Search NASA⌕ Search

SEARCH · Search NASA

Results for “Electron backscatter diffraction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42

Directed energy deposition of Haynes 282 nickel superalloy

Laser powder directed energy deposition was employed to fabricate Haynes® 282 Ni-based superalloy for high temperature creep testing. Material was heat treated using a single-step aging heat treatment of 800 °C for 4 h. Microstructural analysis was conducted in the as-deposited, solution-annealed, and age-hardened conditions. γ′ precipitates were absent in the as-deposited and annealed condition but formed during aging with an average size of 48.5 ± 12 nm. γ’ denuded zones ranging in thickness from 73 to 469 nm were observed adjacent to an effectively continuous grain boundary carbide film that covered 72.5% of the measured boundary length. The heat-treated material contained a high-volume fraction of TiC carbides ranging in size from 38 to 457 nm. Electron backscatter diffraction showed partial recrystallization, with 77-83% recrystallized area and a heterogeneous grain-size distribution. Creep testing at 750 °C at 300, 320, and 350 MPa revealed significantly inferior performance compared to wrought material, with higher strain rates, earlier tertiary onset, and shorter rupture lives. Fractography shows that failure was dominated by intergranular rupture. Post rupture microstructural analysis results suggest that the creep behavior was primarily governed by the non-equilibrium interface network rather than the bulk γ/γ’ matrix. In conclusion, the findings indicate that achieving wrought-like creep performance necessitates substantial improvements in the additive process, specifically focusing on enhanced homogenization, full recrystallization, and precise control over the morphology and distribution of carbides.

36 - MATERIALS SCIENCE↗

Novel amorphous SiOC dispersion-strengthened austenitic steels.

Here, a novel amorphous silicon oxycarbide dispersion-strengthened (SiOC-DS) austenitic steel has been fabricated via a powder metallurgy process. The microstructure of dispersion particles has been characterized by transmission electron microscopy (TEM) and electron backscatter diffraction (EBSD), revealing that amorphous SiOC nanoparticles with an average particle size of 30 nm were homogeneously distributed in the austenite grains with a sub-micrometer grain size. The high strength and hardness of SiOC-DS may be attributed to grain boundary strengthening, as well as dispersion strengthening via dislocation–particle interactions that were revealed by TEM investigations. In situ ion irradiation experiments showed that amorphous SiOC particles were stable after irradiation of 3.7 dpa, and the SiOC/steel interface can be an effective sink for the annihilation of irradiation defects. The excellent mechanical and irradiation properties of SiOC-DS austenitic steel make it a promising structural material for nuclear applications.

36 MATERIALS SCIENCE↗

Numerical and experimental characterization of twin transmission across grain boundaries along the forward and lateral directions

Pervasive deformation twinning and transmission events across grain boundaries (GBs) affect the strength and failure of hexagonal close-packed (HCP) magnesium. A three-dimensional twin can transmit along the twinning shear direction, (forward), and along the direction perpendicular to both the twinning plane normal and the shear direction, (lateral). For the first time, phase-field calculations and electron backscatter diffraction (EBSD)-based statistical analysis are combined to investigate the effect of the twinned grain boundary characteristics on twin transmission (TT) along the forward and lateral directions. This combined analysis reveals that TT propensity decreases with increasing misorientation angle across the GB for both forward and lateral directions. Also, the TT is more favorable along the lateral than along the forward direction. Twin transmission seems harder across GBs with a misorientation axis closer to the twin -direction than the other directions ( and ). Further, the PF calculations reveal that, at the onset of a transmission process, the crystallography tends to be preserved in the case of lateral transmission, whereas, in the forward transmission case, the transmitted twin punches straight through the GBs and its morphology prevails. Additionally, the EBSD analysis finds that pure forward and lateral transmissions do not occur often, yet reveals a preference for lateral propagation consistent with PF simulations. Further, the local twin transmission configurations observed in the actual material do not correspond to pure tilt or twist GBs, which are most commonly considered as model cases.

