Search NASA⌕ Search

SEARCH · Search NASA

Results for “Dislocation structure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42

In situ measurements of a homogeneous to heterogeneous transition in the plastic response of ion-irradiated <111> Ni microspecimens

We report on the use of quantitative in situ microcompression experiments in a scanning electron microscope to systematically investigate the effect of self-ion irradiation damage on the full plastic response of <111> Ni. In addition to the well-known irradiationinduced increases in the yield and flow strengths with increasing dose, we measure substantial changes in plastic flow intermittency behavior, manifested as stress drops accompanying energy releases as the driven material transits critical states. At low irradiation doses, the magnitude of stress drops reduces relative to the unirradiated material and plastic slip proceeds on multiple slip systems, leading to quasi-homogeneous plastic flow. In contrast, highly irradiated specimens exhibit pronounced shear localization on parallel slip planes, which we ascribe to the onset of defect free channels normally seen in bulk irradiated materials. Our in situ testing system and approach allows for a quantitative study of the energy release and dynamics associated with defect free channel formation and subsequent localization. As a result, this study provides fundamental insight to the nature of interactions between mobile dislocations and irradiation-mediated and damage-dependent defect structures.

36 MATERIALS SCIENCE↗

Origins of radiation-induced optical attenuation in neutron-irradiated single-crystal sapphire at elevated temperatures

Sapphire (α-Al 2 O 3 ) is a candidate fiber-optic sensor material for extreme temperature environments, potentially including those of nuclear reactors. However, its optical transmission under high-dose neutron irradiation is not well understood compared with that of conventional fused silica. This study examined dimensional changes, optical transmission, and irradiation-induced defects in neutron-irradiated α-Al 2 O 3 at temperatures of 298 °C to 688 °C and doses of 3.2 to 12 dpa. Although previous studies attributed radiation-induced attenuation (RIA) at the highest irradiation temperatures to increased optical scattering from radiation-induced voids, our findings indicate that scattering from neither voids nor dislocation loops can explain the measured attenuation. Instead, absorption due to aluminum vacancy centers appears more likely based on a comparison of the spectral features of the measured optical attenuation with previous literature. Significant c-axis swelling (5.51 % ± 0.83 %) was observed in the 12 dpa, 592 °C irradiated sample, much higher than earlier measurements, suggesting temperature sensor drift of 543 °C to 1,140 °C. Void patterning was predominantly observed along the a-axis, differing from previous studies on polycrystalline samples, which showed c-axis patterning. Dislocation loops evolved into network dislocations with increasing temperature and dose; voids formed within these structures, showing no size or density changes, indicating an atypical growth mechanism.

Neutron irradiation↗

Mechanical properties, strain hardening, and fracture behavior of ultrasonic additively manufactured Zircaloy-4 after low-temperature neutron irradiation

Ultrasonic additive manufacturing (UAM) is a solid-state, layer-by-layer advanced manufacturing process that has the potential to create custom spatially controlled composites with embedded wires and sensors for nuclear component manufacture. For this work, to assess the feasibility of using UAM for nuclear-relevant materials research, the technique was used to produce a 3.5-mm-thick Zircaloy-4 plate for irradiation testing. The UAM Zircaloy-4 specimens were irradiated in the High Flux Isotope Reactor at a target irradiation temperature of 117 °C to 2.9 displacements per atom (dpa) to assess differences in irradiation-hardening behavior as a function of alloy processing path. The UAM and reference baseplate (BP) materials increased in yield strength by 372±27 MPa and 346±21 MPa, respectively, and both suffered significant reductions in uniform and total elongation attributed to irradiation hardening at low-temperature. Although the materials had similar nanoscale defect structures, including nanoscale black dot/loop features and strain-induced dislocation channels, the UAM material’s processing-related defects resulted in accelerated strain localization and failure as demonstrated by lower post-irradiation uniform elongation of UAM specimens (0.5 %) compared to BP (1.5 %) material. The UAM material also showed considerable anisotropy in mechanical response due to crack propagation along weld boundaries, resulting in differences in strength & ductility when tested parallel and perpendicular to the prior UAM build orientation. Therefore, although the fundamental irradiation response of UAM-processed Zircaloy-4 was phenomenologically comparable to that of BP reference material, additional optimization of the UAM processing is needed to produce irradiation-resistant and nuclear-relevant materials.

