Search NASA⌕ Search

SEARCH · Search NASA

Results for “EUTECTICS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

Influence of Melt-Pouring Temperature and Composition of Primary Coating of Shell Mold on Tensile Strength and Creep Resistance of Ni-Based Superalloy

Eight investment castings of Inconel 713C superalloy were fabricated, varying in the melt-pouring temperature, from 1400 to 1520 °C, and CoAl{sub 2}O{sub 4} inoculant content, 0 or 5 wt.%, in the primary coat. Their influence on grain size on tensile and creep properties was investigated. The best combination of yield stress (815 MPa) and elongation (A{sub 4} = 7.65%) at ambient temperature was obtained in surface-modified castings poured from 1520 °C. The longest time to rupture was for the unmodified castings (76.8 h) poured from 1520 °C, while for the modified variant, the time to rupture was lower around, 7.4 h, which was still a satisfactory value. During tensile testing, microcracks were formed in large eutectic γ′, carbides and borides, due to the accumulation of stress at interfaces with the matrix. During creep, N-type rafting of γ′ precipitates and phase transformation MC + γ → γ′ + M{sub 23}C{sub 6} took place.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Effect of Ti Modification on Microstructures and Properties of Carbidic Austempered Ductile Iron

In this paper, we investigated the effect of titanium modification on microstructures and properties of carbidic austempered ductile iron (CADI) containing 3.72 wt.% C, 2.77 wt.% Si, and 0.51 wt.% Mn. The results showed that with the addition of 0.1 wt.% Ti, TiC particles were formed, and distributed in carbides and matrix. Microstructural observation indicated that the maximum diameter of graphite nodules decreased from 58 to 40 μm, and the shape of carbides transformed from network to fragmentation, which was related to the nucleation of the eutectic structure (γ + (Fe, Cr){sub 3}C) where TiC particles act as the nucleus. After isothermal quenching at 300 °C, the hardness of Ti-bearing CADI was 3.5 HRC higher than ordinary CADI, and the impact toughness was increased by 14.3%. Additionally, due to the decrease in exfoliation, the wear loss of Ti-bearing CADI was 14.8% lower than ordinary CADI during the block-on-ring wear test at the surface load of 300 N.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Effects of Laser Fluence on Microstructure and Bonding Characteristics of Wideband Laser-Deposited Nickel Composite Coatings

The wideband laser has shown great potential in metal–ceramic coatings deposition due to the high efficiency and low dilution rate. However, the effects of wideband laser process on microstructure evolution and bonding mechanism at the coatings/substrate interface are still a critical problem and need further investigation. In this work, nickel composite coatings are fabricated on the surface high-strength low-alloy steel. The effects of laser fluence on microstructure evolution, shear strength and fracture mechanism are studied. Results indicated the added WC particles were partly dissolved due to the high-power laser irradiation. Many block precipitates and dense eutectic were synthesized in composite coatings. Reinforced phases mainly consist of Cr{sub 5}B{sub 3}, Cr{sub 23}C{sub 6}, W{sub 2}C and Cr{sub 3}Ni{sub 2}. The dilution of Q550 steel contributed to the formation of nickel dendrites and facilitated a dense metallurgical bonding at coating/substrate interface when laser fluence was high. Shear strength tests indicated the laser fluence and shear strength had a positive correlation. For Ni60/WC composite coatings designed in these experiments, the recommend laser fluence should be higher than 55 J/mm{sup 2}, above which the shear strength could be greater than 200 MPa. Fracture surfaces indicated the failure mechanism of composite coatings was quasi-cleavage fracture.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Effects of Bi-Sb Addition and Solution Treatment on Microstructures and Mechanical Properties of Al-20 wt.% Mg{sub 2}Si Composites

