Search NASA⌕ Search

SEARCH · Search NASA

Results for “Recovery Testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Accounting for the effect of dislocation climb-mediated flow on the anisotropy and texture evolution of Mg alloy, AZ31B

The current study explores the role that dislocation climb has in mediating plasticity a Mg alloy at moderately elevated temperatures. Interrupted tensile tests were performed on samples of Mg alloy, AZ31B, sheet in the O temper condition over a range of strain rates (10 -5 to 10 -1 s -1 ) and temperatures (20–350°C) along the rolling and transverse directions. Experimental measurements of the resulting strain anisotropy and texture evolution were used as constraints during a parametric study employing a new crystal plasticity model (VPSC-CLIMB), which explicitly accounts for the kinematics of dislocation climb. The results reveal that the climb of basal (a) dislocations is not only important for dislocation recovery, but also demonstrate that climb accommodates a significant fraction of the strain in conditions where a power-law creep-type constitutive response prevails. This work does not discredit the notion that non-basal slip of (a) and (c+a) dislocations is important over a wide range of temperatures and strain rates. However, it demonstrates that the activation of dislocation climb as the mechanistic change within the power law regime provides an explanation for a wide range of observations, including the simultaneous reduction in strain anisotropy, slowed texture evolution, and rapid increase in strain rate sensitivity. Finally, it is hypothesized that these conclusions may even apply to cases in which grain boundary sliding and/or dynamic recrystallization are observed.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Recovery of Rare Earth Elements from Bioleachates by Precipitation

Rare earth elements are essential components in electronic devices, however because of the limited imports and mining capabilities in the US, recycling these rare earths is crucial. Common practices used to recover REEs including hydrometallurgy and pyrometallurgy are harmful to the environment. Bioleaching, a form of biohydrometallurgy, is an emerging process that uses organic acids synthesized by microorganisms and can leach REEs at comparable efficiencies to less environmentally conscious processes. Once the REEs are leached by the bio-lixiviant produced by microorganisms, the REEs are suspended in the solution and need to precipitate out in order to be harvested for reuse. Common chemicals used for rare earth precipitation in hydrometallurgy processes include sodium sulfate and oxalic acid. These two reagents were tested at varying stoichiometric excess concentrations in bio-leachate derived from smart phone speaker magnets and bio-lixiviant. Following the precipitation reactions, it was observed that the oxalic acid reaction precipitated an abundance of iron (II) oxalate, an REE contaminate. This is most likely due to the bio-leachate having a higher pH compared to the hydrometallurgical leachates. Therefore, it was determined that sodium sulfate is a better candidate for REE precipitation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Design and evaluation of a dilute flow particle-to-air heat exchanger for energy storage applications

The use of inert and redox-active particles for high-temperature energy storage requires the development of components that can efficiently transfer energy to high-pressure working fluids like supercritical carbon dioxide (sCO 2 ). Dilute flow reactors can enable high working fluid outlet temperatures and minimal parasitic losses compared to moving packed bed and fluidized bed reactors. This research uses both computational and experimental methods to explore the design trade-offs and practical challenges of a novel component for transferring energy from dilute flows of hot, reduced metal oxide (MO x ) particles to sCO 2 in tubes. A discretized thermal resistance network model, which accounts for particle hydrodynamics, multi-mode heat transfer, and reaction equilibrium, guides the design of a prototype device. This device is experimentally tested with a surrogate heat transfer fluids and inert particle temperatures up to 400°C and a heat duty exceeding 1 kW. The data are used to validate the thermal hydraulic sub-models, allowing for the simulation of reacting particle scenarios. Under nominal design conditions, the flow rate of reactive particles is predicted to be 30% lower than that of inert particles for the same energy recovered, with over 70% of the stored particle energy transferred to the sCO 2 . Furthermore, these findings can inform the design of more efficient energy recovery reactors for particle-based systems and can be integrated into system-level concentrated solar power models with thermal storage to optimize operating conditions.

