Search NASA⌕ Search

SEARCH · Search NASA

Results for “Threading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42

Post Irradiation Examination of Pressurized Water Reactor Stainless Steel Internal Components

Internal structural components of pressurized water reactors (PWR), such as baffle former bolts, are subjected to significant neutron irradiation and mechanical stresses at elevated temperatures during plant operation. Over the long operation of the power plant, these conditions lead to potential degradation and reduced load-carrying capacity of these bolts. To understand property degradation more fully, to confirm the results of experimental irradiation programs, and to predict operational lifetime performance of structural materials in internal components, post irradiation examination of harvested materials from operating nuclear reactors is required. In this work, two high fluence 316 stainless steel baffle former bolts were retrieved from a commercial Westinghouse two-loop downflow type PWR and then sectioned for analysis via mechanical testing and microstructural characterization. The irradiation damage fluctuated along the bolt length with damage levels from 15 to 41 displacements per atom with the bolt head receiving approximately twice the neutron damage levels as that of the bolt thread section. Mechanical testing evaluations showed extensive irradiation hardening and a sharp decrease in fracture toughness in all parts of the bolt, though with limited variation along the bolt length. Microstructural characterization using analytical scanning transmission electron microscopy and atom probe tomography showed significant radiation induced precipitation, segregation, and dislocation loop and cavity formation. However, unlike the mechanical behavior, there was considerable variation along the bolt length but opposite of what may be expected, with more precipitation and cavity formation in the bolt thread where the neutron radiation dose is less than in the bolt head where the neutron radiation dose is higher. The cause of this variation is likely due to gradients in temperature, neutron energy spectra, and gamma irradiation.

Lach, Tim↗

Structural breakdown in high power GaN-on-GaN p-n diode devices stressed to failure

The morphology of GaN-on-GaN vertical p-i-n diode devices after reverse-bias electrical stressing to breakdown has been investigated. All failed devices had irreversible structural damage, showing large surface craters that were ∼15–35 μm deep with lengthy surface cracks. Cross-sectional electron micrographs of failed devices showed substantial concentrations of threading dislocations around the cracks and near the crater surfaces. Progressive ion-milling across damaged devices revealed high densities of threading dislocations and the presence of voids beneath the surface cracks; these features were not observed in any unstressed devices. These results should serve as a useful reference for future reliability studies of vertical high-power GaN devices.

Peri, Prudhvi (ORCID:000000022338441X)↗

A convolution-superposition dose calculation engine for GPUs

Purpose: Graphic processing units (GPUs) are increasingly used for scientific applications, where their parallel architecture and unprecedented computing power density can be exploited to accelerate calculations. In this paper, a new GPU implementation of a convolution/superposition (CS) algorithm is presented. Methods: This new GPU implementation has been designed from the ground-up to use the graphics card's strengths and to avoid its weaknesses. The CS GPU algorithm takes into account beam hardening, off-axis softening, kernel tilting, and relies heavily on raytracing through patient imaging data. Implementation details are reported as well as a multi-GPU solution. Results: An overall single-GPU acceleration factor of 908x was achieved when compared to a nonoptimized version of the CS algorithm implemented in PlanUNC in single threaded central processing unit (CPU) mode, resulting in approximatively 2.8 s per beam for a 3D dose computation on a 0.4 cm grid. A comparison to an established commercial system leads to an acceleration factor of approximately 29x or 0.58 versus 16.6 s per beam in single threaded mode. An acceleration factor of 46x has been obtained for the total energy released per mass (TERMA) calculation and a 943x acceleration factor for the CS calculation compared to PlanUNC. Dose distributions also have been obtained for a simple water-lung phantom to verify that the implementation gives accurate results. Conclusions: These results suggest that GPUs are an attractive solution for radiation therapy applications and that careful design, taking the GPU architecture into account, is critical in obtaining significant acceleration factors. These results potentially can have a significant impact on complex dose delivery techniques requiring intensive dose calculations such as intensity-modulated radiation therapy (IMRT) and arc therapy. They also are relevant for adaptive radiation therapy where dose results must be obtained rapidly.

