SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Accelerated laboratory test for evaluation of stress corrosion susceptibility of ferrous and nickel alloys in seashore environment
For proposed long-duration NASA Space Science missions, the Department of Energy, Lockheed Martin, Infinia Corporation, and NASA Glenn Research Center are developing a high-efficiency, 110 W Stirling Radioisotope Generator (SRG110). A structurally significant limit state for the SRG110 heater head component is creep deformation induced at high material temperature and low stress level. Conventional investigations of creep behavior adequately rely on experimental results from uniaxial creep specimens, and a wealth of creep data is available for the Inconel 718 material of construction. However, the specified atypical thin heater head material is fine-grained with a heat treatment that limits precipitate growth, and little creep property data for this microstructure is available in the literature. In addition, the geometry and loading conditions apply a multiaxial stress state on the component, far from the conditions of uniaxial testing. For these reasons, an extensive experimental investigation is ongoing to aid in accurately assessing the durability of the SRG110 heater head. This investigation supplements uniaxial creep testing with pneumatic testing of heater head-like pressure vessels at design temperature with stress levels ranging from approximately the design stress to several times that. This paper presents experimental results, post-test microstructural analyses, and conclusions for four higher-stress, accelerated life tests. Analysts are using these results to calibrate deterministic and probabilistic analytical creep models of the SRG110 heater head.
There are many photovoltaic (PV) applications where lighter weight and/or bendable PV power would be beneficial. This includes the curved surfaces of buildings, buildings with weight limitations, boats, automobiles, or other portable applications. In many of these cases, the bending will be only a single occurrence at installation or the amount of bending, even if repeated, is not dramatic. This allows for crystalline silicon modules to be used. For flexible applications, the dominant material for the frontsheet is polyethylene tetrafluoroethylene (PETFE). As a fluoropolymer it resists soiling, is UV stable, and PETFE is a more mechanically durable fluoropolymer. However, in the interests of keeping costs down, less expensive alternative polymers are desirable. In this study, highly accelerated ultraviolet light and heat stresses are applied to candidate materials and the degradation kinetics are determined to provide information to evaluate their suitability for use in a PV application.
This paper reports the interim results of the Earth Observing System AM-1 project (EOS-AM-1) nickel hydrogen cell life test being conducted under contract to National Aeronautics and Space Administration (NASA) Goddard Space Flight Center (GSFC) at the Lockheed Martin Missiles and Space (LMMS) facility in East Windsor, NJ; and at COMSAT Labs., Clarksburg, MD. The purpose of the tests is to verify that the EOS-AM-l cell design can meet five years of real-time Low Earth Orbit (LEO) cycling. The tests include both real-time LEO and accelerated stress tests. At LMMS, the first real-time LEO simulated 99 minute orbital cycle started on February 7, 1994 and the test has been running continuously since that time, with 13000 LEO cycles completed as of September 2, 1996. Each cycle consists of a 64 minute charge (VT at 1.507 volts per cell, 1.06 C/D ratio, followed by 0.6 ampere trickle charge) and a 35 minute constant power discharge at 177 watts (22.5% DOD). At COMSAT, the accelerated stress test consists of 90 minute orbital cycles at 60% DOD with a 30 minute discharge at 60 amperes and a 60 minute charge at 40 ampercs (VT at 1.54 volts per cell to 1.09 C/D ratio, followed by 0.6 ampere trickle charge). The real-time LEO life test battery consists of seven, 50AH (nameplate rating) Eagle-Picher, Inc. (EPI) Mantech cells manufactured into three, 3-cell pack assemblies (there are two place holder cells that are not part of the life test electrical circuit). The test pack is configured to simulate the conductive thermal design of the spacecraft battely, including: conductive aluminum sleeves, 3-cell pack aluminum baseplate, and honeycomb panel all mounted to a liquid (-5 C) cold plate. The entire assembly is located in a thermal chamber operating at +3 C. The accelerated stress test unit consists of five cells mounted in machined aluminum test sleeves and is operating at +10 C. The real-time LEO life test battery has met all performance requirements through the first 13,000 cycles, including: end of charge and discharge cell voltages and voltage gradients; end of chalge and discharge cell pressures; within cell and between cell temperature gradients; discharge capacity; current and power levels; and all chalge parameters. The accelerated stress test battely has completed over 5900 cycles as of 9/11/96. This paper reports both battery performances as a function of cycle life, with individual cell performance comparisons repolted for selected cycles in both tests.