14 SOLAR ENERGY↗
DOE OSTI2023

Development of process parameters and post-build conditions for qualification of LPBF 316 SS

To harness the potential of laser powder bed fusion (LPBF) 316H stainless steel (SS) for use in advanced nuclear reactors, extensive research efforts are needed to develop optimal laser processing parameters and appropriate heat treatments, taking into account various manufacturing platforms and locations. Furthermore, it is crucial to assess the material properties in environments relevant to reactor operating conditions. In collaboration with Oak Ridge National Laboratory (ORNL) and Los Alamos National Laboratory (LANL), Argonne National Laboratory (ANL) is dedicated to gaining insights into how the manufacturing process and post-build treatments impact the performance of LPBF 316H SS. This report provides an overview of ANL's research findings for FY23, focusing on LPBF 316H SS produced using a Renishaw AM400 laser system. Specifically, our research has concentrated on three key areas: 1) Optimum laser processing parameters: Leveraging the high-throughput printing technology, we systematically varied the laser power, exposure time and point distance within the same build. By measuring the as-printed porosity, we identified an optimum printing parameter window that produced materials with near-complete density; 2) Post-built treatment development: Materials printed with the optimum laser parameters underwent treatments including stress relief, solution annealing, and hot isostatic pressing. Subsequently, we fabricated tension, creep, and fatigue specimens from materials subjected to these different conditions. Over the next year, a series of scoping tests will be conducted to facilitate the selection of the most suitable post-build treatment condition; 3) Thermal aging effects on microstructure and properties: thermal aging at 550°C, 650°C and 750°C was conducted on LPBF 316H SS specimens up to 2500 h. Microstructural characterization was performed with electron microscopy, and the evolution of the dislocation cell structures and secondary phases was studied. Microhardness tests and tension tests were conducted to quantify changes in mechanical properties. The results revealed that the aged LPBF 316H SS exhibited a high density of Cr-rich and Mo-rich fine precipitates within grains due to the presence of a high density of dislocations and the globally distributed dislocation cell structures, which served as heterogeneous nucleation sites for secondary phases. Along grain boundaries, a Mo-Cr-rich phase, observed in 750°C-aged conditions, displayed significant thermal coarsening. Throughout the aging process, various mechanisms, including stress relaxation, dislocation cell structure recovery, solution hardening, and precipitation hardening, competed to influence materials strength. These results contribute towards establishing the technical basis for qualifying LPBF 316H SS for advanced nuclear reactor applications.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Investigation of Stress Field and Fracture Development During Shale Maturation Using Analog Rock Systems

The emergence of hydrocarbons within shale as a major recoverable resource has sparked interest in fluid transport through these tight mudstones. Recent studies suggest the importance to recovery of microfracture networks that connect localized zones with large organic content to the inorganic matrix. This paper presents a joint modeling and experimental study to examine the onset, formation, and evolution of microfracture networks as shale matures. Both the stress field and fractures are simulated and imaged. A novel laboratory-scale, phase-field fracture propagation model was developed to characterize the material failure mechanisms that play a significant role during the shale maturation process. The numerical model developed consists of coupled solid deformation, pore pressure, and fracture propagation mechanisms. Benchmark tests were conducted to validate model accuracy. Laboratory-grade gelatins with varying Young’s modulus were used as scaled-rock analogs in two dimensional Hele-Shaw cell apparatus. Yeast within the gelatin generates gas in a fashion analogous to hydrocarbon formation as shale matures. These setups allow study and visualization of host rock elastic-brittle fracture and fracture network propagation mechanisms. The experimental setup was fitted to utilize photoelasticity principles coupled with birefringence properties of gelatin to explore visually the stress field of the gelatin as the fracture network developed. Stress optics image analysis and Linear Elastic Fracture Mechanics (LEFM) principles for crack propagation were used to monitor fracture growth for each gelatin type. Observed and simulated responses suggest gas diffusion within and deformation of the gelatin matrix as predominant mechanisms for energy dissipation depending on gelatin strength. LEFM, an experimental estimation of principal stress development with fracture growth, at different stages was determined for each gelatin rheology. Here, the interplay of gas diffusion and material deformation determines the resulting frequency and pattern of fractures. Results correlate with Young’s modulus. Experimental and computed stress fields reveal that fractures resulting from internal gas generation are similar to, but not identical to, type 1 opening mode.

