Search NASA⌕ Search

SEARCH · Search NASA

Results for “Compressive Strength”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

Effect of Deformation Temperature on the Microstructure and Mechanical Properties of High-Strength Low-Alloy Steel During Hot Compression

The microstructure and mechanical properties of high-strength low-alloy steel were investigated at deformation temperatures of 800-1100 °C and strain rates of 0.1-10 s{sup −1} using an MMS-200 thermal mechanical simulator. The results indicated that the increased deformation processes observed between the starting and finishing temperatures during hot compression testing caused a polygonal ferrite transformation in the material. The polygonal ferrite grain sizes increased with increasing transformation temperatures and gradually grew larger at higher deformation temperatures. Widmanstätten ferrite and acicular ferrite were also formed at high temperatures from 1000-1100 °C, which accordingly led to an increase in Vickers microhardness. In addition, the flow stress in the material increased with an increase in the strain and a decrease in the deformation temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Dynamic Strength of Iron at High Pressures and Strain Rates

Accurate modeling of meteorite impacts, and deformation of planetary cores require characterization of the flow strength and in-elasticity of iron in its different phases. In this letter, we investigate the flow strength of both the ambient α-phase and high-pressure ϵ-phase of iron at strain-rates of 1 × 10 5 s –1 and pressures up to 42 GPa using high pressure - pressure shear plate impact experiments. We report the strength of the ϵ-iron to be significantly higher than α-phase but consequently one order smaller than the previously reported dynamic strength at high pressures. As a result, the complete stress-strain response of the ϵ-phase is reported for the first time.

36 MATERIALS SCIENCE↗
NASA NTRS2024

On the Effectiveness of Using Woven Outer Plies to Suppress Hole Drilling Face Sheet Damage in Honeycomb Sandwich Structure

A payload adaptor fitting (PAF) structure has been manufactured at NASA’s Marshall Space Flight Center (MSFC). The PAF structure is essentially a large cone made of carbon/epoxy sandwich structure. The PAF structure contains numerous (about 1000) holes at the top and bottom to secure the carbon/epoxy structure in aluminum rings with bolts. In an effort to obtain higher quality holes, both sides of the PAF structure are covered with an additional, non-structural, ply of woven carbon/epoxy placed at ±45⁰ to the vertical direction. This study evaluated the quality of the holes on sandwich structure both with and without the outer woven carbon/epoxy plies via open hole compression (OHC) strength testing. Results showed a 14% increase in strength of the cloth covered sandwich structure, which did not surpass the 18% added weight due to the outer woven plies.

sacrificial plies↗
DOE OSTI2021

Dynamic Strength of Copper at High Pressures Using Pressure Shear Plate Experiments

Measurement of strength at high pressures is critical to understanding the behavior of materials subjected to extreme loading conditions. Recent developments have extended the pressure shear plate impact (PSPI) technique to the high-pressure regime. Such experiments provide a unique opportunity to extract the complete stress-strain behavior of materials at relatively high pressures. The modified technique includes a new fiber-optic heterodyne transverse velocity interferometer system and new analysis methods to account for the inelastic response of the anvil plates. In this study, PSPI experiments are conducted on oxygen-free high conductivity (OFHC) copper at pressures ranging from 10 to 43 GPa and at strain rates of ~10 5 s -1 . Complete stress-strain curves of copper are obtained using a hybrid methodology that relies on numerical simulations and particle velocity records gathered in these experiments. Experiments are conducted at similar pressures and strain rates using two types of anvils that undergo different levels of plastic strains: tool steel and tungsten carbide, to check the robustness of the hybrid method. The behavior of copper at these high pressures and strain rates is compared with previous literature data, and the effect of pressure and strain rate on the strength behavior of copper are discussed. Here, it was observed that the rate of change in yield strength change in pressure was 2.5 times the rate of change of shear modulus with pressure. The strength models that predict the response of copper at these extreme conditions are also examined and validated.

36 MATERIALS SCIENCE↗
NASA NTRS2010

Use of Nanofibers to Strengthen Hydrogels of Silica, Other Oxides, and Aerogels

Research has shown that including up to 5 percent w/w carbon nanofibers in a silica backbone of polymer crosslinked aerogels improves its strength, tripling compressive modulus and increasing tensile stress-at-break five-fold with no increase in density or decrease in porosity. In addition, the initial silica hydrogels, which are produced as a first step in manufacturing the aerogels, can be quite fragile and difficult to handle before cross-linking. The addition of the carbon nanofiber also improves the strength of the initial hydrogels before cross-linking, improving the manufacturing process. This can also be extended to other oxide aerogels, such as alumina or aluminosilicates, and other nanofiber types, such as silicon carbide.

