Search NASA⌕ Search

SEARCH · Search NASA

Results for “dynamic experiments”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

A New Titanium-Bearing Calcium Aluminosilicate Phase: Meteoritic Occurrences and Formation in Synthetic Systems - 1

A new titanium-bearing calcium aluminosilicate mineral has been identified in coarse-grained calcium-aluminum-rich inclusions (CAIs) from carbonaceous chondrites. The formula for this phase, which we have temporarily termed "UNK," is Ca3Ti(AlTi)2(Si,Al)3O14, and it is present in at least 8 of the 20 coarse-grained CAIs from the Allende CV3 chondrite examined as part of this project. The phase occurs in Types A and B1 inclusions as small tabular crystals oriented along two mutually perpendicular planes in melilite. UNK crystallizes from melts in dynamic crystallization experiments conducted in air from four bulk compositions modeled after Types A, B1, B2 and C inclusions. Cooling rates resulting in crystallization of UNK ranged from 0.5 to 200 C/h from maximum (initial) temperatures of 1375 to 1580 C. Only below 1190 C does UNK itself begin to crystallize. To first order, the presence or absence of UNK from individual experiments can be understood in terms of the compositions of residual melts and nucleation probabilities. Compositions of synthetic and meteoritic LINK are very similar in terms of major oxides, differing only in the small amounts of trivalent Ti (7-13% of total Ti) in meteoritic samples. UNK crystallized from the Type A analog is similar texturally to that found in CAls, although glass, which is typically associated with synthetic UN& is not observed in meteoritic occurrences. A low Ti end-member of UNK ("Si-UNK") with a composition new that of Ca3Al2Si4O14 was produced in a few samples from the Type B1 analog. This phase has not been found in the meteoritic inclusions.

Paque, Julie M.↗
NASA NTRS2004

The Vaguries of Pyroxene Nucleation and the Resulting Chondrule Textures

Pyroxene is a major phase in chondrules, but often follows olivine in the crystallization sequence and depending on the melting temperature and time may not nucleate readily upon cooling. Dynamic crystallization experiments based on total or near total melting were used to study PO (porphyritic olivine) and PP (Porphyritic pyroxene) compositions as defined by. The experiments showed that pyroxene nucleated only at subliquidus temperatures in the PP melts and rarely in the PO melts. Porphyritic chondrules with phenocrysts of both olivine and pyroxene (POP chondrules) were not easily produced in the experiments. POP chondrules are common and it is important for deciphering their formation that we understand pyroxene nucleation properties of chondrule melts.

Lofgren, G. E.↗
NASA NTRS2004

An Evaluation of Quantitative Methods of Determining the Degree of Melting Experienced by a Chondrule

Many workers have considered the degree to which partial melting occurred in chondrules they have studied, and this has led to attempts to find reliable methods of determining the degree of melting. At least two quantitative methods have been used in the literature: a convolution index (CVI), which is a ratio of the perimeter of the chondrule as seen in thin section divided by the perimeter of a circle with the same area as the chondrule, and nominal grain size (NGS), which is the inverse square root of the number density of olivines and pyroxenes in a chondrule (again, as seen in thin section). We have evaluated both nominal grain size and convolution index as melting indicators. Nominal grain size was measured on the results of a set of dynamic crystallization experiments previously described, where aliquots of LEW97008(L3.4) were heated to peak temperatures of 1250, 1350, 1370, and 1450 C, representing varying degrees of partial melting of the starting material. Nominal grain size numbers should correlate with peak temperature (and therefore degree of partial melting) if it is a good melting indicator. The convolution index is not directly testable with these experiments because the experiments do not actually create chondrules (and therefore they have no outline on which to measure a CVI). Thus we had no means to directly test how well the CVI predicted different degrees of melting. Therefore, we discuss the use of the CVI measurement and support the discussion with X-ray Computed Tomography (CT) data.

