Search NASA⌕ Search

SEARCH · Search NASA

Results for “Reduced Defects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42

pnnl/galas

Codebase for analyzing large atomistic simulation results using graph analytics. Analysis of large molecular simulations is difficult due to size and memory constrains in commonly used analysis software. This code was developed to analyze an ~8 million atom polycrystalline Al system under shear, with a particular emphasis on identifying defect structures. This code applies graph theory to reduce the system to components of interest and applies associated algorithms to characterize these components.

Pope, Jenna (Bilbrey)↗

Record breaking solar cells: Zn x Cd( 1-x )Te graded bandgap nanoarrays

CdTe is the leading material for thin-film solar cells due to ease of processing and reduced cost. However, low conversion efficiencies due to defects in the material are still a problem in these devices. We propose implementing micro and nano-enabled pseudomorphic growth of ZnCdTe to dramatically increase the efficiency of CdTe solar cells. Simulations predict that defect-free films are possible in graded ZnCdTe nanoislands below 90 nm as well as 24 % efficient solar cells with the use of ZnCdTe grading. Selective growth of CdTe showed single grains when the island sizes decreased below 300 nm. The simulation and experimental results demonstrate for the first time the ability to use nanopatterned substrates to enhance uniformity and efficiency in CdTe thin film solar cells. More than 20 reports, presentations, and papers were produced as part of this work and the results from this project enabled UTEP and Sandia to secure to grants.

Cruz-Campa, Jose Luis↗

Out-of-Pile Testing of Radiation Hard Optical Fibers

The work detailed in this report was supported under the In-Pile Instrumentation program for FY19. The work was conducted by researchers at Boise State University (BSU) and Idaho National Laboratory (INL). This report describes the out-of-pile testing that has been conducted to help guide sensor design and data interpretation by providing a robust understanding of out-of-pile fiber optic performance under different environmental factors. Highlighted in this report are two test configurations, transmission testing of optical fibers over a range of temperatures, and tensile testing of optical fibers identified through prior research as having potential for in-core use. The transmission temperature testing is conducted with high spectral resolution to study the influence of elevated temperatures on transmission. This testing has been conducted from room temperature up to 800ºC. The transmission testing was conducted by BSU at the Fiber Laser and Integrated photonics Research (FLaIR) laboratory. This testing will allow separation of radiation and temperature effects during in-core testing and allow for a more thorough understanding of radiation effects on fiber sensors. The tensile testing of optical fibers was conducted to provide a baseline for the strength of fiber optics. The fragile nature of glass fibers is a limitation in the deployment of fiber optics. Furthermore, intrinsic fiber optic sensors such as Fiber Bragg Gratings (FBG) add defects or damaged areas to the fiber which reduce its strength and can lead to broken sensors if not handled with care. The thermo-mechanical test facility enables the ability to quantitatively measure the strength of fibers with and without FBG’s over a temperature range. This information will be used to determine which types of FBG’s, and other sensors, are likely to survive the installation process. These tests will also be used to characterize the potential measurement range of fiber based strain sensors. The tensile testing was completed at INL in the HTTL Fiber Optics and Ultrasonic Technologies (FOUT) laboratory. Pure silica core (PSC) optical fibers have been shown to perform well in harsh environments. Transmission testing and tensile testing showed little change in fiber dynamic strength and transmission with elevated temperatures. There was no significant weakening of the fiber for temperatures up to 200ºC. Transmission at 1550 nm (a common wavelength used for optical sensors) showed minimal changes up to 800ºC with some improvement after 12 hours of annealing at 800ºC. This indicates that PSC optical fiber is a good candidate for in-pile testing.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Accomplishments of Sandia and Kitware CMake/CTest/CDash Contract for (FY2017-2020)

We describe the accomplishments jointly achieved by Kitware and Sandia over the fiscal years 2016 through 2020 to benefit the Advanced Scientific Computed (ASC) Advanced Technology Development and Mitigation (ATDM) project. As a result of our collaboration, we have improved the Trilinos and ATDM application developer experience by decreasing the time to build, making it easier to identify and resolve build and test defects, and addressing other issues . We have also reduced the turnaround time for continuous integration (CI) results. For example, the combined improvements likely cut the wall clock time to run automated builds of Trilinos posting to CDash by approximately 6x or more in many cases. We primarily achieved these benefits by contributing changes to the Kitware CMake/CTest/CDash suite of open source software development support tools. As a result, ASC developers can now spend more time improving code and less time chasing bugs. And, without this work, one can argue that the stabilization of Trilinos for the ATDM platforms would not have been feasible which would have had a large negative impact on an important internal FY20 L1 milestone.

