Search NASA⌕ Search

SEARCH · Search NASA

Results for “generalized predictive control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42

Chemistry of K in Cu(In,Ga)Se 2 photovoltaic absorbers: Effects of temperature on Cu-K-In-Se films

Incorporation of K has led to world record Cu(In,Ga)Se 2 photovoltaic power conversion efficiencies, but there is poor consensus about the role of phase impurities in these advances. This work lays a foundation for identifying and controlling these phase impurities. Films of Cu-K-In-Se were co-evaporated at varied K/(K + Cu) compositions and substrate temperatures (with constant (K + Cu)/In ~ 0.85). Increased Na composition on the substrate's surface and decreased growth temperature were both found to favor Cu 1-x K x InSe 2 alloy formation, relative to two-phase CuInSe 2 +KInSe 2 formation. Structures from X-ray diffraction (XRD), band gaps, resistivities, minority carrier lifetimes and carrier concentrations from time-resolved photoluminescence were in agreement with previous reports, where low K/(K + Cu) composition films exhibited properties promising for photovoltaic absorbers. Films grown at 400-500 °C were then annealed to 600 degrees C in a controlled Se ambient, which caused K loss by evaporation in proportion to the initial K/(K + Cu) composition. Similar to growth temperature, annealing drove Cu 1-x K x InSe 2 alloy consumption and CuInSe 2 +KInSe 2 production, as evidenced by high temperature XRD. Annealing also decomposed KInSe 2 and formed K 2 In 12 Se 19 . At high temperature, the KInSe 2 crystal lattice gradually contracted as temperature and time increased, as well as just time. Evaporative loss of K during annealing could accompany the generation of vacancies on K lattice sites, and may explain the KInSe 2 lattice contraction. As a result, this knowledge of Cu-K-In-Se material chemistry may be used to predict and control minor phase impurities in Cu(In,Ga)(Se,S) 2 photovoltaic absorbers - where impurities below typical detection limits may have played a role in recent world record photovoltaic efficiencies that utilized KF post-deposition treatments.

14 SOLAR ENERGY↗

First-principles many-body theory for ultra-cold atoms

Recent breakthroughs in the creation of ultra-cold atoms in the laboratory have ushered in unprecedented changes in physical science. These enormous changes in the coldest temperatures available in the laboratory mean that many novel experiments are possible. There is unprecedented control and simplicity in these novel systems, meaning that quantum many-body theory is now facing severe challenges in quantitatively understanding these new results. We discuss some of the new experiments and recently developed theoretical techniques required to predict the results obtained.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Elasticity dominates strength and failure in metallic glasses

Two distinct deformation mechanisms of shearing and volume dilatation are quantitatively analyzed in metallic glasses (MGs) from the fundamental thermodynamics. Their competition is deduced to intrinsically dominate the strength and failure behaviors of MGs. Both the intrinsic shear and normal strengths give rise to the critical mechanical energies to activate destabilization of amorphous structures, under pure shearing and volume dilatation, respectively, and can be determined in terms of elastic constants. By adopting an ellipse failure criterion, the strength and failure behaviors of MGs can be precisely described just according to their shear modulus and Poisson's ratio without mechanical testing. Quantitative relations are established systematically and verified by experimental results. Accordingly, the real-sense non-destructive failure prediction can be achieved in various MGs. By highlighting the broad key significance of elasticity, a “composition-elasticity-property” scheme is further outlined for better understanding and controlling the mechanical properties of MGs and other glassy materials from the elastic perspectives.

42 ENGINEERING↗

Thermodynamic properties and solidification kinetics of intermetallic Ni{sub 7}Zr{sub 2} alloy investigated by electrostatic levitation technique and theoretical calculations

