Search NASA⌕ Search

SEARCH · Search NASA

Results for “PERMANENT MAGNETS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Active magnetic regenerative cooling with smaller magnets

Magnetocaloric heat pumping near room temperature, a.k.a. magnetic cooling, relies on the active regenerator cycle to achieve functional temperature spans and realize economic and societal benefits promised by this emerging solid-state cooling technology. The cycle itself depends upon synchronizing oscillating flow of a heat transfer fluid through a solid porous active material matrix, or the refrigerant, with periods when the refrigerant is in the highest available (field-on) and in nearly zero (field-off) magnetic fields to accomplish heat transfer. With this in mind, in this work we analyze varying flow and magnetic field wave forms and the timing between when the fluid is pumped and when the magnetic field is turned on and off. We demonstrate that the volume and the cost of permanent magnet generating the field changes can be cut nearly in half with little to no effect on the device temperature span and cooling power normalized by the refrigerant mass.

36 MATERIALS SCIENCE↗
DOE OSTI2016

The radiofrequency magnetic dipole discharge

This paper describes a novel and simple concept of plasma source, which is able to produce a radiofrequency magnetized discharge with minimal power requirements. The source is based on the magnetron concept and uses a permanent magnet as an active electrode. The dipolar field produced by the magnet confines the electrons, which cause further ionization, thus producing a toroidally shaped plasma in the equatorial region around the electrode. A plasma can be ignited with such scheme with power levels as low as 5 W. Paschen curves have been built for four different working gases, showing that in Helium or Neon, plasma breakdown is easily obtained also at atmospheric pressure. The plasma properties have been measured using a balanced Langmuir probe, showing that the electron temperature is around 3–4 eV and higher in the cathode proximity. Plasma densities of the order of 10{sup 16 }m{sup −3} have been obtained, with a good positive scaling with applied power. Overall, the electron pressure appears to be strongly correlated with the magnetic field magnitude in the measurement point.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Giant Exfoliation Induced Magnetic Coercivity in Fe 3 GaTe 2

Permanent magnets with strong anisotropy and high coercivity underpin modern information and energy technologies, yet rare-earth-free alternatives remain limited. Here, we show that thickness engineering via mechanical exfoliation induces hard magnetic behavior in the van der Waals ferromagnet Fe 3 GaTe 2 . Bulk crystals exhibit Curie temperatures above 350 K but negligible room-temperature coercivity. When thinned below ∼100 nm, the coercive field is dramatically enhanced, reaching nearly 1 T at room temperature for in-plane fields—comparable to conventional hard magnets. Micromagnetic analysis reveals a crossover in magnetization reversal from domain-mediated processes in bulk samples to quasi-coherent rotation in thin flakes, driven by increased effective anisotropy and suppressed domain formation. This thickness-dependent transition enables tuning of magnetic hardness without chemical modification. Combined with high saturation magnetization and robust room-temperature performance, Fe 3 GaTe 2 emerges as a promising rare-earth-free material for spintronic applications. Its layered structure further allows integration into van der Waals heterostructures, where large in-plane coercivity can stabilize magnetic states against perturbations and interlayer coupling, offering potential for high-density nonvolatile memory and domain-wall-based devices.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Applied magnetism: A supply-driven materials challenge

Permanent magnets are important in many green energy technologies including wind turbine generators and hybrid-electric vehicle motors. For these applications, volume and weight are important factors driving the overall design, and therefore a high energy density, or energy product, is an important figure of merit. This quantity defines the magnetic energy contained in a given volume of material, and so higher energy density magnets enable smaller, lighter applications. Currently, the most powerful magnets suitable for commercial purposes contain rare earth elements (REE), usually neodymium and dysprosium in the neodymium-iron-boride class of magnets. However, for select applications, often requiring high temperatures, samarium cobalt is the alloy of choice. These magnets have energy densities several times greater than their nearest non-REE-based competitor, which for some applications is the defining factor in creating a viable device. The global supply of these REE is overwhelmingly produced in China, which in 2015 mined more than ten times as much as the next largest producer (Australia). Such market domination effectively creates a single source of supply, leaving industries which rely on REE consumption susceptible to price shocks and supply disruptions of these critical materials. Furthermore, this supply sensitivity may act as a drag on the adaptation rate of green energy technologies, particularly for large-scale users.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Mechanically Robust High Magnetic Performance Sm-Co Sintered Magnets (Final Report)