36 MATERIALS SCIENCE↗

Solidification and crystallographic texture modeling of laser powder bed fusion Ti-6Al-4V using finite difference-monte carlo method

Laser powder bed fusion (LPBF) additive manufacturing makes near-net-shaped parts with reduced material cost and time, rising as a promising technology to fabricate Ti-6Al-4V, a widely used titanium alloy in aerospace and medical industries. However, LPBF Ti-6Al-4V parts produced with 67° rotation between layers, a scan strategy commonly used to reduce microstructure and property inhomogeneity, have varying grain morphologies and weak crystallographic textures that change depending on processing parameters. Here, this study predicts LPBF Ti-6Al-4V solidification at three energy levels using a finite difference-Monte Carlo method and validates the simulations with large-area electron backscatter diffraction (EBSD) scans. The developed model accurately shows that a <001> texture forms at low energy and a <111> texture occurs at higher energies parallel to the build direction but with a lower strength than the textures observed from EBSD. A validated and well-established method of combining spatial correlation and general spherical harmonics representation of texture is developed to calculate a difference score between simulations and experiments. The quantitative comparison enables effective fine-tuning of nucleation density (N 0 ) input, which shows a nonlinear relationship with increasing energy level. Future improvements in texture prediction code and a more comprehensive study of N 0 with different energy levels will further advance the optimization of LPBF Ti-6Al-4V components. These developments contribute a novel understanding of crystallographic texture formation in LPBF Ti-6Al-4V, the development of robust model validation and calibration pipeline methodologies, and provide a platform for mechanical property prediction and process parameter optimization.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Photoacoustic 3-D imaging of polycrystalline microstructure improved with transverse acoustic waves

Non-invasive fast imaging of grain microstructure of polycrystalline ceria with sub-micrometric spatial resolution is performed via time-domain Brillouin scattering. The propagation of a nanoacoustic pulse is monitored down to 8 µm deep in a 30 × 30 µm2 area. Grains boundaries are reconstructed in three-dimensions via a twostep processing method, relying on the wavelet synchro-squeezed transform and the alpha shape algorithm. Imaging contrast is improved by taking advantage of stronger sensitivity to anisotropy of transverse acoustic waves, compared with longitudinal waves. Utilization of transverse waves in the image processing reveals additional boundaries that are not discerned using longitudinal waves, confirmed by an electron backscattering diffraction pattern. A buried inclined interface between differently oriented grains is identified by monitoring changes in amplitude (phase) of the portion of the signal associated with transverse (longitudinal) waves. Estimates of the inclination angle of this interface prove the sensitivity of our laser ultrasonic method to image inclined boundaries.

36 MATERIALS SCIENCE↗

Conversion of real-world aluminum scrap streams into high-performance Al–Mg–Si–Cu automotive alloys using shear assisted processing and extrusion

The conversion of post-consumer aluminum (Al) scrap into usable Al alloys without adding primary Al is challenging because of excess impurities. In this work, >99% post-consumer Twitch, used beverage cans (UBCs), and remelt scrap ingots (RSIs) were used as feedstock materials. As-cast and solution heat-treated feedstock billets were extruded using Shear Assisted Processing and Extrusion (ShAPE) at ~510°C, followed by press quenching. To explore the development of the microstructure, texture, and underlying mechanisms and how they contribute to the overall strengthening in as-extruded and artificially aged samples, scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD) were used to collect microstructure and texture data. The enhanced strength and ductility were corroborated with the microstructural features and crystallographic texture. Simple shear $\textrm{A}/\bar{\textrm{A}}$, $\textrm{A}_1^*/\textrm{A} _2^*$ texture components along with weak $\textrm{C}$ and $\textrm{B}/\bar{\textrm{B}}$ texture components were formed during extrusion; the texture was strengthened after heat treatment. The refined second-phase particles helped to retain the deformed microstructure and texture. The contributions of dislocation and precipitate strengthening were maximized when billets were solution-heat-treated prior to extrusion. This is attributed to the formation of effective supersaturated solid solutions during the ShAPE process, which precipitate out during the peak age treatment. Overall, the highest yield strength of 305 MPa, ultimate tensile strength of 350 MPa, and elongation of 12% were achieved in artificially aged samples, which are comparable to those of Al 6082-T6.

Al alloy↗

Nondestructive characterization of polycrystalline 3D microstructure with time-domain Brillouin scattering

In this paper, we employ gigahertz frequency ultrasonic waves to non-invasively image grain microstructure in polycrystalline ceria, an important electrolyte material for solid oxide fuel cells. This technique, termed time domain Brillouin scattering (TDBS), is a pump-probe technique that launches and monitors ultrasonics waves as they propagate from the surface into the depth of a sample. We demonstrate the capability of TDBS to image surface and subsurface grain structure by measuring mode and depth dependent velocity of the ultrasonic wave. A neural network tool is adopted to determine grain orientation from measured velocities. The TDBS results compare closely with electron backscatter diffraction (EBSD) measurements. This work expands the application of picosecond ultrasonics to three-dimensional imaging and offers a new route for the nondestructive microstructure characterization and in situ examination of polycrystalline materials.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Microstructural evolution of an aluminide coating on alloy 625 during wet air exposure at 900 °C and 1000 °C

