Search NASA⌕ Search

SEARCH · Search NASA

Results for “LINEAR PROGRAMMING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Dynamic characteristics of rotor blades with pendulum absorbers

The point transmission matrix for a vertical plane pendulum on a rotating blade undergoing combined flapwise bending, and chordwise bending and torsion is derived. The equilibrium equation of the pendulum is linearized for small oscillations about the steady state. A FORTRAN program was written for the case of a vertical plane pendulum attached to a uniform blade with flapwise bending degree of freedom for cantilever boundary conditions. The frequency has a singular value right at the uncoupled pendulum natural frequency and thus introduces two frequencies corresponding to the nearest natural frequency of the blade without pendulum. In both of these modes it was observed that the pendulum deflection is large. One frequency can be thought of as a coupled pendulum frequency and the other as a coupled bending and pendulum frequency.

Murthy, V. R.↗
NASA NTRS1979

NEWSUMT: A FORTRAN program for inequality constrained function minimization, users guide

A computer program written in FORTRAN subroutine form for the solution of linear and nonlinear constrained and unconstrained function minimization problems is presented. The algorithm is the sequence of unconstrained minimizations using the Newton's method for unconstrained function minimizations. The use of NEWSUMT and the definition of all parameters are described.

Miura, H.↗
NASA NTRS1981

Effects of static tensile load on the thermal expansion of Gr/PI composite material

The effect of static tensile load on the thermal expansion of Gr/PI composite material was measured for seven different laminate configurations. A computer program was developed which implements laminate theory in a piecewise linear fashion to predict the coupled nonlinear thermomechanical behavior. Static tensile load significantly affected the thermal expansion characteristics of the laminates tested. This effect is attributed to a fiber instability micromechanical behavior of the constituent materials. Analytical results correlated reasonably well with free thermal expansion tests (no load applied to the specimen). However, correlation was poor for tests with an applied load.

Farley, G. L.↗
NASA NTRS1987

SHARP simulation of discontinuities in highly convective steady flow

For steady multidimesional convection, the Quadratic Upstream Interpolation for Convective Kinematics (QUICK) scheme has several attractive properties. However, for highly convective simulation of step profiles, QUICK produces unphysical overshoots and a few oscillations, and this may cause serious problems in nonlinear flows. Fortunately, it is possible to modify the convective flux by writing the normalized convected control-volume face value as a function of the normalized adjacent upstream node value, developing criteria for monotonic resolution without sacrificing formal accuracy. This results in a nonlinear functional relationship between the normalized variables, whereas standard methods are all linear in this sense. The resulting Simple High Accuracy Resolution Program (SHARP) can be applied to steady multidimensional flows containing thin shear or mixing layers, shock waves, and other frontal phenomena. This represents a significant advance in modeling highly convective flows of engineering and geophysical importance. SHARP is based on an explicit, conservative, control-volume flux formation, equally applicable to one, two, or three dimensional elliptic, parabolic, hyperbolic, or mixed-flow regimes. Results are given for the bench-mark purely convective first-order results and the nonmonotonic predictions of second- and third-order upwinding.

Leonard, B. P.↗
NASA NTRS1988

Characterization of a turbomolecular-pumped magnetic sector mass spectrometer

A Perkin Elmer MGA-1200, turbomolecular-pumped, magnetic sector, multiple gas analyzer mass spectrometer with modified inlet for fast response was characterized for the analysis of hydrogen, helium, oxygen and argon in nitrogen and helium background gases. This instrument was specially modified for the Vanderberg AFB SLC-6 Hydrogen Disposal Test Program, as a part of the Hydrogen Sampling System (H2S2). Linearity, precision, drift, detection limits and accuracy among other analytical parameters for each of the background gas were studied to evaluate the performance of the instrument. The result demonstrates that H2S2 mass spectrometer is a stable instrument and can be utilized for the quantitative analytical determination of hydrogen, helium, oxygen and argon in nitrogen and helium background gases.

Mehta, Narinder K.↗
NASA NTRS1993

Overview of NASA's Adaptive Structures program

NASA's recent progress in Adaptive Structures is reviewed using results from both experimental and flight hardware test programs. Particular attention is given to testbeds, structural deployment/assembly, structural linearization, static shape/position adjustment, on-orbit system identification, and vibration suppression. It is concluded that a very rapid transition of research in Adaptive Structures to applications has occurred in the past five years. Adaptive Structures provide tools for increasing the robustness of structural design.

