Search NASA⌕ Search

SEARCH · Search NASA

Results for “SIGNAL REFLECTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42
All sourcesNASA NTRSDOE OSTI
NASA NTRS2019

Surface Polarized Reflectance Analysis For Aerosol Remote Sensing

We study the Earth surface polarized reflectance using data collected by a space-based lidar. Accurate modelling of the surface reflectance supports retrieval algorithm development for the current and future Earth Science missions. Strong polarization of the laser light from Cloud-Aerosol Transport System (CATS) instrument, operated in 2015-2017, and nighttime measurements yield higher signal-to-noise ratio for polarization compared to the previous analysis of reflected, initially unpolarized, solar light.

Earth surface polarized reflectance↗
NASA NTRS2000

Preliminary Results from the GPS-Reflections Mediterranean Balloon Experiment (GPSR MEBEX)

An experiment to collect bistatically scattered GPS signals from a balloon at 37 km altitude has been conducted. This experiment represented the highest altitude to date that such signals were successfully recorded. The flight took place in August 1999 over the Mediterranean sea, between a launch in Sicily and recovery near Nerpio, a town in the Sierra de Segura, Albacete province of Huelva, Spain. Results from this experiment are presented, showing the waveform shape as compared to theoretical calculations. These results will be used to validate analytical models which form the basis of wind vector retrieval algorithms. These algorithms are already being validated from aircraft altitudes, but may be applied to data from future spaceborne GPS receivers. Surface wind data from radiosondes were used for comparison. This experiment was a cooperative project between NASA, the IEEC in Barcelona, and the University of Colorado at Boulder.

Garrison, James L.↗
DOE OSTI2025

Virtual Critical Coupling in High-Power Resonant Systems

Power reflections are a fundamental challenge in high-power resonant systems, causing energy loss, limiting per- formance, and potentially damaging critical components. This problem is particularly acute in applications such as lower hybrid current drive (LHCD) for tokamak-based nuclear fusion, where efficient, stable power transfer to the plasma is paramount. In this work, we introduce and experimentally demonstrate the virtual critical coupling (VCC) mechanism, a nonmechanical method to achieve reflection-free excitation in high-power S-band resonators. VCC utilizes a temporally shaped excitation signal with a precise complex frequency, tailored to the resonator’s characteristics to enable complete energy absorption. Using a custom low-level RF system and a 5-MW S-band klystron, we conducted experiments from low power (32 mW) to high power (600 kW). Furthermore, the results demonstrate a greater than ninefold reduction in the reflection coefficient compared to conventional monochromatic excitation. This signal processing-based approach offers a robust path toward enhancing the efficiency and stability of high-power resonant systems, with significant implications for particle accelerators and the advancement of nuclear fusion energy.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1991

An ultrasonic technique to measure the depth of burn wounds in humans

Whenever ultrasound encounters discontinuity in its medium of propagation, some energy is reflected from the interface. Such reflections or echoes occur when incident energy encounters the front skin, viable/necrotic, and dermis/fat skin tissue interfaces. It was shown that the most probable cause of the viable/necrotic interface is the uncoiling of collagen in the necrotic tissue, which can cause a reflection at the viable/necrotic interface of approximately 10 percent of the wave amplitude, and is approximately the same as that from the other two interfaces noted. The instrument, still in the prototype stage, was designed to detect the various reflections from within the skin layer. It is shown that, by studying the timing between the various echoes, one can use ultrasound as an aid in diagnosing the depth of burned skin tissue in humans. The instrument is a 60-MHz A-scan unit, modified to more easily identify the echoes occurring within the short time interval during which the reflections are received from the skin layers. A high frequency unit was selected so that various transducers could be utilized to optimize the system. Signal conditioning circuits were modified and added to provide an adequate display of the principle reflections expected. The unit was successful in studying burned tissue in pigs and was recently used to study burn wounds in humans. Measurement techniques and preliminary results are presented.