In this study, the effects of compound modification with Bi and Sb and solution treatment on the microstructures evolution and the mechanical properties of Al-20 wt.% Mg{sub 2}Si composites were investigated. The specimens were observed by optical microscope, scanning electron microscope equipped with an energy-dispersive spectrometer and x-ray diffraction. The characterization results showed that 2.0 wt.% Sb and 0.2 wt.% Bi addition refined the primary Mg{sub 2}Si from 95 to 10 μm, accompanied by a change in morphology from coarse dendrites to dispersive fine polygons. After solution treatment at 540 °C for 15 h, the sharp polygonal primary Mg{sub 2}Si particles were blunted and the flake-like eutectic Mg{sub 2}Si phases were changed to small spherical particles, resulting in the increase in the Brinell hardness of the composites from HB 94.53 to 134.67. Mechanical tests revealed that both tensile strength and hardness of the composite were improved by compound modification with Bi and Sb, and the ultimate tensile strength (UTS) was increased from 216 MPa unmodified to 257 MPa with optimum modification of 2 wt.% Sb and 0.2 wt.% Bi. A propounded change in hardness from HB 94.53 to 130.67 was also investigated.

36 MATERIALS SCIENCE↗
DOE OSTI2019

The Influence of Shell Mold Composition on the As-cast Macro- and Micro-structure of Thin-Walled IN713C Superalloy Castings

In the investment casting process, the building of ceramic layers around the wax pattern is the main time-consuming stage. Increasing their number ensures sufficient mechanical properties, but also lengthens the whole process, including drying time and preheating of the mold. Four molds for casting Ni-based superalloy IN713C were strengthened by glass fibers, included in the slurry, and metal powder, of Al, Cu, Fe or Ni, in the coverage. Castings were subjected to microstructural investigations in order to find out if the new design can be promising for the manufacture of jet engine components. Bend tests revealed that the green strengths of all new molds were higher, at least 3.65 MPa, than that of the unmodified molds, 3.0 MPa. Optical microscopy revealed that the composition of a mold had a strong influence on stereological parameters of equiaxed IN713C grains. Microstructural observation and hardness measurements of castings revealed differences in the volume fraction of strengthening phases, porosity and hardness. The microstructure due to the complex chemical composition of IN713C consisted of several phases including ternary eutectics as a consequence of L → γ + Ni{sub 7}Zr{sub 2} + (Nb, Zr)C.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Effects of Transition Layer on Bending Resistance in Copper-Clad Aluminum Composite Casting

The performance of the transition layer in a Cu/Al composite casting directly affects the quality of subsequent plastic deformation processing; however, there are no universal or standardized measurement indices for the performance of the transition layer. In this study, Cu/Al composite castings were prepared using the pouring aluminum method, and the resulting solidification microstructures on the bending resistance were investigated. The results of this study lay a theoretical foundation for the development of the plastic processing technologies of these composite castings. A thinner transition layer in the Cu/Al composite casting led to improved bending resistance. In addition, for a fixed total thickness of the transition layer, the bending resistance was mainly controlled by the γ/β interface and β + eutectic (α + β) microstructure, and the thickness of the γ phase had a negligible effect on the bending resistance. The γ/β interface cracked first when the transition layer bore the tensile and shear stress during the bending process, which resulted in the transition layer easily separating from the copper. The bending resistance of the transition layer can be feasibly judged by measuring the bending angle of the specimen tip, which can be easily performed when the specimen bends toward the aluminum direction, suggesting that our proposed method has considerable practical significance.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Microstructure and Mechanical Properties of a SiO{sub 2} Ceramic and TC4 Alloy Joint Brazed with a Nanocomposite Filler

