Search NASA⌕ Search

SEARCH · Search NASA

Results for “Behavior analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42

Design of bonded joints in composite materials

The primary form of joining high strength advanced composite materials is adhesive bonded joints. The stepped bonded joint is an efficient configuration where the adhesive and composite matrix are co-cured. A design procedure for this type of joint is described along with the analysis technique upon which it is based. A modified elastic analysis accounts for the nonlinear behavior of the adhesive. A computer program with minimum running time and simplified input is utilized for analysis and becomes an efficient link in an iterative design procedure. Comparisons between analytical results and test results are shown. Material properties which are needed for design and methods of measuring these properties are discussed.

Corvelli, N.↗

Subsynchronous instability of a geared centrifugal compressor of overhung design

The original design analysis and shop test data are presented for a three stage (poster) air compressor with impellers mounted on the extensions of a twin pinion gear, and driven by an 8000 hp synchronous motor. Also included are field test data, subsequent rotor dynamics analysis, modifications, and final rotor behavior. A subsynchronous instability existed on a geared, overhung rotor. State-of-the-art rotor dynamics analysis techniques provided a reasonable analytical model of the rotor. A bearing modification arrived at analytically eliminated the instability.

Hudson, J. H.↗

Unraveling the multi-step crystallization mechanism of polytetrafluoroethylene, modified polytetrafluoroethylene, and their nanocomposites with boron nitride nanobarbs: Experimental insights and theoretical analysis

The non-isothermal crystallization behavior and kinetics of polytetrafluoroethylene (PTFE) composites with boron nitride nanobarb (BNNB), a new generation nanostructure with unique surface morphology and mechanical “barbs” have been analyzed, understanding these properties is essential for their high-end applications as thermal interface materials (TIM) for microwave, 5G and microelectronic devices. The analysis of the crystallization parameters includes crystallization onset, peak and end temperatures, crystallization half-life and overall crystallinity of PTFE, modified PTFE and their BNNB composites. The results were further analyzed using theoretical models such as the combined Avrami-Ozawa model. It was found that BNNB supports crystallization in the modified PTFE but shows minimal effect on the crystallization of PTFE. Due to the limitation of the classical theoretical models used above in fully characterizing the multi-step crystallization process of PTFE, an in-depth analysis using the model-free advanced isoconversional computation was used to characterize the PTFE crystallization based on the evolution of activation energy with fractional crystallinity and for the first time with temperature. Three kinetic regions were identified in the crystallization mechanism. Here, this study investigated the molecular organization and microstructural evolution of PTFE, modified PTFE and their composites during non-isothermal crystallization using advanced X-ray scattering measurements. An insight into the changes undergone by the material's microstructural units including crystallite size and morphology, lamellar thickness and lamellar interfacial layer thickness, and crystallographic phase dynamics during non-isothermal cooling from the melt, was provided here in this work. The effect of copolymer modification of PTFE and the inclusion of pristine and functionalized BNNB (a thermally conductive and electrically insulating ceramic) are both new investigations that provide valuable knowledge for the development of materials with strong matrix-nanofiller interaction and guidance for optimizing sintering and cooling cycles, two key steps in PTFE processing that largely affect the material microstructural features. Overall, the result of the three-part investigation demonstrates that BNNB supports crystallization in the modified PTFE up to 20 wt% concentration and at low and high cooling rates typically used in the industrial processing of PTFE.

36 MATERIALS SCIENCE↗

Resolving the Extragalactic γ -Ray Background above 50 GeV with the Fermi Large Area Telescope

