Search NASA⌕ Search

SEARCH · Search NASA

Results for “GUIDANCE SENSOR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42

Guidance, Navigation, and Control System Design in a Mass Reduction Exercise

Early Orion GN&C system designs optimized for robustness, simplicity, and utilization of commercially available components. During the System Definition Review (SDR), all subsystems on Orion were asked to re-optimize with component mass and steady state power as primary design metrics. The objective was to create a mass reserve in the Orion point of departure vehicle design prior to beginning the PDR analysis cycle. The Orion GN&C subsystem team transitioned from a philosophy of absolute 2 fault tolerance for crew safety and 1 fault tolerance for mission success to an approach of 1 fault tolerance for crew safety and risk based redundancy to meet probability allocations of loss of mission and loss of crew. This paper will discuss the analyses, rationale, and end results of this activity regarding Orion navigation sensor hardware, control effectors, and trajectory design.

Crain, Timothy↗

Attitude and articulation control for CRAF/Cassini

The Comet Rendezvous/Asteroid Flyby (CRAF) and Cassini planetary missions provide exciting pointing and control challenges. The mission and science objectives, and an attitude and articulation control concept designed to meet these challenges, are described. CRAF/Cassini mission characteristics which drive pointing and control include: close range flybys of asteroids and icy satellites; Huygens probe guidance and communication; Saturn orbit insertion; comet rendezvous and orbit insertion; closed loop target tracking from a comet orbit perturbed by gas and dust pressure; fine spacecraft pointing for Titan radar mapping and Earth communications; requirements for autonomous failure detection; isolation; recovery; and 13.5 year lifetime. The philosophy and approach chosen to meet these challenges and the overall control architecture are addressed, including operational and autonomous safe modes. Critical functions are highlighted, such as charge coupled device imaging of stars and extended bodies which provide references for inertial and target referenced pointing respectively. Tradeoffs and rationale for the selection and location of sensors and actuators are reviewed.

Bell, C. E.↗

Use of Remote Sensing/Geographical Information Systems (RS/GIS) to Identify the Distributional Limits of Soil-Transmitted Helminths (STHs) and Their Association to Prevalence of Intestinal Infection in School-Age Children in Four Rural Communities in Boaco, Nicaragua

STHs can infect all members of a population but school-age children living in poverty are at greater risk. Infection can be controlled with drug treatment, health education and sanitation. Helminth control programs often lack resources and reliable information to identify areas of highest risk to guide interventions and to monitor progress. Objectives: To use RS/GIS to identify the environmental variables that correlate with the ecology of STHs and with the prevalence of STH infections. Methods: Geo-referenced in situ prevalence data will be overlaid over an ecological map derived from the RS environmental data using ESRI s ArcGIS 9.3. Prevalence data and RS environmental data matching at the same geographical location will be analyzed for correlation and those RS environmental variables that better correlate with prevalence data will be included in a multivariate regression model. Temperature, vegetation, and distance to bodies of water will be inferred using data from the Moderate-Resolution Imaging Spectroradiometer (MODIS) onboard the Terra and Aqua satellites, and Thematic Mapper (TM) and Enhance Thematic Mapper Plus (ETM+) satellite sensors onboard Landsat 5 and Landsat 7 respectively. Elevation will be estimated with data from The Shuttle Radar Topography Mission (SRTM). Prevalence and intensity of infections will be determined by parasitological survey (Kato Katz) of children enrolled in rural schools in Boaco, Nicaragua, in the communities of El Roblar, Cumaica Norte, Malacatoya 1, and Malacatoya 2). Expected Results: Associations between RS environmental data and prevalence in situ data will be determined and their applications to public health will be discussed. Discussion/Conclusions: The use of RS/GIS data to predict the prevalence of STH infections could be useful for helminth control programs, providing improved geographical guidance of interventions while increasing cost-effectiveness. Learning Objectives: (1) To identify the RS environmental variables that can help predict the prevalence of STH infections. (2) To understand potential applications of RS/GIS to national helminth control programs. (3) To asses the applicability of RS/GIS to control STH infections.

