Search NASA⌕ Search

SEARCH · Search NASA

Results for “forward rate”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Experimental study of forward-located jet-interaction nozzles

The effects of forward-mounted sonic jet-interaction nozzles with one, three equal, or one large and two small orifices on the transitional or turbulent boundary-layer flow over a biconic (9-deg-25-arcmin/6-deg) model at angle of attack -10 to the 15 deg and Reynolds number 8.10 x 10 to the 6th/ft are investigated experimentally using pressure taps, force measurements, oil-flow visualization, and schlieren photography in the 20-in. Mach-6 wind tunel at NASA Langley. The injection flow rates are 0.055 and 0.026 lbm/s, with stagnation pressure 500 psia, stagnation temperature 1000 R, and dynamic pressure 8.7 psia. The results are presented in diagrams, graphs, and photographs and characterized. Moment amplification factors of 1.0 or better (maximum 1.8 at angle of attack 15 deg and flow rate 0.055 lbm/s) are observed for all nozzle types, but the configuration with three unequal orifices is found to give improvements of 10 percent over the single-orifice nozzle at a given flow rate.

Cavalleri, R. J.↗
NASA NTRS1989

A tone-aided dual vestigial sideband system for digital communications on fading channels

A spectrally efficient tone-aided dual vestigial sideband (TA/DVSB) system for digital data communications on fading channels is presented and described analytically. This PSK (phase-shift-keying) system incorporates a feed-forward, tone-aided demodulation technique to compensate for Doppler frequency shift and channel- induced, multipath fading. In contrast to other tone-in-band-type systems, receiver synchronization is derived from the complete data VSBs. Simulation results for the Rician fading channel are presented. These results demonstrate the receiver's ability to mitigate performance degradation due to fading and to obtain proper data carrier synchronization, suggesting that the proposed TA/DVSB system has promise for this application. Simulated BER (bit-error rate) data indicate that the TA/DVSB system effectively alleviates the channel distortions of the land mobile satellite application.

Hladik, Stephen M.↗
NASA NTRS2006

Crew Launch Vehicle (CLV) Upper Stage Configuration Selection Process

The Crew Launch Vehicle (CLV), a key component of NASA's blueprint for the next generation of spacecraft to take humans back to the moon, is being designed and built by engineers at NASA s Marshall Space Flight Center (MSFC). The vehicle s design is based on the results of NASA's 2005 Exploration Systems Architecture Study (ESAS), which called for development of a crew-launch system to reduce the gap between Shuttle retirement and Crew Exploration Vehicle (CEV) Initial Operating Capability, identification of key technologies required to enable and significantly enhance these reference exploration systems, and a reprioritization of near- and far-term technology investments. The Upper Stage Element (USE) of the CLV is a clean-sheet approach that is being designed and developed in-house, with element management at MSFC. The USE concept is a self-supporting cylindrical structure, approximately 115' long and 216" in diameter, consisting of the following subsystems: Primary Structures (LOX Tank, LH2 Tank, Intertank, Thrust Structure, Spacecraft Payload Adaptor, Interstage, Forward and Aft Skirts), Secondary Structures (Systems Tunnel), Avionics and Software, Main Propulsion System, Reaction Control System, Thrust Vector Control, Auxiliary Power Unit, and Hydraulic Systems. The ESAS originally recommended a CEV to be launched atop a four-segment Space Shuttle Main Engine (SSME) CLV, utilizing an RS-25 engine-powered upper stage. However, Agency decisions to utilize fewer CLV development steps to lunar missions, reduce the overall risk for the lunar program, and provide a more balanced engine production rate requirement prompted engineers to switch to a five-segment design with a single Saturn-derived J-2X engine. This approach provides for single upper stage engine development for the CLV and an Earth Departure Stage, single Reusable Solid Rocket Booster (RSRB) development for the CLV and a Cargo Launch Vehicle, and single core SSME development. While the RSRB design has changed since the CLV Project's inception, the USE design has remained essentially a clean-sheet approach. Although a clean-sheet upper stage design inherently carries more risk than a modified design, it does offer many advantages: a design for increased reliability; built-in extensibility to allow for commonality/growth without major redesign; and incorporation of state-of-the-art materials, hardware, and design, fabrication, and test techniques and processes to facilitate a potentially better, more reliable system. Because consideration was given in the ESAS to both clean-sheet and modified USE designs, this paper will highlight the advantages and disadvantages of both approaches and provide a detailed discussion of trades/selections made that led to the final upper stage configuration.

