Search NASA⌕ Search

SEARCH · Search NASA

Results for “IMPACT SHOCK”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42

Shock-tube pyrolysis of acetylene - Sensitivity analysis of the reaction mechanism for soot formation

The impact of thermodynamic parameters on the sensitivity of model predictions of soot formation by shock-tube pyrolysis of acetylene were assessed analytically. The pyrolysis process was treated as having three components: initiation, the initial pyrolysis stages; cyclization, formation of larger molecules and radicals and small aromatic molecules; and polymerization, further growth of aromatic rings. Rate equations are reviewed for each component. Thermodynamic effects were assessed by varying the C2H-H and C2H3-H bond energies and the Ct-(Ct) group additivity value. Any change in the C2H-H bond energy had a significant impact on the temperature and the maximum amount of the soot yield. The findings underscore the necessity of using accurate thermodynamic data for modeling high-temperature chemical kinetics.

Frenklach, M.↗

Porosity effect on supercritical airfoil drag reduction by shock wave/boundary layer control

An investigation of the passive shock wave/boundary layer control for reducing the drag of 14 percent-thick supercritical airfoil was conducted in the 3 in. x 15.4 in. RPI Transonic Wind Tunnel at transonic Mach numbers. Various porous surfaces with a cavity beneath it was positioned on the area of the airfoil, mounted on the test section bottom wall, where the shock wave occurs. The static pressure distributions over the airfoil, the wake impact pressure survey for determining the profile drag and the Schlieren photographs for porous surfaces are presented and compared with the results for solid surface airfoil. With a uniform porosity surface the normal shock wave for solid surface was changed to a lambda shock wave, and the wake impact pressure data indicated an appreciable drag reduction at transonic Mach numbers. For a free stream Mach number of 0.81 the profile drag coefficient for the airfoil top surface with uniform porosity was 46 percent lower than for the solid surface airfoil.

Nagamatsu, H. T.↗

Impact flows and crater scaling on the moon

The axisymmetric distribution of stress, internal energy, and particle velocity resulting from the impact of an iron meteoroid with a gabbroic anorthosite lunar crust has been calculated for the regime in which shock-induced melting and vaporization take place. Comparison of impact flow fields, with phase changes in silicates taken into account, with earlier results demonstrate that in the phase-change case where the 15-km/s projectile has penetrated some two projectile radii into the moon, the peak stress in the flow is about 0.66 Mbar at a depth of 66 km, and the stress has decayed to about 66 kbar at a depth of 47 km. Rapid attenuation occurs because of the high rarefaction velocity of the high-pressure phases associated with a 35% (zero-pressure) density increase. This feature of the phase-change flow tends to concentrate strongly the maximum shock pressures along the meteoroid trajectory (axis) and makes the conical zone along which high internal energy deposition occurs both shallow and narrow. Examination of the gravitational energies required to excavate larger craters on the moon indicates the importance of gravity forces acting during the excavation of craters having radii in the range greater than about 2 to 140 km.

Okeefe, J. D.↗

Investigation of ion kinetic effects in direct-drive exploding-pusher implosions at the NIF

Measurements of yield, ion temperature, areal density (rhoR), shell convergence, and bang time have been obtained in shock-driven, D2 and D3He gas-filled “exploding-pusher” inertial confinement fusion (ICF) implosions at the National Ignition Facility (NIF) to assess the impact of ion kinetic effects. These measurements probed the shock convergence phase of ICF implosions, a critical stage in hot-spot ignition experiments. The data complement previous studies of kinetic effects in shock-driven implosions. Ion temperature and fuel rhoR inferred from fusion-product spectroscopy are used to estimate the ion-ion mean free path in the gas. A trend of decreasing yields relative to the predictions of 2D draco hydrodynamics simulations with increasing Knudsen number (the ratio of ion-ion mean free path to minimum shell radius) suggests that ion kinetic effects are increasingly impacting the hot fuel region, in general agreement with previous results. The long mean free path conditions giving rise to ion kinetic effects in the gas are often prevalent during the shock phase of both exploding pushers and ablatively-driven implosions, including ignition-relevant implosions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Inertial collapse of a gas bubble in a shear flow near a rigid wall

