Search NASA⌕ Search

SEARCH · Search NASA

Results for “level set”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42

Digital pixel test structures implemented in a 65 nm CMOS process

The ALICE ITS3 (Inner Tracking System 3) upgrade project and the CERN EP R&D on monolithic pixel sensors are investigating the feasibility of the Tower Partners Semiconductor Co. 65 nm process for use in the next generation of vertex detectors. The ITS3 aims to employ wafer-scale Monolithic Active Pixel Sensors thinned down to 20–40 µm and bent to form truly cylindrical half barrels. Among the first critical steps towards the realisation of this detector is to validate the sensor technology through extensive characterisation both in the laboratory and with in-beam measurements. The Digital Pixel Test Structure (DPTS) is one of the prototypes produced in the first sensor submission in this technology and has undergone a systematic measurement campaign whose details are presented in this article. The results confirm the goals of detection efficiency and non-ionising and ionising radiation hardness up to the expected levels for ALICE ITS3 and also demonstrate operation at + 20 °C and a detection efficiency of 99% for a DPTS irradiated with a dose of 10 15 1 MeV n eq cm -2 . Furthermore, spatial, timing and energy resolutions were measured at various settings and irradiation levels.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Photovoltaic-assisted heat pump water heater system and method

A solar power system has a photovoltaic module that supplies electrical current derived from sunlight to a heater system of a hot water tank. The heater system uses the electrical energy from the photovoltaic module, and optionally also from a local power grid, to heat water up to a selected maximum stored hot water temperature. Control circuitry senses when the level of electrical power is below a threshold solar-power level, and in response sets the stored hot water temperature for the heater system to a first lower temperature value. The control circuitry also senses when the level of electrical power is above the threshold solar-power level, an in response sets the stored hot water temperature for the heater system to a second elevated temperature value higher than the lower temperature, making advantageous use of solar power when available. A mixing unit adds cold water to set the dispensed water temperature.

14 SOLAR ENERGY↗

A theoretical investigation of the (0001) covellite surfaces

We report on the properties of the (0001) covellites surfaces, which we investigate by periodic slab density functional theory calculations. The absolute surface energies have been computed for all bulk terminations, showing that surfaces terminated by the flat CuS layer are associated with the lowest surface energy. Cleavage is predicted to occur across the [0001] interlayer Cu–S bond. The surfaces obtained by lowest energy cleavage are analyzed in terms of the atomic vertical relaxation, workfunction, and surface band structure. Our study predicts the presence of a shallow p{sub z}-derived surface state located 0.26 eV below the Fermi level, which is set to play an important role in the surface reactivity of covellite.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A Statistical Approach to Establishing Subsystem Environmental Test Specifications

Results are presented of a research task to evaluate structural responses at various subsystem mounting locations during spacecraft level test exposures to the environments of mechanical shock, acoustic noise, and random vibration. This statistical evaluation is presented in the form of recommended subsystem test specifications for these three environments as normalized to a reference set of spacecraft test levels and are thus suitable for extrapolation to a set of different spacecraft test levels. The recommendations are dependent upon a subsystem's mounting location in a spacecraft, and information is presented on how to determine this mounting zone for a given subsystem.

Keegan, W. B.↗

The Classical Equations of Motion of Quantized Gauge Theories, Part I: General Relativity

In this and a companion paper, we show that quantum field theories with gauge symmetries permit a broader class of classical dynamics than typically assumed. In this article, we show that the dynamics extracted from the path integral or Hamiltonian formulation of general relativity allows for classical states that do not satisfy the full set of Einstein's equations. This amounts to loosening the Hamiltonian and momentum constraints that are imposed on the initial state. Nevertheless, the quantum theory permits gauge invariant time evolution of these states. The time evolution of these states is such that at the classical level the full set of Einstein's equations would appear to hold, with the physical effects of these states being attributable to an auxiliary, covariantly conserved energy-momentum tensor with no internal degrees of freedom. We derive the generalized Einstein equations for these states and show that a homogeneous and isotropic initial background state contributes to expansion identical to cold dark matter. The inhomogeneous components of this state could source curvature perturbations that grow linearly at linear order. This auxiliary contribution to Einstein's equations could have either sign and thus provide a trivial way to violate the null energy condition, enabling novel gravitational dynamics such as cosmic bounces and wormholes.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Designing of transparency windows by quantum interference of wave packets

It has been shown that control over the design of single- or multimode-transparency windows can be achieved by control-probe quantum interferometry using two delayed phase-locked ultrashort pulses. We have investigated how single- or multimode-transparency windows can be designed by eliminating the absorption to a set of odd or even vibrational levels of a molecule covered by the spectral bandwidth of the pulses. Suppression of absorption can be achieved by controlling the quantum interference of two vibrational wave packets excited by these two pulses, leading to destructive interference of transition amplitudes for one set of vibrational levels even or odd. Simuntaneously the interference becomes constructive for the other set of odd or even vibrational levels, leading to absorption to these levels. Thus, a set of transparency windows is designed in between two absorption peaks at two consecutive odd (even) vibrational levels by eliminating absorption at even (odd) vibrational levels between two absorption peaks. If the spectral bandwidth of the pulse [full width at half maximum (FWHM)] is less than the energy difference between two consecutive absorption peaks, the pulse will be transmitted without absorption through the transparency window. However, for pulses with a larger spectral bandwidth (FWHM), a set of broad transparency windows will be generated and different bands of pulse frequencies will be transmitted through these windows. We have shown that coherent control of the design of transparency windows can be achieved by controlling pulse duration, carrier frequency, delay, and the phase difference of two ultrashort pulses.