Samarium-cobalt based permanent magnets (SmCo 5 and Sm 2 Co 17 ) have excellent magnetic properties, good corrosion resistance, and long-term thermal stability. Sm-Co sintered magnets have been widely used in electric machines, telecommunication, biomedical devices, and magnetic sensors. They are the most preferred magnets for high-temperature applications (200 - 550 °C). However, Sm-Co sintered magnets are brittle. They cannot be used for applications subjected to high stress, vibration, or mechanical shock. Sm-Co sintered magnets are prone to chipping, and fracture in the course of block magnet manufacturing, part machining, assembly, and operation. The brittleness leads to a magnet production loss of up to 20-30% in volume and imposes limitations on part size and shape. Developing mechanically robust high-performance Sm-Co sintered magnets is of great scientific and technical significance. This project is in response to the current market need for mechanically robust high magnetic performance Sm-Co sintered magnets and their novel manufacturing processes. The project will focus on scaling-up, validation, and technology maturation study of the mechanically tough high magnetic performance Sm-Co magnets developed by Ames Laboratory at a lab-scale with the collaboration of the industry partner Electron Energy Corporation (EEC).

36 MATERIALS SCIENCE↗
NASA NTRS1976

Viking magnetic properties investigation - Preliminary results

Three permanent-magnet arrays are aboard the Viking lander. By sol 35, one array, fixed on a photometric reference test chart on top of the lander, has clearly attracted magnetic particles from airborne dust; two other magnet arrays, one strong and one weak, incorporated in the backhoe of the surface sampler, have both extracted considerable magnetic mineral from the surface as a result of nine insertions associated with sample acquisition. The loose Martian surface material around the landing site is judged to contain 3 to 7 per cent highly magnetic mineral which, pending spectrophotometric study, is thought to be mainly magnetite.

Hargraves, R. B.↗
NASA NTRS1977

The Viking magnetic properties experiment - Primary mission results

Three permanent magnet arrays were mounted on each Viking lander: a strong array fixed on a photometric reference test chart on top of the landers; and two arrays, one strong and one weak, incorporated into the backhoe of the surface sampler. Some or all of the magnetic particles detected could be highly magnetic unoxidized mineral grains (metallic Fe, magnetite, pyrrhotite) forming the core beneath a reddish coating of limonite or hematite; or grains composed of gamma-Fe2O3, with and without other iron oxides; or igneous rock (or mineral particles) which consist of an admixture of unweathered silicate material or minerals with a significant fraction of highly magnetic phase, again with a reddish coating; they could be also igneous rock or mineral particles, intrinsically nonmagnetic, but having a reddish coating containing gamma-Fe2O3; or clay mineral particles which contain and/or are coated with Fe2O3, of which a substantial fraction is in the gamma-Fe2O3 form.

Hargraves, R. B.↗
NASA NTRS1993

High efficiency magnetic bearings

Research activities concerning high efficiency permanent magnet plus electromagnet (PM/EM) pancake magnetic bearings at the University of Maryland are reported. A description of the construction and working of the magnetic bearing is provided. Next, parameters needed to describe the bearing are explained. Then, methods developed for the design and testing of magnetic bearings are summarized. Finally, a new magnetic bearing which allows active torque control in the off axes directions is discussed.