Despite the extensive research on bubble collapse near rigid walls, the bubble collapse dynamics in the presence of shear flow near a rigid wall is poorly understood. We conduct direct simulations of the Navier–Stokes equations to explore the bubble dynamics and pressures during bubble collapse near a rigid, flat wall under linear shear flow conditions. We examine the dependence of the bubble collapse morphology and wall pressures on the initial bubble location and shear rate. We find that shear distorts the bubble, generating two re-entrant jets – one developing from the side opposite to the mean flow and the other from the far end toward the wall. Upon impact of the jet on the opposite side of the bubble, water-hammer shocks are produced, which propagate outward and interact with the convoluted bubble shape. The shock stretches the bubble towards the wall, resulting in a closer impact location for the jet originating from the far end compared with the case with no shear flow. The water-hammer pressure location can be approximated as the theoretical distance travelled by a particle initialised at the bubble centre with the corresponding constant shear flow velocity. The maximum wall pressures can thus be predicted by considering the distance between the far jet impingement location and the wall along the wall-normal direction. As the shear rate is increased, the maximum wall pressure increases, although only marginally. We determine the critical initial stand-off distance from the wall at which the bubble morphology is shear dominated, i.e. characterised by converging re-entrant jets.

Bhola, Sahil (ORCID:0000000236766302)↗

Shock physics at the nanoscale [Invited]

Shock waves can achieve extreme states of pressure and temperature, of particular interest because those conditions can result in non-equilibrium material dynamics that evolve on ultrafast timescales. Examples of such phenomena include shock-induced chemistry and phase transitions. Traditional plate impact methods lack the necessary time and space resolution needed to observe the onset of ultrafast nanoscale phenomena. Sub-picosecond time scale and nanometer spatial scale shock compression and diagnostics methods have been developed to surmount such difficulties. In conclusion, this paper reviews a number of nanoscale shock wave generation methods, as well as the diagnostics that are applicable at these restrictive time and spatial scales.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Experimental shock lithification of water-bearing rock powders

The geology and morphology of the terrestrial planets and their moons have been profoundly affected by impact cratering. Some of these bodies contain substantial quantities of water or ice in their regoliths. It is pointed out that the effects of impacts into water-bearing target rocks are not well understood, and may be significantly different from those produced by identical impacts on a desiccated surface. The present investigation has the objective to determine the effects of water on targets of powdered rock and to seek evidence of impact-induced hydration or clay formation. Samples of andesitic basalt were crushed and sieved, and experiments were conducted on the material smaller than 150 micrometers. These experiments show that the water content of a powdered rock target can strongly affect its physical condition following an impact. A relatively small component (5-15 wt %) of water or ice in planetary surface material could inhibit or prevent lithification throughout much of the shocked volume at an impact site.

Allen, C. C.↗

Proteome of Salmonella enterica serotype Tyhimurium Grown in Low Mg2+/pH Medium

To determine the impact of a low Mg2+/pH defined growth medium (MgM) on the proteome of Salmonella enterica serotype Typhimurium, we cultured S. Typhimurium cells in the medium under two different conditions termed MgM Shock and MgM Dilution and then comparatively analyzed the bacterial cells harvested from these conditions by a global proteomic approach. Proteomic results showed that MgM Shock and MgM Dilution differentially affected the S. Typhimurium proteome. MgM Shock induced a group of proteins whose induction usually occurred at low O2 level, while MgM Dilution induced those related to the type III secretion system (T3SS) of Salmonella Pathogenicity Island 2 (SPI2) and those involved in thiamine or biotin biosynthesis. The metabolic state of the S. Typhimurium cells grown under MgM Shock condition also differed significantly from that under MgM Dilution condition. Western blot analysis not only confirmed the proteomic results, but also showed that the abundances of SPI2-T3SS proteins SsaQ and SseE and biotin biosynthesis proteins BioB and BioD increased after S. Typhimurium infection of RAW 264.7 macrophages. Deletion of the gene encoding BioB reduced the bacterial ability to replicate inside the macrophages, suggesting a biotin-limited environment encountered by S. Typhimurium within RAW 264.7 macrophages.

