Search NASA⌕ Search

SEARCH · Search NASA

Results for “CONCENTRATION RATIO”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Understanding geopolymer binder-aggregate interfacial characteristics at molecular level

The interfacial characteristics of geopolymer binder to aggregate composites are poorly understood, especially at molecular level. Herein, molecular models are developed to study, for the first time, the geopolymer-aggregate interface. Chemically, various forms of interfacial bonding are characterized, including Al-O-Si bonding through condensation reactions, NaO and H-bonding. An atomic-level interfacial transition zone (ITZ) is identified, attributed to the concentration of –OH groups. Increasing the Si/Al ratio of geopolymer is found to decrease the ITZ density, but have limited effect on the ITZ width. A heterogeneous diffusion characteristic occurs in geopolymer, due to the weak interfacial interaction. Mechanically, lowering the Si/Al ratio promotes the interfacial strength due to the stronger interfacial interaction and higher cross-linking degree in geopolymer. Under loading the interfacial fracture undergoes three stages: crack propagation, chain bridging (including aluminosilicate and ionic bridging) and breakage. The above atomic-level findings may facilitate a better design of geopolymer concrete in engineering.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Observation of [VCu1–Ini2+VCu1–] Defect Triplets in Cu-Deficient CuInS2

Copper indium disulfide (CuInS2) is a semiconductor with a direct energy band gap of 1.53 eV, an optimal value for highly efficient thin-film solar cells. But it has reached only ~ 11 % power conversion efficiency, far less than the theoretically achievable value of ~ 30 %. The cause of this low performance is not understood. A single crystal grown from 1 mol% Cu-deficient melt was studied, using atomic resolution high-angle annular dark-field (HAADF) scanning transmission electron microscopy (STEM) and electron dispersive spectroscopy (EDS). While the bulk crystal is exactly stoichiometric CuInS2, it contains nanometer-thick, structurally coherent, Cu-deficient interphases that form along rotational twin boundaries in the {112} plane. Transition zones from bulk crystal to interphase are observed, where In is seen to move from its normal site InIn in the chalcopyrite structure to a tetrahedral interstitial site Ini, while Cu remains in its normal CuCu position. Two InIn rows of the bulk crystal merge into one row of Ini, causing excess Ini in the interphase. The concentrations of CuCu and Ini reflect a ratio of Cu vacancies, VCu, to excess Ini of ~ 2. Their relative lattice positions, and the high electrical resistivity of the crystal, suggests that VCu and excess Ini ‘precipitate’ as self-compensating, electrically neutral, [VCu1- Ini2+ VCu1-] defect triplets. This is the first atomic-level observation of the ordered defect that has been invoked as the basic structural modifier in chalcopyrite compound homologs. The interphases introduce an optical gap of 1.47 eV. Electron trapping in band tail states, evident from a photoconductivity exponent of 0.54, is the likely cause of an unusually low electron mobility of 0.1 cm2V-1s-1. The overall result is that making CuInS2 slightly copper-poor inserts nanometer-thick layers of the interphase into the bulk crystal. This study shows that apparently conflicting results of the effect of Cu deficiency on CuInS2 thin-film solar cells may be resolved by analyzing structure and composition at nanometer spatial resolution.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Synthesis of a Hybrid Nanostructure of ZnO-Decorated MoS 2 by Atomic Layer Deposition

We introduce here the synthesis of hybrid nanostructures comprised of ZnO nanocrystals (NCs) decorating nanosheets and nanowires (NWs) of MoS 2 prepared by atomic layer deposition (ALD). The concentration, size, and surface-to-volume ratio of the ZnO NCs can be systematically engineered by controlling both the number of ZnO ALD cycles and the properties of the MoS 2 substrates, which are prepared by sulfurizing ALD MoO 3 . Analysis of the chemical composition combined with electron microscopy and synchrotron X-ray techniques as a function of the number of ZnO ALD cycles, together with the results of quantum chemical calculations, help elucidate the ZnO growth mechanism and its dependence on the properties of the MoS 2 substrate. The defect density and grain size of MoS 2 nanosheets are controlled by the sulfurization temperature of ALD MoO 3 , and the ZnO NCs in turn nucleate selectively at defect sites on MoS 2 surface and enlarge with increasing ALD cycle numbers. At higher ALD cycle numbers, the coalescence of ZnO NCs contributes to an increase in areal coverage and NC size. Furthermore, the geometry of the hybrid structures can be tuned by changing the dimensionality of the MoS 2 , by employing vertical NWs of MoS 2 as the substrate for ALD ZnO NCs, which in turn leads to improvement of the relevant surface-to-volume ratio. Such materials are expected to find use in newly expanded applications, especially those such as sensors or photo-devices based on a p-n heterojunction which relies on coupling transition metal dichalcogenides (TMDCs) with NCs.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Ultra-Low Viscosity and High Magnetic Susceptibility Magnetic Ionic Liquids Featuring Functionalized Diglycolic Acid Ester Rare-Earth and Transition Metal Chelates

