Search NASA⌕ Search

SEARCH · Search NASA

Results for “Struts”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42

Characterization of the bending stiffness of large space structure joints

A technique for estimating the bending stiffness of large space structure joints is developed and demonstrated for an erectable joint concept. Experimental load-deflection data from a three-point bending test was used as input to solve a closed-form expression for the joint bending stiffness which was derived from linear beam theory. Potential error sources in both the experimental and analytical procedures are identified and discussed. The bending stiffness of a mechanically preloaded erectable joint is studied at three applied moments and seven joint orientations. Using this technique, the joint bending stiffness was bounded between 6 and 17 percent of the bending stiffness of the graphite/epoxy strut member.

Wu, K. Chauncey↗

O-ring sealing verification for the space shuttle redesign solid rocket motor

As a part of the redesign of the Space Shuttle Solid Rocket Motor, the field and nozzle-to-case joints were redesigned to minimize the dynamic flexure caused by internal motor pressurization during ignition. The O-ring seals and glands for the joints were designed to accommodate both structural deflections and to promote pressure assistance. A test program was conducted to determine if a fluorocarbon elastomeric O-ring could meet this criteria in the redesigned gland. Resiliency tests were used to investigate the O-ring response to gap motion while static seal tests were used to verify design criteria of pressure assistance for sealing. All tests were conducted in face seal fixtures mounted in servo-hydraulic test machines. The resiliency of the O-ring was found to be extremely sensitive to the effects of temperature. The External Tank/Solid Rocket Booster attach strut loads had a negligible affect on the ability of the O-ring to track the simulated SRB field joint deflection. In the static pressure-assisted seal tests, as long as physical contact was maintained between the O-ring and the gland sealing surface, pressure assistance induced instantaneous sealing.

Lach, Cynthia L.↗

Location of planar targets in three space from monocular images

Many pieces of existing and proposed space hardware that would be targets of interest for a telerobot can be represented as planar or near-planar surfaces. Examples include the biostack modules on the Long Duration Exposure Facility, the panels on Solar Max, large diameter struts, and refueling receptacles. Robust and temporally efficient methods for locating such objects with sufficient accuracy are therefore worth developing. Two techniques that derive the orientation and location of an object from its monocular image are discussed and the results of experiments performed to determine translational and rotational accuracy are presented. Both the quadrangle projection and elastic matching techniques extract three-space information using a minimum of four identifiable target points and the principles of the perspective transformation. The selected points must describe a convex polygon whose geometric characteristics are prespecified in a data base. The rotational and translational accuracy of both techniques was tested at various ranges. This experiment is representative of the sensing requirements involved in a typical telerobot target acquisition task. Both techniques determined target location to an accuracy sufficient for consistent and efficient acquisition by the telerobot.

Cornils, Karin↗

Design philosophy of long range LFC transports with advanced supercritical LFC airfoils

The achievement of 70 percent laminar flow using modest boundary layer suction on the wings, empennage, nacelles, and struts of long-range LFC transports, combined with larger wing spans and lower span loadings, could make possible an unrefuelled range halfway around the world up to near sonic cruise speeds with large payloads. It is shown that supercritical LFC airfoils with undercut front and rear lower surfaces, an upper surface static pressure coefficient distribution with an extensive low supersonic flat rooftop, a far upstream supersonic pressure minimum, and a steep subsonic rear pressure rise with suction or a slotted cruise flap could alleviate sweep-induced crossflow and attachment-line boundary-layer instability. Wing-mounted superfans can reduce fuel consumption and engine tone noise.

Pfenninger, Werner↗

Effect of leading edge sweep on shock-shock interference at Mach 8

These Mach 8 experimental results are applicable to the details of a shock-shock interference that may occur on an engine inlet of a hypersonic vehicle from a swept forebody shock interacting with a swept cowl leading edge bow shock or from a swept splitter plate shock interacting with a swept fuel injection strut bow shock. Peak surface pressure and heat transfer rate on the cylinder were about 10 and 30 times the undisturbed flow stagnation point value, respectively, for the 0 deg sweep test. A comparison of the 15 deg and 30 deg swept results with the 0 deg swept results shows that peak pressure was reduced about 13 percent and 44 percent, respectively, and peak heat transfer rate was reduced about 7 percent and 27 percent, respectively.