Meador, Mary Ann B.↗
NASA NTRS1993

Experiments on the enhancement of compressible mixing via streamwise vorticity. II - Vortex strength assessment and seed particle dynamics

The effect of streamwise vorticity on compressible axisymmetric mixing layers is examined using vortex strength assessment and seed particle dynamics analysis. Experimental results indicate that the particles faithfully represent the dynamics of the turbulent swirling flow. A comparison of the previously determined mixing layer growth rates with the present vortex strength data reveals that the increase of turbulent mixing up to 60 percent scales with the degree of swirl. The mixing enhancement appears to be independent of the compressibility level of the mixing layer.

Naughton, J. W.↗
NASA NTRS1939

Local instability of centrally loaded columns of channel section and Z-section

Charts are presented for the coefficients in formulas for the critical compressive stress at which cross-sectional distortion begins in a thin-wall member with either a channel section or a Z-section with identical flanges. The energy method of Timoshenko was used in the theoretical calculations required for the construction of the charts. The deflection equations were carefully selected to give good accuracy. The calculation of the critical compressive stress at stresses beyond the elastic range is briefly discussed. In order to demonstrate the use of the formulas and the charts in engineering calculations, two illustrative problems are included.

ELASTICITY↗
NASA NTRS2011

A Damage Tolerance Comparison of Composite Hat-Stiffened and Honeycomb Sandwich Structure for Launch Vehicle Interstage Applications

In this study, a direct comparison of the compression-after-impact (CAI) strength of impact-damaged, hat-stiffened and honeycomb sandwich structure for launch vehicle use was made. The specimens used consisted of small substructure designed to carry a line load of approx..3,000 lb/in. Damage was inflicted upon the specimens via drop weight impact. Infrared thermography was used to examine the extent of planar damage in the specimens. The specimens were prepared for compression testing to obtain residual compression strength versus damage severity curves. Results show that when weight of the structure is factored in, both types of structure had about the same CAI strength for a given damage level. The main difference was that the hat-stiffened specimens exhibited a multiphase failure whereas the honeycomb sandwich structure failed catastrophically.

Nettles, A. T.↗
DOE OSTI2024

Multiscale Richtmyer-Meshkov instability experiments to isolate the strain rate dependence of strength

Theoretical analysis of Richtmyer-Meshkov instability (RMI) experiments for solid strength shows that the strain rate for a given shock should be inversely proportional to the length scale of the sine wave perturbations when η 0 k , the nondimensional amplitude to wavelength ratio, is held fixed. To isolate the effect of strain rate on strength, free-surface RMI specimens of annealed copper were prepared with three perturbation regions with the same η 0 k but different length scales, characterized by the wavelength λ varying by a factor of 4.9 from 65 to 130 to 320 µ m . Three such targets with different fixed η 0 k ′ s were impacted to a shock pressure of 25 GPa, and the instability evolution was measured with photon Doppler velocimetry. Strengths estimated by comparing hydrocode simulation to the data increased from 700 to 1200 MPa as λ decreased. The different η 0 k targets exercised increasing amounts of plastic strain yet showed no evidence of strain hardening. Physical regime sensitivity analysis determined that for 320 − 65 µ m wavelength perturbations, the effective strain rates increased from 8.7 × 10 6 to 3.3 × 10 7 s − 1 , a factor of 3.8. Thus, the predicted strain rate scaling was mostly achieved but slightly suppressed by increased strength at higher rates. The RMI strength estimates were plotted against constitutive testing data on copper from the literature to show striking evidence of the strength upturn at higher strain rates. Published by the American Physical Society 2024

36 MATERIALS SCIENCE↗
NASA NTRS1995

Directional Solidification and Mechanical Properties of NiAl-NiAlTa Alloys

Directional solidification of eutectic alloys is a promising technique for producing in-situ composite materials exhibiting a balance of properties. Consequently, the microstructure, creep strength and fracture toughness of directionally solidified NiAl-NiAlTa alloys were investigated. Directional solidification was performed by containerless processing techniques to minimize alloy contamination. The eutectic composition was found to be NiAl-15.5 at% Ta and well-aligned microstructures were produced at this composition. A near-eutectic alloy of NiAl-14.5Ta was also investigated. Directional solidification of the near-eutectic composition resulted in microstructures consisting of NiAl dendrites surrounded by aligned eutectic regions. The off-eutectic alloy exhibited promising compressive creep strengths compared to other NiAl-based intermetallics, while preliminary testing indicated that the eutectic alloy was competitive with Ni-base single crystal superalloys. The room temperature toughness of these two-phase alloys was similar to that of polycrystalline NiAl even with the presence of the brittle Laves phase NiAlTa.