Yost, William T.↗
DOE OSTI2022

Shade triggers posttranscriptional PHYTOCHROME-INTERACTING FACTOR-dependent increases in H3K4 trimethylation

The phytochrome (phy)-PHYTOCHROME-INTERACTING FACTOR (PIF) sensory module perceives and transduces light signals to direct target genes (DTGs), which then drive the adaptational responses in plant growth and development appropriate to the prevailing environment. These signals include the first exposure of etiolated seedlings to sunlight upon emergence from subterranean darkness and the change in color of the light that is filtered through, or reflected from, neighboring vegetation (“shade”). Previously, we identified three broad categories of rapidly signal-responsive genes: those repressed by light and conversely induced by shade; those repressed by light, but subsequently unresponsive to shade; and those responsive to shade only. Here, we investigate the potential role of epigenetic chromatin modifications in regulating these contrasting patterns of phy-PIF module-induced expression of DTGs in Arabidopsis (Arabidopsis thaliana). Using RNA-seq and ChIP-seq to determine time-resolved profiling of transcript and histone 3 lysine 4 trimethylation (H3K4me3) levels, respectively, we show that, whereas the initial dark-to-light transition triggers a rapid, apparently temporally coincident decline of both parameters, the light-to-shade transition induces similarly rapid increases in transcript levels that precede increases in H3K4me3 levels. Together with other recent findings, these data raise the possibility that, rather than being causal in the shade-induced expression changes, H3K4me3 may function to buffer the rapidly fluctuating shade/light switching that is intrinsic to vegetational canopies under natural sunlight conditions.

59 BASIC BIOLOGICAL SCIENCES↗
NASA NTRS1988

Simulation of ocean SAR images via phase history generation

A method for simulating an ocean synthetic-aperture radar (SAR) image is illustrated for a simple internal wave current pattern. The method calculates both the amplitude image and the radar signal history. The simulation model used consists of six stages. In the first stage, the full wave spectrum in two spatial coordinates is calculated from the wind speed and direction using the action spectral density equation. In the second stage, the pixel size is selected and used as the basis for dividing the spectrum into large and small scale motions. Realizations for the large-scale ocean surface height and velocity are then calculated. In the third stage, the sensor wavelength and geometry are used to calculate the small scale statistics (radar cross section, coherence time, root-mean square (RMS), radial velocity and RMS slope). In the fourth stage, an autoregressive method is used to generate a realization of the surface reflectivity history that is consistent with the radial velocity and the radial velocity variance. In the fifth stage, the signal history is generated by summing the reflectivities at the proper times with the appropriate antenna weighting function for the SAR. As a consequence of this process, speckle is automatically included in the signal. In the final stage, the SAR image can be created by using any of the traditional ways to process the signal history, including variable focusing and multilook processing.

Bennett, John R.↗
NASA NTRS1980

Dielectric-loaded waveguide circulator for cryogenically cooled and cascaded maser waveguide structures

A dielectrically loaded four port waveguide circulator is used with a reflected wave maser connected to a second port between first and third ports to form one of a plurality of cascaded maser waveguide structures. The fourth port is connected to a waveguide loaded with microwave energy absorbing material. The third (output signal) port of one maser waveguide structure is connected by a waveguide loaded with dielectric material to the first (input) port of an adjacent maser waveguide structure, and the second port is connected to a reflected wave maser by a matching transformer which passes the signal to be amplified into and out of the reflected wavemaser and blocks pumping energy in the reflected wave maser from entering the circulator. A number of cascaded maser waveguide structures are thus housed in a relatively small volume of conductive material placed within a cryogenically cooled magnet assembly.

Clauss, R. C.↗
NASA NTRS1988

Fiber optic sensors with internal referencing

The main problem with amplitude modulating type sensors is that any variation in the intensity of the optical signal which occurs throughout the sensing system is interpreted by the photodetector as resulting from the sensor itself and is reflected as an error in the sensed parameter. To account for these errors, a referencing technique with the signal and reference channels separated in the time domain over the same fiber link can be used. Selected sensing and signal processing techniques involving temporally separated signal and referencing channels are described. A transition from the time into the frequency domain is also discussed. Experimental data are presented.