Magnetic ionic liquids (MILs) comprise a subcategory of ionic liquids (ILs) and contain a paramagnetic metal center allowing them to be readily manipulated by an external magnetic field. While MILs are popularly employed as solvents in catalysis, separations, and organic synthesis, most low viscosity combinations possess a hydrophilic character that limits their use in aqueous matrices. To date, no study has reported the synthesis and characterization of hydrophobic MILs with viscosities similar to those of hydrophilic MILs and organic solvents while simultaneously exhibiting enhanced magnetic and thermal properties. In this study, diglycolic acid esters are employed as ligands to chelate with paramagnetic metals to produce cations that are paired with metal chelates composed of hexafluoroacetylacetonate ligands to form MILs incorporating multiple metal centers in the cation and anion. Viscosity values below 31.6 cP were obtained for these solvents, the lowest ever reported for hydrophobic MILs. Solubilities in nonpolar solvents such as benzene were observed to be as high as 50% (w/v) MIL-to-solvent ratio while being insoluble in water at concentrations as low as 0.01% (w/v). Effective paramagnetic moment values for these solvents ranged from 5.33 to 15.56 Bohr magnetons (μB), with mixed metal MILs containing multiple lanthanides in the anion generally offering higher magnetic susceptibilities. MILs composed of ligands containing octyl substituents were found to possess thermal stabilities up to 190 °C. The synthetic strategies explored in this study exploit the highly tunable nature of the employed cation and anion pairs to design versatile ultra-low viscosity magnetoactive solvents that possess tremendous potential and applicability in liquid–liquid separation systems, catalysis, and microfluidics where the mechanical movement of the solvent can be easily facilitated using electromagnets.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Reversible Emulsions from Polyoxometalate–Polymer: A Robust Strategy to Cyclic Emulsion Catalysis and High-Internal-Phase Emulsion Materials

Reversible Pickering emulsions, achieved by switchable, interfacially active colloidal particles, that enable on-demand emulsification/demulsification or phase inversion, hold substantial promise for biphasic catalysis, emulsion polymerization, cutting fluids, and crude oil pipeline transportation. However, particles with such a responsive behavior usually require complex chemical syntheses and surface modifications, limiting their extensive use. Herein, we report a simple route to generate emulsions that can be controlled and reversibly undergo phase inversion. The emulsions are prepared and stabilized by the interfacial assembly of polyoxometalate (POM)–polymer, where their electrostatic interaction at the interface is dynamic. The wettability of the POMs that dictates the emulsion type can be readily regulated by tuning the number of polymer chains bound to POMs, which, in turn, can be controlled by varying the concentrations of both components and the water/oil ratio. In addition, the number of polymer chains anchored to the POMs can be varied by controlling the number of negative charges on the POMs through an in situ redox reaction. As such, a reversible inversion of the emulsions can be triggered by switching between exposure to ultraviolet light and the introduction of oxygen. Combining the functions of POM itself, a cyclic interfacial catalysis system was realized. Inversion of the emulsion also affords a pathway to high-internal-phase emulsions. Finally, the diversity of the POMs, the polymers, and the responsive switching groups open numerous new, simple strategies for designing a wide range of responsive soft matter for cargo loading, controlled release, and delivery in biomedical and engineering applications without time-consuming particle syntheses.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Rapid Mineral Precipitation During Shear Fracturing of Carbonate-Rich Shales