Moreno, Max J.↗

Helicopter Flight Test of 3-D Imaging Flash LIDAR Technology for Safe, Autonomous, and Precise Planetary Landing

Two flash lidars, integrated from a number of cutting-edge components from industry and NASA, are lab characterized and flight tested for determination of maximum operational range under the Autonomous Landing and Hazard Avoidance Technology (ALHAT) project (in its fourth development and field test cycle) which is seeking to develop a guidance, navigation, and control (GN&C) and sensing system based on lidar technology capable of enabling safe, precise crewed or robotic landings in challenging terrain on planetary bodies under any ambient lighting conditions. The flash lidars incorporate pioneering 3-D imaging cameras based on Indium-Gallium-Arsenide Avalanche Photo Diode (InGaAs APD) and novel micro-electronic technology for a 128 x 128 pixel array operating at 30 Hz, high pulse-energy 1.06 micrometer Nd:YAG lasers, and high performance transmitter and receiver fixed and zoom optics. The two flash lidars are characterized on the NASA-Langley Research Center (LaRC) Sensor Test Range, integrated with other portions of the ALHAT GN&C system from partner organizations into an instrument pod at NASA-JPL, integrated onto an Erickson Aircrane Helicopter at NASA-Dryden, and flight tested at the Edwards AFB Rogers dry lakebed over a field of human-made geometric hazards during the summer of 2010. Results show that the maximum operational range goal of 1 km is met and exceeded up to a value of 1.2 km. In addition, calibrated 3-D images of several hazards are acquired in real-time for later reconstruction into Digital Elevation Maps (DEM's).

Roback, Vincent↗

Guidance and Control Design for High-Speed Rollout and Turnoff (ROTO)

A ROTO architecture, braking and steering control law and display designs for a research high speed Rollout and Turnoff (ROTO) system applicable to transport class aircraft are described herein. Minimum surface friction and FMS database requirements are also documented. The control law designs were developed with the aid of a non-real time simulation program incorporating airframe and gear dynamics as well as steering and braking guidance algorithms. An attainable objective of this ROTO system, as seen from the results of this study, is to assure that the studied aircraft can land with runway occupancy times less then 53 seconds. Runway occupancy time is measured from the time the aircraft crosses the runway threshold until its wing tip clears the near side of the runway. Turnoff ground speeds of 70 knots onto 30 degree exits are allowed with dry and wet surface conditions. Simulation time history and statistical data are documented herein. Parameters which were treated as variables in the simulation study include aircraft touchdown weight/speed/location, aircraft CG, runway friction, sensor noise and winds. After further design and development of the ROTO control system beyond the system developed earlier, aft CG MD-11 aircraft no longer require auto-asymmetric braking (steering) and fly-by-wire nose gear steering. However, the auto ROTO nose gear hysteresis must be less than 2 degrees. The 2 sigma dispersion certified for MD-11 CATIIIB is acceptable. Using this longitudinal dispersion, three ROTO exits are recommended at 3300, 4950 and 6750 feet past the runway threshold. The 3300 foot exit is required for MD-81 class aircraft. Designs documented in this report are valid for the assumptions/models used in this simulation. It is believed that the results will apply to the general class of transport aircraft; however further effort is required to validate this assumption for the general case.

Goldthorpe, S. H.↗

Latency in Visionic Systems: Test Methods and Requirements

A visionics device creates a pictorial representation of the external scene for the pilot. The ultimate objective of these systems may be to electronically generate a form of Visual Meteorological Conditions (VMC) to eliminate weather or time-of-day as an operational constraint and provide enhancement over actual visual conditions where eye-limiting resolution may be a limiting factor. Empirical evidence has shown that the total system delays or latencies including the imaging sensors and display systems, can critically degrade their utility, usability, and acceptability. Definitions and measurement techniques are offered herein as common test and evaluation methods for latency testing in visionics device applications. Based upon available data, very different latency requirements are indicated based upon the piloting task, the role in which the visionics device is used in this task, and the characteristics of the visionics cockpit display device including its resolution, field-of-regard, and field-of-view. The least stringent latency requirements will involve Head-Up Display (HUD) applications, where the visionics imagery provides situational information as a supplement to symbology guidance and command information. Conversely, the visionics system latency requirement for a large field-of-view Head-Worn Display application, providing a Virtual-VMC capability from which the pilot will derive visual guidance, will be the most stringent, having a value as low as 20 msec.

