Search NASA⌕ Search

SEARCH · Search NASA

Results for “Fast Reactor Fuel”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42

MESOSCALE THERMAL TRANSPORT MEASUREMENTS OF MULTI-PHASE AND POROUS NUCLEAR FUELS USING A SQUARE-WAVE PULSE THERMOREFLECTANCE TECHNIQUE

The safe and efficient operation of nuclear reactors require accurate knowledge of peak temperatures in the fuel assemblies. The temperature profiles are governed by the thermal transport properties of the fuel, namely the thermal conductivities (k) and thermal diffusivities (D). These values can be very difficult to measure as they are known to vary considerably from the measured bulk values of the fresh fuel, and quickly degrade with increasing burnup [1 -3] . Laser-based techniques have been effectively used for non-destructive and non-contact thermal transport measurements of a wide variety of materials, including nuclear materials [4-6] that would otherwise prove too hazardous or difficult to measure otherwise. In this study, a new thermoreflectance technique known as square-pulse transient thermoreflectance (SPTR) is described and used to determine the mesoscale thermal diffusivity of both uranium sesquisilicide (U3Si2) and uranium nitride (UN) phases in a composite fuel with micron level spatial resolution [7]. This technique employs a rapid train of square-wave pulses from an excitation laser to create a periodic heat flux on a gold coated sample surface. Surface adsorption results in transient film temperatures and hence rapid fluctuations in thermoreflectance that can be measured via a detection laser coupled with a digital oscilloscope. The lasers are coaxially focused on the sample surface, allowing for a sample measurement area of a single convolved laser spot size (~2 µm). A sensitivity analysis was conducted to identify key measurement parameters of this technique using reference materials with a range of thermal conductivities comparable to those of both ceramic, composite, and metal nuclear fuel types (1.4 – 27.2 W/m-K). The reference materials were measured using the new technique as well as a spatial-domain thermoreflectance technique (SDTR) previously reported for a comparison [8]. Additionally, measurements of several U3Si2 and UN phase regions of a polished UN/U3Si2 (70/30 vol.%) sample were taken, and the resulting calculated D values are reported, with both techniques showing excellent agreement between samples. This technique was used to scan a multiphase region at 5 micron increments to generate a local diffusivity map, demonstrating the utility of the techniques for measuring thermal transport properties in specimens with precipitates and secondary phases. Furthermore, the technique is currently being applied to measure thermal properties of Fast Flux Test Reactor (FFTR) irradiated metal fuel specimens whose porous microstructure make it very difficult to measure using other techniques. Comparison of the local scale measurements are compared with the pre-irradiated fuel samples to show the degradation of thermal transport in fuels due to pores from fission gas bubbles and other irradiation induced defects.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Preparation of Prototypic Irradiated Hydrided-Zircaloy Cladding for UFDC Programs

The DOE Used Fuel Disposition Campaign (UFDC) has tasked ORNL to investigate the behavior of light-water-reactor fuel cladding material performance related to extended storage and transportation of used fuel. Fast neutron irradiation of pre-hydrided zirconium-alloy cladding in the High Flux Isotope Reactor (HFIR) at elevated temperatures has been used to simulate the effects of high burnup on used fuel cladding for use in understanding the materials properties relevant to very long-term storage (VLTS) and subsequent transportation. The irradiated pre-hydrided metallic materials will generate baseline data to benchmark hot-cell testing of high-burnup used fuel cladding; and, more importantly, samples free of alpha contamination can be provided to the researchers who do not have hot cell facilities to handle highly contaminated high-burnup used fuel cladding to support their research projects for the UFDC. In order to accomplish this research, ORNL has produced unirradiated zirconium-based cladding tubes with a certain hydrogen concentration. Two capsules (HYCD-1 and HYCD-2) containing hydrided zirconium-based samples, 9.50 mm (0.374 in) in diameter, were inserted in HFIR for neutron irradiation. HYCD-1 was removed after Cycle 440B and HYCD-2 after Cycle 442. This paper will describe the general HYCD experiment configuration, achieved temperatures, and temperature gradients within the cladding, and current results of the PIE of the irradiated hydrided cladding samples.