Target subsurface reservoirs for emerging low-carbon energy technologies and geologic carbon sequestration typically have low permeability and thus rely heavily on fluid transport through natural and induced fracture networks. Sustainable development of these systems requires deeper understanding of how geochemically mediated deformation impacts fracture microstructure and permeability evolution, particularly with respect to geochemical reactions between pore fluids and the host rock. Here, a series of triaxial direct shear experiments was designed to evaluate how fractures generated at subsurface conditions respond to penetration of reactive fluids with a focus on the role of mineral precipitation. Calcite-rich shale cores were directly sheared under 3.5 MPa confining pressure using BaCl 2 -rich solutions as a working fluid. Experiments were conducted within an X-ray computed tomography (xCT) scanner to capture 4-D evolution of fracture geometry and precipitate growth. Three shear tests evidenced nonuniform precipitation of barium carbonates (BaCO 3 ) along through-going fractures, where the extent of precipitation increased with increasing calcite content. Precipitates were strongly localized within fracture networks due to mineral, geochemical, and structural heterogeneities and generally concentrated in smaller apertures where rock:water ratios were highest. The combination of elevated fluid saturation and reactive surface area created in freshly activated fractures drove near-immediate mineral precipitation that led to an 80% permeability reduction and significant flow obstruction in the most reactive core. While most previous studies have focused on mixing-induced precipitation, this work demonstrates that fluid–rock interactions can trigger precipitation-induced permeability alterations that can initiate or mitigate risks associated with subsurface energy systems.

58 GEOSCIENCES↗
DOE OSTI2024

Rheology of bi-disperse dense fiber suspensions

While significant progress has been made in the modeling and simulation of uniform fiber suspensions, no existing model has been validated for industrially-relevant concentrated suspensions containing fibers of multiple aspect ratios. In the present work, we investigate bi-disperse suspensions with two fiber populations in varying aspect ratios in a steady shear flow using direct numerical simulations. Moreover, we measure the suspension viscosity by creating a controlled length bidispersity for nylon fibers suspended in a Newtonian fluid. Here the results showed good agreement between the experimentally measured and numerically predicted viscosity for bi-disperse suspensions. The ratio between the aspect ratio of large to small fibers (size ratio) and the volume fraction of large fibers (composition) in bi-disperse systems strongly affected the rheological behavior of the suspension. The increment of relative viscosity associated with size ratio and composition can be explained by the decrease in the maximum flowable limit or jamming volume fraction. Moreover, the relative viscosity of bi-disperse suspensions collapses, when plotted against the reduced volume fraction, demonstrating the controlling influence of the jamming fraction in bi-disperse fiber suspensions.

42 ENGINEERING↗
DOE OSTI2025

Detection of Br and I as atomic anions using liquid sampling – atmospheric pressure glow discharge/Orbitrap mass spectrometry

The quantification and determination of halogen isotope composition is essential in many fields including geochemistry and nuclear forensics. Detection of the halogen elements is commonly attempted with inductively coupled plasma mass spectrometry (ICP-MS) however, there are multiple challenges faced. Most significantly this includes very poor ionization efficiency and the potential for isobaric interferences from either matrix or plasma species. Thus, sensitivity and accuracy are often limiting issues. Here a liquid sampling-atmospheric pressure glow discharge (LS-APGD) ionization source is coupled with an ultrahigh resolution Orbitrap MS to perform halogen detection of bromine and iodine as initial analytes. This facilitates simple and sensitive detection of these elements as atomic anions from simple aqueous salt solutions. Collision-induced dissociation (CID) and higher-energy collisional dissociation (HCD) energies were optimized to produce the maximum response of Br − and I − . The LS-APGD conditions were optimized using a design of experiments (DOE) approach for Br − and I − concurrently. Response curves for Br − and I − solutions determined limit of detection (LOD) values of 50 pg and 5 pg, respectively, in 20 μL aliquots. The curves indicated response factors of 0.67 for 79 Br − and 0.90 for 127 I − . Br isotope ratios were determined with precision between 0.7 and 7.3% RSD, with the isotope ratios determined with precision 0.8% RSD at concentrations above the limit of quantification. Preliminary tests were conducted to evaluate the effect of different cations (Na + , K + , and Mg 2+ ) on Br − responses, with no discernible impacts observed on the halogen signal responses. This study demonstrates the potential use of the LS-APGD-Orbitrap-MS for the detection of multiple halogens while avoiding interferences, minimizing sample preparation, and overcoming ionization barriers.