Adamovsky, Grigory↗
NASA NTRS2013

Forward-Looking IED Detector Ground Penetrating Radar

There have been many developments of mine or metal detectors based on ground penetrating radar techniques, usually in hand-held or rover-mounted devices. In most mine or metal detector applications, conditions are in a stationary mode and detection speed is not an important factor. A novel, forward-looking, stepped-frequency ground penetrating radar (GPR) has been developed with a capability to detect improvised explosive devices (IEDs) at vehicular speeds of 15 to 20 mph (24 to 32 km/h), 10 to 20 m ahead of the vehicle, to ensure adequate time for response. The GPR system employs two horn antennas (1.7 to 2.6 GHz, 20 dBi) as transmit and receive. The detector system features a user-friendly instantaneous display on a laptop PC and is a low-power-consumption (3 W) compact system with minimal impact on vehicle operations. In practice, the whole GPR system and a laptop PC can be powered by plugging into a cigarette lighter of a vehicle. The stepped-frequency continuous-wave (CW) radar scans frequency from 1.7 to 2.6 GHz in 1,000 steps of 0.9 MHz, with the full frequency scan in 60 ms. The GPR uses a bi-static configuration with one horn antenna used as a transmitter and the other used as a receiver so that isolation between transmitter and receiver is improved. Since the horn antennas (20 dBi) are mounted on the roof of a vehicle at a shallow inclination angle (15 to 25 with respect to horizontal), there is a first-order reduction in ground reflection so that a significant amount of the total reflected power received by the GPR comes from the scattering of RF energy off of buried objects. The stepped-frequency technique works by transmitting a tone at a particular frequency, while the received signal is mixed with the transmitted tone. As a result, the output of the mixer produces a signal that indicates the strength of the received signal and the extent to which it is in phase or out of phase with the transmitted tone. By taking measurements of the phase relationship between the transmitted and received signals over a wide frequency range, an interference pattern is produced showing all target reflections. When a Fourier transform is performed on this pattern, the result is a time-domain representation of targets. Among the advantages of this technique over impulse radar is the ability to transmit and receive much more total energy, and to use non-damped, highly focused horn antennas. The novelty of the IED detector GPR has been achieved by miniaturization of GPR electronics (single electronics board, 10x5x2 cm), low power consumption (3 W), faster signal processing capability, and minimal impact on vehicle operations.

Kim, Soon Sam↗
DOE OSTI2022

Power Electronics Based Self-Monitoring and Diagnosing for Photovoltaic Systems

Faults in photovoltaic (PV) systems can seriously affect the efficiency, energy yield, cost, safety, and reliability of PV plants. Condition monitoring of PV plants is, therefore, a very important approach to estimating the health condition of PV modules and power electronics in the system. However, additional hardware for PV system monitoring adds cost to the system's operation; delayed maintenance service also causes additional energy production loss. The Center for Power Electronics Systems (CPES) at the Virginia Polytechnic Institute and State University and Siemens Cooperate Research developed the online impedance measurement for a PV panel self-monitoring and diagnosing technology using the DC-DC converter connected to the panel. Small-signal impedances of a monocrystalline silicon PV panel were modeled and simulated to reflect fault conditions such as the short-circuit, hot-spot, and junction box faults. Modeling and simulation results were validated firstly using a test setup consisting of a solar simulator, a network analyzer, small-signal injectors, and a monocrystalline PV panel rated at 300 W.

14 SOLAR ENERGY↗
DOE OSTI2016

INWARD MOTIONS IN THE OUTER SOLAR CORONA BETWEEN 7 AND 12 R {sub ⊙}: EVIDENCE FOR WAVES OR MAGNETIC RECONNECTION JETS?

DeForest et al. used synoptic visible-light image sequences from the COR2 coronagraph on board the STEREO-A spacecraft to identify inbound wave motions in the outer corona beyond 7 solar radii and inferred, from the observation, that the Alfvén surface separating the magnetically dominated corona from the flow dominated wind must be located beyond at least 12 solar radii from the Sun over polar coronal holes and beyond 15 solar radii in the streamer belt. Here, we attempt identification of the observed inward signal by theoretically reconstructing height-speed diagrams and comparing them to the observed profiles. Interpretation in terms of Alfvén waves or Alfvénic turbulence appears to be ruled out by the fact that the observed signal shows a deceleration of inward motion when approaching the Sun. Fast magnetoacoustic waves are not directly ruled out in this way, as it is possible for inward waves observed in quadrature, but not propagating exactly radially, to suffer total reflection as the Alfvén speed rises close to the Sun. However, the reconstructed signal in the height-speed diagram has the wrong concavity. A final possibility is decelerating reconnection jets, most probably from component reconnection, in the accelerating wind: the profile in this case appears to match the observations very well. This interpretation does not alter the conclusion that the Alfvén surface must be at least 12 solar radii from the photosphere. Further observations should help constrain this process, never identified previously in this way, in the distance range from 7 to 12 solar radii.