Digital image correlation↗

Computational Study of Short-Pulse Laser-Induced Generation of Crystal Defects in Ni-Based Single-Phase Binary Solid–Solution Alloys

Single-phase concentrated solid–solution alloys exhibit enhanced mechanical characteristics and radiation damage resistance, making them promising candidate materials for applications involving an exposure to rapid localized energy deposition. We use large-scale atomistic modeling to investigate the mechanisms of the generation of vacancies, dislocations, stacking faults, and twin boundaries in Ni, Ni 50 Fe 50 , Ni 80 Fe 20 , and Ni 80 Cr 20 targets irradiated by short laser pulses in the regime of melting and resolidification. The decrease in the thermal conductivity and strengthening of the electron–phonon coupling due to the intrinsic chemical disorder in the solid-solution alloys are found to have important implications on localization of the energy deposition and generation of thermoelastic stresses. The interaction of the laser-induced stress waves with the melting front is found to play a key role in roughening of the crystal–liquid interface and generation of dislocations upon the solidification. A common feature revealed in the structural analysis of all irradiated targets is the presence of high vacancy concentrations exceeding the equilibrium values at the melting temperature by about an order of magnitude. On the basis of the results of molecular dynamics simulations of solidification occurring at fixed levels of undercooling, the generation of vacancies is correlated with the velocity of the solidification front, and the processes responsible for creating the strong vacancy supersaturation are revealed. The suppression of the vacancy generation in the solid–solution alloys is also revealed and related to combined effect of enhanced vacancy mobility and higher energy of the vacancy formation in the alloy systems. The analysis of the first atomic shells surrounding the vacancy sites in Ni–Fe alloys uncovers the preference for the vacancy sites to be surrounded by Fe atoms and suggests that atomic-scale chemical heterogeneities may play an important role in defining the behavior and properties of the single-phase concentrated solid-solution alloys.

36 MATERIALS SCIENCE↗

Lorentz electron ptychography for imaging magnetic textures beyond the diffraction limit

Nanoscale spin textures, especially magnetic skyrmions, have attracted intense interest as candidate high-density and power-efficient information carriers for spintronic devices. Facilitating a deeper understanding of sub-100 nm to atomic-scale spin textures requires more advanced magnetic imaging techniques. Here, we demonstrate a Lorentz electron ptychography (LEP) method which can enable high-resolution, high-sensitivity magnetic field imaging for widely-available electron microscopes. The resolution of LEP is not limited by the usual diffraction limit of the lens optics, but instead is determined by the maximum scattering angle at which a statistically meaningful dose can still be recorded – this can be an improvement of up to 2 to 6 times depending on the allowable dose. Using FeGe as a model system, we realize a more accurate magnetic field measurement of skyrmions with an improved spatial resolution and sensitivity by also correcting the probe damping effects from the imaging optics via LEP. This allows us to directly resolve subtle internal structures of magnetic skyrmions near the skyrmion cores, boundaries, and dislocations in an FeGe single crystal. Our study establishes a quantitative, high-resolution magnetic microscopy technique that can reveal the nanoscale spin textures, especially magnetization discontinuities and topological defects in nanomagnets. In conclusion, the technique’s high dose efficiency should also make it well-suited for the exploration of magnetic textures in electron radiation-sensitive materials such as organic or molecular magnets.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Composition and strain in thin Si{sub 1-x}Ge{sub x} virtual substrates measured by micro-Raman spectroscopy and x-ray diffraction

Micro-Raman spectroscopy was employed for the determination of the germanium content, x and strain, {epsilon}, in ultrathin SiGe virtual substrates grown directly on Si by molecular beam epitaxy. The growth of highly relaxed SiGe layers was achieved by the introduction of point defects at a very low temperature during the initial stage of growth. SiGe virtual substrates with thicknesses in the range 40-200 nm with a high Ge content (up to 50%) and degree of relaxation, r, in the range 20%-100% were investigated using micro-Raman spectroscopy and x-ray diffraction (XRD) techniques. The Ge content, x, and strain, {epsilon}, were estimated from equations describing Si-Si, Si-Ge, and Ge-Ge Raman vibrational modes, modified in this study for application to thin SiGe layers. The alteration of the experimentally derived equations from previous studies was performed using independent data for x and r obtained from XRD reciprocal space maps. A number of samples consisting of a strained-silicon (s-Si) layer deposited on a SiGe virtual substrate were also analyzed. The stress value for the s-Si varied from 0.54 to 2.75 GPa, depending on the Ge-content in the virtual substrates. These results are in good agreement with theoretically predicted values.