The Fermi Large Area Telescope (LAT) Collaboration has recently released a catalog of 360 sources detected above 50 GeV (2FHL). This catalog was obtained using 80 months of data re-processed with Pass 8, the newest event-level analysis, which significantly improves the acceptance and angular resolution of the instrument. Most of the 2FHL sources at high Galactic latitude are blazars. In this paper, using detailed Monte Carlo simulations, we measure, for the first time, the source count distribution, dN/dS, of extragalactic γ-ray sources at E > 50 GeV and find that it is compatible with a Euclidean distribution down to the lowest measured source flux in the 2FHL (~8 x 10 -12 ph cm -2 s -1 ). We employ a one-point photon fluctuation analysis to constrain the behavior of dN/dS below the source detection threshold. Overall, the source count distribution is constrained over three decades in flux and found compatible with a broken power law with a break flux, S b , in the range [8 x 10 -12 , 1.5 x 10 -11 ] ph cm -2 s -1 and power-law indices below and above the break of α 2 ϵ [1.60, 1.75] and α 1 = 2.49 ± 0.12, respectively. Integration of dN/dS shows that point sources account for at least 86$+16\atop{-14}$ % of the total extragalactic γ-ray background. The simple form of the derived source count distribution is consistent with a single population (i.e., blazars) dominating the source counts to the minimum flux explored by this analysis. Finally, we estimate the density of sources detectable in blind surveys that will be performed in the coming years by the Cherenkov Telescope Array.

79 ASTRONOMY AND ASTROPHYSICS↗

Probing the Effects of the First Atomic Layer on the Dynamic Behavior of Sub-2 nm MgO/Al 2 O 3 Memristors

As electronic devices continue to scale down from the current sub-5 nm range, atomic-scale control of defects becomes increasingly crucial to suppressing their impact on the physical properties of the devices. Memristors present an excellent example as a nonlinear and dynamic device with high speed and endurance required for electronic applications ranging from neuromorphic computing to nonvolatile memories. Herein we investigate the impact of atomic defects in sub-2 nm thick MgO/Al 2 O 3 atomic layer stack (ALS) memristors that use an M1 (switching layer)/M2 (oxygen vacancy reservoir layer) bilayer structure grown using in vacuo atomic layer deposition (iALD). Intriguingly, we revealed a direct correlation of the atomic defects in the M2 layer with the memristor dynamic behavior using a combined analysis of in situ scanning tunneling spectroscopy (iSTS) on the M2 layer and ex situ characterization on the memristors. Specifically, incomplete coverage of the 1st ALD atomic layer of M2 on the electrode yields defects at the M2/electrode interface. Despite the monotonic increase of ALD coverage, by almost three-fold from ~30% to >90%, at completion of the M2 layer of ~ 0.7 nm in thickness, the impact of the defects on the M2/electrode interface has been found detrimental to both memristor switching speed and endurance. Guided by atomistic simulation, we addressed the issue of interface defects via tuning of the Al surface hydroxylation to increase the first atomic layer ALD coverage to ~75%, leading to improved memristor switching speed and endurance by several orders of magnitude. In conclusion, these findings shed light on the correlation between the atomic defects and the dynamic behavior of sub-2 nm memristors and the importance of minimizing the atomic defects in memristors for future electronic applications.

Atomic Layer Deposition↗

Intrepid MCMC: Metropolis-Hastings with exploration

In engineering examples, one often encounters the need to sample from unnormalized distributions with complex shapes that may also be implicitly defined through a physical or numerical simulation model, making it computationally expensive to evaluate the associated density function. For such cases, MCMC has proven to be an invaluable tool. Random-walk Metropolis Methods (also known as Metropolis-Hastings (MH)), in particular, are highly popular for their simplicity, flexibility, and ease of implementation. However, most MH algorithms suffer from significant limitations when attempting to sample from distributions with multiple modes (particularly disconnected ones). Here, in this paper, we present Intrepid MCMC - a novel MH scheme that utilizes a simple coordinate transformation to significantly improve the mode-finding ability and convergence rate to the target distribution of random-walk Markov chains while retaining most of the simplicity of the vanilla MH paradigm. Through multiple examples, we showcase the improvement in the performance of Intrepid MCMC over vanilla MH for a wide variety of target distribution shapes. We also provide an analysis of the mixing behavior of the Intrepid Markov chain, as well as the efficiency of our algorithm for increasing dimensions. A thorough discussion is presented on the practical implementation of the Intrepid MCMC algorithm. Finally, its utility is highlighted through a Bayesian parameter inference problem for a two-degree-of-freedom oscillator under free vibration.