79 ASTRONOMY AND ASTROPHYSICS↗
NASA NTRS1973

Mariner 9 ultraviolet spectrometer experiment - Morning terminator observations of Mars

Mariner 9 ultraviolet morning terminator data indicate the presence of a high, optically thin scattering layer in the equatorial region of Mars extending to 50S. This is consistent with the afternoon terminator results, which showed the presence of a scattering layer for latitudes as far north as 50N. For both types of terminator observations, the magnitude of the reflectivity for large shadow heights and the apparent scale height of the signal are too large to be explained by a homogeneous atmosphere. The terminator observations poleward of 50S were modeled by a homogeneous atmosphere of molecular and particulate scatterers. As the lower atmosphere began to clear from the dust storm, a progressive change was noted in the magnitude of the terminator reflectivity which is attributed to a changing albedo for single scattering. The shape of the morning terminator reflectivity measured as a function of shadow height indicates larger apparent scale heights than were observed in the afternoon. The difference is attributed to an increase in thickness of the scattering layer during the night.

Ajello, J. M.↗
NASA NTRS1992

Aureole lidar: Design, operation, and comparison with in-situ measurements

In 1986, H. Berber and Hooper examined the signals that could be detected by an airborne lidar flying above the marine boundary layer (MBL). One signal (aureole) formed from laser light returned to the receiver after a reflect off the ocean and forward scatter off the aerosol particles appeared to be both detectable and related to the optical depth of the MBL. Now, research has been directed towards developing a practical instrument to measure the aureole and finding an algorithm to use the information. Unlike the lidar backscatter which typically requires a telescope with a narrow field of view (0.5 mrad), the aureole signal occurs over a wide field of view (50 mrad). To accommodate the totally different needs, a standard commercial Cassegrainian telescope was modified to yield a telescope with two focal planes. The secondary mirror was replaced by a lens, whose front surface was half silvered and curved to match the replaced mirror. Light reflecting off the lens focused behind the primary mirror. The back lens surface was curved to allow unreflected light to focus at the natural focus of the primary mirror. This focal plane which is behind the lens has a wide field of view. To calculate an extinction profile, the aureole optical depth estimate is combined with the lidar backscatter profile.

Hooper, William P.↗
NASA NTRS1983

Acoustooptic pulse-echo transducer system

A pulse-echo transducer system which uses an ultrasonic generating element and an optical detection technique is described. The transmitting transducer consists of a concentric ring electrode pattern deposited on a circular, X-cut quartz substrate with a circular hole in the center. The rings are independently pulsed with a sequence high voltage signals phased in such a way that the ultrasonic waves generated by the separate rings superimpose to produce a composite field which is focused at a controllable distance below the surface of the specimen. The amplitude of the field reflected from this focus position is determined by the local reflection coefficient of the medium at the effective focal point. By processing the signals received for a range of ultrasonic transducer array focal lengths, the system can be used to locate and size anomalies within solids and liquids. Applications in both nondestructive evaluation and biomedical scanning are suggested.

Claus, R. O.↗
DOE OSTI2022

Spectroscopic Investigation of Catalyst Inks and Thin Films Toward the Development of Ionomer Quality Control

As the production of polymer electrolyte fuel cells expands, novel quality control methods must be invented or adapted in order to support expected rates of production. Ensuring the quality of deposited catalyst layers is an essential step in the fuel cell manufacturing process, as the efficiency of a fuel cell is reliant on the catalyst layer being uniform at both the target platinum loading and the target ionomer content. Implementing a quality control method that is sensitive to these aspects is imperative, as wasting precious metals and other catalyst materials is expensive, and represents a potential barrier to entry into the field for manufacturers experimenting with novel deposition processes. In this work, we analyzed catalyst inks to determine if their ionomer content could be quantized spectroscopically. Attenuated total reflection (ATR) Fourier transform infrared spectroscopic technique was investigated producing a signal proportional to the ionomer content. ATR spectroscopy was able to quantitatively differentiate samples in which the ionomer to carbon mass ratio (I/C) varied between 0.9 and 3.0. The I/C ratio was correlated to the measured ATR signal near the CF 2 vibrational bands located between 1100 cm −1 and 1400 cm −1 . The experimental results obtained constitute a step toward the development of novel quality control methodologies for catalyst inks utilized by the fuel cell industry.