Vacuum brazing of TC4 alloy and SiO{sub 2} ceramic was achieved using a nano-AgCuNi braze alloy. The melting temperature of nano-AgCu powders was analyzed by differential scanning calorimeter. Furthermore, the effects of the Ni content on the microstructure and mechanical properties of the joints were studied. The results showed that the melting temperature of the nano-AgCu filler was 774 °C. A decrease in the melting temperature of 6 °C was observed, compared with the general AgCu filler, and this decrease enabled the interfacial reaction of the joint to begin earlier. The typical interfacial microstructure of the TC4/nano-AgCuNi/SiO{sub 2} ceramic joint brazed at 950 °C for 10 min was TC4/α-Ti + Ti{sub 2}(Cu,Ni) + Ti{sub 2}(Ni,Cu) hypereutectoid structure/Ti{sub 2}(Cu,Ni) compound with α-Ti + Ti{sub 2}(Cu,Ni) + Ti{sub 2}(Ni,Cu) hypereutectic structure/Ti{sub 4}O{sub 7} + TiSi{sub 2}/SiO{sub 2} ceramics. The homogeneous microstructure of α-Ti + Ti{sub 2}(Cu,Ni) + Ti{sub 2}(Ni,Cu) hypereutectoid structure primarily existed in the diffusion layer. Additionally, the refined α-Ti + Ti{sub 2}(Cu,Ni) + Ti{sub 2}(Ni,Cu) hypereutectic structure created via a eutectic reaction and Ti{sub 2}(Cu,Ni) compound was distributed in the brazing seam. The Ni content could influence the formation of Ti-Cu-Ni ternary intermetallic compounds (IMCs). An increase in Ni led to an increase in the α-Ti + Ti{sub 2}(Cu,Ni) + Ti{sub 2}(Ni,Cu) hypereutectic structure in the brazing seam. The shear strength of the brazed joints first increased and then decreased with the increase in the nano-Ni content, and the optimal shear strength of 30.1 MPa was achieved at 10 wt.% Ni. The increase in the α-Ti + Ti{sub 2}(Cu,Ni) + Ti{sub 2}(Ni,Cu) hypereutectic structure and the decrease in brittle compounds enhanced the shear strength of the joint. Fracture analysis of the joints brazed at 950 °C for 10 min indicated that the cracks mainly occurred in SiO{sub 2} ceramic.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Microstructure Evolution, Structural Integrity, and Hot Corrosion Performance of Nitrogen-Enhanced Stainless Steel Welds

This work articulated the multi-pass, gas tungsten arc welding by adopting pulsating current for joining nitrogen-enhanced, low-carbon austenitic stainless steel, AISI 316L(N). An austeno-ferrite stainless steel (ER2594) and an over-alloyed (ERNiCrMo-3) fillers were employed to join 6-mm-thick plates of AISI 316L(N). Acicular and lathy ferrite in the weld zone of ER2594 and the occurrence of secondary phases in the fusion zone of over-alloyed filler were observed. The notch tensile strength data attested that the joint strength was greater for the welds employing an over-alloyed filler. This study also affirms that the welds obtained with ER2594 filler resulted in better impact toughness (144 J) compared with ERNiCrMo-3 filler and base metal. Also the notch impact toughness of ER2594 weldment is increased to 60% in comparison with that of candidate metal. Corrosion studies were also performed by exposing the coupons in a eutectic salt mixture comprising of 40%K{sub 2}SO{sub 4}-60%NaCl for 50 cycles at 650 °C. It is observed that the weld zone employing over-alloyed filler experienced better high-temperature corrosion resistance compared to the base metal. The specific results of this investigation will be of greater demand to the nuclear and marine applications utilizing these joints.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Effect of Chromium Content on Microstructure, Hardness, and Wear Resistance of As-Cast Fe-Cr-B Alloy