61 RADIATION PROTECTION AND DOSIMETRY↗

SU-E-T-04: 3D Printed Patient-Specific Surface Mould Applicators for Brachytherapy Treatment of Superficial Lesions

Purpose: Evaluate the feasibility of constructing 3D-printed patient-specific surface mould applicators for HDR brachytherapy treatment of superficial lesions. Methods: We propose using computer-aided design software to create 3D printed surface mould applicators for brachytherapy. A mould generation module was developed in the open-source 3D Slicer ( http://www.slicer.org ) medical image analysis platform. The system extracts the skin surface from CT images, and generates smooth catheter paths over the region of interest based on user-defined start and end points at a specified stand-off distance from the skin surface. The catheter paths are radially extended to create catheter channels that are sufficiently wide to ensure smooth insertion of catheters for a safe source travel. An outer mould surface is generated to encompass the channels. The mould is also equipped with fiducial markers to ensure its reproducible placement. A surface mould applicator with eight parallel catheter channels of 4mm diameters was fabricated for the nose region of a head phantom; flexible plastic catheters of 2mm diameter were threaded through these channels maintaining 10mm catheter separations and a 5mm stand-off distance from the skin surface. The apparatus yielded 3mm thickness of mould material between channels and the skin. The mould design was exported as a stereolithography file to a Dimension SST1200es 3D printer and printed using ABS Plus plastic material. Results: The applicator closely matched its design and was found to be sufficiently rigid without deformation during repeated application on the head phantom. Catheters were easily threaded into channels carved along catheter paths. Further tests are required to evaluate feasibility of channel diameters smaller than 4mm. Conclusion: Construction of 3D-printed mould applicators show promise for use in patient specific brachytherapy of superficial lesions. Further evaluation of 3D printing techniques and materials is required for constructing sufficiently thin, rigid and durable surface moulds suitable for clinical deployment.

60 APPLIED LIFE SCIENCES↗

MO-FG-202-08: Real-Time Monte Carlo-Based Treatment Dose Reconstruction and Monitoring for Radiotherapy

Purpose: This proof-of-concept study is to develop a real-time Monte Carlo (MC) based treatment-dose reconstruction and monitoring system for radiotherapy, especially for the treatments with complicated delivery, to catch treatment delivery errors at the earliest possible opportunity and interrupt the treatment only when an unacceptable dosimetric deviation from our expectation occurs. Methods: First an offline scheme is launched to pre-calculate the expected dose from the treatment plan, used as ground truth for real-time monitoring later. Then an online scheme with three concurrent threads is launched while treatment delivering, to reconstruct and monitor the patient dose in a temporally resolved fashion in real-time. Thread T1 acquires machine status every 20 ms to calculate and accumulate fluence map (FM). Once our accumulation threshold is reached, T1 transfers the FM to T2 for dose reconstruction ad starts to accumulate a new FM. A GPU-based MC dose calculation is performed on T2 when MC dose engine is ready and a new FM is available. The reconstructed instantaneous dose is directed to T3 for dose accumulation and real-time visualization. Multiple dose metrics (e.g. maximum and mean dose for targets and organs) are calculated from the current accumulated dose and compared with the pre-calculated expected values. Once the discrepancies go beyond our tolerance, an error message will be send to interrupt the treatment delivery. Results: A VMAT Head-and-neck patient case was used to test the performance of our system. Real-time machine status acquisition was simulated here. The differences between the actual dose metrics and the expected ones were 0.06%–0.36%, indicating an accurate delivery. ∼10Hz frequency of dose reconstruction and monitoring was achieved, with 287.94s online computation time compared to 287.84s treatment delivery time. Conclusion: Our study has demonstrated the feasibility of computing a dose distribution in a temporally resolved fashion in real-time and quantitatively and dosimetrically monitoring the treatment delivery.

60 APPLIED LIFE SCIENCES↗

Real-time Depth Sectioning: Isolating the Effect of Stress on Structure Development in Pressure-Driven Flow

Transient structure development at a specific distance from the channel wall in a pressure-driven flow is obtained from a set of real-time measurements that integrate contributions throughout the thickness of a rectangular channel. This 'depth sectioning method' retains the advantages of pressure-driven flow while revealing flow-induced structures as a function of stress. The method is illustrated by applying it to isothermal shear-induced crystallization of an isotactic polypropylene using both synchrotron x-ray scattering and optical retardance. Real-time, depth-resolved information about the development of oriented precursors reveals features that cannot be extracted from ex-situ observation of the final morphology and that are obscured in the depth-averaged in-situ measurements. For example, at 137 degrees C and at the highest shear stress examined (65 kPa), oriented thread-like nuclei formed rapidly, saturated within the first 7 s of flow, developed significant crystalline overgrowth during flow and did not relax after cessation of shear. At lower stresses, threads formed later and increased at a slower rate. The depth sectioning method can be applied to the flow-induced structure development in diverse complex fluids, including block copolymers, colloidal systems, and liquid-crystalline polymers.