Lang, Dehlia A. [Clemson University, SC (United St↗
DOE OSTI2026

Transgenic Mixed‐Linkage‐Glucan Enhancement Affects Root Characteristics and Decomposition in Soils of Contrasting Vegetation History

ABSTRACT Development of transgenic bioenergy sorghum [ Sorghum bicolor (L.) Moench] with increased contents of mixed‐linkage (1,3;1,4)‐β‐glucan (MLG) is an important step towards enhancing quality of bioenergy feedstocks. Since MLG‐enhancement leads to greater biomass digestibility, our overarching hypothesis is that root residues of MLG‐enhanced plants may be more readily decomposed in the soil, potentially creating new opportunities for optimizing soil carbon (C) sequestration, nutrient cycling, and overall agricultural sustainability. The study examined morphological, chemical, and enzymatic characteristics of fine and coarse roots of four bioenergy sorghum genotypes. Then, we incubated the roots within soils with contrasting vegetation histories while measuring C mineralization, microbial biomass C (MBC), and activity of hydrolytic enzymes and calculating vector length and vector angle enzymatic stoichiometry parameters. The results indicated that MLG‐enhancing transformations increased root total nitrogen (N) contents, decreased C/N ratios, and were associated with higher MLG concentrations in fine than in coarse roots. Incubations with transgenic roots led to 16%–38% higher MBC and 19%–41% lower microbial metabolic quotient (qCO 2 ). While enzyme activity differed markedly among the studied genotypes, it did not directly respond to MLG levels in root tissues. The increase in MBC without concurrent increases in C mineralization or hydrolytic enzyme activities in transgenic genotypes suggests that MLG enhancement promoted microbial anabolic retention of root‐derived C rather than stimulating catabolic decomposition. Enzymatic vector results indicated that these parameters reflect a variety of drivers behind microbial enzyme production, including availability of specific substrates, such as MLG here, and/or deficiency in specific nutrients, such as phosphorus (P). The study confirms the positive impacts from the roots of engineered MLG‐enhanced bioenergy plants on soil microbial activity and highlights the interactive influences on the MLG‐enhancement effects from root size and inherent soil properties.

Mahmoodabadi, Majid [Department of Plant, Soil, an↗
DOE OSTI2023

Biomass Gasification for Chemicals Production Using Chemical Looping Techniques (Final Report)

The Ohio State University (OSU) is investigating the Biomass to Syngas (BTS) chemical looping technology to produce syngas for chemical production applications from biomass under US Department of Energy (DOE) Award #DE-EE0007530. The BTS process aligns with the programmatic area of interest of “Conversion, via biological, thermal, catalytic or chemical means, of acceptable feedstocks into advanced biofuels and/or biobased products including intermediate and end-use products”. Compared to conventional biomass gasification processes, the BTS process eliminates the need for air separation units and tar reforming reactors, which leads to energy efficiency improvement and capital cost reduction. The overall objective is to ascertain the potential of biomass gasification based on the chemical looping technique through mitigation of the possible techno-economic challenges in the steps of scale up for commercialization. The scope of work consists of 1) designing, constructing and operating a 10 kWth commercially scalable sub-pilot BTS system and; 2) completing a comprehensive techno-economic analysis (TEA) of the BTS process using methanol production as an example. Over the course of the project, the project team completed the design, fabrication, and operation of a 10 kWth sub-pilot scale test unit for the BTS process. Corn cob and wood pellets were successfully tested in the unit for high purity syngas generation in extended test campaigns that totals over 200 hours. Syngas purity (H2 and CO) of >70% was achieved with a CH 4 concentration of <6%. The H 2 /CO ratio was greater than 1.8. A comprehensive techno-economic analysis was performed to compare the BTS process and a reference indirectly heated gasification process for methanol synthesis. The result, updated with experimental results for BTS process performance, shows a methanol required selling price (MSP) of $\$ $1.15/gal, compared to $1.28/gal for the reference case.

08 HYDROGEN↗
NASA NTRS1974

Venus cloud properties: Infrared opacity and mass mixing ratio

By using the Mariner 5 temperature profile and a homogeneous cloud model, and assuming that CO2 and cloud particles are the only opacity sources, the wavelength dependence of the Venus cloud opacity is inferred from the infrared spectrum of the planet between 450 and 1250/cm. Justification for applying the homogeneous cloud model is found in the fact that numerous polarization and infrared data are mutually consistent within the framework of such a model; on the other hand, dense cloud models are not satisfactory. Volume extinction coefficients varying from 0.000005 to 0.000015/cm depending on the wavelength, are determined at the tropopause level of 6110 km. By using all available data, a cloud mass mixing ratio of approximately 0.000005 and a particle concentration of about 900 particles per cu cm at this level are also inferred. The derived cloud opacity compares favorably with that expected for a haze of droplets of a 75% aqueous solution of sulfuric acid.