prototypic irradiated zircaloy cladding unirradiat↗

Progress Report on SFR Metallic Fuel Data Qualification

This report summarizes the progress of SFR metallic fuel qualification related activities, which are focused on providing quality assurance relevant information applicable to experiments irradiated during the Integral Fast Reactor (IFR) program. An overview of the metallic fuel performance data and the associated databases, including the EBR-II Fuels Irradiation & Physics Database (FIPD), Out-of-Pile Transient Database (OPTD), and TREAT Experimental Relational Database (TREXR) is included. The legacy data in the databases, including as-built, post-irradiation examination (PIE), operating parameters, and out-of-pile experiment post-test data are introduced. The SFR metallic fuel Quality Assurance Program Plan (QAPP) and its implementation to qualify these legacy data is described in detail. Important PIE data QA documents and the specifications of seven types of PIE measurements (contact profilometry, laser profilometry, neutron radiography, gamma scan, fission gas release fission gas chemistry, and metallography) are provided. Examples of the implementation of the QAPP to qualify each of those types of PIE data are provided.

Mo, Kun [Argonne National Laboratory (ANL), Argonn↗

Analysis of fuel cycle strategies and U.S. transition scenarios

The nuclear fuel cycle Evaluation and Screening (E&S) study that was completed in October 2014 [1] enabled the identification of four fuel cycle groups that are considered most promising based on a set of nine evaluation criteria: (a) six benefit criteria of Nuclear Waste Management, Proliferation Risk, Nuclear Material Security Risk, Safety, Environmental Impact, Resource Utilization, and (b) three challenge criteria of Development and Deployment Risk, Institutional Issues, Financial Risk and Economics. The E&S study was conducted at a level of analysis that is "technology- neutral," that is, without consideration of specific technologies, but using the fundamental physics characteristics of each part of the fuel cycle. The study focused on the fuel cycle performance benefits at the fuel cycle equilibrium state, with only limited consideration of transition and deployment impacts. Common characteristics of the four most promising fuel cycle options include continuous recycle of all U/Pu or U/TRU, the use of fast-spectrum reactors, and no use of uranium enrichment once fuel cycle equilibrium has been established. The high-level wastes are mainly from processing of irradiated fuel, and there would be no disposal of any spent fuel. Building on the findings of the E&S study, additional studies have been conducted in the last two years following the information exchange meeting, the 13th IEMPT, which was held in Seoul, the Republic of Korea in 2014. Insights are presented from the recent studies on the benefits and challenges of recycling minor actinides, and transition considerations to some of the most promising fuel cycle options.

Wigeland, Roald↗

TRIPOLI-4 criticality calculations for MOX fuelled SNEAK 7A and 7B fast critical assemblies

A prototype Generation IV fast neutron reactor is under design and development in France. The MOX fuel will be introduced into this self-generating core in order to demonstrate low net plutonium production. To support the TRIPOLI-4 Monte Carlo transport code in criticality calculations of fast reactors, the effective delayed neutron fraction {beta}eff estimation and the Probability Tables (PT) option to treat the unresolved resonance region of cross-sections are two essentials. In this study, TRIPOLI-4 calculations have been made using current nuclear data libraries JEFF-3.1.1 and ENDF/B-VII.0 to benchmark the reactor physics parameters of the MOX fuelled SNEAK 7A and 7B fast critical assemblies. TRIPOLI-4 calculated K{sub eff} and {beta}eff of the homogeneous R-Z models and the 3D multi-cell models have been validated against the measured ones. The impact of the PT option on K{sub eff} is 340 {+-} 10 pcm for SNEAK 7A core and 410 {+-} 12 pcm for 7B. Four-group spectra and energy spectral indices, f8/f5, f9/f5, and c8/f5 in the two SNEAK cores have also been calculated with the TRIPOLI-4 mesh tally. Calculated spectrum-hardening index f8/f5 is 0.0418 for SNEAK 7A and 0.0315 for 7B. From this study the SNEAK 3D models have been verified for the next revision of IRPhE (International Handbook of Evaluated Reactor Physics Benchmark Experiments). (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

History and status of spent fuel treatment at the INL Fuel Conditioning Facility

Experimental Breeder Reactor II (EBR-II) had an illustrious operational history from 1964 to 1994 as one of the first sodium-cooled fast reactors to use sodium-bonded metallic driver fuels and blankets. EBR-II was a testbed for fuel development and reactor design principles. Following shutdown, it was decided to use electrometallurgical methods to treat the spent fuel and blanket materials for final disposition. Here, this paper provides a brief history of U.S. liquid metal cooled reactor development with emphasis on EBR-II, and a technical description of the electrometallurgical methods.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Fuel Cycle Research & Development, Technical Monthly - February 2012