The microstructural changes of the aluminized alloy 625 during cyclic oxidation in air + 6% H 2 O at 900 °C and 1000 °C were analyzed using optical metallography (OM), scanning electron microscopy (SEM) with energy and wave length dispersive X-ray analysis (EDX/WDX) as well as electron backscatter diffraction (EBSD). An in-house developed thermodynamic-kinetic procedure was employed to predict the microstructural evolution of aluminized alloy 625 during high temperature exposure by considering simultaneously occurring surface oxidation and interdiffusion processes. Because of the lack of mobility data for the relevant alloying elements in the σ-phase, assumptions for the mobilities were made based on the value of the mobilities in α-Cr. Despite these assumptions, the calculated results were found to be in good agreement with experimental observations. The complete depletion of β-NiAl in the coating observed during exposure at 1000 °C was correctly predicted by the model. The model was also able to infer dissolution of the precipitate phases α-Cr and σ in the interdiffusion zone during exposures at 900 °C and 1000 °C. The model was yet unable to predict the formation of the μ-phase in the alloy after 1000 h of exposure at 1000 °C. The developed modelling method offers the potential to predict microstructural changes of aluminized nickel base alloys thus reducing cost and time consuming experimental efforts.

36 MATERIALS SCIENCE↗

Effect of post-deposition heat treatment on microstructure and mechanical properties of NASA HR-1 cold spray coatings

The primary goal of this work was to examine the impact of heat treatment on the evolution of microstructure and mechanical properties of NASA HR-1 cold spray coatings. Coatings were produced employing a high pressure cold spray system using N2 and He process gases and the effect of process gas and deposition temperature on the microstructure and mechanical properties of the coatings was examined. Microstructural characterization was performed using optical microscopy, scanning electron microscopy, micro X-ray computed tomography, and electron backscatter diffraction. NASA HR-1 coatings produced with He process gas exhibited improved plastic deformation and resulted in the lowest porosity compared to those deposited with N2 process gas. All coatings showed brittle failure with limited ductility in the as-deposited condition. Heat treatment of the NASA HR-1 cold spray coatings was performed at 550°C and 950°C for 1 h to improve the mechanical strength of the coatings. Heat treatment improved the particle bonding and enhanced the mechanical properties of the cold spray coatings. Heat treatment performed at 550°C resulted in higher mechanical strength of coatings, whereas the heat treatment performed at 950°C resulted in recrystallized microstructure and improved ductility of the coatings. However, heat treatment at 950°C resulted in forming the Eta (η) phase and Ni-Ti intermetallics in all the NASA HR-1 cold spray coatings. Here, the overall results suggest that using He as process gas contributed to reduced porosity and enhanced mechanical properties of the cold spray coatings.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Elasto-viscoplastic fast Fourier transform modeling framework for assessing microstructural effects on stress intensity factors characterizing fracture toughness

A large-strain elasto-viscoplastic fast Fourier transform (LS-EVPFFT) model with non-periodic (NP) velocity-based boundary conditions is adapted to simulate the sensitivity of stress intensity factors on microstructure for 304L stainless steel. The material was characterized via electron backscattered diffraction (EBSD) serial-sectioning to obtain a measured 3-D microstructural cell to perform simulations. The NP-LS-EVPFFT model, including the simulation setup and boundary conditions, was verified using a crystal plasticity finite element (CPFE) model. To this end, the generation of meshes of notched specimens was developed, which involved creating Python scripts for mesh “cutting” in Abaqus, and Sculpt scripts in Cubit for meshing of the measured microstructural cell processed with DREAM.3D. The complexity of the mesh preparation highlighted the advantages of the FFT-based model, which circumvents the mesh generation process. Given the efficiency of the FFT-based model, statistical distribution of stress intensity factors in function of crystal orientation at the crack tip, grain structure, and crystallographic texture surrounding the crack tip were predicted. Further, the distributions reveal about 10% variation of stress intensity factors with microstructure with the most significant sensitivity found to be the crystal orientation at the crack tip. The methodology developed in this work is discussed as a practical simulation tool for predicting the sensitivity of stress intensity factors on microstructural variability in metallic materials.