Studer, Philip A.↗
DOE OSTI2014

Design of a new electron cyclotron resonance ion source at Oshima National College of Maritime Technology

A new electron cyclotron resonance ion/plasma source has been designed and will be built at Oshima National College of Maritime Technology by early 2014. We have developed an ion source that allows the control of the plasma parameters over a wide range of electron temperatures for material research. A minimum-B magnetic field composed of axial mirror fields and radial cusp fields was designed using mainly Nd-Fe-B permanent magnets. The axial magnetic field can be varied by three solenoid coils. The apparatus has 2.45 GHz magnetron and 2.5–6.0 GHz solid-state microwave sources.

43 PARTICLE ACCELERATORS↗
DOE OSTI2013

Exchange-spring mechanism of soft and hard ferrite nanocomposites

Graphical abstract: - Highlights: • Exchange-spring behaviour of soft and hard ferrites was studied. • XRD patterns indicated soft and hard ferrites as fcc and hcp structure. • Hysteresis loops indicate wide difference in coercivity of soft and hard phases. • Nanocomposites produced convex hysteresis loop characteristic of single-phase. - Abstract: The paper reports exchange-spring soft and hard ferrite nanocomposites synthesized by chemical co-precipitation with or without the application of ultrasonic vibration. The composites contained BaFe{sub 12}O{sub 19} as the hard phase and CoFe{sub 2}O{sub 4}/MgFe{sub 2}O{sub 4} as the soft phase. X-ray diffraction patterns of the samples in the optimum calcined condition indicated the presence of soft ferrites as face-centred cubic (fcc) and hard ferrites as hexagonal close packed (hcp) structure respectively. Temperature dependence of magnetization in the range of 20–700 °C demonstrated distinct presence of soft and hard ferrites as magnetic phases which are characterized by wide difference in magnetic anisotropy and coercivity. Exchange-spring mechanism led these nanocomposite systems to exchange-coupled, which ultimately produced convex hysteresis loops characteristic of a single-phase permanent magnet. Fairly high value of coercivity and maximum energy product were observed for the samples in the optimum calcined conditions with a maximum applied field of 1600 kA/m (2 T)

36 MATERIALS SCIENCE↗
DOE OSTI2018

Effect of Heat Treatment on Microstructure and Magnetic Properties of Ce-Doped NdFeB Ribbons

The substitution for Nd by abundant element cerium (Ce) is a practical way for the comprehensive utilization of rare earth resources in NdFeB permanent magnets. In this letter, we have prepared the Ce-doped NdFeB ribbons and conventional NdFeB ribbons by melt quenching method and investigated the effects of heat treatment on the crystallization behavior, microstructure, and magnetic properties of the alloy. The results show that: (1) The crystallization behavior and the microstructural changes of the (Nd,Ce)FeB magnets are similar to the conventional NdFeB magnet when heat treatment. In addition, the Ce{sub 2}Fe{sub 14}B phase has a significant effect on the properties of the whole magnets. (2)The NdFeB phase and CeFeB phase are relatively close to each other after being precipitated from the amorphous phase. The coupling effect between the two phases is strong enough to weaken the effect of the addition of Ce and making the properties of the NdFeB magnets to not reduce too much after adding Ce.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2015

Upgrade of the BATMAN test facility for H{sup −} source development

The development of a radio frequency (RF) driven source for negative hydrogen ions for the neutral beam heating devices of fusion experiments has been successfully carried out at IPP since 1996 on the test facility BATMAN. The required ITER parameters have been achieved with the prototype source consisting of a cylindrical driver on the back side of a racetrack like expansion chamber. The extraction system, called “Large Area Grid” (LAG) was derived from a positive ion accelerator from ASDEX Upgrade (AUG) using its aperture size (ø 8 mm) and pattern but replacing the first two electrodes and masking down the extraction area to 70 cm2. BATMAN is a well diagnosed and highly flexible test facility which will be kept operational in parallel to the half size ITER source test facility ELISE for further developments to improve the RF efficiency and the beam properties. It is therefore planned to upgrade BATMAN with a new ITER-like grid system (ILG) representing almost one ITER beamlet group, namely 5 × 14 apertures (ø 14 mm). Additionally to the standard three grid extraction system a repeller electrode upstream of the grounded grid can optionally be installed which is positively charged against it by 2 kV. This is designated to affect the onset of the space charge compensation downstream of the grounded grid and to reduce the backstreaming of positive ions from the drift space backwards into the ion source. For magnetic filter field studies a plasma grid current up to 3 kA will be available as well as permanent magnets embedded into a diagnostic flange or in an external magnet frame. Furthermore different source vessels and source configurations are under discussion for BATMAN, e.g. using the AUG type racetrack RF source as driver instead of the circular one or modifying the expansion chamber for a more flexible position of the external magnet frame.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2018