58 GEOSCIENCES↗
DOE OSTI2022

MEASUR - Manufacturing Energy Assessment Software for Utility Reduction

MEASUR your energy savings with the free DOE MEASUR software The Department of Energy (DOE), with Oak Ridge National Laboratory (ORNL), released version 1.0 of their energy efficiency software tool MEASUR (Manufacturing Energy Assessment Software for Utility Reduction). MEASUR has been available for several years as a beta version, being tested by industry experts and real users, and will continue to be updated and improved in the coming years. It is an integrated suite of tools to aid manufacturers in improving the efficiency of energy systems and equipment within a plant, including motors, pumps, fans, process heating, steam, and compressed air. Additionally, there are modules for wastewater energy analysis and to help perform energy treasure hunts. Several calculators are also included, allowing users to independently perform smaller calculations and analyses (such as estimating pump head, performing a fan traverse analysis, estimating waste heat recovery potential, and cataloging compressed air leaks). The MEASUR modules are based on previous DOE software tools that have been used by industry since the early 2000s (such as MotorMaster, AirMaster+, PSAT, PHAST, and FSAT). The original tools only ran on Windows operating systems, and by Windows 10, most of them were inoperable. DOE started their energy efficiency software tool revitalization effort in 2016, first with PSAT (for pumps), then began to integrate the other tools and expand their functionality and utility. The new MEASUR suite provides an extensively more user-friendly, modern, and versatile set of tools. All the assessment modules and most of the calculators have several visual components and graphs and detailed help text for every user input. To help reach international users, the tool utilizes Google translate and users can easily change unit systems, even converting existing user inputs if desired. The assessment files can be organized within the internal file system and easily shared to other users, regardless of their operating system. The entire suite is free, open-source, and can be downloaded on Windows, Mac, or Linux operating systems.

Accawi, Gina [Oak Ridge National Lab. (ORNL), Oak ↗
DOE OSTI2023

Hybrid Heavy Duty Diesel Powertrain for Off-Road Applications (Final Technical/Scientific Report)

In this program, a heavy-duty hybrid powersystem, consisting of a 30% downsized diesel engine and a front-end accessory drive (FEAD) incorporating a high-speed flywheel (HSFW) energy storage system, a mechanical-drive turbocharger (SuperTurbo), and motor-generator units (MGU) was developed and demonstrated. The high efficiency core 13L engine coupled with the hybrid elements was physically validated across various off-road machine and transient work cycles with the ultimate goal of demonstrating 17% efficiency improvement with equivalent transient response as the 18L diesel engine this concept powersystem would replace. The project culminated in a physical demonstration of the high-efficiency powersystem in a high-capability test cell with the engine, all the hybrid devices, controls, and required performance and emissions measurements. Based on the combination of physical validation and rigorous system simulation, the following program conclusions may be drawn: (1) The developed hybrid H2D2 powersystem demonstrated a range of efficiency improvement of 10.5 - 25.6%, with a midpoint of 17.9%; (2) Transient load response on; (3) The HSFW system was validated to achieve peak assisting of 110kW at 12,000 Nm/sec ramp rates; (4) The powersystem was validated to be capable of meeting U.S. EPA Tier 4 Final off-road emissions through transient NRTC testing; (5) A Total Cost of Ownership (TCO) analysis and found that the core 13L engine would pay back immediately (adoption of start/stop would pay back in less than one year, and the full hybrid system payback was three years.)

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2023

Pyrolysis of Oils from Unconventional Resources

In this study, oils from various sources were subjected to pyrolysis conditions; that is, without oxidizer, as the samples were heated to 500 °C, and held at that temperature. The oils studied included: (1) heavy oil from Grassy Creek, Missouri; (2) oil from tar sands of Asphalt Ridge in Utah; (3) mid-continent oil shales of three formations (two of Chattanooga formation, Pennsylvanian (age) formation, and Woodford formation); and (4) a Colorado Piceance Basin shale. Differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) with either gas chromatography (GC) or mass spectrometry (MS) were used to quantify the produced gases evolved in the tests. Purge gases of helium, argon, and humid carbon dioxide were utilized. Larger scale pyrolysis tests were conducted in a tube furnace coupled to a MS and a GC. The results consistently showed that pyrolysis occurred between 300 °C and 500 °C, with the majority of gases being mainly hydrogen and light alkanes. This behavior was essentially consistent, regardless of the oil source.