Bailey, Randall E.↗

Assessment of NASA Airborne Laser Altimetry Data Using Ground-Based GPS Data near Summit Station, Greenland

A series of NASA airborne lidars have been used in support of satellite laser altimetry missions. These airbornelaser altimeters have been deployed for satellite instrument development, for spaceborne data validation, and to bridge the data gap between satellite missions. We used data from ground-based Global Positioning System (GPS) surveys of an 11 km long track near Summit Station, Greenland, to assess the surface elevation bias and measurement precision of three airborne laser altimeters including the Airborne Topographic Mapper (ATM), the Land, Vegetation, and Ice Sensor (LVIS), and the Multiple Altimeter Beam Experimental Lidar (MABEL). Ground-based GPS data from the monthly ground-based traverses, which commenced in 2006, allowed for the assessment of nine airborne lidar surveys associated with ATM and LVIS between 2007 and 2016. Surface elevation biases for these altimeters over the flat, ice-sheet interior are less than 0.12 m, while assessments of measurement precision are 0.09 m or better. Ground-based GPS positions determined both with and without differential post-processing techniques provided internally consistent solutions. Results from the analyses of ground-based and airborne data provide validation strategy guidance for the Ice, Cloud, and land Elevation Satellite 2 (ICESat-2) elevation and elevation-change data products.

Summit Station↗

NASA Electronic Parts and Packaging (NEPP) Program - Update

This slide presentation reviews the goals and mission of the NASA Electronic Parts and Packaging (NEPP) Program. The NEPP mission is to provide guidance to NASA for the selection and application of microelectronics technologies, to improve understanding of the risks related to the use of these technologies in the space environment and to ensure that appropriate research is performed to meet NASA mission assurance needs. The program has been supporting NASA for over 20 years. The focus is on the reliability aspects of electronic devices. In this work the program also supports the electronics industry. There are several areas that the program is involved in: Memories, systems on a chip (SOCs), data conversion devices, power MOSFETS, power converters, scaled CMOS, capacitors, linear devices, fiber optics, and other electronics such as sensors, cryogenic and SiGe that are used in space systems. Each of these area are reviewed with the work that is being done in reliability and effects of radiation on these technologies.

LaBel, Kenneth A.↗

Hazard Boresight Relative Navigation for Safe Lunar Landing

In the area of planetary landing, hazard detection and avoidance is the act of driving a vehicle to a safe landing area using onboard resources. A hazard detection sensor is used to scan the terrain and these measurements are evaluated to determine where the safe landing sites are located. The selected site is generally not the same as the nominal target, so the vehicle must divert to the new site. This activity involves the interaction between several components, including a suite of onboard GNC algorithms that work together to efficiently choose and divert to a new site. This paper presents the Hazard Boresight Relative Navigation concept, which is a method that provides a common interface between the hazard scan, safe-site selection algorithm, size of the target-relative landing ellipse, divert offset distance and guidance targeting algorithm. After the safe-site is selected from the hazard scan, the original inertial target is replaced with a vehicle-relative target, which is initialized by a measurement from the hazard scan. The new target-relative position state is estimated over time in the navigation filter, and is fed to the guidance algorithm to perform the divert maneuver. In addition to detailing the Hazard Boresight Relative Navigation concept, this paper also presents some general landing terms that can be used in the greater discussion, as well as analysis on how to estimate and predict the vehicle footprint dispersion ellipse during flight, which is used in the safe-site selection algorithm.

Stephen R. Steffes↗

Hazard Boresight Relative Navigation for Safe Lunar Landing

In the area of planetary landing, hazard detection and avoidance is the act of driving a vehicle to a safe landing area using onboard resources. A hazard detection sensor is used to scan the terrain and these measurements are evaluated to determine where the safe landing sites are located. The selected site is generally not the same as the nominal target, so the vehicle must divert to the new site. This activity involves the interaction between several components, including a suite of onboard GNC algorithms that work together to efficiently choose and divert to a new site. This paper presents the Hazard Boresight Relative Navigation concept, which is a method that provides a common interface between the hazard scan, safe-site selection algorithm, size of the target-relative landing ellipse, divert offset distance and guidance targeting algorithm. After the safe-site is selected from the hazard scan, the original inertial target is replaced with a vehicle-relative target, which is initialized by a measurement from the hazard scan. The new target-relative position state is estimated over time in the navigation filter, and is fed to the guidance algorithm to perform the divert maneuver. In addition to detailing the Hazard Boresight Relative Navigation concept, this paper also presents some general landing terms that can be used in the greater discussion, as well as analysis on how to estimate and predict the vehicle footprint dispersion ellipse during flight, which is used in the safe-site selection algorithm.