The thermodynamic properties, including the density, volume expansion coefficient, ratio of specific heat to emissivity of intermetallic Ni{sub 7}Zr{sub 2} alloy, have been measured using the non-contact electrostatic levitation technique. These properties vary linearly with temperature at solid and liquid states, even down to the obtained maximum undercooling of 317 K. The enthalpy, glass transition, diffusion coefficient, shear viscosity, and surface tension were obtained by using molecular dynamics simulations. Ni{sub 7}Zr{sub 2} has a relatively poor glass forming ability, and the glass transition temperature is determined as 1026 K. The inter-diffusivity of Ni{sub 7}Zr{sub 2} alloy fitted by Vogel–Fulcher–Tammann law yields a fragility parameter of 8.49, which indicates the fragile nature of this alloy. Due to the competition of increased thermodynamic driving force and decreased atomic diffusion, the dendrite growth velocity of Ni{sub 7}Zr{sub 2} compound exhibits double-exponential relationship to the undercooling. The maximum growth velocity is predicted to be 0.45 m s{sup −1} at the undercooling of 335 K. Theoretical analysis reveals that the dendrite growth is a diffusion-controlled process and the atomic diffusion speed is only 2.0 m s{sup −1}.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Electron interference in atomic ionization by two crossing polarized ultrashort pulses

Formation of geometrically regular interference patterns in the photoelectron momentum distributions (PMDs) corresponding to the photoionization of atoms by two single-color, crossing ultrashort pulses is investigated both analytically and numerically. It is shown that, in contrast to the photoionization by monochromatic pulses, PMDs for the ionization by crossing and co-propagating broadband pulses are essentially different (unless both pulses are linearly polarized), namely, when one pulse is linearly polarized along the propagation direction, ˆk, of the circularly polarized (CP) pulse, then interference maxima (minima) of the ionization probability have the form of three-dimensional single-arm regular spirals which are wound along ˆk. Next, the interference maxima (minima) of the ionization probability by a pair of crossing elliptically polarized pulses have the form of either Newton's rings or two-arm Fermat's spirals, depending on the position of a detection plane. Remarkably, these regular patterns occur only for certain values of the pulse ellipticities, and they become distorted for CP pulses. For both above-mentioned pulse configurations, the features of interference patterns depend on the time delay between pulses, their relative electric field amplitude, and relative carrier-envelope phase. Our predictions, illustrated by the numerical results for the ionization of H and He atoms by two orthogonal pulses, are quite general and we expect them to be valid for the ionization of any randomly oriented atomic or molecular target.

74 ATOMIC AND MOLECULAR PHYSICS↗

Testing quantum gravity using pulsed optomechanical systems

An interesting idea, dating back to Feynman [Report from Chapel Hill Conference, edited by C. M. DeWitt and D. Rickles (1957)], argues that quantum mechanics may break down for large masses if one entertains the possibility that gravity can be “classical,” thereby leading to predictions different from conventional low-energy quantum gravity. Despite the technical difficulty in testing such deviations, a large number of experimental proposals have been put forward due to the high level of fundamental interest. Here, we consider the Schrödinger-Newton (SN) theory and the correlated worldline (CWL) theory, and show that they can be distinguished from conventional quantum mechanics, as well as each other, by performing pulsed optomechanics experiments. For CWL specifically we develop a framework resembling the commonly used “Heisenberg-picture” treatment of coupled oscillators, allowing one to perform simple calculations for such systems without delving into the deeper path-integral formalism. We find that discriminating between the theories will be very difficult until experimental control over low frequency quantum optomechanical systems is pushed much further. Furthermore, the predicted departures of SN and CWL from quantum mechanics occur at the same scale, so both alternative models could in principle be probed by a single experiment.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Q-FANSTM for general aviation aircraft

Continued growth of general aviation over the next 10 to 15 years is dependent on continuing improvement in aircraft safety, utility, performance and cost. Moreover, these advanced aircraft will need to conform to expected government regulations controlling propulsion system emissions and noise levels. An attractive compact low noise propulsor concept, the Q-FANTM when matched to piston, rotary combustion, or gas turbine engines opens up the exciting prospect of new, cleaner airframe designs for the next generation of general aviation aircraft which will provide these improvements and meet the expected noise and pollution restriction of the 1980 time period. New Q-FAN methodology which was derived to predict Q-FAN noise, weight and cost is presented. Based on this methodology Q-FAN propulsion system performance, weight, noise, and cost trends are discussed. Then the impact of this propulsion system type on the complete aircraft is investigated for several representative aircraft size categories. Finally, example conceptual designs for Q-FAN/engine integration and aircraft installations are presented.