42 ENGINEERING↗
DOE OSTI2020

Microfluidic Fabrication Techniques for High-Pressure Testing of Microscale Supercritical CO 2 Foam Transport in Fractured Unconventional Reservoirs

Pressure limitations of many microfluidic platforms have been a significant challenge in microfluidic experimental studies of fractured media. As a result, these platforms have not been fully exploited for direct observation of high-pressure transport in fractures. This work introduces microfluidic platforms that enable direct observation of multiphase flow in devices featuring surrogate permeable media and fractured systems. Such platforms provide a pathway to address important and timely questions such as those related to CO 2 capture, utilization and storage. This work provides a detailed description of the fabrication techniques and an experimental setup that may serve to analyze the behavior of supercritical CO 2 (scCO 2 ) foam, its structure and stability. Such studies provide important insights regarding enhanced oil recovery processes and the role of hydraulic fractures in resource recovery from unconventional reservoirs. This work presents a comparative study of microfluidic devices developed using two different techniques: photolithography/wet-etching/ thermal-bonding versus Selective Laser-induced Etching. Both techniques result in devices that are chemically and physically resistant and tolerant of high pressure and temperature conditions that correspond to subsurface systems of interest. Both techniques provide pathways to high-precision etched microchannels and capable lab-on-chip devices. Photolithography/wet-etching, however, enables fabrication of complex channel networks with complex geometries, which would be a challenging task for laser etching techniques. This work summarizes a step-by-step photolithography, wet-etching and glass thermal-bonding protocol and, presents representative observations of foam transport with relevance to oil recovery from unconventional tight and shale formations. In conclusion, this work describes the use of a high resolution monochromatic sensor to observe scCO 2 foam behavior where the entirety of the permeable medium is observed simultaneously while preserving the resolution needed to resolve features as small as 10 μm.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2018

Development of a mechanistic thermal aging model for Grade 91

This report provides a summary on understanding and predicting the effects of long-term thermal aging on microstructure and tensile properties of G91 to corroborate the ASME Code rules in strength reduction due to elevated temperature service. The research is to support the design and long-term operation of G91 structural components in sodium-cooled fast reactors (SFRs). The report is a Level 2 deliverable in FY18 (M2NT-18AN050502061), under the Work Package NT-18AN05050206, “G91 Code Extension Testing” performed by the Argonne National Laboratory (ANL), as part of the Advanced Materials Development Program for Fast Reactors. The thermal aging study of G91 involves three types of thermally-aged specimens: (1) specimens machined from two heats of G91, G91-H1 and H30176 that have been tested for the Advanced Materials Development Programs in the past years. These specimens were aged at 550, 600, and 650°C for times up to ~64,000 h; (2) specimens fabricated from the heads of the archived crept specimens (13 in total) of six heats of G91, H5349, H30394, H30383, H10148, H30176. These specimens were aged at 427 - 538°C and for times up to 132,647 h; (3) specimens made from a tube removed from the Kingston coal-fired power plant after exposure for 155,000 h at 550°C. These three sets of specimens provide a comprehensive data set for understanding and predicting the effect of long-term thermal aging on microstructure and tensile properties of G91. Microstructural analysis of the thermally-aged G91 revealed that thermal aging causes significant microstructural changes: (1) the tempered martensite formed during tempering is unstable, and suffers significant recovery during aging, manifested by an increase in subgrain width, a decrease in subgrain length, and a decrease in subgrain aspect ratio (i.e. subgrains become more equiaxed) as the aging temperature and time increase. The subgrain recovery is facilitated by the reduction of dislocation density within subgrains; (2) M23C6 carbides in the as-received G91 are distributed along grain and subgrain boundaries and play an important role as pinning obstacles against subgrain coarsening. M23C6 carbides coarsen during aging, and the coarsening of M23C6 carbides reduces the pinning force on the boundaries; (3) MX carbonitrides in the as-received G91 are distributed uniformly within subgrains, providing the precipitation hardening effect. They coarsen with increasing aging temperature and time, but the coarsening rate is low; (3) a new phase, the Laves phase intermetallic forms during aging. The formation of the Laves phase removes the Mo solutes from the matrix, reducing the solid solution strengthening effect. The Laves phase particles grow rapidly once they are nucleated, and they precipitate primarily along boundaries. They may have a pinning effect on boundaries, but should provide little to the alloy strength. The evolution of each microstructural constituent during thermal aging can be well described by individual microstructural models. The estimated activation energy for MX coarsening was 175 kJ/mol, equivalent to the activation energy for boundary and core diffusion in a-Fe, while the estimated activation energy for subgrain coarsening was significantly lower, ~96 kJ/mol. Thermal aging of G91 results in the reduction in the yield stress and the ultimate tensile strength but has an insignificant effect on the uniform and total elongations. The reduction in tensile strength is more pronounced as the aging temperature and time increases. The in situ tensile tests with high-energy X-rays revealed that sub-boundary strengthening plays a dominant role, and the strengthening role of M23C6 particles may be accounted for by subgrian boundary hardening, and three strengthening mechanisms can be superimposed to describe the tensile strength of G91: subgrain boundary hardening, MX precipitation hardening, and Mo solid solution strengthening. A microstructure – strength model was establ