Venneri, S. L.↗
NASA NTRS1993

Turbine blade forced response prediction using FREPS

This paper describes a software system called FREPS (Forced REsponse Prediction System) that integrates structural dynamic, steady and unsteady aerodynamic analyses to efficiently predict the forced response dynamic stresses in axial flow turbomachinery blades due to aerodynamic and mechanical excitations. A flutter analysis capability is also incorporated into the system. The FREPS system performs aeroelastic analysis by modeling the motion of the blade in terms of its normal modes. The structural dynamic analysis is performed by a finite element code such as MSC/NASTRAN. The steady aerodynamic analysis is based on nonlinear potential theory and the unsteady aerodynamic analyses is based on the linearization of the non-uniform potential flow mean. The program description and presentation of the capabilities are reported herein. The effectiveness of the FREPS package is demonstrated on the High Pressure Oxygen Turbopump turbine of the Space Shuttle Main Engine. Both flutter and forced response analyses are performed and typical results are illustrated.

Murthy, Durbha, V.↗
NASA NTRS1994

Effect of radiance-to-reflectance transformation and atmosphere removal on maximum likelihood classification accuracy of high-dimensional remote sensing data

Many analysis algorithms for high-dimensional remote sensing data require that the remotely sensed radiance spectra be transformed to approximate reflectance to allow comparison with a library of laboratory reflectance spectra. In maximum likelihood classification, however, the remotely sensed spectra are compared to training samples, thus a transformation to reflectance may or may not be helpful. The effect of several radiance-to-reflectance transformations on maximum likelihood classification accuracy is investigated in this paper. We show that the empirical line approach, LOWTRAN7, flat-field correction, single spectrum method, and internal average reflectance are all non-singular affine transformations, and that non-singular affine transformations have no effect on discriminant analysis feature extraction and maximum likelihood classification accuracy. (An affine transformation is a linear transformation with an optional offset.) Since the Atmosphere Removal Program (ATREM) and the log residue method are not affine transformations, experiments with Airborne Visible/Infrared Imaging Spectrometer (AVIRIS) data were conducted to determine the effect of these transformations on maximum likelihood classification accuracy. The average classification accuracy of the data transformed by ATREM and the log residue method was slightly less than the accuracy of the original radiance data. Since the radiance-to-reflectance transformations allow direct comparison of remotely sensed spectra with laboratory reflectance spectra, they can be quite useful in labeling the training samples required by maximum likelihood classification, but these transformations have only a slight effect or no effect at all on discriminant analysis and maximum likelihood classification accuracy.

Hoffbeck, Joseph P.↗
NASA NTRS1960

Centrifuge Study of Pilot Tolerance to Acceleration and the Effects of Acceleration on Pilot Performance

A research program the general objective of which was to measure the effects of various sustained accelerations on the control performance of pilots, was carried out on the Aviation Medical Acceleration Laboratory centrifuge, U.S. Naval Air Development Center, Johnsville, PA. The experimental setup consisted of a flight simulator with the centrifuge in the control loop. The pilot performed his control tasks while being subjected to acceleration fields such as might be encountered by a forward-facing pilot flying an atmosphere entry vehicle. The study was divided into three phases. In one phase of the program, the pilots were subjected to a variety of sustained linear acceleration forces while controlling vehicles with several different sets of longitudinal dynamics. Here, a randomly moving target was displayed to the pilot on a cathode-ray tube. For each combination of acceleration field and vehicle dynamics, pilot tracking accuracy was measured and pilot opinion of the stability and control characteristics was recorded. Thus, information was obtained on the combined effects of complexity of control task and magnitude and direction of acceleration forces on pilot performance. These tests showed that the pilot's tracking performance deteriorated markedly at accelerations greater than about 4g when controlling a lightly damped vehicle. The tentative conclusion was also reached that regardless of the airframe dynamics involved, the pilot feels that in order to have the same level of control over the vehicle, an increase in the vehicle dynamic stability was required with increases in the magnitudes of the acceleration impressed upon the pilot. In another phase, boundaries of human tolerance of acceleration were established for acceleration fields such as might be encountered by a pilot flying an orbital vehicle. A special pilot restraint system was developed to increase human tolerance to longitudinal decelerations. The results of the tests showed that human tolerance of longitudinal deceleration forces was considerably improved through use of the special restraint system.