Glass, Christopher E.↗

Noise of a model counterrotation propeller with simulated fuselage and support pylon at takeoff/approach conditions

Two modern high-speed advanced counterrotation propellers, F7/A7 and F7/A3 were tested in the NASA Lewis Research Centers's 9- by 15-foot Anechoic Wind Tunnel at simulated takeoff/approach conditions of 0.2 Mach number. Both rotors were of similar diameter on the F7/A7 propeller, while the aft rotor diameter of the F7/A3 propeller was 85 percent of the forward propeller to reduce tip vortex-aft rotor interaction. The two propellers were designed for similar performance. The propellers were tested in both the clean configuration, and installed configuration consisting of a simulated upstream nacelle support pylon and fuselage section. Acoustic measurements were made with an axially translating microphone probe, and with a polar microphone probe which was fixed to the propeller nacelle and could make both sideline and circumferential acoustic surveys. Aerodynamic measurements were also made to establish propeller operating conditions. The propellers were run at blade setting angles (front angle/rear angle) of 41.1/39.4 deg for the F7/A7 propeller, and 41.1/46.4 deg for the F7/A3 propeller. The forward rotors were tested over a range of tip speeds from 165 to 259 m/sec (540 to 850 ft/sec), and both propellers were tested at the maximum rotor-rotor spacing, based on pitch change axis separation, of 14.99 cm (5.90 in.). The data presented in this paper are for 0 deg propeller axis angle of attack. Results are presented for the baseline, pylon-alone, and strut + fuselage configurations. The presence of the simulated fuselage resulted in higher rotor-alone tone levels in a direction normal to the advancing propeller blade near the fuselage. A corresponding rotor-alone tone reduction was often observed 180 deg circumferentially from this region of increased noise. A significant rotor-alone increase for both rotors was observed diametrically opposite the fuselage. In some cases, interaction tone levels were likewise affected by the simulated installation.

Woodward, Richard P.↗

Design aspects of long range supersonic LFC airplanes with highly swept wings

The achievement of natural LFC in SST configurations featuring externally braced, very highly swept, high structural aspect ratio wing planforms results in outstandingly high cruise L/D ratios while maintaining low sonic-boom overpressures. A conceptual design study has been conducted with a view to range capability maximization in SSTs. A three-body configuration employing a highly swept, strut-braced planform, in which a central fuselage and two smaller outboard bodies alleviate structural wing bending and torsion, is noted to allow further increases in wingspan and aspect ratio which commensurately reduce lift-induced wave-plus-vortex drag and volume-induced wave drag.

Pfenninger, Werner↗

Space Systems Integrated Simulation (SPASIS)

Complex program models everything on user-defined space station, from control gyros to mass effect of astronaut moving along strut. Other features include plume impingement, attitude control, propellant slosh, docking, and gravity.

Stecklein, J. M.↗

Long-range LFC transport

M = 0.83 Laminar Flow Control (LFC) transports, carrying large percentage payloads over a range of 20000 kilometers at cruise L/D's of 39 appear feasible with large space externally braced wings, external fuel pods, active controls, and 70 percent laminar flow on wing and tail surfaces, engine nacelles and struts, and a turbulent fuselage. A combination of a swept-forward inboard and a swept-back outer wing appears superior overall, especially for laminar flow and eliminating leading edge contamination probably caused by flyspecks and ice crystals. Wing divergence appears controllable by a combination of various methods. Wind-mounted superfans with extensive laminar flow on their nacelles appear practical. Their dominant tone noise is below the frequency range of the most strongly amplified TS-waves.

Pfenninger, Werner↗

Transient Pressure Test Article Test Program

The Transient Pressure Test Article (TPTA) test program is being conducted at a new test facility located in the East Test Area at the National Aeronautics and Space Administration's (NASA's) Marshall Space Flight Center (MSFC) in Huntsville, Alabama. This facility, along with the special test equipment (STE) required for facility support, was constructed specifically to test and verify the sealing capability of the Redesigned Solid Rocket Motor (RSRM) field, igniter, and nozzle joints. The test article consists of full scale RSRM hardware loaded with inert propellant and assembled in a short stack configuration. The TPTA is pressurized by igniting a propellant cartridge capable of inducing a pressure rise rate which stimulates the ignition transient that occurs during launch. Dynamic loads are applied during the pressure cycle to simulate external tank attach (ETA) strut loads present on the ETA ring. Sealing ability of the redesigned joints is evaluated under joint movement conditions produced by these combined loads since joint sealing ability depends on seal resilience velocity being greater than gap opening velocity. Also, maximum flight dynamic loads are applied to the test article which is either pressurized to 600 psia using gaseous nitrogen (GN2) or applied to the test article as the pressure decays inside the test article on the down cycle after the ignition transient cycle. This new test facility is examined with respect to its capabilities. In addition, both the topic of test effectiveness versus space vehicle flight performance and new aerospace test techniques, as well as a comparison between the old SRM design and the RSRM are presented.

Vibbart, Charles M.↗

A note on an acoustic response during an engine nacelle flight experiment

During a flight test study of the noise effects on laminar flow on the outside surface of a simulated engine nacelle, an intense acoustic response was observed. The aircraft speed at which this signal occurred and the frequency content of the signal fell within the test conditions of the experiment and had to be eliminated prior to continuing. The signal was identified as an aerodynamic excitation of an acoustic mode in the simulated by-pass duct of the nacelle. By modifying the trailing edges of the support struts of the nacelle, the aerodynamic excitation was changed enough to eliminate the resonant response of the offending duct modes, eliminating the unwanted acoustic problem.