Nettles, J. W.↗
NASA NTRS2004

Lunar and Planetary Science XXXV: The Future of Mars Surface Exploration

The session The Future of Mars Surface Exploration includes the following topics: 1) High Resolution Laser Scanning Techniques for Rock Abrasion and Texture Analyses on Mars and Earth; 2) Definitive Mineralogical Analysis of Mars Analog Rocks Using the CheMin XRD/XRF Instrument; 3) Quantitative Mineralogical Analysis of Mars Analogues Using CHEMIN Data and Rietveld Refinement; 4) In Situ Analytical Strategy for Mars Combining X-Ray and Optical Techniques; 5) In-Situ Dating on Mars: The Potential of OSL Dating; 6) Experiment of Dynamic Albedo of Neutrons (DAN): Searching for Water-rich Spots from the Rover on the Surface of Mars; and 7) Developing an Automated Science Analysis System for Mars Surface Exploration for MSL and Beyond.

Source record↗
NASA NTRS2012

Analysis of Dynamic Data from Supersonic Retropropulsion Experiments in NASA Langley's Unitary Plan Wind Tunnel

Recent experimental supersonic retropropulsion tests were conducted at the NASA Langley Research Center Unitary Plan Wind Tunnel Test Section 2 for a range of Mach numbers from 2.4 to 4.6. A 5-inch 70-degree sphere-cone forebody model with a 10-inch cylindrical aftbody experimental model was used which is capable of multiple retrorocket configurations. These configurations include a single central nozzle on the center point of the forebody, three nozzles at the forebody half-radius, and a combination of the first two configurations with no jets being plugged. A series of measurements were achieved through various instrumentation including forebody and aftbody pressure, internal pressures and temperatures, and high speed Schlieren visualization. Specifically, several high speed pressure transducers on the forebody and in the plenum were implemented to look at unsteady flow effects. The following work focuses on analyzing frequency traits due to the unsteady flow for a range of thrust coefficients for single, tri, and quad-nozzle test cases at freestream Mach 4.6 and angle of attack ranging from -8 degrees to +20 degrees. This analysis uses Matlab s fast Fourier transform, Welch's method (modified average of a periodogram), to create a power spectral density and analyze any high speed pressure transducer frequency traits due to the unsteady flow.

Codoni, Joshua R.↗
NASA NTRS2013

Using the Flow-3D General Moving Object Model to Simulate Coupled Liquid Slosh - Container Dynamics on the SPHERES Slosh Experiment: Aboard the International Space Station

The SPHERES Slosh Experiment (SSE) is a free floating experimental platform developed for the acquisition of long duration liquid slosh data aboard the International Space Station (ISS). The data sets collected will be used to benchmark numerical models to aid in the design of rocket and spacecraft propulsion systems. Utilizing two SPHERES Satellites, the experiment will be moved through different maneuvers designed to induce liquid slosh in the experiment's internal tank. The SSE has a total of twenty-four thrusters to move the experiment. In order to design slosh generating maneuvers, a parametric study with three maneuvers types was conducted using the General Moving Object (GMO) model in Flow-30. The three types of maneuvers are a translation maneuver, a rotation maneuver and a combined rotation translation maneuver. The effectiveness of each maneuver to generate slosh is determined by the deviation of the experiment's trajectory as compared to a dry mass trajectory. To fully capture the effect of liquid re-distribution on experiment trajectory, each thruster is modeled as an independent force point in the Flow-3D simulation. This is accomplished by modifying the total number of independent forces in the GMO model from the standard five to twenty-four. Results demonstrate that the most effective slosh generating maneuvers for all motions occurs when SSE thrusters are producing the highest changes in SSE acceleration. The results also demonstrate that several centimeters of trajectory deviation between the dry and slosh cases occur during the maneuvers; while these deviations seem small, they are measureable by SSE instrumentation.

Schulman, Richard↗
NASA NTRS2017

Practical Applications of Cables and Ropes in the ISS Countermeasures System

As spaceflight durations have increased over the last four decades, the effects of weightlessness on the human body are far better understood, as are the countermeasures. A combination of aerobic and resistive exercise devices contribute to countering the losses in muscle strength, aerobic fitness, and bone strength of today's astronauts and cosmonauts that occur during their missions on the International Space Station. Creation of these systems has been a dynamically educational experience for designers and engineers. The ropes and cables in particular have experienced a wide range of challenges, providing a full set of lessons learned that have already enabled improvements in on-orbit reliability by initiating system design improvements. This paper examines the on-orbit experience of ropes and cables in several exercise devices and discusses the lessons learned from these hardware items, with the goal of informing future system design.