Stephen Steffes↗

Autoguidance video sensor for docking

The Automated Rendezvous and Docking system (ARAD) is composed of two parts. The first part is the sensor which consists of a video camera ringed with two wavelengths of laser diode. The second part is a standard Remote Manipulator System (RMS) target used on the Orbiter that has been modified with three circular pieces of retro-reflective tape covered by optical filters which correspond to one of the wavelengths of laser diode. The sensor is on the chase vehicle and the target is on the target vehicle. The ARAD system works by pulsing one wavelength laser diodes and taking a picture. Then the second wavelength laser diodes are pulsed and a second picture is taken. One picture is subtracted from the other and the resultant picture is thresholded. All adjacent pixels above threshold are blobbed together (X and Y centroids calculated). All blob centroids are checked to recognize the target out of noise. Then the three target spots are windowed and tracked. The three target spot centroids are used to evaluate the roll, yaw, pitch, range, azimuth, and elevation. From that a guidance routine can guide the chase vehicle to dock with the target vehicle with the correct orientation.

Book, Michael L.↗

NASA and Blue Origin Collaborative Assessment of Precision Landing Algorithms and Computing

NASA’s Safe and Precise Landing Integrated Capabilities Evolution (SPLICE) project is developing sensor, algorithm, and compute technologies for precision landing and hazard avoidance. These technologies are being tested as an integrated Precision Landing and Hazard Avoidance (PL&HA) system on Blue Origin’s New Shephard suborbital vehicle. A key goal for the computing element of this technology development is to characterize the performance of the SPLICE software workloads on the project’s Descent and Landing Computer (DLC). The DLC is a multi-core processor designed as a surrogate for NASA’s High-Performance Space Computer (HPSC). Measurements of the SPLICE workload performance on the DLC provides NASA insight on how PL&HA capabilities will perform on the HPSC, and guidance on how the SPLICE algorithms can be implemented to best utilize the DLC platform. This insight can also be used to derive requirements to guide trade studies on candidate computing architectures, for use on platforms like Blue Moon. NASA and Blue Origin are collaborating under an agreement to pursue this mutual benefit. Performance metrics collected are based on measurement of common compute resources such as percentage used of memory bandwidth, I/O utilization, interrupt latency, and kernel vs. user space code residency. Where possible existing performance counters and metrics that are part of the operating system kernel are used. As the design has a significant FPGA component, performance counters are identified and instantiated in the fabric to measure DMA performance and interface metrics. Collection of metrics is performed on the DLC with a representative workload that simulates a full landing cycle of the Blue Origin New Shepard vehicle. Consideration is given to the other compute implementations and whether they can run SPLICE algorithms at the same rate and with the same latency as the DLC. One option being considered is the use of a RISC-V soft core instantiated in a radiation resilient FPGA fabric such as the Xilinx KU60. Select algorithms from the SPLICE code will be run for comparison with the DLC. This paper describes how the DLC is instrumented to collect performance measurements of the SPLICE workloads, preliminary results from these measurements, and their implications on SPLICE algorithm implementation. The results of experimentation to derive candidate requirements for architecture trades on a PL&HA computing system are also presented.

computer performance↗

Optimizing infrasound observations for sample return capsule re-entry: Insights from OSIRIS-REx and Hayabusa2