97 MATHEMATICS AND COMPUTING↗

Spin-forming Project Report

In a second development order, spin-forming equipment was again evaluated using the test shape, a hemispherical shell. In this second development order, pure vanadium and alloy titanium (Ti-6Al-4V) were spin-formed, as well as additional copper and 21-6-9 stainless. In the first development order the following materials had been spin-formed: copper (alloy C11000 ETP), 6061 aluminum, 304L stainless steel, 21-6-9 stainless steel, and tantalum-2.5% tungsten. Significant challenges included properly adjusting the rotations-per-minute (RPM), cracking at un-beveled edges and laser marks, redressing of notches, surface cracking, non-uniform temperature evolution in the titanium, and cracking of the tailstock. Lessons learned were that 300 RPM worked better than 600 RPM for most materials (at the feed rate of 800 mm/min); beveling the edges to lower the stress reduces edge cracking; notches, laser marks, or edge defects in the preform doom the process to cracking and failure; coolant is required for vanadium spin-forming; increasing the number of passes to nine or more eliminates surface cracking for vanadium; titanium develops a hot zone in front of the rollers; and the tailstock should be redesigned to eliminate the cylindrical stress concentrator in the center.

36 MATERIALS SCIENCE↗

Initial postbuckling analysis of elastoplastic thin-shear structures

The design of thin shell structures with respect to elastoplastic buckling requires an extended analysis of the influence of initial imperfections. For conservative design, the most critical defect should be assumed with the maximum allowable magnitude. This defect is closely related to the initial postbuckling behavior. An algorithm is given for the quasi-static analysis of the postbuckling behavior of structures that exhibit multiple buckling points. the algorithm based upon an energy criterion allows the computation of the critical perturbation which will be employed for the definition of the critical defect. For computational efficiency, the algorithm uses the reduced basis technique with automatic update of the modal basis. The method is applied to the axisymmetric buckling of cylindrical shells under axial compression, and conclusions are given for future research.

E G Carnoy↗

The utilization of an infrared imaging system as a cooling slot blockage detector in the inspection of a transpiration cooled nozzle

A comprehensive examination of the 8 foot temperature tunnel's transpiration cooled nozzle was completed using an infrared imaging radiometer to locate regions of cooling flow irregularities caused by obstruction of three or more adjacent cooling slots. Restrictions in the cooling flow were found and cataloged. Blockages found were due primarily to the presence of residual phosphoric acid being discharged from some of the cooling slots. This acid was used during construction of the nozzle components and was to have been purged prior to its delivery to the NASA Langley Research Center (LaRC). In addition, a radial displacement of one selection of discs located in the spool piece was inspected and cataloged for future reference. There did not seem to be a serious restriction of flow in this defect, but evidence from the infrared images indicated reduced slot activity within the gouge. The radiometer survey uncovered regions where closer inspection is recommended but did not cover the entire surface area of the three nozzle subsections due to equipment limitations. A list of areas with suspected problems is included in Appendix A.

Borg, Stephen E.↗

A Rocket Investigation of Mesospheric Eddy Diffusion Effects on Airglow and Oxygen Chemistry

A Terrier Orion rocket was launched at 0750 Z on 02/25/98 about seven minutes after the Clemson University chemical release rocket. Measurements made of the electron density by a dc probe calibrated by a capacitance probe showed several layers of electron density on a rocket ascent in the altitude range from 90 to 110 km. Rocket descent results showed several but not all of the ascent structure. From power spectral analysis of the measured electron densities, turbulent parameters are derived Measurements were made on rocket ascent and descent by an infrared radiometer of the OH Meinel (3-1) band and O2 singlet delta emissions. Profiles of the emissions are presented and discussed on both rocket ascent and descent an enhancement of the OH emission monitored by the OH radiometer was observed above 90 km. The glow was not defected by the O2 radiometer and was significantly reduced on rocket descent. Using these data and a mechanistic analysis, a profile proportional to atomic oxygen is obtained. This profile is compared to one from the ATOX probe on the rocket. A one-dimensional (1-D) photochemical model that solves the time-dependent continuity equations is used with the rocket data to investigate the odd-oxygen concentration in the near equatorial mesosphere.

Ulwick, James C.↗

Thermal Conductivity and Sintering Behavior of Advanced Thermal Barrier Coatings

Advanced thermal barrier coatings, having significantly reduced long-term thermal conductivities, are being developed using an approach that emphasizes real-time monitoring of thermal conductivity under conditions that are engine-like in terms of temperatures and heat fluxes. This is in contrast to the traditional approach where coatings are initially optimized in terms of furnace and burner rig durability with subsequent measurement in the as-processed or furnace-sintered condition. The present work establishes a laser high-heat-flux test as the basis for evaluating advanced plasma-sprayed and physical vapor-deposited thermal barrier coatings under the NASA Ultra Efficient Engine Technology (UEET) Program. The candidate coating materials for this program are novel thermal barrier coatings that are found to have significantly reduced thermal conductivities due to an oxide-defect-cluster design. Critical issues for designing advanced low conductivity coatings with improved coating durability are also discussed.