The effects of chromium content on microstructure, hardness and wear resistance of as-cast Fe-xCr-1.0B (x = 0, 4, 8, 12, 16, 20) alloys were investigated by means of optical microscope (OM), scanning electron microscope (SEM), x-ray diffractometer (XRD), hardness tester and ring block wear tester. The results showed that the microstructures of chromium-free alloy were mainly composed of pearlite, ferrite, and eutectic borocarbides, and the hardness was very low, only 18.8 HRC. With the increase in chromium content, the matrix of as-cast Fe-Cr-B alloy gradually began to transform from pearlite and ferrite to lath martensite, and the type of borocarbides changed from Fe{sub 2}(B, C) to M{sub 2}(B, C), M{sub 7}(C, B){sub 3} and M{sub 23}(C, B){sub 6} (M = Fe, Cr). When the chromium content was 12 wt.%, the hardness of alloy reached the highest value of 61.1 HRC, and the wear resistance of alloy was the best. The results of worn surface analysis showed that the wear failure of as-cast Fe-Cr-B alloy was mainly caused by multiple plastic deformation and micro-cutting.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Laser Weldability of AlSi{sub 10}Mg Alloy Produced by Selective Laser Melting: Microstructure and Mechanical Behavior

Selective laser melting (SLM) allows 3D complex parts to be produced with integrated functionalities but does not permit to realize large dimension parts, as the building chamber volume of commercial SLM systems is limited. Therefore, the possibility of joining SLM-built parts by welding appears as extremely valuable. In this work, laser weldability of SLMed AlSi{sub 10}Mg parts has been investigated. The cooling rates induced by the welding process are lower than the ones of SLM; therefore, typical eutectic silicon network of SLM-built parts appears broken in both the melted zone and part of the heat-affected zone, as confirmed by calorimetric measurement. This microstructural evolution caused a local decrease of hardness from 132 HV to 73 HV and a reduction of ductility caused by porosity formation in the weld bead. Moreover, the thermal treatment, performed at 320°C, can limit the gap of tensile response among welded bead and base SLM material.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Improved High-Temperature Aluminum Alloys Containing Cerium

A common rare earth (cerium) when added to aluminum in compositions up to the eutectic compositions of around 10 wt.% improves the high-temperature performance of aluminum alloys. In the early 1980s, some promising research and development efforts focused on powder metallurgy revealed that aluminum alloys containing 4 wt.% cerium exhibit high-temperature mechanical properties exceeding those of the best commercial aluminum casting alloys then in production. Those compositions, which also included high levels of iron, were difficult to process. Recently, magnesium replaces iron to reduce density and improve processing. Cerium oxide is an abundant rare earth oxide that is often discarded during the refining of more valuable rare earths such as Nd and Dy. Therefore, the economics are compelling for cerium as an alloy additive. In this review, we report results obtained during an investigation of the processing and properties of aluminum-cerium alloys produced via casting, extrusion and additive manufacturing. The results show mechanical properties are retained at higher temperatures than other aluminum alloys and show complete recovery of mechanical properties at room temperature when exposed to elevated temperatures as high as 500 °C for 1000 h. Alloys containing cerium also have superior corrosion properties when compared to most aluminum alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Characterization of an aluminum alloy hemispherical shell fabricated via direct metal laser melting

The ability of additive manufacturing to directly fabricate complex shapes provides characterization challenges for part qualification. The orientation of the microstructures produced by these processes will change relative to the surface normal of a complex part. In this work, the microscopy and x-ray tomography of an AlSi10Mg alloy hemispherical shell fabricated using powder bed metal additive manufacturing are used to illustrate some of these challenges. The shell was manufactured using an EOS M280 system in combination with EOS-specified powder and process parameters. The layer-by-layer process of building the shell with the powder bed additive manufacturing approach results in a position-dependent microstructure that continuously changes its orientation relative to the shell surface normal. X-ray tomography was utilized to examine the position-dependent size and distribution of porosity and surface roughness in the 98.6% dense part. Optical and electron microscopy were used to identify global and local position-dependent structures, grain morphologies, chemistry, and precipitate sizes and distributions. The rapid solidification processes within the fusion zone (FZ) after the laser transit results in a small dendrite size. Cell spacings taken from the structure in the middle of the FZ were used with published relationships to estimate a cooling rate of ~9 × 10 5 K/s. Uniformly-distributed, nanoscale Si precipitates were found within the primary α-Al grains. A thin, distinct boundary layer containing larger α-Al grains and extended regions of the nanocrystalline divorced eutectic material surrounds the FZ. Moreover, subtle differences in the composition between the latter layer and the interior of the FZ were noted with scanning transmission electron microscopy (STEM) spectral imaging.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Effects of Post-sintering Annealing on (NdLa)-(FeCo)-B Magnets