Topics discussed in this monthly report are: (1) MPACT Campaign management and integration; (2) Accounting and control technologies - microcalorimetry, electrochemical sensor, fast neutron multiplicity analysis, lead slowing down spectrometer; (3) MPACT analysis tools - modeling and simulation for analysis of safeguards performance (electrochemical), material control including process monitoring (pattern recognition, sensors), sensor for measuring density and depth of molten electrolyte, MPACT system integration and technical support.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Complete Survey of Fuel Candidates for Microreactor Purposes

This report summarizes various fuel types that may be applicable to several microreactor concepts, which are defined as (1) very high temperature reactors (VHTR), (2) sodium fast reactors (SFR), (3) system for nuclear auxiliary power (SNAP) reactors, (4) gas fast reactors (GFR), and (5) molten salt reactors (MSR). The fuel systems that were assessed include: uranium mononitride (UN), uranium monocarbide (UC), uranium dioxide (UO 2 ), uranium oxycarbide (UCO) Tristructural Isotropic (TRISO), UN TRISO, mixed oxide (MOX), metallic fuels, and metal hydrides. While UCO TRISO has undergone significant testing through the advanced gas reactor (AGR) program, the very high cost necessitates consideration of other fuel types. UN and UC were identified as fuels that should receive further investigation due to their thermophysical and mechanical properties. Minimal irradiation performance data shows that these fuels are good candidate fuels for microreactors.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Specification of FIPD Fission Gas Chemistry Data

The current FIPD library contains two main sets of fission gas chemistry data. The first set is data collected during the Integral Fast Reactor (IFR) program from 1984 to 1994, using a gas mass spectrometry system located in the Analytical Laboratory (AL) at Argonne National Laboratory-West (Argonne-West). Throughout this period, numerous fission gas release and chemistry datasets were gathered from a variety of metallic fuel pins. The fission gas was sampled by the Gas Assay, Sample and Recharge (GASR) System in the Hot Fuel Examination Facility (HFEF) and transferred to the AL to perform gas composition and isotopic abundance analysis. The second set is data collected after the IFR program. The fission gas samples were also collected by the GASR system at the HFEF, but analyzed using a similar gas mass spectrometer located in Pacific Northwest National Laboratory (PNNL). Many fuel pins irradiated in Experimental Breeder Reactor II (EBR-II) and the Fast Flux Test Facility (FFTF) were measured, including the fuel pins for the MFF series of experiments, designed to qualify metal fuel for use as driver fuel in the FFTF and X496 experiment. For either set of data, fission gas was sampled with the gas sampling line in GASR using sample bottles after the capsule/element volume has been determined and the system is still full of radioactive gas. The sample bottles were then transferred to the sample packaging cylinder or an approved storage location pending transfer to the AL or prepared for shipment to another laboratory (such as PNNL) for analysis of the collected gas as directed on the GASR data form, other approved form. The receiving laboratories (AL or PNNL) required their Analytical Service Request form to be completed prior to sample transfer. Typical sample transfer processes were initiated at HFEF by the principal or process engineer. The laboratories performing the analyses (AL or PNNL) use the sample bottle numbers as well as a sample number produced by the respective laboratory. HFEF and the responsible experimenter tracked the sample using the analysis number, the gas bottle number, and the fuel pin number.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Optimized, Competitive Supercritical-CO2 Cycle GFR for Gen IV Service

An overall plant design was developed for a gas-cooled fast reactor employing a direct supercritical Brayton power conversion system. The most important findings were that (1) the concept could be capital-cost competitive, but startup fuel cycle costs are penalized by the low core power density, specified in large part to satisfy the goal of significatn post-accident passive natural convection cooling; (2) active decay heat removal is preferable as the first line of defense, with passive performance in a backup role; (3) an innovative tube-in-duct fuel assembly, vented to the primpary coolant, appears to be practicable; and (4) use of the S-Co2 GFR to support hydrogen production is a synergistic application, since sufficient energy can be recuperated from the product H2 and 02 to allow the electrolysis cell to run 250 C hotter than the reactor coolant, and the water boilers can be used for reactor decay heat removal. Increasing core poer density is identified as the top priority for future work on GFRs of this type.

