIALS SCIENCE↗

Crystal and magnetic structure of polar oxide HoCrWO 6

In this study, polar magnetic oxide HoCrWO 6 is synthesized and its crystal structure, magnetic structure, and thermodynamic properties are investigated. HoCrWO 6 forms the polar crystal structure (space group Pna 2 1 (#33)) due to the cation ordering of W 6+ and Cr 3+ . There is an antiferromagnetic transition at T N = 24.5 K along with the magnetic entropy change (~5 J.Kg. –1 K –1 at 70 kOe). Neutron diffraction measurement indicates that both Cr and Ho sublattices are ordered with the moment of 2.32(5)μ B and 8.7(4)μ B at 2 K, respectively. While Cr forms A-type collinear antiferromagnetic (AFM) structure with magnetic moment along the b axis, Ho sublattice orders in a non-coplanar AFM arrangement. A comparison with isostructural DyFeWO 6 and DyCrWO 6 indicates that the magnetic structure of this family of compounds is controlled by the presence or absence of e g electrons in the transition metal sublattice.

42 ENGINEERING↗