Creer, Brent Y.↗
NASA NTRS1993

Overhead and forward reach capability during exposure to +1 to +6 Gx loads

The lack of reach performance data obtained under space-flight conditions has led to questions regarding the operational impact of higher G loads on crew performance. This investigation studied the effect of increasing G loads on reach capability. Ten subjects were exposed in a stepwise fashion to increasing accelerations resulting in G loads of from +1 to +6 Gx in the Brooks AFB centrifuge. Four subjects wore the pre-Challenger Launch Entry Helmet (LEH) ensemble and six the current Launch Entry Suit (LES). The subjects performed standardized reach sweeps at each G level. These sweeps were recorded on videotape and subsequently analyzed using a 3-dimensional motion analysis system. Significant differences in forward and overhead reach were determined using the General Linear Models (GLM) procedure of the Statistical Analysis System (SAS) program. The results from this study suggest that purposeful movement can be realistically performed in the LEH at the 5 G level and in the LES up to the 4 G level.

G Suits/standards↗
NASA NTRS1993

Performance and mood-state parameters during 30-day 6 degrees head-down bed rest with exercise training

The study was designed to determine if performance and mood impairments occur in bed-rested subjects, and if different exercise-training regimens modify or prevent them. Eighteen normal, healthy men were divided on the basis of age, peak oxygen uptake, and maximal isometric knee extension strength into three similar groups: no exercise (NOE), isotonic exercise (ITE), and isokinetic exercise (IKE). A 15-min battery of 10 performance tests and 8 mood and 2 sleep scales were administered daily during ambulatory control, 30 d of absolute bed rest (BR), and 4 d of ambulatory recovery. Performance test proficiency increased (p < 0.05) for all three groups during BR in 7 of 10 tests and there were no consistent significant differences between the three groups. However, during BR, the ITE group was distinguished from the other groups by a decline (p < 0.05) in the activation mood dimension and in two of its constituent scales (motivation and concentration), and by improvement (p < 0.05) in the trouble-falling-asleep and psychological-tension scales. Since few deleterious changes in performance and mood occurred in the three groups and did not exceed baseline ambulatory levels, we conclude that mood and performance did not deteriorate in response to prolonged BR and were not altered by exercise training. However, the decline in activation mood scales in the ITE group may reflect overtraining or excess total workload in this group.

NASA Center ARC↗
NASA NTRS2005

Small Body GN&C Research Report: A Guidance and Control Technique for Small-Body Proximity Operations with Guaranteed Guidance Resolvability and Required Thruster Silent Time

The guidance and control (G&C) algorithms for enabling small-body proximity operations are developed by using a model predictive control approach along with a convexification of the governing dynamics, control constraints, and trajectory/state constraints. The open-loop guidance is solved ahead of time or in a resolvable, real-time manner through the use of PWG (Pseudo Way-point Generation), a technique developed in this research. The PWG scheme ensures required thruster silent times during trajectory maneuvers. The feedback control is implemented to track the PWG trajectories in a manner that guarantees the resolvability for the open-loop problem, enabling the ability to update the G&C in a model-predictive manner. The schemes incorporate gravity models and thruster ring times into discrete dynamics that are solved as a optimal control problem to minimize fuel consumption or thruster energy expenditure. The optimal control problem is cast as an LMI (Linear Matrix Inequality) and then solved through Semi-Definite Programming techniques in a computationally efficient manner that provides convergence and constraint guarantees.

guidance and control (G&C)↗
NASA NTRS2006

Rapid Aeroelastic Analysis of Blade Flutter in Turbomachines

The LINFLUX-AE computer code predicts flutter and forced responses of blades and vanes in turbomachines under subsonic, transonic, and supersonic flow conditions. The code solves the Euler equations of unsteady flow in a blade passage under the assumption that the blades vibrate harmonically at small amplitudes. The steady-state nonlinear Euler equations are solved by a separate program, then equations for unsteady flow components are obtained through linearization around the steady-state solution. A structural-dynamics analysis (see figure) is performed to determine the frequencies and mode shapes of blade vibrations, a preprocessor interpolates mode shapes from the structural-dynamics mesh onto the LINFLUX computational-fluid-dynamics mesh, and an interface code is used to convert the steady-state flow solution to a form required by LINFLUX. Then LINFLUX solves the linearized equations in the frequency domain to calculate the unsteady aerodynamic pressure distribution for a given vibration mode, frequency, and interblade phase angle. A post-processor uses the unsteady pressures to calculate generalized aerodynamic forces, response amplitudes, and eigenvalues (which determine the flutter frequency and damping). In comparison with the TURBO-AE aeroelastic-analysis code, which solves the equations in the time domain, LINFLUX-AE is 6 to 7 times faster.