Influence of Temperature on Sr{sub 0.35}La{sub 0.40}Ca{sub .25}Fe{sub 11.6}Co{sub 0.4}O{sub 19} Hexagonal Ferrites Against Structural, Morphological and Magnetic Properties Prepared by Conventional Ceramic Reaction Methodology

Conventional Ceramic Reaction Methodology has been utilized for the preparation of M-type hexagonal ferrites of Sr{sub 0.35}La{sub 0.40}Ca{sub 0.25}Fe{sub 11.6}Co{sub 0.4}O{sub 19} magnets. X-ray diffraction has been performed for phase determination of the magnetic powders. At calcination temperatures ranging from 1220 to 1330 {sup ∘}C, the synchronize compost of the magnetic powders comprised of M-type hexagonal ferrites together with a small amount of impurity phase such as α-Fe{sub 2}O{sub 3} were co-existed. At calcination temperature above 1270 {sup ∘}C, single-phase M-type hexaferrites can be obtained. The particles seemed to be in a hexagonal plate-like mould which spread-out homogeneously were examined by field emission scanning electron microscopy. The magnetic edibility of the magnetic powders was intended by permanent magnetic measurement test equipment vibrating sample magnetometer. Magnetic properties, such as specific saturation magnetization, coercivity and remanence were temperature-dependent. However, with the increase of sintering temperature, i.e. above 1270 {sup ∘}C, saturation magnetization was increased while the coercivity showed reversed order.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Effects of tensile loading during annealing of alnico melt spun ribbons

Conventional magnetic annealing (MA) of the permanent magnet alloy alnico involves application of an external magnetic field at temperatures within the spinodal decomposition range. This field biases the growth of the Fe-Co rich, ferromagnetic α 1 -phase in an energetically favorable 〈001〉 direction in alignment with the applied field within an Al-Ni rich, paramagnetic α 2 -phase. Utilizing a magnetic field to bias the α 1 -phase may limit alnico from reaching theoretical coercivity due to (1) the field having maximum biasing ability at temperatures near the Curie temperature where large α 1 -phase nanorods form and (2) connectivity of the α 1 -phase occurs unavoidably during MA. Both decrease the effective shape anisotropy of the α 1 -phase, thereby reducing coercivity. Herein, we explore tensile-loading as a biasing mechanism to control and optimize the final alnico nanostructure beyond that achieved by MA. Two samples of melt-spun alnico were heat-treated at 860 °C for 5 minutes: one sample was subjected to 10 MPa tensile stress for comparison with a stress-free control sample. Structural and magnetic characterization revealed that the stress-annealed ribbon sample possessed expected phase assemblages, but was distinguished by a ∼2× larger grain diameter and an elongated anisotropic α 1 -phase within grains that were oriented to a shear stress along 〈001〉 directions at an angle of ∼45° relative to the loading direction. Both types of annealing produced a similar increase in the coercivity and remanence, but a decrease in saturation magnetization.