Davis, Daniel J.↗
NASA NTRSDate not supplied

Scaling of Liquefaction Systems and the Effects of Gravity

Recent exploration initiatives both by NASA and others have produced interest in the liquefaction of fluids produced through in-situ processes on the surfaces of the Moon and Mars. Liquefaction of fluids in cryogenic temperatures is routinely done at large scale for terrestrial uses, but these processes do not necessarily scale down in an economical or technologically feasible manner for the anticipated rates of initial Lunar or Martian production plants. To understand appropriate processes and scaling parameters, various options should be considered. A multi-center team at NASA considered multiple different refrigeration cycles and refrigeration integration methodologies as well as how these might fit into early liquefaction plants. These studies resulted in the conclusion that integrating the tubing on the storage tank wall (for both structural and heat spreading reasons), preferably the tank which will actually use the fluid, is the nearest path forward. Given that assumption on the general framework of the liquefaction system, there are several different heat transfer mechanisms to consider from a scaling perspective. These include forced convection heat removal to the refrigeration system (or cryocooler), conduction through the tank wall heat exchanger, and condensation (with some natural convection) on the inner tank wall. Analysis of these mechanisms shows that while there is some sensitivity to gravitational level, that within the bounds of current interest (Lunar and Martian applications), this sensitivity does not dominate the liquefaction application. While there will be some effect, perhaps in a limiting manner as the tanks approach some high fill level, system level testing on the Earth should suffice for the performance prediction and demonstration of liquefaction operations as applicable to Lunar and Martian applications. However, as one approaches orbital conditions, this general approach to liquefaction will not be appropriate as the scaling of the heat transfer mechanisms is not appropriate. At this point, other approaches will need to be developed and demonstrated in the micro-gravity environment.

Cryogenics↗
NASA NTRS2023

Flexible User Radio for Lunar Missions

NASA’s Artemis program and other lunar exploration and development programs are planning over 40 lunar missions before 2030. Lunar missions, both crewed and uncrewed, include orbiters, landers, rovers, and surface stations. All these missions require communications with Earth, either via Direct to Earth (DTE) links or through relays in lunar orbit. Multiple DTE options are available among existing and planned ground stations: Deep Space Network (DSN), European Space Agency, and others. Relay options include the planned Lunar Gateway, LunaNet compliant relays, and some lunar landers propose to launch dedicated orbiters. The dilemma for lunar system designers is to identify a communication link which meets mission requirements but does not have issues of limited access (e.g. DSN is in high demand supporting deep space missions with high priority and some with inflexible schedules), system impacts (high power Radio Frequency (RF) for DTE links), cost (dedicated relay), or operational date. To avoid this difficult decision, a Flexible Radio for Lunar Missions is proposed, which will enable system designs to proceed prior to any final decision on the communication network to be used, by enabling compatibility with any of multiple DTE or orbital relay communication systems. The Flexible Radio will support the necessary frequency, bandwidth, modulation, and power requirements to interoperate with the majority of known or planned DTE or relay systems, and can be designed into a lunar mission without prior knowledge of which link will ultimately be used. Furthermore, the link being used can be changed as needed during the mission, in near real time. The Flexible Radio design will leverage work already completed at NASA in the areas of Wideband RF, Software Defined Radio, Adaptive Coding and Modulation, and Phased Array antennas. The Flexible Radio requires sufficient bandwidth to cover the allocated frequencies for both the operation of links in cislunar space and for space-to-Earth links; the flexibility to support multiple modulations, data rates, and coding schemes; the ability to identify available relays, detect and recognize the signals of those relays, and adapt its own frequency, modulation, symbol rate, and code rate to operate with the detected relay (or DTE station); and finally, it requires appropriate software to support network configuration and interoperability with the detected network. The Flexible Radio can be designed in a sufficiently small, lightweight, and low-power package to be used in a wide variety of lunar systems. The initial implementation, as proposed, will focus on the Ka-band, supporting up to 2 GHz bandwidth around the 27 GHz frequency for return links, and 23 GHz for forward links. Other frequency bands are under consideration for future configurations. The software defined modem will support OQPSK, BPSK, and NASA-defined modulations which also support two-way ranging with data. For near-real time adaptation, the Flexible Radio will scan the sky for available relays, using a phased array antenna with Adaptive/Cognitive Communications. It will then configure for network interoperability supporting DTN and other protocol options. The Flexible Radio will support scheduled connections and on-demand use when available.