Worobel, R.↗

Prediction, evaluation, and specification of flying qualities by means of step target tracking

A new approach to flying qualities specification and evaluation is presented which coordinates current research in the areas of pilot ratings, pilot-aircraft modeling techniques, and simulation and flight test procedures. A time-domain pilot model is described which can model discontinuous and nonlinear pilot behavior in conjunction with completely general time-varying nonlinear aircraft models to simulate discrete maneuvers. This pilot-aircraft model is applied to an existing set of in-flight simulation data, and calculates tracking error and time-on-target statistics for step target tracking that directly relate to the reported pilot comments and ratings. Predicted step target tracking data for eighteen F-5E flight conditions are presented, and the use of the method for control system design is demonstrated using the YF-17.

Onstott, E. D.↗

Full scale wind tunnel investigation of a bearingless main helicopter rotor

A stability test program was conducted to determine the effects of airspeed, collective pitch, rotor speed and shaft angle on stability and loads at speeds beyond that attained in the BMR/BO-105 flight test program. Loads and performance data were gathered at forward speeds up to 165 knots. The effect of cyclic pitch perturbations on rotor response was investigated at simulated level flight conditions. Two configuration variations were tested for their effect on stability. One variable was the control system stiffness. An axially softer pitch link was installed in place of the standard BO-105 pitch link. The second variation was the addition of elastomeric damper strips to increase the structural damping. The BMR was stable at all conditions tested. At fixed collective pitch, shaft angle and rotor speed, damping generally increased between hover and 60 knots, remained relatively constant from 60 to 90 knots, then decreased above 90 knots. Analytical predictions are in good agreement with test data up to 90 knots, but the trend of decreasing damping above 90 knots is contrary to the theory.

Source record↗

Control of volume resistivity in inorganic-organic separators

Control of resistivity in NASA inorganic-organic separators is achieved by incorporating small percentages of high surface area, fine-particle silica with other ingredients in the separator coating. The volume resistivity appears to be predictable from coating composition, that is, from the surface area of filler particles in the coating. The approach has been applied to two polymer-'plasticizer'-filler coating systems, where the filler content of each is below the generally acknowledged critical pigment volume concentration of the coating. Application of these coating systems to 0.0254 cm thick (10 mil) fuel-cell grade asbestos sheet produces inexpensive, flexible, microporous separators that perform at least as well as the original inorganic-organic concept, the Astropower separator.

Sheibley, D. W.↗

Effects of wing modification on an aircraft's aerodynamic parameters as determined from flight data

A study of the effects of four wing-leading-edge modifications on a general aviation aircraft's stability and control parameters is presented. Flight data from the basic aircraft configuration and configurations with wing modifications are analyzed to determine each wing geometry's stability and control parameters. The parameter estimates and aerodynamic model forms are obtained using the stepwise regression and maximum likelihood techniques. The resulting parameter estimates and aerodynamic models are verified using vortex-lattice theory and by analysis of each model's ability to predict aircraft behavior. Comparisons of the stability and control derivative estimates from the basic wing and the four leading-edge modifications are accomplished so that the effects of each modification on aircraft stability and control derivatives can be determined.

Hess, R. A.↗

On a finite-state inflow application to flap-lag-torsion damping in hover

An aerodynamic model with a coupled set of generalized dynamic wake equations and hybrid equations of motion for an elastic blade are applied here to a two-blade untwisted stiff in-plane hingeless small-scale model rotor with torsionally soft blades. Blade root offset, precone, blade droop, pitch control stiffness, and blade pitch angle are included in the model rotor. Numerical results show that 3D tip relief effects within the nonuniform steady-state inflow are significant to predict steady-state aerodynamic loads and blade deflections. Eigenvalue results confirm the importance of unsteady 3D aerodynamics in predicting lead-lag damping and frequency. Eigenvector analysis correlations reinforced qualitative and quantitative shortcomings associated with quasi-steady 2D aerodynamic theory for aeroelastic applications in hover.