30 DIRECT ENERGY CONVERSION↗
NASA NTRS2000

Preliminary Results from the GPS-Reflections Mediterranean Balloon Experiment (GPSR-MEBEX)

An experiment to collect bistatically scattered GPS signals from a balloon at 37 km altitude has been conducted. This experiment represented the highest altitude to date that such signals were successfully recorded. The flight took place in August 1999 over the Mediterranean sea, between a launch in Sicily and recovery near Nerpio, a town in the Sierra de Segura, Albacete province of Huelva, Spain. Results from this experiment are presented, showing the waveform shape as compared to theoretical calculations. These results will be used to validate analytical models which form the basis of wind vector retrieval algorithms. These algorithms are already being validated from aircraft altitudes, but may be applied to data from future spacebourne GPS receivers. Surface wind data from radiosondes were used for comparison. This experiment was a cooperative project between NASA, the IEEC in Barcelona, and the University of Colorado at Boulder.

Garrison, James L.↗
NASA NTRS2018

ICESat-2 Photon Classification: Finding Signal Photons in the ATL03 Geolocated Photon Data Product

ICESat-2 carries NASA's next-generation laser altimeter, ATLAS, (Advanced Topographic Laser Altimeter System), designed to measure changes in ice sheet height, sea ice freeboard, and vegetation canopy height. ATLAS contains a photon-counting lidar which transmits green (532-nm) pulses at 10kHz. Each pulse is split into 3 pairs of beams (one strong and one weak). Approximately 1014 photons per pulse travel from ATLAS through the atmosphere to reflect off the Earth's surface. Some return back into the ATLAS telescope where they are recorded. Photons from sunlight and instrument noise at the same wavelength are also recorded. The flight software time tags all photons within a 500m to 6 km range window and generates histograms. Using the histograms, it selects a telemetry window which varies from 20m over flat surfaces to hundreds of meters over rougher terrain. ATL03 contains the time, height (relative to the WGS-84 ellipsoid), latitude and longitude of every photon within the telemetry window. The basic challenge is to determine which of these photons were reflected off the surface. We have developed an algorithm that identifies these signal photons and assigns a confidence level (low, medium, or high) to each signal photon based on the signal to noise ratio. We present an overview of the signal identification algorithm and show the results on actual ICESat-2 data over ice sheet, sea ice, vegetated, and water surfaces. Higher level ATLAS products work with aggregations of the photons in order to determine the ellipsoidal height of the Earth, canopy height and structure, and other quantities of geophysical interest.

Remote Sensing↗
NASA NTRS1994

Model for the Interpretation of Hyperspectral Remote-Sensing Reflectance

Remote-sensing reflectance is easier to interpret for the open ocean than for coastal regions because the optical signals are highly coupled to the phytoplankton (e.g., chlorophyll) concentrations. For estuarine or coastal waters, variable terrigenous colored dissolved organic matter (CDOM), suspended sediments, and bottom reflectance, all factors that do not covary with the pigment concentration, confound data interpretation. In this research, remote-sensing reflectance models are suggested for coastal waters, to which contributions that are due to bottom reflectance, CDOM fluorescence, and water Raman scattering are included. Through the use of two parameters to model the combination of the backscattering coefficient and the Q factor, excellent agreement was achieved between the measured and modeled remote-sensing reflectance for waters from the West Florida Shelf to the Mississippi River plume. These waters cover a range of chlorophyll of 0.2-40 mg/cu m and gelbstoff absorption at 440 nm from 0.02-0.4/m. Data with a spectral resolution of 10 nm or better, which is consistent with that provided by the airborne visible and infrared imaging spectrometer (AVIRIS) and spacecraft spectrometers, were used in the model evaluation.

Lee, Zhongping↗