Lunar Space Communications↗
NASA NTRSDate not supplied

Flexible User Radio for Lunar Missions

NASA’s Artemis program and other lunar exploration and development programs are planning over 40 lunar missions before 2030. Lunar missions, both crewed and uncrewed, include orbiters, landers, rovers, and surface stations. All these missions require communications with Earth, either via Direct to Earth (DTE) links or through relays in lunar orbit. Multiple DTE options are available among existing and planned ground stations: Deep Space Network (DSN), European Space Agency, and others. Relay options include the planned Lunar Gateway, LunaNet compliant relays, and some lunar landers propose to launch dedicated orbiters. The dilemma for lunar system designers is to identify a communication link which meets mission requirements but does not have issues of limited access (e.g. DSN is in high demand supporting deep space missions with high priority and some with inflexible schedules), system impacts (high power Radio Frequency (RF) for DTE links), cost (dedicated relay), or operational date. To avoid this difficult decision, a Flexible Radio for Lunar Missions is proposed, which will enable system designs to proceed prior to any final decision on the communication network to be used, by enabling compatibility with any of multiple DTE or orbital relay communication systems. The Flexible Radio will support the necessary frequency, bandwidth, modulation, and power requirements to interoperate with the majority of known or planned DTE or relay systems, and can be designed into a lunar mission without prior knowledge of which link will ultimately be used. Furthermore, the link being used can be changed as needed during the mission, in near real time. The Flexible Radio design will leverage work already completed at NASA in the areas of Wideband RF, Software Defined Radio, Adaptive Coding and Modulation, and Phased Array antennas. The Flexible Radio requires sufficient bandwidth to cover the allocated frequencies for both the operation of links in cislunar space and for space-to-Earth links; the flexibility to support multiple modulations, data rates, and coding schemes; the ability to identify available relays, detect and recognize the signals of those relays, and adapt its own frequency, modulation, symbol rate, and code rate to operate with the detected relay (or DTE station); and finally, it requires appropriate software to support network configuration and interoperability with the detected network. The Flexible Radio can be designed in a sufficiently small, lightweight, and low-power package to be used in a wide variety of lunar systems. The initial implementation, as proposed, will focus on the Ka-band, supporting up to 2 GHz bandwidth around the 27 GHz frequency for return links, and 23 GHz for forward links. Other frequency bands are under consideration for future configurations. The software defined modem will support OQPSK, BPSK, and NASA-defined modulations which also support two-way ranging with data. For near-real time adaptation, the Flexible Radio will scan the sky for available relays, using a phased array antenna with Adaptive/Cognitive Communications. It will then configure for network interoperability supporting DTN and other protocol options. The Flexible Radio will support scheduled connections and on-demand use when available.

Lunar Space Communications↗
DOE OSTI2025

Observation and Simulation of Methane Plumes During the Morning Boundary Layer Transition