59 BASIC BIOLOGICAL SCIENCES↗

Shock melting and vaporization of lunar rocks and minerals.

The entropy associated with the thermodynamic states produced by hypervelocity meteoroid impacts at various velocities are calculated for a series of lunar rocks and minerals and compared with the entropy values required for melting and vaporization. Taking into account shock-induced phase changes in the silicates, we calculate that iron meteorites impacting at speeds varying from 4 to 6 km/sec will produce shock melting in quartz, plagioclase, olivine, and pyroxene. Although calculated with less certainty, impact speeds required for incipient vaporization vary from 7 to 11 km/sec for the range of minerals going from quartz to periclase for aluminum (silicate-like) projectiles. The impact velocities, which are required to induce melting in a soil, are calculated to be in the range of 3 to 4 km/sec, provided thermal equilibrium is achieved in the shock state.

Ahrens, T. J.↗

Extrapolation of space weathering processes to other small solar system bodies

A diverse range of processes were invoked as the dominant factor or as important contributory factors in the modification of the optical surface and regolith of the moon. These include impact vitrification by large and small projectiles, solar wind implantation and the reduction of oxidized iron during energetic events, sputtering and crystal lattice damage by energetic cosmic rays, shock metamorphism of minerals, mixing of diverse lithologies by impacts, and contamination by external materials. These processes are also potentially important on the rocky surfaces of other small solar system bodies. For icy bodies, several additional processes are also possible, including formation of complex organic compounds from methane and ammonia-bearing ices by ultraviolet irradiation and the condensation of vapor species to form frost layers in the polar or cooler regions of objects at appropriate heliocentric distances. The lunar case, even when completely understood, will not extend in a simple linear fashion to other small rocky objects, nor will the optical surfaces of those objects all be affected to the same degree by each process. The major factors that will control the relative efficacy of a possible mechanism include the efficiency of ejecta retention and the degree to which the regolith materials experience multiple events (primarily a function of body size, escape velocity, and impactor velocities); the mean duration of typical regolith particle exposure at the optical surface and within reach of the micrometeorite, cosmic ray, solar wind, or UV fluxes (a function of the rate and scale of regolith mixing, production, and removal processes); the incident flux of solar (low energy) cosmic rays, solar wind, or UV radiation (inverse square of heliocentric distance) or of galactic (high energy) cosmic rays (slowly increasing flux with heliocentric distance); and the compositional and mineralogical nature of the surface being affected. In general, those processes that depend upon either the retention of impact ejecta or on the presence of multigenerational regoliths should be substantially less effective on smaller bodies with lower escape velocities. However, there are important exceptions to this generalization. For example, a process that involves the hypervelocity impact of small particles into a fine-grained regolith may be able to effectively retain highly shocked or melted material due to the nature of shock wave propagation in such a heterogeneous material.

Gaffey, M. J.↗

Grain orientation effects on dynamic strength of FCC multicrystals at low shock pressures: a hydrodynamic instability study