Samuelson, R. E.↗
NASA NTRS1975

Venus cloud properties - Infrared opacity and mass mixing ratio

By using the Mariner 5 temperature profile and a homogeneous cloud model, and assuming that CO2 and cloud particles are the only opacity sources, the wavelength dependence of the Venus cloud opacity is inferred from the infrared spectrum of the planet between 450 and 1250 per cm. Volume extinction coefficients varying from 0.000005 to 0.000015 per cm, depending on the wavelength, are determined at the tropopause level of 6110 km. By using all available data, a cloud mass mixing ratio of approximately 0.000005 and a particle concentration of about 900 particles per cu cm at this level are also inferred. The derived cloud opacity compares favorably with that expected for a haze of droplets of a 75% aqueous solution of sulfuric acid.

Samuelson, R. E.↗
NASA NTRS1976

A Monte-Carlo simulation of galactic cosmic ray effects in the lunar regolith

A Monte-Carlo soil mixing computer code was used to evaluate isotopic effects induced by galactic cosmic rays in samples on the top surface of the lunar regolith and in lunar core tubes. For surface samples, good agreement was found between theoretical predictions of Ne-21 concentrations, neutron fluences, and Xe-131/Xe-126 ratios, and the corresponding observations.

Langevin, Y.↗
NASA NTRS1978

Germane in the atmosphere of Jupiter

Germane, GeH4, is a tetrahedral molecule like methane. The nu 3 fundamental mode of GeH4 falls in the middle of the 5-micrometer Jupiter window. Jupiter observations were made in December 1975 during three flights with the 0.9-m telescope of the Kuiper Airborne Observatory. The spectrometer is a rapid-scanning Michelson interferometer having InSb detectors at each of the two outputs. The germane identification procedure is based on a comparison of the obtained Jupiter spectrum with that of laboratory germane. It appears that the detection of GeH4 in Jupiter's atmosphere with a mixing ratio of 0.6 ppb is the smallest concentration of a trace constituent yet detected in a nonterrestrial planetary atmosphere. It is pointed out that a strict interpretation of thermochemical equilibrium predictions for the spectral line forming regions of Jupiter's atmosphere does not explain the observation of GeH4.

Fink, U.↗
NASA NTRS1977

Lead isotope studies of mare basalt 70017

Uranium, thorium, and isotopic lead data for components of basalt 70017 are reported, and it is found that the whole rock, pyroxene, and ilmenite points in a concordia diagram plot along a chord intersecting the curve at 3.7 and 4.33 eons. The plagioclase data do not seem to lie on this line. The data for 70017 appear to plot along a distinctly different chord in a concordia diagram than do the data for 75055 and 75035, two other Apollo 17 mare basalts. The lead data are in accord with Sm-Nd results. A 3.7 eon crystallization age for 70017 would be consistent with the same kind of parentless lead that is indicated by previous studies of soils and soil breccias from stations at Taurus-Littrow. The Th/U ratio in ilmenite is 2.2, and the concentrations of these two elements are approximately twice those in pyroxene.

Mattinson, J. M.↗
NASA NTRS1980

Apparatus for measuring semiconductor device resistance

A test structure is described for enabling the accurate measurement of the resistance characteristics of a semiconductor material and includes one or more pairs of electrical terminals disposed on the surface of the material to enable measurements of the resistance encountered by currents passed between the terminals. A pair of terminals includes a first terminal extending in a closed path, such as a circle, around a second terminal, so that all currents flowing between the terminals flow along a region of known width and length. Two or more pairs of concentric terminals can be utilized, wherein the ratio of radii of each pair of terminals is the same as the ratio for all other pairs of terminals, to facilitate the calculation of the contact resistance between each terminal and the semiconductor surface, as well as the calculation of the resistance of the semiconductor material apart from the effect of the terminal to semiconductor contact resistances.

Matzen, W. J.↗
NASA NTRS1980

Adsorption interference in mixtures of trace contaminants flowing through activated carbon adsorber beds

Adsorption interference in binary and ternary mixtures of trace contaminants in a helium carrier gas flowing through activated carbon adsorber beds are studied. The isothermal transmission, which is the ratio of the outlet to the inlet concentration, of each component is measured. Interference between co-adsorbing gases occurs when the components are adsorbed strongly. Displacement of one component by another is manifested by a transmission greater than unity for the displaced component over some range of eluted volume. Interference is evidenced not only by a reduction of the adsorption capacity of each component in the mixture in comparison with the value obtained in a single-component experiment, but also by a change in the slope of the transmission curve of each component experiment.

Madey, R.↗