Schoenster, James A.↗

Heavily loaded joints for assembling aerobrake support trusses

The major emphasis was to develop erectable joints for large aerobrake support trusses. The truss joints must be able to withstand the large forces experienced by the truss during the aero-pass, as well as be easily assembled and disassembled on orbit by astronauts or robots. Other important design considerations include; strength, stiffness, and allowable error in strut length. Six mechanical joint designs, as well as a seventh joint design, where a high strength epoxy is injected to make the connection rigid, are presented.

Bandel, Hannskarl↗

Design of a Thermal and Micrometeorite Protection System for an Unmanned Lunar Cargo Lander

The first vehicles to land on the lunar surface during the establishment phase of a lunar base will be unmanned lunar cargo landers. These landers will need to be protected against the hostile lunar environment for six to twelve months until the next manned mission arrives. The lunar environment is characterized by large temperature changes and periodic micrometeorite impacts. An automatically deployable and reconfigurable thermal and micrometeorite protection system was designed for an unmanned lunar cargo lander. The protection system is a lightweight multilayered material consisting of alternating layers of thermal and micrometeorite protection material. The protection system is packaged and stored above the lander common module. After landing, the system is deployed to cover the lander using a system of inflatable struts that are inflated using residual fuel (liquid oxygen) from the fuel tanks. Once the lander is unloaded and the protection system is no longer needed, the protection system is reconfigured as a regolith support blanket for the purpose of burying and protecting the common module, or as a lunar surface garage that can be used to sort and store lunar surface vehicles and equipment. A model showing deployment and reconfiguration of the protection system was also constructed.

Hernandez, Carlos A.↗

Apparatus for measuring high-flux heat transfer in radiatively heated compact exchangers

An apparatus is described which can deliver uniform heat flux densities of up to 80 W/sq cm over an area 7.8 cm x 15.2 cm for use in measuring the heat transfer and pressure drop in thin (6 mm or less), compact heat exchangers. Helium gas at flow rates of 0 to 40 kg/h and pressures to 6.9 MPa (1000 psi) is the working fluid. The instrumentation used in the apparatus and the methods for analyzing the data is described. The apparatus will be used initially to test the performance of prototype cooling jackets for the engine struts of the National Aerospace Plane (NASP).

Olson, Douglas A.↗

Transformational part-count in layered octahedral-tetrahedral truss configurations

The number of component part (nodes, struts and panels) termed part count, is an important factor in the design, manufacture, and assembly of modular space structures. Part count expressions are presented for a variety of profiles derived from the layered octahedral-tetrahedral truss configuration. Referred to as the tetrahedral truss in the NASA projects, this specific geometry has been used in several missions. The general expressions presented here transforms to others as one profile changes to another. Such transformational part count relations provide a measure of flexibility and generality, and may be useful when dealing with a wider range of geometric configurations.

Lalvani, Haresh↗

A multi-domain spectral computation of three-dimensional laminar horseshoe vortex flow using incompressible Navier-Stokes equations

Multidomain spectral methods are presently used to numerically simulate a strut-wall intersection's laminar horseshoe vortex flow through direct solution of the three-dimensional, incompressible, time-dependent Navier-Stokes equations. Direct expansion in Chebyshev polynomials and spectral element method spatial discretization of flow dependence are used to achieve high-order accuracy, and minimal dispersion errors. Low and moderate Reynolds number results are presented to illustrate the method application.

Tan, C. S.↗

Thrust Vector Control using movable probes

A study was undertaken to determine if movable probes or struts positioned in the nozzle can be used to provide Thrust Vector Control of the Space Shuttle Solid Rocket Booster. The study employed CFD to determine estimates of the shock standoff distance from the probe. An empirical correlation was used to construct the shock shape and the pressure distribution generated by the probe. The TVC performance for a single and multiple number of probes was then used to determine requirements for a maximum thrust angle offset of 7.5 degrees. Consideration was given to what materials would be suitable for the probe and if active cooling is required. Based on the performance analysis and thermal requirements, a Probe Thrust Vector Control (PTVC) system was sized. Indications are that a PTVC system weight is in the 1500 1bm weight range, compared to the existing weight of 7500 1bm for the SRB nozzle gimble system.

Cavalleri, Robert↗

Design and fabrication of an erectable truss for precision segmented reflector application

The design of a first generation, 4-meter-diameter, doubly-curved, tetrahedral support truss for precision parabolic reflector panels, incorporating joints specifically designed for on-orbit astronaut assembly, is presented. Operational and design features of the erectable joint are detailed. Methods used to achieve very accurate strut lengths are described. Initial static and dynamic truss test results are presented which demonstrate linear structural response and predictability. Truss surface accuracy, determined photogrammetrically, is shown to be within 0.003 inch (RMS) of design.

Bush, Harold G.↗