Search NASA⌕ Search

SEARCH · Search NASA

Results for “DECELERATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42

Atmospheric environment during maneuvering descent from Martian orbit

This paper presents an analysis of the atmospheric maneuvering capability of a vehicle designated to land on the Martian surface, together with an analysis of the entry environment encountered by the vehicle. A maximum lift/drag ratio of 2.3 was used for all trajectory calculations. The maximum achievable lateral ranges varied from about 3400 km to 2500 km for entry velocities of 5 km/s (from a highly elliptical Martian orbit) and 3.5 km/s (from a low-altitude lower-speed orbit), respectively. It is shown that the peak decelerations are an order of magnitude higher for the 5-km/s entries than for the 3.5-km/s entries. The vehicle entering at 3.5 km/s along a gliding trajectory encountered a much more benign atmospheric environment. In addition, the glider's peak deceleration was found to be only about 0.7 earth g, making the shallow flight path ideal for manned vehicles whose crews might be physically weakened by the long voyage to Mars.

Tauber, Michael E.↗

Flaring arches. II - Events in the arch system of 6/7 November, 1980

A characterization is developed for the 57,000-km long arch-shaped coronal structure of November 6, 1980, which became the site, first, of 13 quasi-periodic X-ray brightenings, and then of a series of 17 flaring arches. A comparison of H-alpha, O V, and X-ray data for the SB arch has qualitatively confirmed that a hot conduction front producing X-rays in the least dense plasma is first present, and is followed by a decelerating, denser plasma bulk in O V, with an eventual, still-further-decelerating very dense plasma becoming visible in H-alpha emission.

Svestka, Zdenek↗

Earth atmospheric entry studies for manned Mars missions

Decelerations, heating rates, and total heat loads encountered when returning from Mars to earth at entry speeds of 12 km/sec to 16 km/sec are studied. For entry at 14 km/sec, it is found that a lift/drag ratio (L/D) of 0.5 is required to provide a guidance corridor margin near 1 deg for the specified deceleration limit of 5 g. For a blunted, raked cone with an L/D = 0.5, the peak heating rate near the aft end of the forebody varies from 0.14 to 0.23 kW/sq cm for laminar flow. If ablation triggers boundary layer transition, the peak heating can rise to 0.5 or up to 0.72 kW/sq cm. All heating rates are sufficiently high to make ablative heat shields necessary.

Tauber, M. E.↗

Aerodynamic requirements of a manned Mars aerobraking transfer vehicle

In this investigation, entry corridor analyses are performed to identify the aerodynamic requirements of a manned Mars aerobraking transfer vehicle. The major emphasis is on identifying the required aerobrake hypersonic L/D to insure a successful aerocapture. Aerobraking entry requirements are also imposed on a set of interplanetary mission opportunities to demonstrate their effect on mission flexibility. Based on the requirements of a 1 deg corridor width, deceleration into a parking orbit witn an apoapsis altitude of 32,972 km, and a 5-g deceleration limit, a manned Mars aerobrake characterized by an L/D of at least 1.5 is required for entry velocities as high as 10.0 km/sec. Limiting the Mars entry velocity to values below 8.5 km/sec is shown to induce a minor restriction on mission flexibility while alleviating aerothermodynamic and vehicle packaging concerns; hence, Mars entry velocities in the range of 6.0-8.5 km/sec are suggested, and a manned Mars aerobrake characterized by an L/D between 0.3 and 0.5 is recommended.