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2022

Effect of a nanoparticle on wettability alteration and wettability retainment of carbonate reservoirs

The oil recovery in many carbonate reservoirs is low due to oil-wetness and heterogeneity. In this study, nanoparticles are evaluated for altering the wettability of oil-wet limestones and their properties are compared with those of an anionic surfactant. A surface-modified silica nanoparticle (SiNP) with a negative zeta potential was found to be aqueous stable in brines. Wettability studies showed that the SiNP cannot change the wettability of an initially oil-wet calcite plate, but SiNP treated calcite surface can remain water-wet after aging in oil. Spontaneous imbibition tests confirmed the observations of wettability tests and showed that a SiNP treated carbonate core retained its water-wettability during oil injection and aging. The imbibition into a SiNP treated and oil aged core was comparable to that in a water-wet core. However, SiNP was not able to remove the oil layers in initially oil-wet cores and imbibe water into these cores. In contrast, the anionic surfactant could alter the oil-wet carbonate rocks to a more water-wet condition, but failed to prevent the water-wet surface from getting oil-wet during oil-aging. The results suggest that the SiNP can be injected into wettability-altered (water-wet) reservoirs/regions to help retain the water-wettability during the long-term oil production. The 0.5 wt% SiNP dispersions transported through 18 mD limestone cores without any plugging. The SiNP retention was measured to be 2.5 mg/m 2 , much higher than that of the anionic surfactant.

02 PETROLEUM↗
DOE OSTI2018

International Collaboration Activities on Disposal in Argillite R&D: DECOVALEX19 Task C – Geochemical and Reactive Transport Modeling

International collaborations on nuclear waste disposal R&D are an integral part of the Spent Fuel Waste Science and Technology (SFWST) campaign within the DOE Fuel Cycle and Technology (FCT) program. These partnerships with international repository R&D programs provide key opportunities to participate in experiments developing laboratory/field data (underground research laboratories (URL)) of engineered barrier system (EBS) interactions (e.g., near-field) and characterization of transport phenomena in the host rock (e.g., far-field). The results of these experiments are used in the evaluation of coupled processes and their representation via state-of-the-art simulation approaches to evaluate repository performance. During the thermal heating period, increases in temperature from radionuclide decay in the spent fuel (SF) waste canisters will increase temperature in the surrounding EBS driving chemical and transport processes in the near- and far-field domains of the repository. URL heater-tests for extended periods of times (e.g., years) provide key information and data on thermal effects affecting engineered barriers in response to temperature and water saturation levels. Groundwater interactions with cementitious barriers are also important to in-drift chemistry and EBS performance during post-closure. Descriptions of the various URL experiments for various disposal design concepts according to the host country repository program and relevance to the US program is given elsewhere (Birkholzer et al.,2017;Jové Col& et al., 2016). The DECOVALEX-2019 Task C involves collaboration with the GREET (Groundwater REcovery Experiment in Tunnel) at the Mizunami URL, Japan ,which targets the development of monitoring methodologies of groundwater in granitic rock with applications to THMC simulations (Iwatsuki et al., 2005;Iwatsuki et al.,2015,2017). Some of the goals of GREET is to conduct a facility-scale geochemical characterization study of short- and long-term effects of tunnel excavation activities, impacts on groundwater flow and transport, and influences on groundwater chemistry (Iwatsuki et al.,2015). The data obtained from these URL activities is then used in the development and evaluation of THC models to support post-closure safety and performance assessments of the repository environment.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Polar Bear™ – Innovative Capture of Storage Tank Vapors