The atmospheric entry of meteoroids presents a rare and unpredictable phenomenon, posing challenges for systematic observation and detailed characterization. Such events are nonetheless critical for advancing understanding of acoustic wave propagation, atmospheric structure, and entry dynamics. In contrast, sample return capsules (SRCs) from space missions follow well constrained re-entry trajectories, enabling planned observations of shock wave generation and propagation under controlled conditions. This study compares two SRC atmospheric entries, Hayabusa2 in 2020 and OSIRIS-REx in 2023, to assess how different infrasound array configurations influence shock wave detection and trajectory validation. Hayabusa2’s re-entry was monitored using a distributed network of 28 portable infrasound sensors across seven arrays in Woomera, Australia, permitting three-dimensional reconstruction of the trajectory and analysis of wave characteristics. For OSIRIS-REx, a compact four-sensor array deployed near Eureka Airport provided trajectory confirmation through arrival-time differences and back-azimuth estimates. Spectral and waveform analyses revealed differences in signal properties associated with variations in entry angle and velocity. The results illustrate both the strengths and the limitations of the deployed array configurations. The dense and distributed arrays during Hayabusa2’s re-entry enabled detailed trajectory reconstruction, whereas the compact array at Eureka primarily provided confirmation of signal coherence and back-azimuth consistency. These case studies highlight that even relatively small arrays, if located close to the predicted ground track, can still capture useful information on arrival direction and timing. Such insights provide practical guidance for planning future observational campaigns of SRC returns and other controlled atmospheric entries, and may also inform approaches to opportunistic observations of meteoroid events and other atmospheric acoustic phenomena.

celestial mechanics: orbit determination↗

Depth-dependent Vertical-to-Horizontal (V/H) Ratios of Free-Field Ground Motion Response Spectra for Deeply Embedded Nuclear Structures

This report documents the results of a study to determine the depth-dependent V/H ratios of ground motion response spectra in the free field. The V/H ratios reported herein were developed from a worldwide database of surface and downhole acceleration recordings obtained from 45 vertical array stations. This database was specifically compiled for this project, and includes information from a diversity of active tectonic regions (California, Alaska, Taiwan, Japan), site conditions (rock to soft soil), ground motion intensity levels (PGAs between 0.01 g and 0.50 g), magnitudes (between ML 2.78 and JMA 8.1), epicentral distances (between 3.2 km and 812 km), and source depths (between 1.2 km and 112 km), as well as sensors at surface and at a wide range of depths relevant to the project. To study the significance of the depth effect, V/H ratios from all the records were sorted into a number of depth bins relevant to the project, and statistics (average, standard deviation, coefficient of variation, 16th, 50th, and 84th percentiles) of the V/H ratios within each bin were computed. Similar analyses were repeated, controlling for different site conditions, ground motion intensity levels, array locations, and source depths, to study their relative effect on the V/H ratios. Our findings confirm the importance of the depth effect on the V/H ratios. The research findings in this report can be used to provide guidance on the significance of the depth effect, and the extent to which this effect should be considered in the seismic design of deeply embedded SMR structures and NPP structures in general.

42 ENGINEERING↗

Weather Guidance for UAS Urban Medical Transport Missions

Unmanned aircraft will revolutionize healthcare services by providing efficient and expeditious delivery of life-saving transplant organs and supplies to hospitals in urban environments, where road traffic and congestion can slow delivery times and endanger lives. Bell has developed the Autonomous Pod Transport (APT) vehicle to serve this market, with entry into service in mid-2020s. Adverse weather conditions can introduce risks and inefficiencies in urban environments leading to flight delays and cancellations. In 2018, National Aeronautics and Space Administration (NASA) and Bell entered into a cooperative agreement, under the Systems Integration and Operationalization (SIO) program to tackle key challenges to enable future commercial unmanned aircraft operations. The Center for Collaborative Adaptive Sensing of the Atmosphere (CASA) at the University of Massachusetts, Amherst, joined this team to demonstrate weather avoidance technologies for remotely piloted and autonomous vehicles. CASA has developed the ‘City Warn’ hazard alerting platform to gather weather information from various weather sensors and models, and based on user (or mission) preferences for alerting and on user (or unmanned aircraft) locations, the platform shares timely weather intelligence with users and the systems used by them for remote operations. This presentation discusses the weather avoidance solution developed during this project, leading up to the demonstration of the end-to-end system in Fall 2020. The presentation will cover the following topics: 1) goals related to weather avoidance 2) the design requirements process, including the results of pilot interviews, 3) weather observation and avoidance needs 4) selection of regional and national weather data sets 5) design of the weather graphical interface and 6) considerations for real-time weather alerting. The end-to-end system that was developed will be discussed, along with the results from the demonstration flight. The presentation will conclude with insights from the project team on lessons learned and best practices on weather avoidance technologies for the industry going ahead.