Variability in local dynamic plasticity due to material anisotropy in polycrystalline metals is likely to be important on damage nucleation and growth at low pressures. Hydrodynamic instabilities could be used to study these plasticity effects by correlating measured changes in perturbation amplitudes at free surfaces to local plastic behaviour and grain orientation, but amplitude changes are typically too small to be measured reliably at low pressures using conventional diagnostics. Correlations between strength at low shock pressures and grain orientation were studied in copper (grain size ≈ 800 μm) using the Richtmyer–Meshkov instability with a square-wave surface perturbation (wavelength = 150 μm, amplitude = 5 μm), shocked at 2.7 GPa using symmetric plate impacts. A Plexiglas window was pressed against the peaks of the perturbation, keeping valleys as free surfaces. This produced perturbation amplitude changes much larger than those predicted without the window. Amplitude reductions from 64 to 88% were measured in recovered samples and grains oriented close to $\langle$0 0 1$\rangle$ parallel to the shock had the largest final amplitude, whereas grains with shocks directions close to $\langle$1 0 1$\rangle$ had the lowest. Finite element simulations were performed with elastic-perfectly plastic models to estimate yield strengths leading lead to those final amplitudes. Anisotropic elasticity and these yield strengths were used to calculate the resolved shear stresses at yielding for the two orientations. In conclusion, results are compared with reports on orientation dependence of dynamic yielding in Cu single crystals and the higher values obtained suggest that strength estimations via hydrodynamic instabilities are sensitive to strain hardening and strain rate effects.

36 MATERIALS SCIENCE↗

Discovery of coesite and shocked quartz associated with the upper Eocene cpx spherule layer

At least two major impact ejecta layers have been discovered in upper Eocene strata. The upper layer is the North American microtektite layer. lt consists tektite fragments, microtektites, and shocked mineral grains (e.g., quartz and feldspar with multiple sets of PDFs, coesite and reidite (a high-pressure polymorph of zircon)). The slightly older layer contains clinopyroxene-bearing (cpx) spherules and microtektites associated with an Ir anomaly. The North American tektite layer may be derived from the Chesapeake Bay impact structure, and the cpx spherule layer may from the Popigai impact crater. A cpx spherule layer associated with a positive Ir anomaly was recently found at ODP Site 709, western Indian Ocean. A large sample (Hole 709C, core 31, section 4, 145-150 cm), originally used for a study of interstitial water by shipboard scientists, was acquired for the purpose of recovering a large number of spherules for various petrographic and geochemical studies. A split of the sample (50.35 g) was disaggregated and wet-sieved. More than 17,000 cpx spherules and several hundred microtektites (larger than 125 microns) were recovered from the sample. Rare white opaque grains were observed in the 125-250 micron size fraction after removal of the carbonate component using dilute HCI. Seven of the white opaque grains were X-rayed using a Gandolfi camera and six were found to be coesite (probably mixed with lechatelierite). Eighty translucent colorless grains from the 63-125 micron size fraction were studied with a petrographic microscope. Four of the grains exhibit one to two sets of planar deformation features (PDFs). The only other possible known occurrence of shocked minerals associated with the cpx spherule layer is at Massignano, Italy, where pancake-shaped clay spherules (thought to be diagenetically altered cpx spherules are associated with a positive Ir anomaly and Ni- rich spinel crystals. Shocked quartz grains with multiple sets of PDFs also occur at this site. Until now, unmelted impact ejecta have not been found associated with the cpx spherules at any of the other 20 sites around the world and this is the first time that coesite has been found associated with the cpx spherule layer. The discovery of coesite and shocked quartz associated with the cpx spherules at Site 709 in Indian Ocean is further evidence for the impact origin of the cpx spherule layer. We hope that future discovery of other unmelted minerals from this sample may provide materials to establish constraints on the provenance of this late Eocene ejecta.

Liu, S.↗

High-speed x-ray phase contrast imaging and digital image correlation analysis of microscale shock response of an additively manufactured energetic material simulant