Abstract Methane (CH 4 ) contributes significantly to global warming. However, accurate identification of CH 4 sources for reducing CH 4 emissions is often hampered by inadequate accuracy and spatiotemporal coverage of CH 4 detection, and lack of accurate CH 4 forward modeling used in top‐down inversion systems. In this study, a field experiment was conducted in Pampa, Texas using two CH 4 sensors (LI‐COR and OGI camera) to detect CH 4 releases. We investigated whether high‐resolution simulations using the Weather Research and Forecasting (WRF) model with greenhouse gases (WRF‐GHG) could accurately simulate the CH 4 plumes in the presence of evolving atmospheric boundary layer from sunrise to noon. CH 4 plumes showed substantial variation in time. At a release rate of ∼17.5 kg hr −1 , the maximum enhancement of CH 4 measured by LI‐COR was 2.6 ppm at sunrise (7:36 a.m.), 250 m from the release location. Within half an hour after sunrise, this enhancement decreased to 0.3–0.4 ppm. The enhancement was 0.2 ppm by 10:00 a.m. and further dropped to less than 0.1 ppm after 11:30 a.m. Due to the low temperature at sunrise, the OGI camera failed to detect the CH 4 plume. The WRF‐GHG large‐eddy simulation (LES) with 32 m grid spacing successfully reproduced these CH 4 enhancements. In situ measurements together with numerical simulations illustrate the impact of the transition from a stable boundary layer in the early morning to a convective boundary layer at noon on the dispersion of CH 4 plumes. Additionally, CH 4 plumes from a cattle farm in Oklahoma are briefly examined using the same modeling approach.

Hu, Xiao‐Ming [Center for Analysis and Prediction ↗
NASA NTRS1986

An analysis of bi-directional use of frequencies for satellite communications

The bi-directional use of frequencies allocated for space communications has the potential to double the orbit/spectrum capacity available. The technical feasibility of reverse band use (RBU) at C-band (4 GHz uplinks and 6 GHz downlinks) is studied. The analysis identifies the constraints under which both forward and reverse band use satellite systems can share the same frequencies with terrestrial, line of sight transmission systems. The results of the analysis show that RBU satellite systems can be similarly sized to forward band use (FBU) satellite systems. In addition, the orbital separation requirements between RBU and FBU satellite systems are examined. The analysis shows that a carrier to interference ratio of 45 dB can be maintianed between RBU and FBU satellites separated by less than 0.5 deg., and that a carrier to interference ratio of 42 dB can be maintained in the antipodal case. Rain scatter propagation analysis shows that RBU and FBU Earth stations require separation distances fo less than 10 km at a rain rate of 13.5 mm/hr escalating to less than 100 km at a rain rate of 178 mm/hr for Earth station antennas in the 3 to 10 m range.

Whyte, W. A., Jr.↗
NASA NTRS1986

An analysis of bidirectional use of frequencies for satellite communications

The bi-directional use of frequencies allocated for space communications has the potential to double the orbit/spectrum capacity available. The technical feasibility of reverse band use (RBU) at C-band (4 GHz uplinks and 6 GHz downlinks) is studied. The analysis identifies the constraints under which both forward and reverse band use satellite systems can share the same frequencies with terrestrial, line of sight transmission systems. The results of the analysis show that RBU satellite systems can be similarly sized to forward band use (FBU) satellite systems. In addition, the orbital separation requirements between RBU and FBU satellite systems are examined. The analysis shows that a carrier to interference ratio of 45 dB can be maintained between RBU and FBU satellites separated by less than 0.5 deg., and that a carrier to interference ratio of 42 dB can be maintained in the antipodal case. Rain scatter propagation analysis shows that RBU and FBU earth stations require separation distances of less than 10 km at a rain rate of 13.5 mm/hr escalating to less than 100 km at a rain rate of 178 mm/hr for earth station antennas in the 3 to 10 m range.

Whyte, W. A., Jr.↗
NASA NTRS1986

Flight evaluation of a precision landing task for a powered-lift STOL aircraft

A flight research experiment was conducted with the NASA-Ames Research Center's Quiet Short-Haul Research Aircraft to determine the factors which influence the touchdown distribution for a powered-lift STOL aircraft. The pilots were given two tasks for each of a series of precision approaches flown using a microwave landing system (MLS) in simulated instrument meteorological conditions. They flew the aircraft, with forward vision obscured by a screen, to a 100-ft decision height using a flightpath-oriented, color electronic display and one of four levels of control augmentation. Approaches were flown along a nominal 6 deg glidepath, as well as to calibrated offsets at the decision height to establish a variety of initial conditions for the landing task. The screen was removed at the decision height and the pilot was briefed to land in a 200 foot touchdown zone of the STOLport with a sink rate less than 5 ft/sec. Statistical performance envelopes and pilot ratings are used to describe the results of this experiment. The data generated are expected to be useful for establishing STOL aircraft operating requirements and STOL MLS approach criteria.