36 MATERIALS SCIENCE↗

Molecular beam epitaxy growth of high quality p-doped SnS van der Waals epitaxy on a graphene buffer layer

We report on the systematic investigation of optoelectronic properties of tin (IV) sulfide (SnS) van der Waals epitaxies (vdWEs) grown by molecular beam epitaxy (MBE) technique. Energy band simulation using commercial CASTEP code indicates that SnS has an indirect bandgap of size 0.982 eV. Furthermore, our simulation shows that elemental Cu can be used as a p-type dopant for the material. Growth of high quality SnS thin films is accomplished by MBE technique using graphene as the buffer layer. We observed significant reduction in the rocking curve FWHM over the existing published values. Crystallite size in the range of 2-3 {mu}m is observed which is also significantly better than the existing results. Measurement of the absorption coefficient, {alpha}, is performed using a Hitachi U-4100 Spectrophotometer system which demonstrate large values of {alpha} of the order of 10{sup 4} cm{sup -1}. Sharp cutoff in the values of {alpha}, as a function of energy, is observed for the films grown using a graphene buffer layer indicating low concentration of localized states in the bandgap. Cu-doping is achieved by co-evaporation technique. It is demonstrated that the hole concentration of the films can be controlled between 10{sup 16} cm{sup -3} and 5 x 10{sup 17}cm{sup -3} by varying the temperature of the Cu K-cell. Hole mobility as high as 81 cm{sup 2}V{sup -1}s{sup -1} is observed for SnS films on graphene/GaAs(100) substrates. The improvements in the physical properties of the films are attributed to the unique layered structure and chemically saturated bonds at the surface for both SnS and the graphene buffer layer. Consequently, the interaction between the SnS thin films and the graphene buffer layer is dominated by van der Waals force and structural defects at the interface, such as dangling bonds or dislocations, are substantially reduced.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Domain epitaxy in TiO2/ -Al2O3 thin film heterostructures with Ti2O3 transient layer

Rutile TiO2 films were grown epitaxially on -alumina (sapphire(0001)) substrates and characterized by x-ray diffraction and scanning transmission electron microscopy. It was revealed that the rutile film initially grows pseudomorphically on sapphire as Ti2O3 and, after a few monolayers, it grows tetragonally on the Ti2O3/sapphire platform. Formation of the Ti2O3 transient layer was attributed to the symmetry mismatch between tetragonal structure of TiO2 and hexagonal structure of alumina. The separation between the [10](101) misfit dislocations was dictated by Ti2O3 and was determined to be 9.7 which is consistent with 4/3 and 3/2 alternating domains across the film/substrate interface.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Misfit strain driven cation inter-diffusion across an epitaxial multiferroic thin film interface

Cation intermixing at functional oxide interfaces remains a highly controversial area directly relevant to interface-driven nanoelectronic device properties. Here, we systematically explore the cation intermixing in epitaxial (001) oriented multiferroic bismuth ferrite (BFO) grown on a (001) lanthanum aluminate (LAO) substrate. Aberration corrected dedicated scanning transmission electron microscopy and electron energy loss spectroscopy reveal that the interface is not chemically sharp, but with an intermixing of ∼2 nm. The driving force for this process is identified as misfit-driven elastic strain. Landau-Ginzburg-Devonshire-based phenomenological theory was combined with the Sheldon and Shenoy formula in order to understand the influence of boundary conditions and depolarizing fields arising from misfit strain between the LAO substrate and BFO film. The theory predicts the presence of a strong potential gradient at the interface, which decays on moving into the bulk of the film. This potential gradient is significant enough to drive the cation migration across the interface, thereby mitigating the misfit strain. Our results offer new insights on how chemical roughening at oxide interfaces can be effective in stabilizing the structural integrity of the interface without the need for misfit dislocations. These findings offer a general formalism for understanding cation intermixing at highly strained oxide interfaces that are used in nanoelectronic devices.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Towards large size substrates for III-V co-integration made by direct wafer bonding on Si