Moore, Cherice↗
NASA NTRS2017

Effects of Adiabatic Heating on the High Strain Rate Deformation of Polymer Matrix Composites

Polymer matrix composites (PMCs) are increasingly being used in aerospace structures that are expected to experience complex dynamic loading conditions throughout their lifetime. As such, a detailed understanding of the high strain rate behavior of the constituents, particularly the strain rate, temperature, and pressure dependent polymer matrix, is paramount. In this paper, preliminary efforts in modeling experimentally observed temperature rises due to plastic deformation in PMCs subjected to dynamic loading are presented. To this end, an existing isothermal viscoplastic polymer constitutive formulation is extended to model adiabatic conditions by incorporating temperature dependent elastic properties and modifying the components of the inelastic strain rate tensor to explicitly depend on temperature. It is demonstrated that the modified polymer constitutive model is capable of capturing strain rate and temperature dependent yield as well as thermal softening associated with the conversion of plastic work to heat at high rates of strain. The modified constitutive model is then embedded within a strength of materials based micromechanics framework to investigate the manifestation of matrix thermal softening, due to the conversion of plastic work to heat, on the high strain rate response of a T700Epon 862 (T700E862) unidirectional composite. Adiabatic model predictions for high strain rate composite longitudinal tensile, transverse tensile, and in-plane shear loading are presented. Results show a substantial deviation from isothermal conditions; significant thermal softening is observed for matrix dominated deformation modes (transverse tension and in-plane shear), highlighting the importance of accounting for the conversion of plastic work to heat in the polymer matrix in the high strain rate analysis of PMC structures.

polymer matrix composites↗
NASA NTRS2018

Extraction of Doppler Observables from Open-Loop Recordings for the Juno Radio Science Investigation

The goal of the Juno Gravity Science investigation is to estimate the gravitational field of Jupiter by measurement of the spacecraft velocity during periods of closest approach. Velocity is measured by the Doppler shift of dual X- and Ka-band radio links between the Juno spacecraft, in orbit around Jupiter, and the DSS-25 antenna of the Deep Space Network (DSN). During times of closest-approach, Juno experiences large dynamic ranges caused by the orbital dynamics and spin signatures caused by the spin-stabilized spacecraft that are detectable by the receivers at DSS-25. Open-loop recordings of received voltages are processed to compute Doppler observables utilized in the estimation of the gravity field. Presented is a method to process open-loop data collected by the DSN to compensate for the spin signature of the spacecraft, removal of artifacts from Doppler observables caused by the high dynamic environment, and improve performance of the digital phase-locked loop utilized in the data processing.

Buccino, Dustin R.↗
NASA NTRSDate not supplied

Modal Correlation of Complex Aerospace Joints Using Automated Variable Substitution

A critical task involved with being able to predict flight loads accurately in aerospace finite element models (FEMs) is the prior verification of the FEMs by conducting modal survey testing (MST). Experience comparing dynamic response of initial FEMs to MST data tends to demonstrate that FEMs can have unacceptable accuracy even when best modeling practices are followed. One inherent source of inaccuracy in linear dynamic FEMs is the modeling of nonlinear joints with mechanisms such as spherical bearings. These joints are usually designed to freely translate or rotate under the high levels of loading experienced in flight. Engineers who create linear FEMs conventionally model these joints without any stiffness in the mechanism degrees of freedom to meet this design intent. However, inaccuracy is observed during test validation of these FEMs, which usually relies on low-level force excitation orders of magnitude below flight load levels. This low-level modal test rarely overcomes the joint friction that is present, and thus the mechanism joints are able to react loads. This divide between the test results and the FEM creates a significant challenge to the engineer who is performing the correlation, in that the engineer has no basis for what stiffness value should be used to make the FEM match the test results. A compounding challenge is that complicated built-up aerospace structures commonly have multiple joints through a load path where each joint will “stick” and “slip” at different levels of force input. Explicitly matching the dynamics of a system containing these nonlinear mechanisms would require a nonlinear FEM, which is prohibitively costly for dynamic simulations of most aerospace systems. The objective of this paper is to present a workflow that can efficiently cycle through many iterations of a FEM, allowing a Monte Carlo style examination of the design space to identify candidate stiffness values for nonlinear mechanism joints. The outlined approach is specific to MSC Nastran and utilizes MSC Nastran’s symbolic substitution capabilities, coupled with the IMAT™ and Attune™ software packages developed by ATA Engineering, Inc. (ATA). The workflow is demonstrated with a case study from the correlation effort for The Boeing Company’s Crew Space Transportation (CST)-100 Starliner FEM. Keywords: Correlation, MSC Nastran, IMAT™, Attune™, Finite Element Model, Modal Testing