Watson, D. M.↗
NASA NTRS1986

An analysis of bi-directional use of frequencies for satellite communications

The bi-directional use of frequencies allocated for space communications has the potential to double the orbit/spectrum capacity available. The technical feasibility of reverse band use (RBU) at C-band (4 GHz uplinks and 6 GHz downlinks) is studied. The analysis identifies the constraints under which both forward and reverse band use satellite systems can share the same frequencies with terrestrial, line of sight transmission systems. The results of the analysis show that RBU satellite systems can be similarly sized to forward band use (FBU) satellite systems. In addition, the orbital separation requirements between RBU and FBU satellite systems are examined. The analysis shows that a carrier to interference ratio of 45 dB can be maintained between RBU and FBU satellites separated by less than 0.5 deg, and that A carrier to interference ratio of 42 dB can be maintained in the antipodal case. Rain scatter propagation analysis shows that RBU and FBU earth stations require separation distances of less than 10 km at a rain rate of 13.5 mm/hr escalating to less than 100 km at a rain rate of 178 mm/hr for earth station antennas in the 3 to 10 m range.

Whyte, W. A., Jr.↗
NASA NTRS1994

Regular Topologies for Gigabit Wide-Area Networks

In general terms, this project aimed at the analysis and design of techniques for very high-speed networking. The formal objectives of the project were to: (1) Identify switch and network technologies for wide-area networks that interconnect a large number of users and can provide individual data paths at gigabit/s rates; (2) Quantitatively evaluate and compare existing and proposed architectures and protocols, identify their strength and growth potentials, and ascertain the compatibility of competing technologies; and (3) Propose new approaches to existing architectures and protocols, and identify opportunities for research to overcome deficiencies and enhance performance. The project was organized into two parts: 1. The design, analysis, and specification of techniques and protocols for very-high-speed network environments. In this part, SRI has focused on several key high-speed networking areas, including Forward Error Control (FEC) for high-speed networks in which data distortion is the result of packet loss, and the distribution of broadband, real-time traffic in multiple user sessions. 2. Congestion Avoidance Testbed Experiment (CATE). This part of the project was done within the framework of the DARTnet experimental T1 national network. The aim of the work was to advance the state of the art in benchmarking DARTnet's performance and traffic control by developing support tools for network experimentation, by designing benchmarks that allow various algorithms to be meaningfully compared, and by investigating new queueing techniques that better satisfy the needs of best-effort and reserved-resource traffic. This document is the final technical report describing the results obtained by SRI under this project. The report consists of three volumes: Volume 1 contains a technical description of the network techniques developed by SRI in the areas of FEC and multicast of real-time traffic. Volume 2 describes the work performed under CATE. Volume 3 contains the source code of all software developed under CATE.

Shacham, Nachum↗
NASA NTRSDate not supplied

Composites From in-Situ Consolidation Automated Fiber Placement of Thermoplastics for High-Rate Aircraft Manufacturing

The National Aeronautics and Space Administration (NASA) project Hi-Rate Composites Aircraft Manufacturing (HiCAM) aims to significantly increase commercial aircraft composite structures manufacturing rate. Thermoplastic composites offer attractive solutions to rapid manufacturing due to their ability to be formed and consolidated quickly. NASA has a particular interest in assessing composite structure manufacturing utilizing an in-situ consolidation automated fiber placement (AFP) of thermoplastics (ICAT) process employing current state-of-the-art laser heating systems. Three semi-crystalline polyaryletherketone (PAEK) thermoplastic tape materials were characterized to ascertain the ICAT process parameters. The required laser power settings were determined at Electroimpact, Inc., measuring material temperatures utilizing a forward looking infrared (FLIR) thermal imaging camera and thermocouples. The material temperature, tool temperature, and placement speed were varied for resulting consolidation quality assessment. The resulting temperature data were also utilized to calibrate thermal analysis models under development at NASA. The experimental temperature data confirmed analytical results. The quality of the resulting test panels was evaluated by both non-destructive evaluation as well as destructively by photo-microscopy. The effect on interlaminar strength was determined by short beam strength testing. Test results of carbon fiber laminates fabricated by ICAT using polyetheretherketone (PEEK), polyetherketoneketone (PEKK), and low-melt polyaryletherketone (LM-PAEK) at various placement temperatures and placement speeds are presented.