We report the first demonstration of 200 mm InGaAs-on-insulator (InGaAs-o-I) fabricated by the direct wafer bonding technique with a donor wafer made of III-V heteroepitaxial structure grown on 200 mm silicon wafer. The measured threading dislocation density of the In{sub 0.53}Ga{sub 0.47}As (InGaAs) active layer is equal to 3.5 × 10{sup 9} cm{sup −2}, and it does not degrade after the bonding and the layer transfer steps. The surface roughness of the InGaAs layer can be improved by chemical-mechanical-polishing step, reaching values as low as 0.4 nm root-mean-square. The electron Hall mobility in 450 nm thick InGaAs-o-I layer reaches values of up to 6000 cm{sup 2}/Vs, and working pseudo-MOS transistors are demonstrated with an extracted electron mobility in the range of 2000–3000 cm{sup 2}/Vs. Finally, the fabrication of an InGaAs-o-I substrate with the active layer as thin as 90 nm is achieved with a Buried Oxide of 50 nm. These results open the way to very large scale production of III-V-o-I advanced substrates for future CMOS technology nodes.

36 MATERIALS SCIENCE↗

Electroluminescence from GeSn heterostructure pin diodes at the indirect to direct transition

The emission properties of GeSn heterostructure pin diodes have been investigated. The devices contain thick (400–600 nm) Ge{sub 1−y}Sn{sub y} i-layers spanning a broad compositional range below and above the crossover Sn concentration y{sub c} where the Ge{sub 1−y}Sn{sub y} alloy becomes a direct-gap material. These results are made possible by an optimized device architecture containing a single defected interface thereby mitigating the deleterious effects of mismatch-induced defects. The observed emission intensities as a function of composition show the contributions from two separate trends: an increase in direct gap emission as the Sn concentration is increased, as expected from the reduction and eventual reversal of the separation between the direct and indirect edges, and a parallel increase in non-radiative recombination when the mismatch strains between the structure components is partially relaxed by the generation of misfit dislocations. An estimation of recombination times based on the observed electroluminescence intensities is found to be strongly correlated with the reverse-bias dark current measured in the same devices.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Specific features of NH{sub 3} and plasma-assisted MBE in the fabrication of III-N HEMT heterostructures

The specific features of how nitride HEMT heterostructures are produced by NH{sub 3} and plasma-assisted (PA) molecular-beam epitaxy (MBE) are considered. It is shown that the use of high-temperature AlN/AlGaN buffer layers grown with ammonia at extremely high temperatures (up to 1150°C) can drastically improve the structural perfection of the active GaN layers and reduce the dislocation density in these layers to values of 9 × 10{sup 8}−1 × 10{sup 9} cm{sup −2}. The use of buffer layers of this kind makes it possible to obtain high-quality GaN/AlGaN heterostructures by both methods. At the same time, in contrast to ammonia MBE which is difficult to apply at T < 500°C (because of the low efficiency of ammonia decomposition), PA MBE is rather effective at low temperatures, e.g., for the growth of InAlN layers lattice-matched with GaN. The results obtained in the MBE growth of AlN/AlGaN/GaN/InAlN heterostructures by both PA-MBE and NH{sub 3}-MBE with an extremely high ammonia flux are demonstrated.

36 MATERIALS SCIENCE↗

A Platform-Independent X-ray Diffraction Diagnostic for Phase Transition Kinetics in Traditional and Synthetic Microstructure Materials (LDRD Project 213088 Final Report)

Pulsed-power generators using the magnetic loading technique are able to produce well-controlled continuous ramp compression of condensed matter for high-pressure equation-of-state studies. X-ray diffraction (XRD) data from dynamically compressed samples provide direct measurements of the elastic compression of the crystal lattice, onset of plastic flow, strength-strain rate dependence, structural phase transitions, and density of crystal defects such as dislocations. Here, we present a cost effective, compact X-ray source for XRD measurements on pulsed-power-driven ramp-loaded samples. This combination of magnetically-driven ramp compression of materials with single, short-pulse XRD diagnostic will be a powerful capability for the dynamic materials community. The success in fielding this new XRD diagnostic dramatically improves our predictive capability and understanding of rate-dependent behavior at or near phase transition. As Sandia plans the next-generation pulse-power driver platform, a key element needed to deliver new state-of-the-art experiments will be having the necessary diagnostic tools to probe new regimes and phenomena. These diagnostics need to be as versatile, compact, and portable as they are powerful. The development of a platform-independent XRD diagnostic gives Sandia researchers a new window to study the microstructure and phase dynamics of materials under load. This project has paved the way for phase transition research in a variety of materials with mission interest.