08 HYDROGEN↗

Evaluation of Heterogeneous Options: Effects of MgO versus UO2 Matrix Selection for Minor Actinide Targets in a Sodium Fast Reactor

The primary focus of this work was to compare MgO with UO2 as target matrix material options for burning minor actinides in a transmutation target within a sodium fast reactor. This analysis compared the transmutation performance of target assemblies having UO2 matrix to those having specifically MgO inert matrix.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

The Fuel Motion Monitoring System at TREAT - Current Status and Future Plans

An important component of the United States Nuclear Fuel Safety Transient Testing Program, the Fuel Motion Monitoring System (FMMS) at Idaho National Laboratory's Transient Reactor Test Facility (TREAT) is fast-neutron hodoscope capable of imaging the location, movement, and relocation of nuclear fuel experiments under simulated transient accident conditions. The FMMS was refurbished in parallel with the TREAT restart program starting in 2014, restoring 96-channels of fast-neutron detection. Since returning to operation in 2017 the FMMS has supported many fuel safety experiments supporting accident tolerant fuel development, light-water reactor safety, space thermal nuclear propulsion fuel development, and advanced reactor research and development. In Phase 2 of the FMMS restoration. work is now under way to expand the FMMS' field-of-view by adding an additional 96 channels of fast neutron detectors to the system's hodoscope, along with an expanded data acquisition system and associated transient timing electronics. An overview of the FMSS system and its fast-neutron detectors will be presented along with examples of current FMMS imaging performance and associated information.

46 - INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AN↗

Review Paper: Review of Instrumentation for Irradiation Testing of Nuclear Fuels and Materials

Over 50 years of nuclear fuels and materials irradiation testing has led to many countries developing significant improvements in instrumentation to monitor physical parameters and to control the test conditions in material test reactors (MTRs). Recently, there is increased interest to irradiate new materials and reactor fuels for advanced pressurized water reactors and Gen-IV reactor systems, such as sodium-cooled fast reactors, very high temperature reactors, supercritical water-cooled reactors, and gas-cooled fast reactors. This review paper documents the current state of instrumentation technologies in MTRs in the world and summarizes ongoing research efforts to deploy new sensors. As described in this paper, a wide range of sensors is available to measure key parameters of interest during fuels and materials irradiations in MTRs. Ongoing development efforts focus on providing MTR users a wider range of parameter measurements with smaller, higher accuracy sensors.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Corrosion property of 9Cr-ODS steel in nitric acid solution for spent nuclear fuel reprocessing

Corrosion tests of oxide dispersion strengthened with 9% Cr (9Cr-ODS) steel, which is one of the desirable materials for cladding tube of sodium-cooled fast reactors, in pure nitric acid solution, spent FBR fuel solution, and its simulated solution were performed to understand the corrosion behavior in a spent nuclear fuel reprocessing. In this study, the 9Cr-ODS steel with lower effective chromium content was evaluated to understand the corrosion behavior conservatively. As results, the tube-type specimens of the 9Cr-ODS steels suffered severe weight loss owing to active dissolution at the beginning of the immersion test in pure nitric acid solution in the range from 1 to 3.5 M. In contrast, the weight loss was decreased and they showed a stable corrosion in the higher nitric acid concentration, the dissolved FBR fuel solution, and its simulated solution by passivation. The corrosion rates of the 9Cr-ODS steel in the dissolved FBR fuel solution and its simulated solution were 1-2 mm/y and showed good agreement with each other. The passivation was caused by the shift of corrosion potential to noble side owing to increase in nitric acid concentration or oxidative ions in the dissolved FBR fuel solution and the simulated spent fuel solution. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Promises and Challenges of Thorium Implementation for Transuranic Transmutation - 13550

This paper focuses on the challenges of implementing a thorium fuel cycle for recycle and transmutation of long-lived actinide components from used nuclear fuel. A multi-stage reactor system is proposed; the first stage consists of current UO{sub 2} once-through LWRs supplying transuranic isotopes that are continuously recycled and burned in second stage reactors in either a uranium (U) or thorium (Th) carrier. The second stage reactors considered for the analysis are Reduced Moderation Pressurized Water Reactors (RMPWRs), reconfigured from current PWR core designs, and Fast Reactors (FRs) with a burner core design. While both RMPWRs and FRs can in principle be employed, each reactor and associated technology has pros and cons. FRs have unmatched flexibility and transmutation efficiency. RMPWRs have higher fuel manufacturing and reprocessing requirements, but may represent a cheaper solution and the opportunity for a shorter time to licensing and deployment. All options require substantial developments in manufacturing, due to the high radiation field, and reprocessing, due to the very high actinide recovery ratio to elicit the claimed radiotoxicity reduction. Th reduces the number of transmutation reactors, and is required to enable a viable RMPWR design, but presents additional challenges on manufacturing and reprocessing. The tradeoff between the various options does not make the choice obvious. Moreover, without an overarching supporting policy in place, the costly and challenging technologies required inherently discourage industrialization of any transmutation scheme, regardless of the adoption of U or Th. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Reactor-Based Management of Used Nuclear Fuel: Assessment of Major Options