thermoplastic composites↗
DOE OSTI2020

SQUARE: Strategic Quantum Ancilla Reuse for Modular Quantum Programs via Cost-Effective Uncomputation

Compiling high-level quantum programs to machines that are size constrained (i.e. limited number of quantum bits) and time constrained (i.e. limited number of quantum operations) is challenging. In this paper, we present SQUARE (Strategic QUantum Ancilla REuse), a compilation infrastructure that tackles allocation and reclamation of scratch qubits (called ancilla) in modular quantum programs. At its core, SQUARE strategically performs uncomputation to create opportunities for qubit reuse. Current Noisy Intermediate-Scale Quantum (NISQ) computers and forward-looking Fault-Tolerant (FT) quantum computers have fundamentally different constraints such as data locality, instruction parallelism, and communication overhead. Our heuristic-based ancilla-reuse algorithm balances these considerations and fits computations into resource-constrained NISQ or FT quantum machines, throttling parallelism when necessary. To precisely capture the workload of a program, we propose an improved metric, the "active quantum volume," and use this metric to evaluate the effectiveness of our algorithm. Furthermore, our results show that SQUARE improves the average success rate of NISQ applications by 1.47X. Surprisingly, the additional gates for uncomputation create ancilla with better locality, and result in substantially fewer swap gates and less gate noise overall. SQUARE also achieves an average reduction of 1.5X (and up to 9.6X) in active quantum volume for FT machines.

compiler optimization↗
NASA NTRS1992

Passive microwave precipitation mapping and retrieval simulation

A numerical simulation of the satellite-based multispectral passive microwave mapping and precipitation retrieval process is described. The simulation contains three major components: (1) the forward radiative transfer calculation; (2) the sensor observation simulation; and (3) the precipitation retrieval algorithm. Secondary components include a Karhunen-Loeve transformation module and antenna pattern deconvolution module. The simulation facilitates the investigation of candidate precipitation retrieval algorithms using sub-Nyquist brightness temperature imagery, and the comparison of the relative merits of proposed radiometric systems such as the EOS multispectral imaging microwave radiometer (MIMR), the tropical rainfall measurement mission (TRMM) microwave imager (TRMM TMI), and the geosynchronous satellite sensors. A procedure for retrieving rain rates using a statistical iterative approach is outlined.

Skofronick, G. M.↗
NASA NTRS2011

Feasibility of Ultraviolet Light Emitting Diodes as an Alternative Light Source for Photocatalysis

The objective of this study was to determine whether ultraviolet light emitting diodes (UV-LEDs) could serve as an alternative photon source efficiently for heterogeneous photocatalytic oxidation (PCO). An LED module consisting of 12 high-power UV-A LEDs was designed to be interchangeable with a UV-A fluorescent black light blue (BLB) lamp in a Silica-Titania Composite (STC) packed bed annular reactor. Lighting and thermal properties were characterized to assess the uniformity and total irradiant output. A forward current of (I(sub F)) 100 mA delivered an average irradiance of 4.0 m W cm(exp -2), which is equivalent to the maximum output of the BLB, but the irradiance of the LED module was less uniform than that of the BLB. The LED- and BLB-reactors were tested for the oxidization of 50 ppmv ethanol in a continuous flow-through mode with 0.94 sec space time. At the same irradiance, the UV-A LED reactor resulted in a lower PCO rate constant than the UV-A BLB reactor (19.8 vs. 28.6 nM CO2 sec-I), and consequently lower ethanol removal (80% vs. 91%) and mineralization efficiency (28% vs. 44%). Ethanol mineralization increased in direct proportion to the irradiance at the catalyst surface. This result suggests that reduced ethanol mineralization in the LED- reactor could be traced to uneven irradiance over the photocatalyst, leaving a portion of the catalyst was under-irradiated. The potential of UV-A LEDs may be fully realized by optimizing the light distribution over the catalyst and utilizing their instantaneous "on" and "off' feature for periodic irradiation. Nevertheless, the current UV-A LED module had the same wall plug efficiency (WPE) of 13% as that of the UV-A BLB. These results demonstrated that UV-A LEDs are a viable photon source both in terms of WPE and PCO efficiency.