Polar Bear™ is a patented technology developed by the Energy & Environmental Research Center (EERC) to capture storage tank vapors and eliminate methane emissions from upstream oil- and gas-producing facilities. Sparked by early commercial investment, the EERC licensed the technology and extended the intellectual property to storage tanks. Polar Bear™ is uniquely engineered and adapted to individual lower-producing facilities where there is otherwise no economic alternative for capturing tank vapors. A high number of small producing oil and gas wells are distributed across the country. The aggregate contributes to a significant volume of emissions. Because of the lack of economy of scale, gas volumes from these facilities are typically not recovered and contribute to methane emissions. Polar Bear™ provides a fit-for-purpose compression solution that addresses cost by reducing complexity with respect to conventional vapor recovery units and eliminating oil changes. Unique to Polar Bear™ is the capability to separate oxygenated gas from storage tank vapors. Storage tanks are designed to “breathe,” allowing gas to enter and escape during internal level and temperature changes. This infiltration of air into the tank headspace imparts undesirable oxygen content with respect to pipeline gathering. Polar Bear™ separates the vapor stream, allowing oxygen-rich gas to be used as fuel on-site while recovering the liquids-rich portion of the gas where oxygen content is minimized. A prototype system was tested to verify process models, evaluate operational performance, and advance the technology readiness level from 5 to 6. Results provide a good match between experimental measurements and process models, indicating the models are useful for future scale-up and field design. Various mixtures of nitrogen and liquefied petroleum gas were tested to understand the mass balance of nitrogen and how it relates to the potential control of oxygen content. Findings indicate that less than 2000 ppm of oxygen is likely to remain in the liquid portion of the gas in field applications. The research and development prepare the technology for field implementation to eliminate routine and fugitive methane emissions from storage tanks.

02 PETROLEUM↗
DOE OSTI2025

Self‐Healable Poly(ionic liquid) Copolymers Driven by Polar and Dipolar Forces

Abstract Commodity aliphatic and aromatic acrylic‐based copolymers self‐heal due to ubiquitouskey‐and‐lock,ring‐and‐lock, andfluorophilic‐σ‐lockvan der Waals (vdW) interactions. However, the role of these interactions in the presence of covalently copolymerized ionic liquid (IL) is not known. This study is driven by the hypothesis that covalently incorporated cation–anion pairs to form poly(ionic liquid) copolymers (PILCs) can perturb inter‐ or intra‐chain vdW interactions reflected in mechanical and electrical responses. To test this hypothesis, we synthesized a series of PILCs comprising of pentafluorostyrene (PFS) and imidazolium‐based IL monomers with variable‐length aliphatic tails (methyl and butyl). Using a combination of 2D 1 H‐ 1 H and 19 F ‐ 19 F NOESY NMR and FTIR measurements supplemented by molecular dynamic (MD) simulations, these studies demonstrate that preferentially alternating/random PILCs topologies facilitate self‐healing. The introduction of cation–anion moieties modifies thefluorophilic‐σ‐lockinteractions and, along with longer aliphatic tails ─(CH 2 ) 3 CH 3 covalently attached to the imidazolium cation, enhances cation‐anion mobility, thus faster recovery from mechanical damage occurs. These findings underline how precise control over dipolar and ionic interactions through copolymer composition enables self‐healing in PILCs. These insights may open pathways for designing sustainable, mechanically resilient materials for applications in energy storage and energy harvesting.