The Advanced Vehicle Testing and Evaluation (AVTE) project incorporated the conduct of advanced technology vehicle and infrastructure testing in the U.S. Department of Energy (DOE) Advanced Vehicle Testing Activity (AVTA). It was the only activity tasked by DOE to conduct independent field evaluations of vehicle technologies that use advanced technology systems and subsystems in vehicles that reduce petroleum consumption. The results are available through reports published on the AVTA website at http://avt.inl.gov/. The AVTE project provided insight into advanced vehicle technology's long-term performance, durability, maintenance, and lifecycle costs that cannot be found elsewhere. The site is a resource for DOE stakeholders and the public to gain knowledge on advanced technology vehicle progress and innovation. Vehicles tested included light and heavy-duty vehicles with conventional, hybrid, plug-in hybrid, and all-electric propulsion systems. Vehicles were tested on closed tracks and chassis dynamometers, as well as operated on public roads, in fleet operations, and over prescribed routes. All testing was controlled by procedures developed specifically to support such testing. Testing and evaluations were conducted in the following phases: Development and refinement of test procedures, which established testing procedures; Baseline performance testing, which established a performance baseline; Accelerated reliability testing, which determined vehicle reliability; Fleet testing, used to evaluate vehicle economics in fleet operation, and End of test performance evaluation. Test results from all aspects of testing were posted by Idaho National Laboratory (INL) to their website. This final report documents work conducted for the entirety of contract DE-EE0005501 by Intertek Testing Services NA, Inc. (Intertek). The contract was performed from October 1, 2011 through April 30, 2018, and includes 18 amendments to the original award with the most recent Amendment 18 dated March 28, 2018. The final budget for the AVTE project totaled 20,220,873 dollars. As a cooperative agreement, Intertek was obligated to provide cost share of 4,044,175 dollars, leaving 16,176,698 dollars as the Federal share of the agreement. Actual total expenditure for the AVTE project was 20,286,850 dollars. The full 16,176,698 dollars Federal share was expended and 4,110,152 dollars of cost share was provided by Intertek. This resulted in an over-share of 65,977 dollars. There were 106 light-duty on-road vehicles vehicles tested in both fleet and accelerated reliability testing. One additional vehicle was rented to obtain performance testing only. Three heavy-duty truck and trailer combinations were tested as part of the semi-autonomous driving with heavy-duty vehicles in a platoon. Overall project scope and direction was determined between Intertek, DOE, and technical teams from Idaho National Laboratory (INL), Argonne National Laboratory (ANL), and National Renewable Energy Laboratory (NREL). The project was administered by the DOE’s National Energy Technology Laboratory (NETL).
MAX phases have recently attracted significant attention for potential nuclear applications due to their novel properties such as unique hexagonal-compact nanolayered crystal structure, high-machinability due to lower hardness levels compared to conventional ceramics, and high-chemical inertness. In order for MAX phases to be used in nuclear reactors, two aspects deserve detailed investigations: (i) their phase stability at high-temperatures and (ii) microstructural defect formation and recovery induced by energetic particle irradiation. To date, degradation mechanisms of MAX phases at high-temperatures and following irradiation are largely unexplored fields of research. This work focuses on the evaluation of two Ti-based MAX phases – Ti 2 AlC and Ti 3 SiC 2 – within the context of extreme environments. To accomplish this, a one-of-a-kind comparison between neutron irradiations, performed over a decade of research at the High Flux Isotope Reactor (HFIR), and heavy-ion irradiations, carried out in situ in a Transmission Electron Microscope (TEM) at the MIAMI-2 facility, has been conducted. The results show Ti-based MAX phases are prone to accelerated decomposition under the conditions investigated. This questions the hypothesis that MAX phases exhibit high phase stability, especially when used in future nuclear energy systems where energetic particle irradiation is a dominating degradation mechanism.
This DuraMAT project intends to identify bill of materials (BOM) and/or process control measures for photovoltaic modules with representative failure modes as informed by accelerated and field tests to guide next steps in module and material design. We have begun work to identify correlation between module field performance and accelerated testing results by cross-comparing a module database of accelerated test results with a module database of fielded systems. We have identified fielded systems with degraded performance, and intend to compare this to the results observed in certification and qualification testing. We also intend to apply lessons and observations from accelerated tests to the field, where it may be possible to mitigate or avoid degradation in the field.