97 - MATHEMATICS AND COMPUTING↗

Direct Carbothermic Reduction of Weathered Ilmenite for Efficient Removal of Iron by Leaching

The commercial processes to extract iron from ilmenite (FeTiO{sub 3}) essentially include energy-intensive methods, such as high-temperature reduction smelting or preoxidation, coupled with reduction by carbon. However, due to altered mineralogy of ilmenite caused by weathering at sea coast, the reduction of iron remains incomplete in either of these processes, demanding a high concentration of acid when used for extraction of high-purity TiO{sub 2} for high-end applications. We developed a process for the flux-catalyzed reduction of a partially weathered ilmenite ore of Indian origin. Initially, the effect of flux material and temperature was evaluated using thermogravimetric/diffraction thermal analysis (TG/DTA). The reduction behavior of the fluxed self-reducing pellets of ilmenite was then studied in a raising hearth furnace. The TG/DTA results indicated improved performance of sodium carbonate over lime within a temperature range of 1173 K to 1373 K. Under different reduction conditions in raising hearth furnace experiments, the leaching of reduced ilmenite in diluted hydrochloric acid (6.6 pct concentration) produced different grades of synthetic rutile. The best reduction conditions under optimized parameters enhanced the TiO{sub 2} from initial 51 to 93 wt pct in the synthetic rutile. The X-ray diffraction and electron probe microanalysis investigation of the unreduced and reduced ilmenite revealed the conversion of the Fe{sub x}O{sub y}-SiO{sub 2}-Al{sub 2}O{sub 3} system to Na{sub 2}O-SiO{sub 2}-Al{sub 2}O{sub 3} by sodium carbonate. The thermochemical analysis further explained the influence of sodium carbonate on the liquidus of Na{sub 2}O-SiO{sub 2}-Al{sub 2}O{sub 3} slag. The improved process enables the complete reduction of the iron from weathered ilmenite to produce a high-grade rutile.

36 MATERIALS SCIENCE↗

Hierarchical Simulation to Assess Hardware and Software Dependability

This thesis presents a method for conducting hierarchical simulations to assess system hardware and software dependability. The method is intended to model embedded microprocessor systems. A key contribution of the thesis is the idea of using fault dictionaries to propagate fault effects upward from the level of abstraction where a fault model is assumed to the system level where the ultimate impact of the fault is observed. A second important contribution is the analysis of the software behavior under faults as well as the hardware behavior. The simulation method is demonstrated and validated in four case studies analyzing Myrinet, a commercial, high-speed networking system. One key result from the case studies shows that the simulation method predicts the same fault impact 87.5% of the time as is obtained by similar fault injections into a real Myrinet system. Reasons for the remaining discrepancy are examined in the thesis. A second key result shows the reduction in the number of simulations needed due to the fault dictionary method. In one case study, 500 faults were injected at the chip level, but only 255 propagated to the system level. Of these 255 faults, 110 shared identical fault dictionary entries at the system level and so did not need to be resimulated. The necessary number of system-level simulations was therefore reduced from 500 to 145. Finally, the case studies show how the simulation method can be used to improve the dependability of the target system. The simulation analysis was used to add recovery to the target software for the most common fault propagation mechanisms that would cause the software to hang. After the modification, the number of hangs was reduced by 60% for fault injections into the real system.

Ries, Gregory Lawrence↗

Development of an analysis for the determination of coupled helicopter rotor/control system dynamic response. Part 1: Analysis and applications

A theoretical analysis is developed for a coupled helicopter rotor system to allow determination of the loads and dynamic response behavior of helicopter rotor systems in both steady-state forward flight and maneuvers. The effects of an anisotropically supported swashplate or gyroscope control system and a deformed free wake on the rotor system dynamic response behavior are included in the analysis.

Sutton, L. R.↗

Vortex information display system program description manual

A vortex information display system is described which provides flexible control through system-user interaction for collecting wing-tip-trailing vortex data, processing this data in real time, displaying the processed data, storing raw data on magnetic tape, and post processing raw data. The data is received from two asynchronous laser Doppler velocimeters (LDV's) and includes position, velocity, and intensity information. The raw data is written onto magnetic tape for permanent storage and is also processed in real time to locate vortices and plot their positions as a function of time. The interactive capability enables the user to make real time adjustments in processing data and provides a better definition of vortex behavior. Displaying the vortex information in real time produces a feedback capability to the LDV system operator allowing adjustments to be made in the collection of raw data. Both raw data and processing can be continually upgraded during flyby testing to improve vortex behavior studies. The post-analysis capability permits the analyst to perform in-depth studies of test data and to modify vortex behavior models to improve transport predictions.