The performance of energetic materials subjected to dynamic loading significantly depends on their micro- and meso-scale structural morphology. The geometric versatility offered by additive manufacturing opens new pathways to tailor the performance of these materials. Additively manufactured energetic materials (AMEMs) have a wide range of structural characteristics with a hierarchy of length scales and process-inherent heterogeneities, which are hitherto difficult to precisely control. It is important to understand how these features affect AMEMs’ response under dynamic/shock loading. Therefore, temporally and spatially resolved measurements of both macroscopic behavior and micro- and meso-level processes influencing macroscopic behavior are required. In this paper, we analyze the shock compression response of an AMEM simulant loaded under several impact conditions and orientations. Furthermore, x-ray phase contrast imaging (PCI) is used to track features across the observed shock front and determine the linear shock velocity vs particle velocity equation of state, as well as to quantify the interior deformation fields via digital image correlation (DIC) analyses. Photon Doppler velocimetry is simultaneously used to measure the particle velocities of the specimens, which are consistent with those obtained from x-ray PCI. The DIC analyses provide an assessment of the average strain fields inside the material, showing that the average axial strain depends on the loading intensity and reaches as high as 0.23 for impact velocities up to 1.5 km/s. The overall results demonstrate the utility of x-ray PCI for probing “in-material” equation of state and interior strains associated with dynamic shock compression behavior of the AMEM simulant.

3D printing↗

Impact-induced devolatilization and hydrogen isotopic fractionation of serpentine: Implications for planetary accretion

Impact-induced devolatilization of porous serpentine was investigated using two independent experimental methods, the gas recovery and the solid recovery method, each yielding nearly identical results. For shock pressures near incipient devolatilization, the hydrogen isotopic composition of the evolved H2O is very close to that of the starting material. For shock pressures at which up to 12 percent impact-induced devolatilization occurs, the bulk evolved gas is significantly lower in deuterium than the starting material. There is also significant reduction of H2O to H2 in gases recovered at these higher shock pressures, probably caused by reaction of evolved H2O with the metal gas recovery fixture. Gaseous H2O-H2 isotopic fractionation suggests high temperature isotopic equilibrium between the gaseous species, indicating initiation of devolatilization at sites of greater than average energy deposition. Bulk gas-residual solid isotopic fractionations indicate nonequilibrium, kinetic control of gas-solid isotopic ratios. Impact-induced hydrogen isotopic fractionation of hydrous silicates during accretion can strongly affect the long-term planetary isotopic ratios of planetary bodies, leaving the interiors enriched in deuterium. Depending on the model used for extrapolation of the isotopic fractionation to devolatilization fractions greater than those investigated experimentally can result from this process.

Tyburczy, James A.↗

Oxygen Deficiency in Spaceflight & its Impact on Plants’ Adaptive Changes

The goal of this study was to investigate the effects of hypoxic conditions in spaceflight. The distribution of genes involved with hypoxia in Arabidopsis thaliana and Brassica rapa were analyzed with the results from past spaceflight experiments to evaluate genes for future studies. Transcriptomes data of two different spaceflight studies of Arabidopsis thaliana from the NASA GeneLab database, GLDS-7 and GLDS-17, were compared. DNA microarrays were utilized for transcription profiling to conduct these studies. For GLDS-7, the response in spaceflight was studied with approaches that collected gene expression data. Leaves, hypocotyls, and root tissues were compared to the whole plant. For GLDS-17, seedlings and undifferentiated cultured cells were placed in the Biological Research in Canisters (BRIC), specifically BRIC-16. The genes related to hypoxia in Arabidopsis thaliana from these two studies were compared to genes in Brassica rapa with the TOAST database to evaluate similarities. When transcriptomes were analyzed for GLDS-7 and 17, genes that were considered significant had p-values ≤ 0.05 and log fold change values ≤ -1 or ≥1. Sixteen genes fulfilled the criteria. The genes related to hypoxia were alcohol dehydrogenase, elongation factor, ethylene-responsive factor, GUS, heat-shock proteins, NAP, RAP2.12, and RD20. The genes most impacted by spaceflight were heat-shock proteins. These genes were compared with Brassica rapa through Arabidopsis Ensemble Orthology from the TOAST Database. Similarities were seen in alcohol dehydrogenase, elongation factor, ethylene-responsive factor, heat-shock proteins, NAP, and RAP2.12. Overall, transcription profiling indicates that plants’ survival in spaceflight is dependent on adaptive changes with gene expression. This study also indicates that there are similarities in gene expression between Arabidopsis thaliana and Brassica rapa with comparable gene expression. Future studies could include analyzing additional species to understand which genes could be modified to ensure better yield of space crops amid hypoxic conditions.