Correlation↗
NASA NTRSDate not supplied

Validation of the Corcos Model for the Space Launch System using Unsteady Pressure Sensitive Paint

During atmospheric ascent launch vehicles (LVs) experience large dynamic loads at transonic conditions where aerodynamic buffet is most critical. To estimate buffet loads, coupled loads analyses typically utilize suitable forcing functions, called buffet forcing functions (BFFs). One of the key buffet environment contributors is the turbulent boundary layer (TBL) on the LV outer skin. The TBL-induced fluctuating pressures can be estimated using the widely-accepted Corcos model. In the context of transonic buffet, the performance of this model is not well established, partly because of lack of data. To fill this gap, NASA recently acquired extremely high-spatial-density data for the Space Launch System (SLS) vehicle, using the unsteady pressure sensitive paint (uPSP) optical measurement technique. A methodology is developed for validation of the Corcos model using these unique data, with a focus on the LV-design application. The model hypotheses are verified and the model parameters are empirically tuned. For selected panels on the vehicle, BFF coherence factors are derived based on the Corcos model and the associated panel BFFs are compared to uPSP data. It is shown that the modeled BFFs are in agreement with direct integration of uPSP data, except for regions where pressure fluctuations are spatially nonuniform. In those regions, the Corcos-based BFFs exhibit inherent limitations of BFF estimation methods that rely on discrete pressure measurements.

buffet↗
NASA NTRSDate not supplied

Validation of the Corcos Model for the Space Launch System using Unsteady Pressure Sensitive Paint

During atmospheric ascent launch vehicles (LVs) experience large dynamic loads at transonic conditions where aerodynamic buffet is most critical. To estimate buffet loads, coupled loads analyses typically utilize suitable forcing functions, called buffet forcing functions (BFFs). One of the key buffet environment contributors is the turbulent boundary layer (TBL) on the LV outer skin. The TBL-induced fluctuating pressures can be estimated using the widely-accepted Corcos model. In the context of transonic buffet, the performance of this model is not well established, partly because of lack of data. To fill this gap, NASA recently acquired extremely high-spatial-density data for the Space Launch System (SLS) vehicle, using the unsteady pressure sensitive paint (uPSP) optical measurement technique. A methodology is developed for validation of the Corcos model using these unique data, with a focus on the LV-design application. The model hypotheses are verified and the model parameters are empirically tuned. For selected panels on the vehicle, BFF coherence factors are derived based on the Corcos model and the associated panel BFFs are compared to uPSP data. It is shown that the modeled BFFs are in agreement with direct integration of uPSP data, except for regions where pressure fluctuations are spatially nonuniform. In those regions, the Corcos-based BFFs exhibit inherent limitations of BFF estimation methods that rely on discrete pressure measurements.

buffet↗
NASA NTRS2023

Space Launch System Unsteady Forces Developed from Unsteady-Pressure-Sensitive-Paint–Based Corcos Model Parameters

During atmospheric ascent, launch vehicles (LVs) experience large dynamic loads at transonic conditions where aerodynamic buffet is most critical. To estimate buffet loads, coupled loads analyses typically utilize suitable forcing functions, called buffet forcing functions (BFFs). One of the key buffet environment contributors is the turbulent boundary layer (TBL) on the LV outer skin. The TBL-induced fluctuating pressures can be estimated using the widely-accepted Corcos model. In the context of transonic buffet, the performance of this model is not well established, partly because of lack of data. To fill this gap, NASA recently acquired extremely high-spatial-density data for the Space Launch System (SLS) vehicle, using the unsteady pressure sensitive paint (uPSP) optical measurement technique. A methodology is developed for validation of the Corcos model using these unique data, with a focus on the LV-design application. The model hypotheses are verified and the model parameters are empirically tuned. For selected panels on the vehicle, BFF coherence factors are derived based on the Corcos model and the associated panel BFFs are compared to uPSP data. It is shown that the modeled BFFs are in agreement with direct integration of uPSP data, except for regions where pressure fluctuations are spatially nonuniform. In those regions, the Corcos-based BFFs exhibit inherent limitations of BFF estimation methods that rely on discrete pressure measurements.