weather avoidance↗

Weather Guidance for UAS Urban Medical Transport Missions

Unmanned aircraft will revolutionize healthcare services by providing efficient and expeditious delivery of life-saving transplant organs and supplies to hospitals in urban environments, where road traffic and congestion can slow delivery times and endanger lives. Bell has developed the Autonomous Pod Transport (APT) vehicle to serve this market, with entry into service in mid-2020s. Adverse weather conditions can introduce risks and inefficiencies in urban environments leading to flight delays and cancellations. In 2018, National Aeronautics and Space Administration (NASA) and Bell entered into a cooperative agreement, under the Systems Integration and Operationalization (SIO) program to tackle key challenges to enable future commercial unmanned aircraft operations. The Center for Collaborative Adaptive Sensing of the Atmosphere (CASA) at the University of Massachusetts, Amherst, joined this team to demonstrate weather avoidance technologies for remotely piloted and autonomous vehicles. CASA has developed the ‘City Warn’ hazard alerting platform to gather weather information from various weather sensors and models, and based on user (or mission) preferences for alerting and on user (or unmanned aircraft) locations, the platform shares timely weather intelligence with users and the systems used by them for remote operations. This presentation discusses the weather avoidance solution developed during this project, leading up to the demonstration of the end-to-end system in Fall 2020. The presentation will cover the following topics: 1) goals related to weather avoidance 2) the design requirements process, including the results of pilot interviews, 3) weather observation and avoidance needs 4) selection of regional and national weather data sets 5) design of the weather graphical interface and 6) considerations for real-time weather alerting. The end-to-end system that was developed will be discussed, along with the results from the demonstration flight. The presentation will conclude with insights from the project team on lessons learned and best practices on weather avoidance technologies for the industry going ahead.

weather avoidance↗

Value of Information and Data Management Platform Promoting Modern Data Analysis Utilization. STTR Phase I, Final Technical Report

The immense growth in weather and river sensor data availability along with increases in computational power and algorithmic sophistication have enabled the widespread application of physical, machine learning, and artificial intelligence algorithms to river forecasting. The forecasts produced by widely varying model approaches are inherently limited in different ways, such as by the number and quality of training observations, producing biased predictions that achieve optimal skill only over specific ranges of weather and river conditions. Thus, despite the growing availability and new sources of forecasts, hydropower owners cannot fully leverage the information because they lack an effective mechanism to determine the “best” forecast for given conditions or objectives. Tools are needed to consolidate forecast information, demonstrate skill, and extract optimal forecast guidance from the range of possibilities. Such tools will increase uptake and beneficial use of the growing wealth of forecast information, and lead to improved operating decisions, optimal power generation, and enhanced system value. This research proposes to improve the value of forecasts by developing a broadly accessible verification framework and applying machine learning techniques to identify the ‘best’ forecast from an ensemble of sources given the current weather, river, and operating conditions.

13 HYDRO ENERGY↗

Software for Engineering Simulations of a Spacecraft

Spacecraft Engineering Simulation II (SES II) is a C-language computer program for simulating diverse aspects of operation of a spacecraft characterized by either three or six degrees of freedom. A functional model in SES can include a trajectory flight plan; a submodel of a flight computer running navigational and flight-control software; and submodels of the environment, the dynamics of the spacecraft, and sensor inputs and outputs. SES II features a modular, object-oriented programming style. SES II supports event-based simulations, which, in turn, create an easily adaptable simulation environment in which many different types of trajectories can be simulated by use of the same software. The simulation output consists largely of flight data. SES II can be used to perform optimization and Monte Carlo dispersion simulations. It can also be used to perform simulations for multiple spacecraft. In addition to its generic simulation capabilities, SES offers special capabilities for space-shuttle simulations: for this purpose, it incorporates submodels of the space-shuttle dynamics and a C-language version of the guidance, navigation, and control components of the space-shuttle flight software.

Shireman, Kirk↗