A common limitation of La substitutions into (Nd, La) 2 Fe 14 B magnets is the reduction of the anisotropy field (H a ), which decreases magnet coercivity (H cj ). In this study, adding a small amount of Pr-Cu to a La-containing neo magnet may modify the grain boundary (GB), which can help recover a fraction of the degraded H cj . An optimal GB modification requires a carefully designed post-sinter heat treatment, which is the focus of this work on characterizing the effects of multi-step post-sintering annealing on the evolutions of microstructure and magnetic properties. We find that Nd and Cu concentrations at GBs and triple junctions (TJs) increase when the annealing temperatures are lowered. Annealing temperatures of 580°C and 480°C (near rare-earth-rich eutectic temperatures) enabled the development of a thick and continuous GB phase, which helps to magnetically decouple the grains, and, thus, enhance H cj . For the alloy with 25% Nd replaced by La, and with the addition of 7.5 wt.% of Pr 68 Cu 32 as GB modifier, the optimized multi-step post-sinter annealing improved the H cj from 4.8 kOe to 9 kOe.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Microstructural Coarsening Kinetics and Mechanical Property Changes in Long-Term Aged Sn–Pb–Sb Solder Joints

Tin-lead-antimony (50Sn–47Pb–3Sb wt.%) soldered assemblies were mechanically tested approximately 30 years after initial production and found to have solder joints of reduced strength. The microstructure of this solder alloy exhibits a ternary eutectic structure with Sn-rich, Pb-rich, and SnSb phases. Accelerated aging was performed to evaluate solder microstructural coarsening and associated strength of laboratory solder joints to correlate these properties to the “naturally aged” solder joints. Isothermal aging was conducted at room temperature, 55, 70, 100, and 135 °C and aging times that ranged from 0.1 to 365 days. The coarsening kinetics of the Pb-rich phase were determined through optical microscopy and image analysis methods established in previous studies on binary Sn–Pb solder. A kinetic equation was developed with time exponent n of 0.43 and activation energy of 24000 J/mol, suggesting grain boundary diffusion or other fast diffusion pathways controlling the microstructural evolution. Compression testing and Vickers microhardness showed significant strength loss within the first 20–30 days after soldering; then, the microstructure and mechanical properties changed more slowly over long periods of time. Further, by combining accelerated aging data and the microstructure-based kinetics, strength predictions were made that match well with the properties of the actual soldered assemblies naturally aged for 30 years. However, aging at the highest temperature of 135 °C produced anomalous behavior suggesting that extraneous aging mechanisms are active. Therefore, data obtained at this temperature or higher should not be used. Overall, the combined microstructural and mechanical property methods used in this study confirmed that the observed reduction in strength of ~ 30-year-old solder joints can be accounted for by the microstructural coarsening that takes place during long-term solid-state aging.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Stress relaxation cracking susceptibility evaluation in 347H stainless steel welds

Abstract Stress relaxation cracking (SRC) has been reported as a dominant failure mechanism for 347H stainless steel welds at elevated service temperatures, occurring in either the heat-affected zone (HAZ) or fusion zone (FZ). In this study, SRC susceptibility of physically simulated HAZ and cross-welded E347-347H stainless steel welds was studied using a four-step accelerated SRC test with a thermomechanical physical simulator. The stress and temperature range studied represents weld-induced residual stress at 150–600 MPa and post-weld heat treatment temperatures between 800 and 1050 °C. For all temperature conditions, the cross-welded samples failed at a lower critical stress threshold than the simulated HAZ. A finite element model of a 50.8-mm-thick single-V groove weld was used to generate the residual stress maps induced by a 40-pass welding procedure, which in combination with the experimental threshold stress map predicted potential SRC failure locations. Postmortem microstructural evaluations were performed to identify contributing characteristics to SRC. It was found that HAZ samples exhibited a combination of creep void development, secondary cracks with intergranular fracture near grain boundary carbides, and eutectic phases. FZ samples showed brittle fracture with cracks propagating along straight, non-tortuous interdendritic grain boundaries.