36 MATERIALS SCIENCE↗

On the effect of deep-rolling and laser-peening on the stress-controlled low- and high-cycle fatigue behavior of Ti-6Al-4V at elevated temperatures up to 550?C

The effect of surface treatment on the stress/life fatigue behavior of a titanium Ti-6Al-4V turbine fan blade alloy is investigated in the regime of 102 to 106 cycles to failure under fully reversed stress-controlled isothermal push-pull loading between 25? and 550?C at a frequency of 5 Hz. Specifically, the fatigue behavior was examined in specimens in the deep-rolled and laser-shock peened surface conditions, and compared to results on samples in the untreated (machined and stress annealed) condition. Although the fatigue resistance of the Ti-6Al-4V alloy declined with increasing test temperature regardless of surface condition, deep-rolling and laser-shock peening surface treatments were found to extend the fatigue lives by factors of more than 30 and 5-10, respectively, in the high-cycle and low-cycle fatigue regimes at temperatures as high as 550?C. At these temperatures, compressive residual stresses are essentially relaxed; however, it is the presence of near-surface work hardened layers, with a nanocystalline structure in the case of deep-rolling and dense dislocation tangles in the case of laser-shock peening, which remain fairly stable even after cycling at 450?-550?C, that provide the basis for the beneficial role of mechanical surface treatments on the fatigue strength of Ti-6Al-4V at elevated temperatures.

36 MATERIALS SCIENCE↗

High optical and structural quality of GaN epilayers grown on (2{sup ¯}01) β-Ga{sub 2}O{sub 3}

Producing highly efficient GaN-based optoelectronic devices has been a challenge for a long time due to the large lattice mismatch between III-nitride materials and the most common substrates, which causes a high density of threading dislocations. Therefore, it is essential to obtain alternative substrates with small lattice mismatches, appropriate structural, thermal and electrical properties, and a competitive price. Our results show that (2{sup ¯}01) oriented β-Ga{sub 2}O{sub 3} has the potential to be used as a transparent and conductive substrate for GaN-growth. Photoluminescence spectra of thick GaN layers grown on (2{sup ¯}01) oriented β-Ga{sub 2}O{sub 3} are found to be dominated by intense bandedge emission. Atomic force microscopy studies show a modest threading dislocation density of ∼10{sup 8 }cm{sup −2}. X-ray diffraction studies show the high quality of the single-phase wurtzite GaN thin film on (2{sup ¯}01) β-Ga{sub 2}O{sub 3} with in-plane epitaxial orientation relationships between the β-Ga{sub 2}O{sub 3} and the GaN thin film defined by (010) β-Ga{sub 2}O{sub 3} || (112{sup ¯}0) GaN and (2{sup ¯}01) β-Ga{sub 2}O{sub 3} || (0001) GaN leading to a lattice mismatch of ∼4.7%. Complementary Raman spectroscopy indicates that the quality of the GaN epilayer is high.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Fatigue and Creep-Fatigue Deformation of an Ultra-Fine Precipitate Strengthened Advanced Austenitic Alloy