36 MATERIALS SCIENCE↗

Correlating results from high resolution EBSD with TEM- and ECCI-based dislocation microscopy: Approaching single dislocation sensitivity via noise reduction

High resolution electron backscatter diffraction (HREBSD), an SEM-based diffraction technique, may be used to measure the lattice distortion of a crystalline material and to infer the geometrically necessary dislocation content. Uncertainty in the image correlation process used to compare diffraction patterns leads to an uneven distribution of measurement noise in terms of the lattice distortion, which results in erroneous identification of dislocation type and density. This work presents a method of reducing noise in HREBSD dislocation measurements by removing the effect of the most problematic components of the measured distortion. The method is then validated by comparing with TEM analysis of dislocation pile-ups near a twin boundary in austenitic stainless steel and with ECCI analysis near a nano-indentation on a tantalum oligocrystal. Finally, the HREBSD dislocation microscopy technique is able to resolve individual dislocations visible in TEM and ECCI and correctly identify their Burgers vectors.

36 MATERIALS SCIENCE↗

Extracting Grain Orientations from EBSD Patterns of Polycrystalline Materials Using Convolutional Neural Networks

Abstract We present a deep learning approach to the indexing of electron backscatter diffraction (EBSD) patterns. We design and implement a deep convolutional neural network architecture to predict crystal orientation from the EBSD patterns. We design a differentiable approximation to the disorientation function between the predicted crystal orientation and the ground truth; the deep learning model optimizes for the mean disorientation error between the predicted crystal orientation and the ground truth using stochastic gradient descent. The deep learning model is trained using 374,852 EBSD patterns of polycrystalline nickel from simulation and evaluated using 1,000 experimental EBSD patterns of polycrystalline nickel. The deep learning model results in a mean disorientation error of 0.548° compared to 0.652° using dictionary based indexing.

Materials Science↗

Cluster Analysis of Combined EDS and EBSD Data to Solve Ambiguous Phase Identifications

A common problem in analytical scanning electron microscopy (SEM) using electron backscatter diffraction (EBSD) is the differentiation of phases with distinct chemistry but the same or very similar crystal structure. X-ray energy dispersive spectroscopy (EDS) is useful to help differentiate these phases of similar crystal structures but different elemental makeups. However, open, automated, and unbiased methods of differentiating phases of similar EBSD responses based on their EDS response are lacking. This paper describes a simple data analytics-based method, using a combination of singular value decomposition and cluster analysis, to merge simultaneously acquired EDS + EBSD information and automatically determine phases from both their crystal and elemental data. I use hexagonal TiB 2 ceramic contaminated with multiple crystallographically ambiguous but chemically distinct cubic phases to illustrate the method. Code, in the form of a Python 3 Jupyter Notebook, and the necessary data to replicate the analysis are provided as Supplementary material.

47 OTHER INSTRUMENTATION↗

Argon Milling of Bulk and Post-FIB Specimens for Multi-Length Scale Analyses by EBSD, TEM, and APT under Controlled Environments

Correlative investigations involve structural characterization by transmission electron microscopy (TEM) combined with compositional analysis by atom probe tomography (APT) using the same specimen. A critical component of successful correlative analyses is specimen preparation; probing individual atoms requires a surface and subsurface with minimal defects, beginning with the bulk material through to the prepared specimen for TEM or APT analysis. Our previous work showed that low-energy concentrated ion beam Ar ion milling improves TEM [1] and APT [2,3] specimen quality by removing surface oxides and Ga damage caused by focused ion beam (FIB) preparation. Further enhancement in specimen quality of APT specimens is achieved in the established workflow under controlled environments, as shown in [4]. In this work, we present specimen preparation using Ar ion milling techniques not only for the APT specimen, but also the bulk sample for subsequent multi-length scale analyses by electron backscatter diffraction (EBSD), TEM, and APT under controlled environments. The removal of surface damage and oxidation, which is crucial for probing atomic layer specimens by broad and concentrated Ar ion beam milling techniques under controlled environments, is highlighted.