42 ENGINEERING↗
DOE OSTI2022

How Cerium and Lanthanum as Coproducts Promote Stable Rare Earth Production and New Alloys

The largest outputs of rare earth mining are the low-value byproducts cerium and lanthanum, which burden rare earth supply chains because they must be separated from more desirable rare earths used in magnet production. Promoting demand for cerium and lanthanum can potentially diversify the economics of rare earth mining and improve supply chain stability for all rare earth elements. A promising avenue for increasing byproduct rare earth element demand is their use in aluminum alloys; an application for cerium and lanthanum offering multiple benefits to manufacturing such as energy reduction and improved throughput. Experimental materials science and economic implications of Al-rare earth element alloys will be discussed. We show that Al–La/Ce alloys have elevated mechanical strength compared to more traditional aluminum alloys, in some formulations can be used without heat treatment, and possess a highly castable eutectic microstructure. This report presents the use of cerium and lanthanum in aluminum alloys as an example of how supply chain focused approaches to technological development can benefit stakeholders at every step in production.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Corrosion in Other Liquid Metals (Li, PbLi, Hg, Sn, Ga)

A wide range of liquid metals have been considered for application in nuclear fission and fusion reactors. Liquid mercury (Hg) was tested as a coolant and working fluid for nuclear fission reactors and as a neutron source target. Liquid lithium and lead lithium eutectic (Li and PbLi) have been extensively studied for fusion reactor designs including plasma facing components (PFCs). Liquid tin and gallium (Sn and Ga) have recently gained attention as alternative PFCs due to their low vapor pressure and chemical stability. To enable successful application of these less common liquid metals, corrosion compatibility with containment materials needs to be investigated. For this purpose, this article reviews corrosion behavior and structural material compatibility, including ferrous alloys, refractory metals, and ceramics, by liquid Li, PbLi, Sn, Ga, and Hg.

Jun, Jiheon↗
DOE OSTI2024

Liquid metal walls

Here, the plasma performance of fusion devices depends strongly on the chosen wall materials. Solid plasma-facing components (PFCs) are predominantly used in present devices, and are the most investigated candidates for fusion designs. High-Z materials such as tungsten (W) are the leading solid PFC material candidates. To date, a material choice that scales to steady-state reactor conditions has not been identified. Moreover, if plasma transient events such as edge-localized modes and disruptions cannot be altogether avoided or sufficiently mitigated, the projected peak heat and particle loads far exceed the power exhaust capabilities of solids. Liquid metal (LM) PFCs represent an intrinsic self-healing boundary that are both resilient to surface damage from transients, and that could handle high steady-state heat and particle fluxes. Flowing LM PFCs can be designed to remove “slag,” the buildup of material erosion due to plasma-material interactions, including charge exchange sputtering in the main chamber. Further, LM offer the prospect to manage hydrogenic species otherwise retained in the PFCs, which is important from a safety and inventory standpoint. The two most promising LMs are lithium (Li) and tin (Sn), although Sn–Li eutectics may be considered. While Sn offers a higher temperature window with low vapor pressure and low hydrogen retention, Li offers the prospect of enhanced energy confinement and higher acceptable core contamination limits, and this section focuses on Li PFCs. An LM PFC development research program developed LM PFC concepts for a nuclear fusion device via engineering design calculations, single-effect experiments, and staged prototypical experiments. A self-consistent design window was identified with liquid Li flow speeds ~5–10 m/s; plasma contamination was negligible for predicted Li evolution rates. While these preconceptual designs hold promise, there is substantial R&D needed to advance the technical readiness levels of LM PFCs for application to fusion power plants.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