An advanced austenitic alloy, HT-UPS (high-temperature ultrafine-precipitation-strengthened), has been identified as an ideal candidate material for the structural components of fast reactors and energy-conversion systems. HT-UPS alloys demonstrate improved creep resistance relative to 316 stainless steel (SS) through additions of Ti and Nb, which precipitate to form a widespread dispersion of stable nanoscale metallic carbide (MC) particles in the austenitic matrix. The low-cycle fatigue and creep-fatigue behavior of an HT-UPS alloy have been investigated at 650 °C and a 1.0% total strain, with an R-ratio of -1 and hold times at peak tensile strain as long as 150 min. The cyclic deformation response of HT-UPS is directly compared to that of standard 316 SS. The measured values for total cycles to failure are similar, despite differences in peak stress profiles and in qualitative observations of the deformed microstructures. Crack propagation is primarily transgranular in fatigue and creep-fatigue of both alloys at the investigated conditions. Internal grain boundary damage in the form of fine cracks resulting from the tensile hold is present for hold times of 60 min and longer, and substantially more internal cracks are quantifiable in 316 SS than in HT-UPS. The dislocation substructures observed in the deformed material differ significantly; an equiaxed cellular structure is observed in 316 SS, whereas in HT-UPS the microstructure takes the form of widespread and relatively homogenous tangles of dislocations pinned by the nanoscale MC precipitates. The significant effect of the fine distribution of precipitates on observed fatigue and creep-fatigue response is described in three distinct behavioral regions as it evolves with continued cycling.

36 MATERIALS SCIENCE↗

Resilient Pathways to Atomic Attachment of Quantum Dot Dimers and Artificial Solids from Faceted CdSe Quantum Dot Building Blocks

Here, the goal of this work is to identify favored pathways for preparation of defect-resilient attached wurtzite CdX (X = S, Se, Te) nanocrystals. We seek guidelines for oriented attachment of faceted nanocrystals that are most likely to yield pairs of nanocrystals with either few or no electronic defects or electronic defects that are in and of themselves desirable and stable. Using a combination of in situ high-resolution transmission electron microscopy (HRTEM) and electronic structure calculations, we evaluate the relative merits of atomic attachment of wurtzite CdSe nanocrystals on the {1$\bar{10}$0} or {11$\bar{20}$} family of facets. Pairwise attachment on either facet can lead to perfect interfaces, provided the nanocrystal facets are perfectly flat and the angles between the nanocrystals can adjust during the assembly. Considering defective attachment, we observe for {1$\bar{10}$0} facet attachment that only one type of edge dislocation forms, creating deep hole traps. For {11$\bar{20}$} facet attachment, we observe that four distinct types of extended defects form, some of which lead to deep hole traps whereas others only to shallow hole traps. HRTEM movies of the dislocation dynamics show that dislocations at {1$\bar{10}$0} interfaces can be removed, albeit slowly. Whereas only some extended defects at {11$\bar{20}$} interfaces could be removed, others were trapped at the interface. Based on these insights, we identify the most resilient pathways to atomic attachment of pairs of wurtzite CdX nanocrystals and consider how these insights can translate to the creation of electronically useful materials from quantum dots with other crystal structures.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Microstructure-Sensitive Uncertainty Quantification for Crystal Plasticity Finite Element Constitutive Models Using Stochastic Collocation Methods

Uncertainty quantification (UQ) plays a major role in verification and validation for computational engineering models and simulations, and establishes trust in the predictive capability of computational models. In the materials science and engineering context, where the process-structure-property-performance linkage is well known to be the only road mapping from manufacturing to engineering performance, numerous integrated computational materials engineering (ICME) models have been developed across a wide spectrum of length-scales and time-scales to relieve the burden of resource-intensive experiments. Within the structure-property linkage, crystal plasticity finite element method (CPFEM) models have been widely used since they are one of a few ICME toolboxes that allows numerical predictions, providing the bridge from microstructure to materials properties and performances. Several constitutive models have been proposed in the last few decades to capture the mechanics and plasticity behavior of materials. While some UQ studies have been performed, the robustness and uncertainty of these constitutive models have not been rigorously established. In this work, we apply a stochastic collocation (SC) method, which is mathematically rigorous and has been widely used in the field of UQ, to quantify the uncertainty of three most commonly used constitutive models in CPFEM, namely phenomenological models (with and without twinning), and dislocation-density-based constitutive models, for three different types of crystal structures, namely face-centered cubic (fcc) copper (Cu), body-centered cubic (bcc) tungsten (W), and hexagonal close packing (hcp) magnesium (Mg). Our numerical results not only quantify the uncertainty of these constitutive models in stress-strain curve, but also analyze the global sensitivity of the underlying constitutive parameters with respect to the initial yield behavior, which may be helpful for robust constitutive model calibration works in the future.

36 MATERIALS SCIENCE↗