hypoxia↗

Shock Demagnetization of Pyrrhotite

Maps of the remanent magnetic field of Mars show demagnetized zones within and around giant impact basins. It is likely that vast regions of the Martian crust were demagnetized due to a shock-induced phase change or magnetic transition of magnetic minerals in the crust. This hypothesis is supported by the fact that around the Hellas and Argyre basins, the edges of the unmagnetized zones roughly correspond with peak shock pressure contour lines of a few GPa. Although pyrrhotite is not a major carrier of magnetization in the Earth s crust, it is a common phase in Martian meteorites and may be an important carrier in the Martian crust. Understanding the effects of shock waves on magnetic minerals is critical for determining the origin of the demagnetized zones in impact basins and possibly for identifying the major magnetic carrier phases. Here we present the results of the first controlled shock demagnetization measurements on pyrrhotite. Previous experiments: Shock demagnetization

Louzada, K. L.↗

Strongly Anisotropic Thermomechanical Response to Shock Wave Loading in Oriented Samples of the Triclinic Molecular Crystal 1,3,5-Triamino-2,4,6-trinitrobenzene

All-atom molecular dynamics (MD) simulations were used to study shock wave loading in oriented single crystals of the highly anisotropic triclinic molecular crystal 1,3,5-triamino-2,4,6-trinitrobenzene (TATB). The crystal structure consists of planar hydrogen-bonded sheets of individually planar TATB molecules that stack into graphitic-like layers. Shocks were studied for seven systematically prepared crystal orientations with limiting cases that correspond to shock propagation exactly perpendicular and exactly parallel to the graphitic-like layers. The simulations were performed for initially defect-free crystals using a reverse-ballistic configuration that generates explicit, supported shocks. Final longitudinal stress components are between ≈8.5 and ≈10.5 GPa for the 1.0 km s –1 impact speed studied. Orientation-dependent properties are reported including shock speeds, stresses, temperatures, compression ratios, and local material strain rates. Spatiotemporal maps of the temperature, stress tensor, material flow, and molecular orientations reveal complicated processes that arise for specific shock directions. Furthermore, the results indicate that TATB shock response is highly sensitive to crystal orientation, with significant qualitative differences for the time evolution of the stress tensor and temperature, elastic/inelastic compression response, defect formation and growth, critical von Mises stress, and strain rates during shock rise that span nearly an order of magnitude. A variety of inelastic deformation mechanisms are identified, ranging from crumpling of graphitic-like layers to dislocation-mediated plasticity to intense shear strain localization. To our knowledge, these are the first systematic MD simulations and analysis of explicit shock wave propagation along nontrivial crystal directions in a triclinic molecular crystal.

36 MATERIALS SCIENCE↗

Spall fracture in additive manufactured tantalum

In this work, we present a series of experiments on the response of additive manufactured (AM) tantalum to dynamic loading, specifically the spall strength. Rectangular plates of AM tantalum were produced, with subsequent characterization revealing a highly anisotropic microstructure. Samples were taken from these plates to investigate the effect of anisotropy on the spall strength: the resistance to high strain-rate tensile damage. A conventional, wrought tantalum sample, possessing an equiaxed microstructure, was also tested to serve as a control. Additionally, shock loading was performed via light gas-gun flyer-plate impact experiments, with laser velocimetry on the rear of the samples to record the shock wave profiles and soft-recovery techniques to allow post-mortem analysis. In general, the AM samples were found to have a higher Hugoniot elastic limit, the dynamic yield strength under shock loading, while having a reduced spall strength, when compared to the wrought tantalum samples.

36 MATERIALS SCIENCE↗