Conway, R.↗

Mathematical Model For Engineering Analysis And Optimization

Computational support for engineering design process reveals behavior of designed system in response to external stimuli; and finds out how behavior modified by changing physical attributes of system. System-sensitivity analysis combined with extrapolation forms model of design complementary to model of behavior, capable of direct simulation of effects of changes in design variables. Algorithms developed for this method applicable to design of large engineering systems, especially those consisting of several subsystems involving many disciplines.

Sobieski, Jaroslaw↗

Thermal loading effects on chalk hydromechanical behavior for nuclear waste disposal

Safe disposal of heat-generating nuclear waste depends on host rock stability under thermal, hydrological, and mechanical stresses. This study investigates the effect of thermal loading on mechanical behavior of the shallowly buried Ghareb formation chalk through triaxial and hydrostatic constant strain rate and creep tests at temperatures up to 100 ˚C and effective pressures up to 20.7 MPa. Experimental results show that thermal loading reduces the elastic moduli of chalk by 50–75%, and a transition occurs above 60 ˚C where creep rates increase rapidly. Water saturation nearly doubles the thermally induced strain compared to dry conditions and strongly decreases material rigidity. Thermal loading also leads to significant pore pressure increases under undrained conditions and leads to reductions in the apparent permeability during drained conditions. Laboratory experimental data were used to parameterize and develop a preliminary constitutive model for predicting future deformation during repository operations in the Ghareb. The strongly coupled effects – mechanical weakening, fluid pressure fluctuations, and permeability modification – demonstrate that elevated repository temperatures will have a pronounced effect on the near field Ghareb behavior during waste disposal operations. The findings indicate that the coupled interactions must be considered in predictive models and repository design to ensure long-term nuclear waste isolation and safety.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Sensitivity of the ACCP Value Framework Science Benefit Score

NASA’s priorities for Earth Science are informed by the 2017-2027 Decadal Survey for Earth Science and Applications from Space of the National Academies of Sciences, Engineering and Medicine. In that document, five Designated Observables are identified as priorities for implementation: Aerosols, Cloud-Convection-Precipitation, Surface Biology, Mass Change, and Surface Deformation Change. In 2019, NASA initiated four multi-year studies to formulate, assess, and recommend potential Observing System concepts that are responsive to the recommendations of the Earth Science Decadal Survey. The Aerosols, Clouds, Convection, and Precipitation (ACCP) study investigates opportunities for synergistic science resulting from implementations that combine both Aerosols science objectives and Clouds, Convection, and Precipitation science objectives. For the ACCP study, a Value Framework was designed to introduce structure, transparency, and traceability in the mission down-select decision process. This paper presents a sensitivity analysis that was conducted to characterize the behavior of the science benefit score of the ACCP Value Framework. it includes derivations of the sensitivity analysis equations, numerical analyses of the behavior of the combined benefit score, and the conclusions drawn from the results of the work that was conducted. The results of this analysis were key to ensuring that the aggregated science benefit scores would enable the team to differentiate and contrast across concepts.

John McLaughlan↗

Analysis of SETI data collected in the parasitic mode

A system for performing SETI observations continuously as part of non-SETI observations at a radio observatory is presented, and the analysis of results obtained by the parasitic system is discussed. The system, designated SERENDIP, is a real-time microprocessor-controlled spectrum analyzer with algorithms for performing statistical operations and recording those spectra with characteristics presumed to be typical of intelligent rather than astrophysical origin. Programs also exist for the post-acquisition analysis of signal autocorrelation, power spectra, time behavior and positional coordinates, and for a generalized cluster analysis to detect clusters of signal detections. In a recent run of 35 days, the SERENDIP system detected 4000 narrowband spectra exceeding a preset threshold, of which 98% were determined to be of instrumental origin. The remaining class of detections is also believed to be instrumental, although not as well organized as the first signals, and means are currently being sought for eliminating them.