43 PARTICLE ACCELERATORS↗

Composite entanglement topology and extensional rheology of symmetric ring-linear polymer blends

Extensive molecular simulations are applied to characterize the equilibrium dynamics, entanglement topology, and nonlinear extensional rheology of symmetric ring-linear polymer blends with systematically varied ring fraction ϕR. Chains with degree of entanglement Z≈14 are mixed to produce 10 well-entangled systems with ϕR varying from neat linear to neat ring melts. Z is large enough that except for very large ϕR, the rings are threaded by multiple linear chains in equilibrium. Primitive path analysis is used to visualize and quantify the structure of the composite ring-linear entanglement network. We measure the quantity of ring-linear threading and linear-linear entanglement as a function of ϕR and identify with simple arguments a ring fraction ϕR≈0.4 where the topological constraints of the composite entanglement network are maximized. These topological analyses are used to rationalize the ϕR-dependence of ring and linear chain dynamics, conformations, and rheology. Simulations of startup uniaxial elongation flows demonstrate the extensional stress overshoot observed in recent filament stretching experiments and characterize how it depends on the blend composition and entanglement topology. The overshoot is driven by an overstretching and recoil of ring polymers due to the convective unthreading of rings from linear chains.

O’Connor, Thomas C.↗

Mechanisms of defect formation in ingots of 4H silicon carbide polytype

The methods of optical microscopy and X-ray diffractometry have been used to study the features of defect structure in ingots of the SiC-4H polytype; the ingots have featured different diameters and have been grown by the modified Lely method on seeds with deviations of several degrees from the exact orientation (0001)C in the direction Left-Pointing-Angle-Bracket 112-bar0 Right-Pointing-Angle-Bracket (off-cut (0001) seeds). The slip bands observed in the crystals are extended along the [112-bar0] direction and correspond to the secondary slip system of threading dislocations a/3 Left-Pointing-Angle-Bracket 112-bar0 Right-Pointing-Angle-Bracket (1-bar100) for hexagonal close packing (HCP) crystals. Low-angle dislocation boundaries directed along [11-bar00] accommodate the disorientation of neighboring domains, which results from their mutual rotation around the [0001] axis. Enlargement of ingots leads to some increase in the dislocation density, mainly due to threading edge dislocations. The average density of micropipes is in the range of 5-20 cm{sup -2} and practically remains unchanged as the ingot size is increased.

36 MATERIALS SCIENCE↗

Investigations of nanodimensional Al{sup 2}O{sup 3} films deposited by ion-plasma sputtering onto porous silicon

The purpose of this study is the deposition of nanodimensional Al{sup 2}O{sup 3} films on the surface of nanoporous silicon and also fundamental investigations of the structural, optical, and morphological properties of these materials. Analyzing the results obtained here, it is possible to state that ultrathin nanostructured Al{sup 2}O{sup 3} films can be obtained in the form of threads oriented in one direction and located at a distance of 300–500 nm from each other using ion-plasma sputtering on a layer of porous silicon. Such a mechanism of aluminum-oxide growth is conditioned by the crystallographic orientation of the initial single-crystalline silicon wafer used to fabricate the porous layer. The results of optical spectroscopy show that the Al{sup 2}O{sup 3}/por-Si/Si(111) heterophase structure perfectly transmits electromagnetic radiation in the range of 190–900 nm. The maximum in the dispersion of the refractive index obtained for the Al{sup 2}O{sup 3} film grown on por-Si coincides with the optical-absorption edge for aluminum oxide and is located in the region of ∼5.60 eV. This fact is confirmed by the results of calculations of the optical-absorption spectrum of the Al{sup 2}O{sup 3}/por-Si/Si(lll) heterophase structure. The Al{sup 2}O{sup 3} films formed on the heterophase-structure surface in the form of nanodimensional structured threads can serve as channels of optical conduction and can be rather efficiently introduced into conventional technologies, which are of great importance in microelectronics and optoelectronics.