Zhu, Dongming↗

An Electron Backscatter Diffraction (EBSD)-Based Automated Tool for Ceramic Capacitor Grain Size Analysis

Ceramic capacitors continue to be recurring problem parts for NASA, despite best efforts to screen out potential defects and failures through environmental and electrical testing and nondestructive inspection techniques such as acoustic microscopy. The physical properties of ceramic capacitors necessitates thin dielectric layers capable of withstanding significant electric fields. Any defects in those ceramic layers can result in reduced insulation resistance failure modes including short circuit failures, so the quality and consistency of the dielectric material is critical. The size of the individual ceramic grains in the dielectric material is a critical parameter. However, judging “grain size” is not so simple—in a single capacitor there can be wide variation in grain sizes observed. It is theorized that by studying the grain size distributions of “known good” and “known bad” lots of capacitors, some conclusions could be drawn that would allow us to better predict to the reliability of future lots based on grain size distributions. The initial goal of this effort was to find or develop an automated tool that could inspect a capacitor and return grain size distribution results.

Robert Hodson↗

Coherent Erbium Spin Defects in Colloidal Nanocrystal Hosts

We demonstrate nearly a microsecond of spin coherence in Er 3+ ions doped in cerium dioxide nanocrystal hosts, despite a large gyromagnetic ratio and nanometric proximity of the spin defect to the nanocrystal surface. The long spin coherence is enabled by reducing the dopant density below the instantaneous diffusion limit in a nuclear spin-free host material, reaching the limit of a single erbium spin defect per nanocrystal. We observe a large Orbach energy in a highly symmetric cubic site, further protecting the coherence in a qubit that would otherwise rapidly decohere. Spatially correlated electron spectroscopy measurements reveal the presence of Ce 3+ at the nanocrystal surface, which likely acts as extraneous paramagnetic spin noise. Even with these factors, defect-embedded nanocrystal hosts show tremendous promise for quantum sensing and quantum communication applications, with multiple avenues, including core-shell fabrication, redox tuning of oxygen vacancies, and organic surfactant modification, available to further enhance their spin coherence and functionality in the future.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Radiation defect dynamics in 3 C -, 4 H -, and 6 H -SiC studied by pulsed ion beams

Radiation damage behavior of SiC depends on its lattice structure. Here, we use a pulsed-ion-beam method to study defect interaction dynamics in 6H-SiC and damage buildup in 4H- and 6H-SiC irradiated at 100 °C with 500 keV Ar ions. These results are compared with previously reported data for Ar-ion-irradiated 3C- and 4H-SiC. We find that, for these irradiation conditions, damage buildup in 3C- and 6H-SiC is statistically indistinguishable and is significantly more efficient than in 4H-SiC. Within a stimulated amorphization model, 4H-SiC is described by a reduced amorphization cross-section constant, while the point defect cluster production cross-section is the same (within experimental errors) for the three polytypes studied. Moreover, 4H-SiC exhibits slower defect relaxation dynamics than 3C- and 6H-SiC. These results clearly demonstrate the importance of the lattice structure in damage buildup and defect interaction dynamics in SiC.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Leveraging Automated Fiber Placement Computer Aided Process Planning Framework for Defect Validation and Dynamic Layup Strategies

Process planning represents an essential stage of the Automated Fiber Placement (AFP) workflow. It develops useful and efficient machine processes based upon the working material, composite design, and manufacturing resources. The current state of process planning requires a high degree of interaction from the process planner and could greatly benefit from increased automation. Therefore, a list of key steps and functions are created to identify the more difficult and time-consuming phases of process planning. Additionally, a set of metrics must exist by which to evaluate the effectiveness of the manufactured laminate from the machine code created during the Process Planning stage. Layup strategies, in addition to dog ears, stagger shifts, steering constraints, and starting points, represented the group of functions labeled as process optimization and ranked the highest in terms of priority for automation. The laminates resulting from the selected parameters are evaluated through the occurrences of principal defect metrics such as fiber gaps, overlaps, angle deviation and steering violations. This document presents an automated software solution to the layup strategy and starting point selection phase of process planning. A series of ply scenarios are generated with variations of these ply parameters and evaluated according to a set of metrics entered by the Process Planner. These metrics are generated through use of the Analytical Hierarchy Process (AHP), where relative importance between each of the fiber features are defined. The ply scenarios are selected which reduce the overall fiber feature scores based on the defects the Process Planner wishes to minimize.