De Andrade, Donizeti↗

Voluntary Consensus Organization Standards for Nondestructive Evaluation of Thin-Walled Metallic Liners and Composite Overwraps in Composite Overwrapped Pressure Vessels

NASA fracture control requirements outlined in NASA-STD-5009 and NASA-STD-5014 are predicated on the availability and use of sensitive nondestructive evaluation (NDE) methods that can detect and monitor defects, thereby providing data that can be used to predict failure or reduce the risk of failure in fracture critical components. However, in the case of composite materials and components, including composite overwrapped pressure vessels (COPVs), the effect of defects is poorly understood, the NDE methods used to evaluate locate and size defects are typically at lower technical readiness level than analogous NDE methods used for metals, and demonstration studies to verify the probability of detection (POD) are generally lacking or unavailable. These factors together make failure prediction of fracture critical composite materials and components based on size, quantity, or orientation of defects nearly impossible. Also, when inspecting metal liners in as-manufactured COPVs, sensitivity is lost and only the inner surface of the liner is accessible. Also, NDE of COPVs as applied during manufacturing varies significantly from manufacturer to manufacturer and has not yet been standardized. Although requirements exist to perform NDE immediately after manufacturing to establish initial integrity of the parts, procedural detail for NDE of composites is still nonexistent or under development. For example, in practice, only a visual inspection of COPVs is performed during manufacturing and service, leaving in question whether defects of concern, for example, bridging, overwrap winding anomalies, impact damage below visible threshold, out-of-family strain growth, and liner buckling have been adequately detected and monitored. To address these shortcomings, in 2005 the NASA Nondestructive Evaluation Working Group (NNWG) began funding work to develop and adopt standards for nondestructive evaluation of aerospace composites in collaboration with the American Society for Testing and Materials (ASTM) Committee E07 on Nondestructive Testing. Similarly, in 2006 the NASA Engineering and Safety Center (NESC) recommended that nondestructive evaluation methods that can predict composite failure in COPVs should be developed and verified, and integrated into the damage control plan for these vessels

Waller, Jess↗

Health Monitoring and Prognostics for More Electric Aircrafts

As more and more electric vehicles emerge in our daily operation progressively, a very critical challenge lies in the prediction of remaining flying time/distance (for aircraft). This information is important, particularly in the case of unmanned vehicles, because such vehicles can become self-aware, autonomously compute its own capabilities, and identify how to best plan and successfully complete vehicular missions safely. In case of electric aircrafts, computing remaining flying time is also safety-critical, since an aircraft that runs out of battery charge while in the air will eventually lose control leading to catastrophe. In order to tackle and solve the prediction problem, it is essential to have awareness of the current state and health of the system, especially since it is necessary to perform condition-based predictions. To be able to predict the future state of the system, it is also required to possess knowledge of the current and future operations of the vehicle. Given models of the current and future system behavior, the general approach of model-based prognostics can be employed as a solution to the prior stated prediction problem.For electric aircraft, propulsion is based on power generated from batteries. Thus, it is critical to monitor battery state charge and to estimate the ability of the battery to support mission activities as it is being discharged during flight operation. The ability of the vehicle to complete its given mission very much depends on the charge left in the batteries based on its operational route, maneuvering, weather conditions along with aging health of the batteries. Hence, for the purpose this discussion, consider the scenario of an unmanned electric aircraft that has some planned sequence of waypoints to reach throughout its mission. In such a scenario, for this particular aircraft, and within the region it is flown, at most two minutes are required to safely land the aircraft. Thus, it is desired to predict at which point in time the aircraft must begin to head to the runway and land.