Bowyer, S.↗

Modeling of nonlinear constitutive relations of woven ceramic composites

The linear and nonlinear tensile behavior of SiC/SiC composites is examined. This analysis is based on the observed stress-strain behavior and damage evolution from a series of loading and unloading tensile tests. Stress distribution of the composite with transverse cracks in the transverse yarns is examined, and the nonlinearity of the composite stress-strain relation due to the presence of transverse cracks is predicted by application of a maximum failure strain criterion for the transverse yarn.

Kuo, Wen-Shyong↗

Verification and Validation of Progressive Damage and Failure Analysis Methods for Intralaminar Failure Modes in Thermoplastic Composites

Current progressive damage and failure analysis (PDFA) methods were developed around thermoset material systems and their physical behavior. However, the applicability of these analysis methods has not been evaluated for use in modeling thermoplastic material systems. As part of the Hi-Rate Composite Aircraft Manufacturing (HiCAM) Project sponsored by NASA, intralaminar failure characterization was completed on a thermoplastic material system, AS4D/PEKK-FC, with off-axis tension (OAT) and off-axis compression (OAC) testing. The experiments were able to capture matrix non-linear shear behavior and the failure envelope of the material system. Two PDFA methods, LS-DYNA MAT299 and NASA’s CompDam-DGD, were then employed to simulate individual coupon behavior and simulation results were compared to published verification and validation guidelines from the CMH-17 crashworthiness working group. The results found that the two modeling methods provided suitable representation of material behavior of thermoplastics.

PDFA↗

Verification and Validation of Progressive Damage and Failure Analysis Methods for Intralaminar Failure Modes in Thermoplastic Composites

Current progressive damage and failure analysis (PDFA) methods were developed around thermoset material systems and their physical behavior. However, the applicability of these analysis methods has not been evaluated for use in modeling thermoplastic material systems. As part of the Hi-Rate Composite Aircraft Manufacturing (HiCAM) Project sponsored by NASA, intralaminar failure characterization was completed on a thermoplastic material system, AS4D/PEKK-FC, with off-axis tension (OAT) and off-axis compression (OAC) testing. The experiments were able to capture matrix non-linear shear behavior and the failure envelope of the material system. Two PDFA methods, LS-DYNA MAT299 and NASA’s CompDam-DGD, were then employed to simulate individual coupon behavior and simulation results were compared to published verification and validation guidelines from the CMH-17 crashworthiness working group. The results found that the two modeling methods provided suitable representation of material behavior of thermoplastics.

PDFA↗

SOFE2023 Presentation: "Tritium Safety and Sensitivity Analysis of Tritium Extraction eXperiment (TEX) PbLi Loop Using MELCOR-TMAP"

The efficient extraction of tritium from the breeder blanket (BB) in a fusion reactor is vital for maintaining the tritium economy for a sustainable and self-sufficient fusion power plant. The vacuum permeator (VP) design is one of several promising technology platforms for extracting tritium from the BB with the advantages of being capable of operating continuously at high temperatures with the aim of achieving high tritium extraction efficiencies. The Tritium Extraction eXperiment (TEX), under construction at the Safety and Tritium Applied Research (STAR) Facility at Idaho National Laboratory (INL), is designed to test the viability of VP technology by introducing atomic hydrogen (H, D, and T) from a source permeator (SP) into a forced convection lead lithium eutectic (PbLi) loop and determining the hydrogen extraction rates from the vanadium VP. Presented here is a computational analysis of the hydrogen inventory and permeation behavior in TEX using the hydrogen transport and accident analysis code MELCOR-TMAP developed at INL. The results of a sensitivity analysis based on MELCOR-TMAP simulations of hydrogen extraction efficiencies from the TEX test section using varying PbLi flow rates, hydrogen source rates from the SP, and material property uncertainties are also reported. Operation scenarios for TEX in consideration of the analyses based on results from MELCOR-TMAP are discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