Braun, Robert D.↗

Evolution of a superbubble blastwave in a magnetized medium

Researchers investigate the effects of interstellar magnetic fields on the evolution and structure of interstellar superbubbles, using both analytic and numerical magnetohydrodynamic (MHD) calculations. These cavities of hot gas, surrounded by shells of cold dense material preceded by a shock wave result from the combined action of stellar winds and supernova explosions in OB associations. If the medium in which a superbubble goes off is homogeneous and unmagnetized, the blast wave expands isotropically. As the interstellar gas flows through the shock, it cools significantly and gets strongly compressed such that thermal pressure remains approximately equal to ram pressure. Hence, the swept up material is confined to a very thin shell. However, if the ambient medium is permeated by a uniform magnetic field B sub o approx. 3 mu G (typical value for the interstellar matter (ISM)), the configuration loses its spherical symmetry, and, due to magnetic pressure, the shell of swept up material does not remain thin. Researchers found the following qualitative differences: (1) Except in the immediate vicinity of the magnetic poles, the shell is supported by magnetic pressure. (2) The refraction of field lines at the shock and the thermal pressure gradient along the shell both contribute to accelerating the gas toward the equator. The resulting mass flux considerably decreases the column density at the magnetic poles. (3) Away from the poles, magnetic tension in the shell causes the field lines (particularly the inner boundary) to elongate in the direction of B sub o. In contrast, the shock wave radius increases with increasing theta. (4) The reduced inertia of a parcel in the polar neighborhood makes it easier to decelerate, and accounts for the dimple which appears at the poles in numerical simulations. This dimple also results from the necessity to call on intermediate shocks in order to insure a smooth transition between a purely thermal shock at the poles and a magnetic shock in the rest of the shell. (5) The shock wave propagates faster than in the absence of magnetic field, except near the poles where the reduced mass of the shell allows it to be more efficiently decelerated.

Ferriere, Katia M.↗

A predictor-corrector guidance algorithm for use in high-energy aerobraking system studies

A three-degree-of-freedom predictor-corrector guidance algorithm has been developed specifically for use in high-energy aerobraking performance evaluations. The present study reports on both the development and capabilities of this guidance algorithm to the design of manned Mars aero-braking vehicles. Atmospheric simulations are performed to demonstrate the applicability of this algorithm and to evaluate the effect of atmospheric uncertainties upon the mission requirements. The off-nominal conditions simulated result from atmospheric density and aerodynamic characteristic mispredictions. The guidance algorithm is also used to provide relief from the high deceleration levels typically encountered in a high-energy aerobraking mission profile. Through this analysis, bank-angle modulation is shown to be an effective means of providing deceleration relief. Furthermore, the capability of the guidance algorithm to manage off-nominal vehicle aerodynamic and atmospheric density variations is demonstrated.

Braun, Robert D.↗

The effect of viscosity on steady transonic flow with a nodal solution topology

The effect of viscosity on a steady, transonic flow for which the inviscid limit has a nodal solution topology near the critical point is investigated. For the accelerating case, viscous solutions tend to repel each other, so that a very delicate choice of initial conditions is required to prevent them from diverging. Only the two critical solutions extend to arbitrarily large distances into both the subsonic and supersonic flows. For the decelerating case, the solutions tend to attract, and so an entire two-parameter family of solutions now extends over large distances. The general effect of viscosity on the solution degeneracy of a nodal topology is thus to reduce or limit it for the accelerating case and to enhance it for the decelerating case. The astrophysical implications of these findings are addressed.

Owocki, Stanley P.↗

Ablation of silicate particles in high-speed continuum and transition flow with application to the collection of interplanetary dust particles

The ablative deceleration of spheres in the continuum and slip regimes is studied using spherical 7.1-micron-diam soda-lime glass particles launched from vacuum at about 4500 m/sec speed through a 13-micron-thick plastic film into a capture chamber containing Xe at 0.1 or 0.2 atm pressure and 295 K temperature. The results of SEM examinations of the collected ablated particles showed that the ratio of the ablated-particle radius (Rf) to the initial radius (R0) increased with gas pressure (from Rf/R0 about 0.67 at 0.1 atm, to about 0.88 at 0.2 atm). A model was developed to describe the ablation and deceleration of spheres in high-speed continuum and slip flow. The pressure dependence predicted by the model agreed with experimental results.

Rulison, Aaron J.↗

Modeling the effects of fast shocks on solar winds ions

Observations show that, when alpha particles and other minor ions in the solar wind plasma encounter fast shocks, they are heated more than protons and their bulk motion is decelerated less than protons. These effects have been studied using a three-fluid model, and the model predictions have been compared with observations. The comparison indicates that, for supercritical fast shocks, the three-fluid model can explain cross-shock minor ion heating which is significantly greater than that of protons. When the ratio of specific heats for minor ions, gamma (alpha), equals 2, both the lesser cross-shock deceleration and the greater heating of minor ions than of protons can be predicted by the model; thus, the minor ion heating through the shock transition region is consistent with the involvement of two degrees of freedom. Because the analysis is formulated in the de Heffmann-Teller frame of reference, the method is not valid for perpendicular shocks or when the angle is large. These results agree with the few extant observations and might be confirmed by further observations at the earth's bow shock.