Johnson, D. R.↗
DOE OSTI2019

Estimates of Ta strength at ultrahigh pressures and strain rates using thin-film graded-density impactors

In this paper, we present results from an experimental technique used to estimate the strength of Ta at extreme pressures (150 GPa) and strain rates (10 7 s -1 ). A graded-density impactor (GDI) was fabricated using sputter deposition to produce an approximately 40-μm-thick film containing alternating layers of Al and Cu. The thicknesses of the respective layers are adjusted to give an effective density gradient through the film. The GDIs were launched with a 2-stage light gas gun, and shock-ramp-release velocity profiles were measured over timescales of ~10 ns. Results are presented for the direct impact of the film onto LiF windows, which allows for a dynamic characterization of the GDI, as well as from impact onto thin (~40μm) sputtered Ta samples backed by a LiF window. The measurements were coupled with mesoscale numerical simulations to infer the strength of Ta, and the results agree well with other high-pressure platforms, particularly when strain-rate, microstructural, and thermodynamic-path differences are considered.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

Review of supplementary cementitious materials with implications for age-dependent concrete properties affecting precast concrete

Here, this paper presents a comprehensive review of existing research examining the effects of supplementary cementitious materials on age-dependent concrete properties with the most profound implications for precast concrete production. The review covers the physical and chemical properties of selected types of supplementary cementitious materials, concrete mixture proportions, concrete curing methods, testing procedures, and test results related to the fresh properties and strengths of a range of concrete mixtures. Although the use of supplementary cementitious materials in precast concrete products is common, the detailed information provided in this paper may facilitate more widespread use of these materials to enhance concrete properties and comply with sustainability initiatives.

20 FOSSIL-FUELED POWER PLANTS↗
NASA NTRS1989

Parameters of tensile strength, elongation, and tenacity of 70mm IIaO spectroscopic film

The 70mm IIaO spectroscopic film was tested to determine its tensile strength, elongation, and breaking strength, using an Instron (strength and compression) 4201 Test Instrument. These data provide information leading to the upper and lower limits of the above parameters for 70mm IIaO spectroscopic film. This film will be developed by a commercial developing machine after the Ultraviolet Telescope Space Shuttle Mission returns to the Earth in the early 1990's; thus, it is necessary to understand these force parameters. Several test strips of approximately 200mm in length were used. The results indicate that when a stress load of 100 kg was applied, the film elongated approximately 1.06mm and the break strength was 19.45 kilograms.

Hammond, Ernest C., Jr.↗
NASA NTRS2006

The Compressive Behavior of Isocyanate-crosslinked Silica Aerogel at High Strain Rates

Aerogels are low-density, highly nano-porous materials. Their engineering applications are limited due to their brittleness and hydrophilicity. Recently, a strong lightweight crosslinked silica aerogel has been developed by encapsulating the skeletal framework of amine-modified silica aerogels with polyureas derived by isocyanate. The mesoporous structure of the underlying silica framework is preserved through conformal polymer coating, and the thermal conductivity remains low. Characterization has been conducted on the thermal, physical properties and the mechanical properties under quasi-static loading conditions. In this paper, we present results on the dynamic compressive behavior of the crosslinked silica aerogel (CSA) using a split Hopkinson pressure bar (SHPB). A new tubing pulse shaper was employed to help reach the dynamic stress equilibrium and constant strain rate. The stress-strain relationship was determined at high strain rates within 114-4386/s. The effects of strain rate, density, specimen thickness and water absorption on the dynamic behavior of the CSA were investigated through a series of dynamic experiments. The Young's moduli (or 0.2% offset compressive yield strengths) at a strain rate approx.350/s were determined as 10.96/2.08, 159.5/6.75, 192.2/7.68, 304.6/11.46, 407.0/20.91 and 640.5/30.47 MPa for CSA with densities 0.205, 0.454, 0.492, 0.551,0.628 and 0.731 g/cu cm, respectively. The deformation and failure behaviors of a native silica aerogel with density (0.472 g/cu cm ), approximately the same as a typical CSA sample were observed with a high speed digital camera. Digital image correlation technique was used to determine the surface strains through a series of images acquired using high speed photography. The relative uniform axial deformation indicated that localized compaction did not occur at a compressive strain level of approx.17%, suggesting most likely failure mechanism at high strain rate to be different from that under quasi-static loading condition. The Poisson s ratio was determined to be 0.162 in nonlinear regime under high strain rates. CSA samples failed generally by splitting, but were much more ductile than native silica aerogels.

Luo, H.↗