Goebel, Kai↗

Predicting core transport in ITER baseline discharges with neon injections

Achieving self-consistent performance predictions for ITER requires integrated modeling of core transport and divertor power exhaust under realistic impurity conditions. We present results from a systematic power-flow and impurity-content study for the ITER 15 MA baseline scenario constrained directly by existing SOLPS-ITER neon-seeded divertor solutions. Using the OMFIT STEP workflow, stationary temperature and density profiles are predicted with TGYRO for $1.5 \unicode{x2A7D} Z_\textrm{eff} \unicode{x2A7D} 2.5$, and the corresponding power crossing the separatrix $P_\textrm{sep}$ is evaluated. We find that $P_\textrm{sep}$ varies by more than a factor of 1.7 across this scan and matches the ${\sim}100$ MW SOLPS-ITER prediction when $Z_\textrm{eff} \simeq 1.6$ or when auxiliary heating is reduced to ${\sim}75\%$ of nominal. Rotation-sensitivity studies show that plausible variations in toroidal flow magnitude modify $P_\textrm{sep}$ by $\lesssim 20\%$, while AURORA modeling confirms that charge-exchange radiation inside the separatrix is dynamically negligible under predicted ITER neutral densities. These results identify a restricted compatibility window, $Z_\textrm{eff} \approx 1.6$ –1.75 and $0.75 \lesssim f_{P_\textrm{aux}} \unicode{x2A7D} 1.0$, in which core transport predictions remain aligned with neon-seeded divertor protection targets. This self-consistent, model-constrained framework provides actionable guidance for impurity control and auxiliary-heating scheduling in early ITER operation and supports future whole-device scenario optimization.

ITER↗

DEVELOPMENT OF CONTROLLED PITCH NANO ARRAYS FOR APPLICATION IN NANO SCALE BASED PROPORTIONAL COUNTERS

Proportional counters (PCs) are a type of gas-filled radiation detection device capable of distinguishing between a wide range of radiation types and energies. In this application, however, these devices are limited by high power consumption and high bias potentials required to operate in the proportional detection regime. Previous work performed with a single carbon nanotube (CNT) anode has shown that nanoscale-based PCs can operate at bias potentials of 10V rather than the 1000V range required for PCs. ''Proof of concept'' experiments with a single CNT as the anode exhibit a small detection volume and consequently required long count times (24 hrs). To make this a practical detector technology (i.e., decrease the count time), the effective detection volume has to be increased. Experimental data and electric field modeling show that if the pitch (spacing between individual nanotubes) of the arrays is too small, the electric field of the individual nanostructure will collapse and the nanoscale array will behaved as a single macro-scale field with the associated high bias potential required to reach the proportional region. Electric-field modeling of the affect of nanostructure pitch on the electric field distribution of these arrays predicted that a pitch of about two-and-a-times the height of the nanostructure was required to retain the nanoscale electric field. In this work, we report on the fabrication and electrical property testing of nanoscale arrays with a range of controlled pitches.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

The effect of oblique angle of sound incidence, realistic edge conditions, curvature and in-plane panel stresses on the noise reduction characteristics of general aviation type panels

Experiments and a theoretical analysis were conducted to predict the noise reduction of inclined and curved panels. These predictions are compared to the experimental results with reasonable agreement between theory and experiment for panels under an oblique angle of sound incidence. Theoretical as well as experimental results indicate a big increase in noise reduction when a flat test panel is curved. Further curving the panel slightly decreases the noise reduction. Riveted flat panels are shown to give a higher noise reduction in the stiffness-controlled frequency region, while bonded panels are superior in this region when the test panel is curved. Experimentally measured noise reduction characteristics of flat aluminum panels with uniaxial in-plane stresses are presented and discussed. These test results indicate an important improvement in the noise reduction of these panels in the frequency range below the fundamental panel/cavity frequency.

Grosveld, F.↗

Tribology-Structure Relationships in Silicon Oxycarbide Thin Films

Silicon oxycarbide is a versatile material system that is attractive for many applications because of its ability to tune properties such as chemical compatibility, refractive index, electrical conductivity, and optical band gap through changes in composition. One particularly intriguing application lies in the production of biocompatible coatings with good mechanical properties. In this paper, we report on the wide range of mechanical and tribological property values exhibited by silicon oxycarbide thin films deposited by reactive radio frequency magnetron sputtering. Through a change in oxygen partial pressure in the sputtering plasma, the composition of the films was controlled to produce relatively pure SiO2, carbon-doped SiC, and compositions between these limits. Hardness values were 8-20 GPa over this range and the elastic modulus was measured to be between 60 and 220 GPa. We call attention to the fit of the mechanical data to a simple additive bond-mixture model for property prediction. Tribological parameters were measured using a ball-on-disk apparatus and the samples exhibited the same general trends for friction coefficient and wear rate. One film is shown to produce variable low friction behavior and low wear rate, which suggests a solid-state self-lubrication process because of heterogeneity on the nanometer scale.

36 MATERIALS SCIENCE↗