This study demonstrates the efficacy of supplementary cementitious materials (SCMs) to mitigate alkali-silica reaction (ASR) even when used in conjunction with cement of higher alkali contents (up to 1% Na{sub 2}O{sub eq}). The expansion of concrete prisms was studied immersed in simulated pore solution in order to address the limitations of conventional ASR testing methods, accelerated mortar bar test (AMBT) and concrete prism test (CPT). Expansion results demonstrate that 25% fly ash and 50% slag are both sufficient to mitigate ASR even with cements with alkali content up to 1% Na{sub 2}O{sub eq} and that the pore solution method is a viable alternative ASR testing method. Massive amounts of ASR products (~20 μm thickness) were observed in concretes without SCMs consistent with high degree of expansion and extensive cracking. Small amounts of ASR products (≤5 μm thickness) were also observed in concrete with SCMs despite absence of significant expansion.
Not Available
Biomass feedstocks have been shown to cause high wear rates on biomass processing equipment, including grinders, pneumatic conveyance systems, and screw feeders. Previously, wear rates were positively correlated with ash concentrations. Physical and chemical properties, including ash content, vary across the anatomy of plants in biomass feedstocks. To better understand biomass tissues that cause the most wear, anatomical fractions of pine forest residues were tested for wear properties. Fractions were tested in the Accelerated Wear Testing Apparatus using steel coupon mass loss to evaluate wear rates. Extrinsic ash was extracted and characterized. Total ash content of the forest residue was 0.80wt%. Anatomical fractions showed varied amounts of ash with highest concentrations in bark and needles (2.33wt%, 3.52wt%, respectively). The wear rate of the forest residue was 2.36mg loss per kg biomass. Low ash fractions, including whitewood and cambium, caused little wear. Bark had lower ash than the needles but resulted in more wear (8.63 vs 5.57mg loss per kg biomass). Bark contained the most extrinsic ash and largest ash particle size, while needles contained the least extrinsic ash and smallest ash particle size. These findings indicate that total ash content (intrinsic plus extrinsic), soil contamination, and elemental analysis can provide information related to wear properties of biomass materials; however, these analyses do not fully explain the differences observed in the wear rates of bark and needles. Additional testing is to determine other parameters of importance.
The Geothermal Entrepreneurship Organization launched in 2019 with the goal of building a geothermal innovation ecosystem at the University of Texas at Austin (UT Austin), and in the State of Texas at large. The theses underlying the work of GEO were 1) that with targeted advocacy, recruitment, organization, and coalition building, research institutions with legacy excellence in petroleum and geosystems engineering could become engines of geothermal innovation, research and development; 2) that startups were the appropriate vehicle to speed these innovations from the lab into the field, and building a geothermal startup ecosystem in Texas would not only advance next generation geothermal concepts into the field, but also help spur oil and gas engagement in the space, and 3) that with targeted engagement, education, and recruitment across stakeholders in the oil and gas industry and the State of Texas generally, the oil and gas industry, and other legacy oil and gas entities in the State could become sources of large scale deployment of geothermal energy. The overall goal was to create a ‘snowball’ effect, where targeted impactful actions would catalyze self-sustaining, organic growth of a new geothermal ecosystem in the State of Texas. That goal was achieved through GEO’s work. To test its theses, GEO began work by interviewing and recruiting UT Austin faculty and alumni into geothermal. At the beginning of the GEO project, there was no geothermal activity ongoing within the UT Austin Petroleum and Geosystems Engineering Department, the Bureau of Economic Geology, or the Jackson School of Geoscience, and many faculty approached had not before considered how their skillsets might apply in the space. By the end of the project period, three major research consortia focused on geothermal were launched as a result of GEO’s work, one at the Bureau of Economic Geology, one within the Petroleum and Geosystems Engineering Department, and another organized by GEO across six research institutions across the State of Texas, called the Texas Geothermal Institute. Geothermal curricula was launched at UT Austin, and UT Austin began attracting new geothermal enthusiasts into its faculty, including Dr. Silviu Livescu, former Chief Scientist of Baker Hughes. Startups recruited and mentored by GEO launched, raised funding, and deployed (or are currently deploying) their concepts in the field. By the end of the project period, the GEO concept expanded to faculty beyond UT Austin to other institutions, like Texas A&M, the University of Houston, and Rice University, and geothermal engagement began at those institutions as well. Multiple faculty members and alumni across these institutions launched geothermal startup companies, launched geothermal research consortia, and/or began teaching geothermal courses. In 2020, GEO launched what was to become the largest geothermal conference in the world by its second year, ‘PIVOT – From Hydrocarbons to Heat’, and the resulting momentum catalyzed the Society of Petroleum Engineers to launch a geothermal technical section, drove more startups to launch out of the ecosystem, and drove actors in the State of Texas, NGOs, and stakeholders globally to become engaged. Riding this momentum, the Texas Geothermal Energy Alliance was launched, the first ever industry association dedicated to advancing geothermal energy in the State of Texas. The Texas geothermal ecosystem after only two years of building and support is now robust, quickly growing, and self-sustaining. By 2021, the Texas geothermal ecosystem had attracted the attention of philanthropists, funding entities, media, and influencers outside of Texas, and GEO’s executive director was invited to give a TED talk about oil and gas engagement in building the future of geothermal energy, which elevated the success of the ecosystem to a global audience.