HiCAM↗

Influences of buffer material and fabrication atmosphere on the electrical properties of CdTe solar cells

Abstract The electrical properties such as interface energy barriers, defect energy levels, and densities dictate the performance of thin film solar cells. Here, we show that these properties can be quantified in cadmium telluride (CdTe) thin‐film solar cells using admittance spectroscopy‐based techniques. Our results reveal that the electrical properties in CdTe thin‐film solar cells depend on both buffer material and the fabrication atmosphere. We find that only a negligible front contact barrier exists at the CdS/CdTe front junction regardless of the fabrication atmospheres, while an obvious front barriers are observed at the ZnMgO (ZMO)/CdTe junctions. Both CdS/CdTe and ZMO/CdTe solar cells exhibit back contact barrier. The energy level of defects is shallower in CdS/CdTe cells than in ZMO/CdTe cells. The fabrication atmosphere influences the electrical properties, i.e., an oxygen‐free atmosphere reduces the front and back barrier heights and lowers the energy level of defects. The results provide critical insights for understanding and optimizing the performance of CdTe thin‐film solar cells.

Awni, Rasha A.↗

The Effect of Oxygen Adsorption for Vacancy-Induced d{sup 0} Magnetism in HfO{sub 2} (110) Surface

Based on the density functional theory, we investigated the electronic structures and magnetic properties of the oxygen adsorption on the defective cubic HfO{sub 2} (110) surface. The adsorption capacities of the perfect and defective surfaces follow in the sequence as: oxygen-deficient model >perfect surface >hafnium-deficient model. When the oxygen molecules adsorb on the nonmagnetic perfect HfO{sub 2} surface, the system has a local magnetic moment and the antiferromagnetic coupling is more stable. For the defective cubic HfO{sub 2} (110) surface, it is found that the oxygen vacancy is more easy to form than the hafnium vacancy by comparing the vacancy formation energy. And the hafnium vacancy could induce a large magnetic moment while the oxygen vacancy alone could not. After adsorption of the oxygen molecule, the nonmagnetic oxygen-deficient HfO{sub 2} model is transformed into the magnetic surface. On the contrary, the introduction of adsorbed oxygen molecule causes the magnetic moment of hafnium-deficient HfO{sub 2} surface to reduce. Additionally, if the oxygen molecules adsorb on the defective HfO{sub 2} (110) surface, the ferromagnetic coupling is energetically favorable.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Advanced Image Processing for Defect Visualization in Infrared Thermography

Results of a defect visualization process based on pulse infrared thermography are presented. Algorithms have been developed to reduce the amount of operator participation required in the process of interpreting thermographic images. The algorithms determine the defect's depth and size from the temporal and spatial thermal distributions that exist on the surface of the investigated object following thermal excitation. A comparison of the results from thermal contrast, time derivative, and phase analysis methods for defect visualization are presented. These comparisons are based on three dimensional simulations of a test case representing a plate with multiple delaminations. Comparisons are also based on experimental data obtained from a specimen with flat bottom holes and a composite panel with delaminations.

Plotnikov, Yuri A.↗

Voluntary Consensus Organization Standards for Nondestructive Evaluation of Thin-Walled Metallic Liners and Composite Overwraps in Composite Overwrapped Pressure Vessels

NASA fracture control requirements outlined in NASA-STD-5009 and NASA-STD-5014 are predicated on the availability and use of sensitive nondestructive evaluation (NDE) methods that can detect and monitor defects, thereby providing data that can be used to predict failure or reduce the risk of failure in fracture critical components. However, in the case of composite materials and components, including composite overwrapped pressure vessels (COPVs), the effect of defects is poorly understood, the NDE methods used to evaluate locate and size defects are typically at lower technical readiness level than analogous NDE methods used for metals, and demonstration studies to verify the probability of detection (POD) are generally lacking or unavailable. These factors together make failure prediction of fracture critical composite materials and components based on size, quantity, or orientation of defects nearly impossible. Also, when inspecting metal liners in as-manufactured COPVs, sensitivity is lost and only the inner surface of the liner is accessible. Also, NDE of COPVs as applied during manufacturing varies significantly from manufacturer to manufacturer and has not yet been standardized. Although requirements exist to perform NDE immediately after manufacturing to establish initial integrity of the parts, procedural detail for NDE of composites is still nonexistent or under development. For example, in practice, only a visual inspection of COPVs is performed during manufacturing and service, leaving in question whether defects of concern, for example, bridging, overwrap winding anomalies, impact damage below visible threshold, out-of-family strain growth, and liner buckling have been adequately detected and monitored. To address these shortcomings, in 2005 the NASA Nondestructive Evaluation Working Group (NNWG) began funding work to develop and adopt standards for nondestructive evaluation of aerospace composites in collaboration with the American Society for Testing and Materials (ASTM) Committee E07 on Nondestructive Testing. Similarly, in 2006 the NASA Engineering and Safety Center (NESC) recommended that nondestructive evaluation methods that can predict composite failure in COPVs should be developed and verified, and integrated into the damage control plan for these vessels

Waller, Jess↗