Zhao, Xuepu↗

Cosmic dust particle densities - Evidence for two populations of stony micrometeorites

The existence of two populations of stony micrometeorites of distinctly different densities would result in significantly different orbital evolution properties for particles from each group. The densities inferred from deceleration of meteors in the earth's atmosphere suggest a substantial amount of the meteoric material has densities of 1 g/cu cm or less (Verniani, 1973). However, measurements of microcraters on lunar rock surfaces led Brownlee et al. (1973) to the conclusion that most micrometeoroids impacting the moon had densities in the 2-4 g/cu cm range, and low-density micrometeoroids were rare. The recovery of stony micrometeorites from the earth's stratosphere after atmospheric deceleration provides the opportunity to resolve the discrepancies. Here, the densities of 12 stony micrometeorites are determined, using synchrotron X-ray fluorescence to infer the particle mass and optical microscope measurements of the volumes. The particles fall into two distinct density groups, with mean values of 0.6 and 1.9 g/cu cm. The factor of 3 difference in the mean densities between the two populations implies differences in the orbital evolution time scales.

Flynn, G. J.↗

Study Of Spacecraft Capsule Reentering The Atmosphere

Report describes computational study of heating and deceleration of crew capsule of spacecraft entering atmosphere of Earth upon return from Mars. Issues pertaining to heating and deceleration considered in context of related issues pertaining to navigation, maneuverability of spacecraft, and safety.

Tauber, Michael↗

Generating Smooth Motions For Robotic Manipulators

In improved method for generating trajectory of robotic manipulator, each straight-line segment of trajectory composed of constant-velocity main portion sandwiched between smooth acceleration at start and smooth deceleration at finish. Algorithm implementing method computes velocity in each accelerating portion as sinusoidal function of position along line. This motion chosen for two reasons: closely approximates motion of human hand along straight-line trajectory, and provides very smooth transitions between constant-velocity portion and accelerated and decelerational end portions.

Bejczy, Antal K.↗

Physiologically constrained aerocapture for manned Mars missions

Aerobraking has been proposed as a critical technology for manned missions to Mars. The variety of mission architectures currently under consideration presents aerobrake designers with an enormous range of potential entry scenarios. Two of the most important considerations in the design of an aerobrake are the required control authority (lift-to-drag ratio) and the aerothermal environment which the vehicle will encounter. Therefore, this study examined the entry corridor width and stagnation-point heating rate and load for the entire range of probable entry velocities, lift-to-drag ratios, and ballistic coefficients for capture at both Earth and Mars. To accomplish this, a peak deceleration limit for the aerocapture maneuvers had to be established. Previous studies had used a variety of load limits without adequate proof of their validity. Existing physiological and space flight data were examined, and it was concluded that a deceleration limit of 5 G was appropriate. When this load limit was applied, numerical studies showed that an aerobrake with an L/D of 0.3 could provide an entry corridor width of at least 1 degree for all Mars aerocaptures considered with entry velocities up to 9 km/s. If 10 km/s entries are required, an L/D of 0.4 to 0.5 would be necessary to maintain a corridor width of at least 1 degree. For Earth return aerocapture, a vehicle with an L/D of 0.4 to 0.5 was found to provide a corridor width of 0.7 degree or more for all entry velocities up to 14.5 km/s. Aerodynamic convective heating calculations were performed assuming a fully catalytic, 'cold' wall; radiative heating was calculated assuming that the shock layer was in thermochemical equilibrium. Heating rates were low enough for selected entries at Mars that a radiatively cooled thermal protection system might be feasible, although an ablative material would be required for most scenarios. Earth return heating rates were generally more severe than those encountered by the Apollo vehicles, and would require ablative heat shields in all cases.