Structures made from a combination of aluminum alloy (AA) and carbon fiber-reinforced plastic (CFRP) are susceptible to galvanic corrosion of the AA in harsh atmospheric conditions, such as might exist for closure panels in automotive applications. It is important to understand the galvanic corrosion behavior of these materials under laboratory conditions as that might allow prediction of performance in real environments. This work tested specially designed AA6×××-CFRP coupons, including AA6111 and AA6022, connected to CFRP made from two different carbon fiber fabrics (twill and random) with the aim of understanding the corrosion behaviors in a laboratory cyclic exposure chamber and during on-road exposure. The extent of corrosion was assessed by galvanic current measurements, optical profilometry, cross-sectional area analysis, and microscopic analysis. Based on the results, it was determined that the corrosion susceptibilities and morphologies observed in CFRP/AA couples tested in an environmental chamber for 12 weeks were in correspondence with those of the coupons subjected to on-road testing for 1 y in Columbus, OH.
High strength ferrous alloys susceptibility to stress corrosion in seacoast environment, tension loading single edge notched and fatigue cracked specimens in NaCl solution
Improved cadmium electrode substrates with precisely controlled microstructures for possible use in aerospace nickel-cadmium cells were prepared. The preparative technique was a powder metallurgical process in which a fugitive pore-former and a nickel powder were blended, then isostatically compacted, and subsequently sintered. Cadmium electrodes prepared from such substrates were cycle tested using an accelerated tortuous test regime. It was discovered that plaques of 60% or 80% porosity prepared with a 25 micron pore-former were better than state-of-the-art electrodes in terms of efficienty and/or mechanical strength. The 60% structures were particularly outstanding in this respect in that they had efficiencies only 5-10 percentage points lower than state-of-the-art electrodes and vastly superior mechanical properties. This added strength was observed to eliminate cracking and physical degradation of the electrodes during processing and cycling. The cadmium electrodes prepared from the 80% porous substrates proved to be the best electrodes made during the course of the work from the point of view of highest efficiency. Three-point bend tests were used to measure mechanical properties of the plaques produced and also as a general characterization tool. In addition, the BET surface areas of selected specimens was determined. The SEM was used for judging microscopic uniformity and quantitatively determining the induced pore size and various other fine structures in the substrates. The technique of X-ray radiography was used to follow the bulk uniformity of the substrates at various stages of their processing.
Materials for solar-cell module construction have been studied on the basis of limited real-time outdoor exposure evaluations. The materials tested included transmission samples, sub-modules, and actual solar cells. The results suggest that glass, fluorinated ethylene propylene, and perfluoroalkoxy are good materials for the covering or encapsulation of solar-cell modules. In all cases, dirt accumulation and cleanability are important factors.
Progress in identification of strengths and weaknesses of amorphous-silicon technology detailed. Report describes achievements in testing reliability of solar-power modules made of amorphous-silicon photovoltaic cells. Based on investigation of modules made by U.S. manufacturers. Modules subjected to field tests, to accelerated-aging tests in laboratory, and to standard sequence of qualification tests developed for modules of crystalline-silicon cells.
Application of a diagnostic system to a helicopter gearbox is presented. The diagnostic system is a nonparametric pattern classifier that uses a multi-valued influence matrix (MVIM) as its diagnostic model and benefits from a fast learning algorithm that enables it to estimate its diagnostic model from a small number of measurement-fault data. To test this diagnostic system, vibration measurements were collected from a helicopter gearbox test stand during accelerated fatigue tests and at various fault instances. The diagnostic results indicate that the MVIM system can accurately detect and diagnose various gearbox faults so long as they are included in training.