Levine, Langanf H.↗
NASA NTRSDate not supplied

Stability Analysis of the Flow Over a Swept Forward-Facing Step Using PIV Base Flows

Step excrescences are a type of surface imperfection encountered on swept wings of commercial aircraft, commonly because accessibility requirements prevent creating the wing’s surface from a single panel. If the step height is too large, super-critical, the flow can undergo an early transition to turbulence, which can be highly detrimental for the performance of the wing. In the case of a forward-facing step on a swept wing in a low-disturbance environment, stationary crossflow vortices can develop a significant amplitude upstream of the step and hence dominate the structure of the boundary-layer flow over the step. The main goal of the present investigation is to illuminate the path to transition supported by the fascinatingly complex flow field in the direct downstream vicinity of a step with a super critical height. The high-resolution, stereographic Particle Image Velocimetry (PIV) measurement dataset presently available for this flow field provides a complete description of the laminar flow for the execution of BiGlobal stability analysis in a plane parallel to the step. Although the notorious sensitivity of stability results to the description of the base flow demands a very careful uncertainty analysis of those results, it is argued that this very fact can be leveraged to produce new insight into the supported perturbation dynamics. In performing the analysis, several unsteady mode families are discovered that display the explosive perturbation expected for early transition to be induced. In considering domain widths equal to an integer-multiple of the incident crossflow-vortex wavelength and analyzing an extent of 5 crossflow-vortex wavelengths parallel to the step, it is found that the stability results converge while increasing the domain width. It is demonstrated, moreover, that the results for the wider domains can be approximated by appropriately averaging the results on neighboring single-crossflow-vortex-wavelength domains covering the same region. Besides being useful for computational purposes, this observed property suggests interpreting the instability mechanism as a distorted primary mechanism rather than a “proper” secondary mechanism. This follows in the context of the secondary in-stability analysis of three-dimensional boundary layers, because the secondary mechanism is usually characterized by being localized in a pocket of strong shear, while the distorted primary mechanism typically has an infinite support in the direction parallel to the step. Even though the growth rates are found to be sensitive to the interrogation-window size inherent to the PIV post-processing procedure, the spatial structure of the eigenfunctions is found to be relatively insensitive. Lastly, the spatial structure of the eigenfunctions corresponding to all velocity components are matched with the shape functions determined by computing the Spectral Proper Orthogonal Decomposition (SPOD) of a time-resolved measurement of the perturbation content.

forward-facing step↗
NASA NTRS2003

ASF3

This reporting period marked a change in the funding configuration from a combination of a grant and a contract from two different National Aeronautics and Space Administration (NASA) sections to one single contract. One year of this reporting was under the grant/kontract configuration with the changeover occurring on 1 April 2003. Much of the work duties remained the same with some exception, notably the removal of the RADARSAT Geophysical Processor System and the removal of the commercialization line item from the contract. We chose this reporting period as a transition from the previous reporting period of 1 April to 31 March, to the current reporting period of 18 November to 17 November. The Alaska Synthetic Aperture Facility s (ASF) mission has been updated to carry us forward into the future congruent with our changed relationship with NASA. ASF will continue to evolve, and NASA will remain our primary customer. To compliment our new mission, we have a new name, the Alaska Satellite Facility (ASF), deeply rooted in the University environment and focused on satellite data products, services, and science support. We have the opportunity to reshape and rebuild ASF; we will continue to honor our heritage and Serve the science community. Our long-term goals include the commitment to continued first-rate service to our user community. This report contains input from ASF as a whole on the three major components of the NASA Contract, namely tasks devoted to the Distributed Active Archive Center (DAAC), the Receiving Ground Station (RGS), and the National Oceanics and Atmospherics Administration (NOAA).

LaBelle-Hamer, Nettie↗