buffet↗
NASA NTRSDate not supplied

Monodisperse Single-Material Granular Tribocharging Modeling and Experimental Validation

Charge transfer between insulating grains has been a topic of interest for many years as this phenomenon is extremely important to many areas in industry. Of particular interest to NASA is the behavior of electrically insulative dust grains such as those found on the lunar surface. Whether poured from a scoop during sample collection activities, agitated inside a drum via mining robots, or fluidized by a gas plume, particle-particle interactions between similar granular materials will be widespread on the Moon. Designers hope to have a predictive model for how dust grains are charged, transported, and deposited on flight systems to better understand issues electrostatics may cause in future missions. While difference in work function is often seen as a driver for charge transfer between two materials, this is an incomplete representation for insulative particles. Other asymmetries in the system can also lead to charge being transferred: one such being the difference between static vs dynamic particles. Experiments performed under vacuum in the Electrostatics and Surface Physics Laboratory (ESPL) clearly show that particles having more contacts with other particles tend to charge positively and particles having fewer contacts tend to charge negatively, despite being made from the same material. During these experiments, monodisperse (population of single diameter) spherical particles were held in a reservoir which was then elevated at one end to slope into a Faraday cup used to measure bulk charge of the grains. Care was taken to limit the number of spheres bouncing out of the cup, to isolate the beads from the container itself so that only grain-to-grain interactions occurred, and to assure neutrality of the beads before the experiment began. A discrete element method (DEM) modeling package already incorporating many granular mechanics interactions was augmented to include the electrostatic behaviors seen in experiments. The model can reproduce the experimental results above by tracking the number of contacts between pairs of individual grains and applying a charge transfer condition related to this contact parameter. The experimental results as well as their incorporation into the improved modeling suite will be discussed. Future work includes adding additional asymmetries into the experiments/model such as polydisperse populations of spherical particles and irregularly shaped grains.

granular↗
NASA NTRSDate not supplied

Monodisperse Single-Material Granular Tribocharging Modeling and Experimental Validation

Charge transfer between insulating grains has been a topic of interest for many years as this phenomenon is extremely important to many areas in industry. Of particular interest to NASA is the behavior of electrically insulative dust grains such as those found on the lunar surface. Whether poured from a scoop during sample collection activities, agitated inside a drum via mining robots, or fluidized by a gas plume, particle-particle interactions between similar granular materials will be widespread on the Moon. Designers hope to have a predictive model for how dust grains are charged, transported, and deposited on flight systems to better understand issues electrostatics may cause in future missions. While difference in work function is often seen as a driver for charge transfer between two materials, this is an incomplete representation for insulative particles. Other asymmetries in the system can also lead to charge being transferred: one such being the difference between static vs dynamic particles. Experiments performed under vacuum in the Electrostatics and Surface Physics Laboratory (ESPL) clearly show that particles having more contacts with other particles tend to charge positively and particles having fewer contacts tend to charge negatively, despite being made from the same material. During these experiments, monodisperse (population of single diameter) spherical particles were held in a reservoir which was then elevated at one end to slope into a Faraday cup used to measure bulk charge of the grains. Care was taken to limit the number of spheres bouncing out of the cup, to isolate the beads from the container itself so that only grain-to-grain interactions occurred, and to assure neutrality of the beads before the experiment began. A discrete element method (DEM) modeling package already incorporating many granular mechanics interactions was augmented to include the electrostatic behaviors seen in experiments. The model can reproduce the experimental results above by tracking the number of contacts between pairs of individual grains and applying a charge transfer condition related to this contact parameter. The experimental results as well as their incorporation into the improved modeling suite will be discussed. Future work includes adding additional asymmetries into the experiments/model such as polydisperse populations of spherical particles and irregularly shaped grains.

electrostatics↗