Trudell, J. J.↗
NASA NTRSDate not supplied

MESA: Scalable Runtime Verification Tool Using Actors

This work presents our runtime verification approach implemented by the tool MESA (MEssage-based System Analysis) which allows for using concurrent monitors to check for properties specified in linear temporal logic and finite state machines.We employ the actor programing model to implement MESA where monitors are captured by concurrent actors that communicate via messaging. The paper also presents a case study where MESA is used to monitor flights in National Airspace System of United States using live air traffic data stream. The case study which motivated this work in the first place shows that our approach is effective.We also perform empirical study by conducting experiments using monitoring systems with different numbers of concurrent monitors and different layers of indexing.This paper describes our experiments, evaluates our results,and discusses challenges faced during the study. The evaluation shows our approach is scalable.

runtime verification, concurrency, actor programin↗
NASA NTRS2015

Antenna Characterization for the Wideband Instrument for Snow Measurements

Experimental characterization of the antenna for the Wideband Instrument for Snow Measurements (WISM) under development for the NASA Earth Science Technology Office (ESTO) Instrument Incubator Program (IIP), is discussed. A current sheet antenna, consisting of a small, 6x6 element, dual-linear polarized array with integrated beamformer, feeds an offset parabolic reflector, enabling WISM operation over an 8 to 40 GHz frequency band. An overview of the test program implemented for both the feed and the reflector antenna is given along with select results for specific frequencies utilized by the radar and radiometric sensors of the WISM.

Primary reflector↗
NASA NTRS2015

Antenna Characterization for the Wideband Instrument for Snow Measurements (WISM)

Experimental characterization of the antenna for the Wideband Instrument for Snow Measurement (WISM) under development for the NASA Earth Science Technology Office (ESTO) Instrument Incubator Program (IIP), is discussed. A current sheet antenna, consisting of a small, 6x6 element, dual-linear polarized array with integrated beamformer, feeds an offset parabolic reflector, enabling WISM operation over an 8 to 40 GHz frequency band. An overview of the test program implemented for both the feed and the reflector antenna is given along with select results for specific frequencies utilized by the radar and radiometric sensors of the WISM.

dual-polarized antenna↗
NASA NTRS2002

Process for a High Efficiency Class D Microwave Power Amplifier Operating in the S-Band

A process and product providing a High Efficiency Microwave Power Amplifier (HEMPA) which propagates S-Band microwave frequency square waves; utilizing a program simulating FETs at high DC-to-RF efficiencies, which analyses linear elements of selected FETs in a frequency domain, and non-linear elements of the FETs in a time domain, and converts the time domain values into the frequency domain, and performs DC and S-parameter simulated measurements based on predefined data for each FET. Individual FET parameters are extracted and isolated by converting the S-parameters to admittance or impedance parameters to derive FET models for each FET, which the program uses to provide a final output of a HEMPA circuit based on iterative simulations of an amplification circuit utilizing microwave topology and frequencies. Iterative simulations of the amplification circuit analyze output values of a plurality of cascaded stages of the FETs, which are arranged in a push-pull configuration.

William Herbert Sims, III↗
NASA NTRS2002

Third Generation RLV Structural Seal Development Programs at NASA GRC

NASA GRC's work on high temperature structural seal development began in the late 1980's and early 1990's under the NASP (National Aero-Space Plane) project. Bruce Steinetz led the in-house propulsion system seal development program and oversaw industry efforts for propulsion system and airframe seal development for this vehicle. a propulsion system seal location in the NASP engine is shown. The seals were located along the edge of a movable panel in the engine to seal the gap between the panel and adjacent engine sidewalls. More recently, we worked with Rocketdyne on high temperature seals for the linear aerospike engine ramps. In applications such as the former X-33 program, multiple aerospike engine modules would be installed side by side on the vehicle. Seals are required in between adjacent engine modules along the edges and base of the engines. The seals have to withstand the extreme temperatures produced byt he thrusters at the top of the ramps while accommodating large deflections between adjacent ramps. We came up with several promising seal concepts for this application and shared them with Rocketdyne.

Dunlap, Patrick H., Jr.↗