36 MATERIALS SCIENCE↗

Influence of the Laser Scanning Rate on the Structure of Rotating Lattice Single Crystal Lines

Localized controlled heating of glass with a continuous wave laser has introduced the possibility of engineering the lattice of recently discovered rotating lattice single (RLS) crystals and thus obtaining novel metamaterials. On this account, we report the role of the laser scanning speed on the lattice structure of a model system: Sb 2 S 3 straight RLS crystal lines created in a 16SbI 3 -84Sb 2 S 3 glass. The electron backscatter diffraction analysis shows that above a critical laser scanning speed the lattice rotates along the direction of scanning, the rate of lattice rotation is relatively insensitive to scanning speed, and the growth front is symmetric. In contrast, for laser scanning speeds below this critical value, the rate and direction of lattice rotation are strongly affected by the speed. Further, the growth front becomes asymmetric, which promotes the formation of new grains misoriented by ≤10°. These observations are reported on in terms of the relative dominance of the temperature gradient from laser scanning vis-á-vis the intrinsic preferred crystallographic direction of crystal growth. In addition to providing guidelines for fabricating the RLS crystal of the desired rate of the lattice rotation, new insight is gained for the mechanism of plumose formation in spherulitic crystals.

36 MATERIALS SCIENCE↗

Laser-Induced Enhancement of Acoustic Mode Quality Factor Revealed by Correlated Single-Particle Optical and Electron Microscopy

Acoustic modes in plasmonic nanostructures provide fundamental insights into their optomechanical behavior at the nanoscale, enabling emerging applications in plasmon-enhanced optomechanics, ultrasensitive sensing, and nanoscale energy transduction. Here we explore the modulation of acoustic phonon dynamics in lithographically fabricated gold nanodisks via laser-induced photothermal annealing. Using a correlated approach that utilizes both single-particle transient extinction spectroscopy and advanced electron microscopy, we directly link nanoscale structural transformations to changes in mechanical properties as probed through the coherence of the excited acoustic modes. Specifically, ultrafast pump–probe microscopy reveals an enhancement in the acoustic mode quality factor of annealed gold nanodisks, indicative of reduced damping and improved vibrational coherence. Structural characterization via scanning electron microscopy and electron backscatter diffraction confirms that photoinduced annealing results in smoother surface morphology and overall enhanced crystallinity. The improved crystalline order reduces defect and crystal boundary scattering, which we suggest as the reason underlying the lower quality factor before annealing. Furthermore, these findings demonstrate that targeted structural engineering at the nanoscale offers a powerful strategy for optimizing the optomechanical performance of plasmonic nanostructures, with broad implications for the design of next-generation nanophotonic and optomechanical systems.

Annealing (metallurgy)↗

Epitaxial Electrodeposition of Fe with Controlled In-Plane Variants for a Reversible Metal Anode in an Aqueous Electrolyte

The development of reversible metal anodes is a key challenge for advancing aqueous battery technologies, particularly for scalable and safe stationary energy storage applications. Here, in this study, we demonstrate a strategy to realize epitaxial electrodeposition of iron (Fe) on single-crystal copper (Cu) substrates in aqueous electrolytes. We compare the electrodeposition behavior of Fe on polycrystalline and single-crystalline Cu substrates, revealing that the latter enables highly uniform, dense, and crystallographically aligned Fe growth. Comprehensive electron backscatter diffraction (EBSD) and X-ray diffraction (XRD) analysis confirms the formation of Fe with specific out-of-plane and in-plane orientations, including well-defined rotational variants. Our findings highlight that epitaxial electrodeposition of Fe can suppress dendritic growth and significantly enhance Coulombic efficiency during plating/stripping cycles. This approach bridges fundamental crystallography with practical electrochemical performance, providing a pathway toward high-efficiency aqueous batteries utilizing Earth-abundant materials.

aqueous battery↗

A quantitative comparison of the fingerprint of twinned microstructures through surface and three-dimensional techniques

Assessing the fingerprint of a material’s microstructure is key for supporting materials design. With the emergence of a wide range of 3D characterization techniques, it is critical to understand the main differences in fingerprints reconstructed from 2D and 3D datasets. To this end, we introduce a graph-based microstructure reconstruction framework that enables structural comparisons of twin domain networks in high purity Ti using 3D and 2D electron backscatter diffraction. Insights into the structure of the twin networks are facilitated by combining statistical analysis of twin crystallography with visual and graphical analysis of the novel graph abstractions of the twins. We demonstrate that compared to 3D reconstructions, conventional 2D views of twinning miss key aspects of the microstructure including the high interconnectivity of domains into networks that span the full reconstruction volume. The reduced cross-grain and in-grain twin connectivity typically observed in 2D has notable implications on our understanding of how twinning mediates the plastic response of microstructures and how twin networks evolve. It is thus clear that 3D characterization is critical for accurately inferring both twin network morphologies as well as the key unit processes facilitating network formation.

36 MATERIALS SCIENCE↗