Rinko, E. A.↗
DOE OSTI2024

Magnetic Nanoparticle Extraction of Lithium from Produced Waters - CRADA 483 (Final Report)

The demand for lithium in the energy production industry is expected to increase sharply, development of simple and cost-effective techniques for lithium production and recovery from various lithium sources is essential. In this project, core/shell magnetic nanoparticles were successfully designed to selectively extract lithium from aqueous lithium sources as an extension of Pacific Northwest National Laboratory’s magnetic nanofluid extraction technology. The core/shell magnetic nanoparticles are composed of manganese oxide-based lithium ion sieve shells, which allow selective lithium uptake from brines with multiple coexisting ions, over iron oxide cores, which can respond to external magnetic fields for effective recovery and reuse of adsorbents from a liquid. The synthesized lithium ion-sieves and core/shell magnetic nanoparticles were characterized using several techniques to reveal their crystallinity and morphology. The lithium uptake properties of the lithium ion-sieves and core/shell magnetic nanoparticles were evaluated in terms of lithium adsorption capacity, removal percentage, selectivity, and cycling performance in simulated and natural brines. Magnetic properties of the core/shell magnetic nanoparticles were tested by measuring magnetic saturation, and magnetic response of colloidal solutions containing the core/shell magnetic nanoparticles was tested with permanent magnets.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Chemical Analysis of Fluorobenzenes via Multinuclear Detection in the Strong Heteronuclear J-Coupling Regime

Chemical analysis via nuclear magnetic resonance (NMR) spectroscopy using permanent magnets, rather than superconducting magnets, is a rapidly developing field. Performing the NMR measurement in the strong heteronuclear J-coupling regime has shown considerable promise for the chemical analysis of small molecules. Typically, the condition for the strong heteronuclear J-coupling regime is satisfied at µT magnetic field strengths and enables high resolution J-coupled spectra (JCS) to be acquired. However, the JCS response to systematic chemical structural changes has largely not been investigated. In this report, we investigate the JCS of C6H6−xFx (x = 0, 1, 2, …, 6) fluorobenzene compounds via simultaneous excitation and detection of 19F and 1H at 51.5 µT. The results demonstrate that JCS are quantitative, and the common NMR observables, including Larmor frequency, heteronuclear and homonuclear J-couplings, relative signs of the J-coupling, chemical shift, and relaxation, are all measurable and are differentiable between molecules at low magnetic fields. The results, corroborated by ab initio calculations, provide new insights into the impact of chemical structure and their corresponding spin systems on JCS. In several instances, the JCS provided more chemical information than traditional high field NMR, demonstrating that JCS can be used for robust chemical analysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1972

A magnetic mouse activity meter

Activity meter has been developed using Hall effect devices that record passage of selected groups of magnetically tagged mice. Two small permanent magnets are implanted in belly and back of selected mice and electronic circuits are activated as mice move between cages. System has advantage over tagging, detecting, and identification methods currently used.

Henry, J.↗
NASA NTRS2011

Non-Contact Thrust Stand Calibration Method for Repetitively-Pulsed Electric Thrusters

A thrust stand calibration technique for use in testing repetitively-pulsed electric thrusters for in-space propulsion has been developed and tested using a modified hanging pendulum thrust stand. In the implementation of this technique, current pulses are applied to a solenoidal coil to produce a pulsed magnetic field that acts against the magnetic field produced by a permanent magnet mounted to the thrust stand pendulum arm. The force on the magnet is applied in this non-contact manner, with the entire pulsed force transferred to the pendulum arm through a piezoelectric force transducer to provide a time-accurate force measurement. Modeling of the pendulum arm dynamics reveals that after an initial transient in thrust stand motion the quasisteady average deflection of the thrust stand arm away from the unforced or zero position can be related to the average applied force through a simple linear Hooke s law relationship. Modeling demonstrates that this technique is universally applicable except when the pulsing period is increased to the point where it approaches the period of natural thrust stand motion. Calibration data were obtained using a modified hanging pendulum thrust stand previously used for steady-state thrust measurements. Data were obtained for varying impulse bit at constant pulse frequency and for varying pulse frequency. The two data sets exhibit excellent quantitative agreement with each other as the constant relating average deflection and average thrust match within the errors on the linear regression curve fit of the data. Quantitatively, the error on the calibration coefficient is roughly 1% of the coefficient value.

Wong, Andrea R.↗