36 MATERIALS SCIENCE↗

Impact of growth and annealing conditions on the parameters of Ge/Si(001) relaxed layers grown by molecular beam epitaxy

Influence of the Ge layer thickness and annealing conditions on the parameters of relaxed Ge/Si(001) layers grown by molecular beam epitaxy via two-stage growth is investigated. The dependences of the threading dislocation density and surface roughness on the Ge layer thickness, annealing temperature and time, and the presence of a hydrogen atmosphere are obtained. As a result of optimization of the growth and annealing conditions, relaxed Ge/Si(001) layers which are thinner than 1 μm with a low threading dislocation density on the order of 10{sup 7} cm{sup –2} and a root mean square roughness of less than 1 nm are obtained.

36 MATERIALS SCIENCE↗

X-Ray Diffraction Analysis of Epitaxial Layers with the Properties of a Dislocation Filter

An approach to instant testing of epitaxial films with a sharp decrease in the threading dislocation density is proposed. High-resolution X-ray diffractometry, including reciprocal space mapping, has been used. The structure of GaAs/Si(001) heterosystems with low-temperature GaAs layers has been analyzed. A decrease in the density of threading dislocations in the GaAs film with the formation of a small-angle boundary has been detected.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Efficient Approximation Algorithms for Weighted $b$-Matching

We describe a half-approximation algorithm, b-Suitor, for computing a b-Matching of maximum weight in a graph with weights on the edges. b-Matching is a generalization of the well-known Matching problem in graphs, where the objective is to choose a subset of M edges in the graph such that at most a speci ed number b(v) of edges in M are incident on each vertex v. Subject to this restriction we maximize the sum of the weights of the edges in M. We prove that the b-Suitor algorithm computes the same b-Matching as the one obtained by the greedy algorithm for the problem. We implement the algorithm on serial and shared-memory parallel processors, and compare its performance against a collection of approximation algorithms that have been proposed earlier. Our results show that the b-Suitor algorithm outperforms the Greedy and Locally Dominant edge algorithms by one to two orders of magnitude on a serial processor. The b-Suitor algorithm has a high degree of concurrency, and it scales well up to 240 threads on a shared memory multiprocessor. The b-Suitor algorithm outperforms the Locally Dominant edge algorithm by a factor of fourteen on 16 cores of an Intel Xeon multiprocessor.

97 MATHEMATICS AND COMPUTING↗

Enhancing the Performance of Assisted Execution Runtime Systems through Hardware/Software Techniques

To meet the expected performance, future exascale systems will require programmers to increase the level of parallelism of their applications. Novel programming models simplify parallel programming at the cost of increasing runtime overheard. Assisted execution models have the potential of reducing this overhead but they generally also reduce processor utilization. We propose an integrated hardware/software solution that automatically partition hardware resources between application and auxiliary threads. Each system level performs well-defined tasks efficiently: 1) the runtime system is enriched with a mechanism that automatically detects computing power requirements of running threads and drives the hardware actuators; 2) the hardware enforces dynamic resource partitioning; 3) the operating system provides an efficient interface between the runtime system and the hardware resource allocation mechanism. As a test case, we apply this adaptive approach to STM2, an software transactional memory system that implements the assisted execution model. We evaluate the proposed adaptive solution on an IBMPOWER7 system using Eigenbench and STAMP benchmark suite. Results show that our approach performs equal or better than the original STM2 and achieves up to 65% and 86% performance improvement for Eigenbench and STAMP applications, respectively.

Kestor, Gokcen↗

WIREFRAME: Supporting Data-dependent Parallelism through Dependency Graph Execution in GPUs

GPUs lack fundamental support for data-dependent parallelism and synchronization. While CUDA Dynamic Parallelism signals progress in this direction, many limitations and challenges still re-main. This paper introducesWireframe, a hardware-software solution that enables generalized support for data-dependent parallelism and synchronization. Wireframe enables applications to naturally express execution dependencies across different thread blocks through a dependency graph abstraction at run-time, which is sent to the GPU hardware at kernel launch. At run-time, the hardware enforces the dependencies specified in the dependency graph through a dependency-aware thread block scheduler. Overall, Wireframe is able to improve total execution time up to 65.20% with an average of 45.07%.