This paper discusses the current status of the ongoing Advanced Fuel Cycle Initiative (AFCI) program in the U.S. Department of Energy that is investigating the potential for using the processing and recycling of used nuclear fuel to improve radioactive waste management, including used fuel. A key element of the strategies is to use nuclear reactors for further irradiation of recovered chemical elements to transmute certain long-lived highly-radioactive isotopes into less hazardous isotopes. Both thermal and fast neutron spectrum reactors are being studied as part of integrated nuclear energy systems where separations, transmutation, and disposal are considered. Radiotoxicity is being used as one of the metrics for estimating the hazard of used fuel and the processing of wastes resulting from separations and recycle-fuel fabrication. Decay heat from the used fuel and/or wastes destined for disposal is used as a metric for use of a geologic repository. Results to date indicate that the most promising options appear to be those using fast reactors in a repeated recycle mode to limit buildup of higher actinides, since the transuranic elements are a key contributor to the radiotoxicity and decay heat. Using such an approach, there could be much lower environmental impact from the high-level waste as compared to direct disposal of the used fuel, but there would likely be greater generation of low-level wastes that will also require disposal. An additional potential waste management benefit is having the ability to tailor waste forms and contents to one or more targeted disposal environments (i.e., to be able to put waste in environments best-suited for the waste contents and forms).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Sensitivity and Uncertainty of the IFR-1 BISON Benchmark

The fuel performance code BISON is being used to evaluate metallic fuel for a new fast-spectrum test reactor called the Versatile Test Reactor, which is being considered by the US Department of Energy. To quantify the accuracy of BISON predictions, researchers at Oak Ridge National Laboratory have been developing a series of benchmarks based on legacy metallic fuel experiments. As part of this effort, the sensitivity of BISON predictions to variations in model inputs and the uncertainties associated with BISON predictions must be established. This report summarizes efforts to perform a comprehensive sensitivity analysis (SA) and uncertainty quantification (UQ) on a benchmark based on the IFR-1 experiment. For the SA, at least one input was chosen from every BISON model and physics module used in the benchmark. The inputs were varied individually in a series of BISON simulations. The resulting variations in benchmark predictions were normalized to calculate sensitivities. The strongest sensitivities were identified and used to inform input selections for the UQ. The UQ was performed using the Monte Carlo UQ method. A literature review was conducted to estimate uncertainty distributions for the selected inputs, and values were sampled randomly from each distribution in a series of BISON simulations. Variations in the benchmark predictions were used to estimate uncertainty distributions and confidence intervals. It was found that nearly 100% of benchmark predictions matched the corresponding legacy values within the confidence intervals. However, this is at least partially because of the wide confidence intervals associated with the benchmark predictions. The uncertainty contributions of assumptions in the benchmark, experimental uncertainties, and BISON models were quantified. Some analysis was performed to identify inputs that contributed to the uncertainties. Finally, recommendations are made for future benchmark development and future BISON development.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Effect of Welding Processes on the Microstructure, Mechanical Properties and Residual Stresses of Plain 9Cr-1Mo Steel Weld Joints

9Cr-1Mo steel designated as P9 is widely used in the construction of power plants and high-temperature applications. It is chosen for fabricating hexcan fuel subassembly wrapper components of fast breeder reactors. Arc welding processes are generally used for fabricating 9Cr-1Mo steel weld joints. A-TIG welding process is increasingly being adopted by the industries. In the present study, shielded metal arc (SMA), tungsten inert gas (TIG) and A-TIG welding processes are used for fabricating the 9Cr-1Mo steel weld joints of 10 mm thickness. Effect of the above welding processes on the microstructure evolution, mechanical properties and residual stresses of the weld joints has been studied in detail. All the three weld joints exhibited comparable strength and ductility values. 9Cr-1Mo steel weld joint fabricated by SMAW process exhibited lower impact toughness values caused by coarser grain size and inclusions. 9Cr-1Mo steel weld joint fabricated by TIG welding exhibited higher toughness due to finer grain size, while the weld joint fabricated by A-TIG welding process exhibited adequate toughness values. SMA steel weld joint exhibited compressive residual stresses in the weld metal and HAZ, while TIG and A-TIG weld joint exhibited tensile residual stresses in the weld metal and HAZ.

36 MATERIALS SCIENCE↗