Lyne, James Evans↗

Geophysical parameters from the analysis of laser ranging to Starlette

The University of Texas Center for Space Research (UT/CSR) research efforts covering the time period from August 1, 1990 through January 31, 1991 have concentrated on the following areas: (1) Laser Data Processing (more than 15 years of Starlette data (1975-90) have been processed and cataloged); (2) Seasonal Variation of Zonal Tides (observed Starlette time series has been compared with meteorological data-derived time series); (3) Ocean Tide Solutions . (error analysis has been performed using Starlette and other tide solutions); and (4) Lunar Deceleration (formulation to compute theoretical lunar deceleration has been verified and applied to several tidal solutions). Concise descriptions of research achievement for each of the above areas are given. Copies of abstracts for some of the publications and conference presentations are included in the appendices.

Schutz, B. E.↗

Speeds and accelerations of coronal mass ejections

More than 1300 coronal mass ejections have been detected in observations made by the coronagraph aboard SMM during 1980 and 1984-1989. The speed (projected onto the plane of the sky) for at least one morphoplogical feature in about half of these mass ejections could be measured. The average speed of all mass ejection features was about 350 km/s, but speeds range from a few 10s of km/s to more than 2000 km/s. There also appear to be significant variations between the speed distributions for different years. When a mass ejection feature appeared in three or more sequential images, its acceleration could also be calculated. But, because of the limited time a mass ejection remained in the SMM field of view, the ability to detect any given acceleration diminished with increasing mass ejection speed. In fact, the SMM observations do not reveal a discernable acceleration for most mass ejections. A modest yet credible acceleration was detected in 136 cases, while a deceleration was detected in only 7 cases. The LASCO coronagraph will have a more extensive field of view than the SMM instrument; hence, with these new SOHO (Solar and Heliospheric Observatory) observations, some of the challenging questions concerning mass ejection dynamics can be addressed. How far away from the Sun does the material in a mass ejection continue being accelerated? At what radial distance is the motion of the mass ejection dominated by deceleration as it interacts with the ambient interplanetary material?

St.cyr, O. Chris↗

Polar wind ion dynamics in the magnetotail

The circulation of polar wind ions from the high-latitude ionosphere to the plasma sheet is investigated. Single-particle trajectory simulations for the geomagnetic tail show, in addition to the breaking of adiabaticity, the possible creation of new high-altitude mirror points. This trajectory feature results from an intense parallel deceleration imparted by the magnetic field rotation during fast ExB transport. This centrifugal deceleration yields a critical parallel velocity which depends on the magnitude of the convection electric field and below which ions remain trapped inside the neutral sheet.

Delcourt, D. C.↗

The effects of history and predictive information on the ability of the transport aircraft pilot to predict an alert

The early detection of a developing aircraft-subsystem fault has the potential to lessen its ultimate severity. The lack of capability for such early detection is becoming critical in the aviation community. In the commercial sector, for example, twin-engine aircraft are being used for extended transport operations over water. One method to decrease the severity of a developing problem is to predict its behavior and to take appropriate corrective action. In order to investigate pilots' ability to predict events, an experiment was conducted where eighteen airline pilots predicted the time to an alert using three different displays of dials and three different time profile complexities. The three displays of dials were as follows: standard, resembling current aircraft dial presentations; history, indicating the value five seconds in the past; and predictive, indicating the value five seconds into the future. The time profiles describing the behavior of the parameter consisted of constant velocity profiles, decelerating profiles, and accelerating then decelerating profiles. Although pilots indicated that they preferred the predictive dial, the objective data did not support its use. The objective data did show that the time profiles had the most significant effect on performance in estimating the time to an alert.

Trujillo, Anna C.↗

Energy considerations in computational aeroacoustics

A finite-volume multistage time-stepping Euler code is used to investigate the use of CFD algorithms for the direct calculation of acoustics. The 2D compressible inviscid flow about an accelerating or decelerating circular cylinder is used as a model problem. The time evolution of the energy transfer from the cylinder to the fluid, as the cylinder is moved from rest to some nonnegligible velocity, is clearly seen. By examining the temporal and spatial characteristics of the numerical solution, a distinction can be made between the propagating acoustic energy, the convecting energy associated with the entropy change in the fluid, and the energy contained in the local aerodynamic field. Systematic variation of the cylinder acceleration shows that the radiated acoustic energy depends strongly upon the rate of acceleration or deceleration. The computational grid has a large effect on the ratio of acoustic energy to nonphysical entropy associated energy, while the role of the explicit artificial viscosity seems to be of second order. The entropy term was nearly negligible in all cases the cylinder was started slowly.

Brentner, Kenneth S.↗