Abdolrashidi, AmirAli↗

Spherical Region Queries on Multicore Architectures

In this short paper, we report the performance of multiple thread-parallel algorithms for spherical region queries on multicore architectures motivated by a challenging data analytics application in materials science. Performances of two tree-based algorithms and a naive algorithm are compared to identify the length scales at which these approaches perform optimally. The optimal algorithm is then used to scale the driving materials science application, which is shown to deliver over 17X speedup using 32 OpenMP threads on data sets containing many millions of atoms.

Lu, Hao↗

The Minos Computing Library: Efficient Parallel Programming for Extremely Heterogeneous Systems

Hardware specialization has become the silver bullet to achieve efficient high performance, from Systems-on-Chip systems, where hardware specialization can be ``extreme'', to large-scale HPC systems. As the complexity of the systems increases, so does the complexity of programming such architectures in a portable way. This work introduces the Minos Computing Library (MCL), as system software, programming model, and programming model runtime that facilitate programming extremely heterogeneous systems. MCL supports the execution of several multi-threaded applications within the same compute node, performs asynchronous execution of application tasks, efficiently balances computation across hardware resources, and provides performance portability. We show that code developed on a personal desktop automatically scales up to fully utilize powerful workstations with 8 GPUs and down to power-efficient embedded systems. MCL provides up to 17.5x speedup over OpenCL on NVIDIA DGX-1 systems and up to 1.88x speedup on single-GPU systems. In multi-application workloads, MCL dynamically resource allocation provides up to 2.43x performance improvement over manual, static allocation of computing resources.

Gioiosa, Roberto↗

Evaluation of OpenAI Codex for HPC Parallel Programming Models Kernel Generation

We evaluate AI-assisted generative capabilities on fundamental numerical kernels in high-performance computing (HPC), including AXPY, GEMV, GEMM, SpMV, Jacobi Stencil, and CG. We test the generated kernel codes for a variety of language-supported programming models, including (1) C++ (e.g., OpenMP [including offload], OpenACC, Kokkos, SyCL, CUDA, and HIP), (2) Fortran (e.g., OpenMP [including offload] and OpenACC), (3) Python (e.g., numpy, Numba, cuPy, and pyCUDA), and (4) Julia (e.g., Threads, CUDA.jl, AMDGPU.jl, and KernelAbstractions.jl). We use the GitHub Copilot capabilities powered by the GPT-based OpenAI Codex available in Visual Studio Code as of April 2023 to generate a vast amount of implementations given simple + + prompt variants. To quantify and compare the results, we propose a proficiency metric around the initial 10 suggestions given for each prompt. Results suggest that the OpenAI Codex outputs for C++ correlate with the adoption and maturity of programming models. For example, OpenMP and CUDA score really high, whereas HIP is still lacking. We found that prompts from either a targeted language such as Fortran or the more general purpose Python can benefit from adding code keywords, while Julia prompts perform acceptably well for its mature programming models (e.g., Threads and CUDA.jl). We expect for these benchmarks to provide a point of reference for each programming model's community. Overall, understanding the convergence of large language models, AI, and HPC is crucial due to its rapidly evolving nature and how it is redefining human-computer interactions.

Godoy, William↗

Exploring Architectural-Aware Affinity Policies in Modern HPC Runtimes

Modern commodity and High-Performance Computing (HPC) systems are evolving with complex CPU architectures. These architectures now feature higher core and NUMA domain counts and implement features such as hyperthreading. When considering significant differences in hardware configurations, library availability, and hardware-tailored system/software stacks, which could substantially vary from one system to another, performance portability is hard to achieve. Throughout the years, this trend resulted in an increasingly high burden on application developers to fine-tune their workloads for each architecture. This work explores how hardware-dependent aspects such as locality/process/thread affinity affect performance in modern CPU architectures. We focus our study on the Global Memory and Threading (GMT) distributed runtime system as a representative of Partitioned Global Address Space (PGAS) software stacks commonly adopted for productivity. In particular, to appreciate performance implications, we evaluate GMT’s thread affinity policies, and, introduce two new ones which exploit architectural awareness. Finally, we explore alternative NUMA configurations via different process bindings and perform a scalability study on three HPC clusters with varying CPU architectures and NUMA layouts. Our analysis indicates that more complex architectures are more affected by affinity and binding policies and highlights the importance of setting proper runtime configurations to achieve superior performance.

Di Dio Lavore, Ian↗