Chemistry↗
DOE OSTI2025

Chemically Recyclable Polyester Thermosets from Activated Adipic Acid and Renewable Polyols

This study outlines a method for producing chemically recyclable crosslinked polyesters using renewable polyols-glycerol and sorbitol-combined with adipic acid (AA), which is transformed/activated into a polyanhydride mixture prior to use. A three-step procedure has been designed: 1) an acid-catalyzed reaction of AA with nontoxic isopropenyl acetate or acetic anhydride to form a crosslinking mixture (CLM) made of adipic-acetic mixed polyanhydrides; 2) a solvent- and additive-free process where glycerol or sorbitol, or a combination thereof, is reacted with the CLM to achieve a prepolymer, and 3) a casting/molding of the liquid viscous prepolymer to yield a thermoset as the end product. Different thermosets (eight examples) are prepared by changing the reagents ratio. These solids are thoroughly characterized by tensile tests, DMA, high-resolution magic angle spinning and solid-state NMR, thermal gravimetric analysis, DSC, and fourier transformed infra red (FT-IR) spectroscopy. The formation of cross-linked polyesters is confirmed in all cases, but mechanical properties varied significantly from one specimen to another. Interestingly, a tensile strength up to 18 MPa-approximately an order of magnitude higher than similar polymers-is achieved when sorbitol and the CLM are used in a 1:1 wt% ratio. The chemical recycle of the resulting polymers is achieved via methanolysis with quantitative recovery of the monomeric units.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2018

Higher Order Mode Damping in a Five-cell Superconducting RF Cavity with a PBG Coupler Cell

We present a study of higher order mode (HOM) damping in the first multi-cell superconducting radio frequency (SRF) cavity with a photonic band gap (PBG) coupler cell. Achieving higher average beam currents is particularly desirable for future light sources and particle colliders based on SRF energy-recovery-linacs (ERLs). Beam current in ERLs is limited by the beam break-up instability, caused by parasitic HOMs interacting with the beam in accelerating cavities. A PBG cell incorporated in an accelerating cavity can reduce the negative effect of HOMs by providing a frequency selective damping mechanism, thus allowing significantly higher beam currents. The five-cell cavity with a PBG cell was designed and optimized for HOM damping. Monopole and dipole HOMs were simulated. The SRF cavity was fabricated and tuned. External quality factors for some HOMs were measured in a cold test. The measurements agreed well with the simulations.

43 PARTICLE ACCELERATORS↗
DOE OSTI2021

Regional seismic velocity changes following the 2019 M w 7.1 Ridgecrest, California earthquake from autocorrelations and P / S converted waves

SUMMARY We examine regional transient changes of seismic velocities generated by the 2019 Mw 7.1 Ridgecrest earthquake in California, using autocorrelations of moving time windows in continuous waveforms recorded at regional stations. We focus on traveltime differences in a prominent phase generated by an interface around 2 km depth, associated with transmitted Pp waves and converted Ps waves from the ongoing microseismicity. Synthetic tests demonstrate the feasibility of the method for monitoring seismic velocity changes. Taking advantage of the numerous aftershocks in the early period following the main shock, we obtain a temporal resolution of velocity changes up to 20 min in the early post-main-shock period. The results reveal regional coseismic velocity drops in the top 1–3 km with an average value of ∼2 per cent over distances up to 100 km from the Ridgecrest event. These average velocity drops are likely dominated by larger changes in the shallow materials and are followed by rapid recoveries on timescales of days. Around the north end of the Ridgecrest rupture and the nearby Coso geothermal region, the observed coseismic velocity drops are up to ∼8 per cent. The method allows monitoring temporal changes of seismic velocities with high temporal resolution, fast computation and precise spatial mapping of changes. The results suggest that significant temporal changes of seismic velocities of shallow materials are commonly generated on a regional scale by large events.

58 GEOSCIENCES↗