74 ATOMIC AND MOLECULAR PHYSICS↗

Population of the giant pairing vibration

Background: We present that the giant pairing vibration (GPV), a correlated two-nucleon mode in the second shell above the Fermi surface, has long been predicted and expected to be strongly populated in two-nucleon transfer cross sections similar to those of the normal pairing vibration. Recent experiments have provided evidence for this mode in 14,15 C but, despite sensitive studies, it has not been definitively identified in either Sn or Pb nuclei where pairing correlations are known to play a crucial role. Purpose: Our aim is to test whether features inherent to the mixing of bound and unbound levels might account for this and to study the effect in a simple and intuitively clear approach. Method: We study the mixing of unbound levels in a set of toy models that capture the essential physics of the GPV, along with a more realistic calculation including distorted-wave Born approximation transfer amplitudes. Results: The calculated (relative) cross section to populate a simulated GPV state is effectively low, compared to the case of bound levels with no widths Conclusions: The mixing turns out to be only a minor contributor to the weak population. Rather, the main reason is the melting of the GPV peak due to the width it acquires from the low orbital angular momentum single-particle states playing a dominant role in two-nucleon transfer amplitudes. Lastly, this effect, in addition to a severe Q-value mismatch, may account for the elusive nature of this mode in (t,p) and (p,t) reactions.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Prediction of correlation energies using variational subspace valence bond

In the variational subspace valence bond (VSVB) [G. D. Fletcher, J. Chem. Phys. 142, 134112 (2015)] method, the electronic orbitals comprising the wave function correspond to chemically meaningful objects, such as bonds, lone pairs, atomic cores, and so on. Selected regions of a molecule (for example, a single chemical bond, as opposed to all the bonds) can be modeled with different levels of basis set and possible methods for modeling correlation from the other regions. The interactions between the components of a molecule (say, a bond and a neighboring orbital) can then be studied in detail for their impact on a chemical phenomenon while avoiding the expense of necessarily applying the higher levels and methods to the entire molecule. Here, this work presents the theoretical basis for modeling correlation effects between specific electron pairs by incorporating terms in the inter-electronic coordinates (“r 12 ”) into VSVB. The approach is validated with calculations on small systems using single-reference wave functions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Improved Search for a Higgs Boson Produced in Association with Z->l+l- in proton antiproton Collisions at sqrt(s) = 1.96 TeV

We present a search for the standard model Higgs boson produced with a Z boson in 4.1 fb{sup -1} of data collected with the CDF II detector at the Tevatron. In events consistent with the decay of the Higgs boson to a bottom-quark pair and the Z boson to electrons or muons, we set 95% credibility level upper limits on the ZH production cross section times the H {yields} b{bar b} branching ratio. Improved analysis methods enhance signal sensitivity by 20% relative to previous searches beyond the gain due to the larger data sample. At a Higgs boson mass of 115 GeV/c{sup 2} we set a limit of 5.9 times the standard model value.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Tethered Space Satellite-1 (TSS-1): Technical Roundabouts

In the early 1990's US and Italian scientists collaborated to study the electrodynamics of dragging a satellite on a tether through the electrically charged portion of Earth's atmosphere called the ionosphere. An electrical current induced in the long wire could be used for power and thrust generation for a satellite. Other tether uses include momentum exchange, artificial gravity, deployment of sensors or antennas, and gravity-gradient stabilization for satellites. Before the Tethered Space Satellite (TSS-1), no long tether had ever been flown, so many questions existed on how it would actually behave. The TSS consisted of a satellite with science experiments attached to a 12.5 mile long, very thin (0.10 inch diameter) copper wire assembly wound around a spool in the deployer reel mechanism. With the Space Shuttle at an altitude of 160 nautical miles above earth, the satellite was to be deployed by raising it from the Shuttle bay on a boom facing away from Earth. Once cleared of the bay, the deployer mechanism was to slowly feed out the 12-plus miles of tether. Scientific data would be collected throughout the operation, after which the satellite would be reeled back in. Pre-flight testing system level tests involved setting up a tether receiver to catch the 12.5 mile tether onto another reel as it was being unwound by the deployer reel mechanism. Testing only the reel mechanism is straightforward. This test becomes more complicated when the TSS is mounted on the flight pallet at Kennedy Space Center (KSC). The system level tests must be passed before the pallet can be installed into the Space Shuttle cargo bay. A few months before flight, the TSS payload had been integrated onto the Spacelab pallet and system level tests, including unreeling and reeling the tether, had been successfully completed. Some of this testing equipment was then shipped back to the contractor Martin Marietta. Systems-level load analyses, which cannot be run until all information about each payload is finalized, was run in parallel with the physical integration of the hardware into the Shuttle payload bay. The coupled loads analysis, as it is called, incorporates any updates to the model due to system level tests, and any changes that were found during integration. The coupled loads analysis revealed that a single bolt attaching the deployer reel mechanism to the support structure had a "negative margin" - which is an indication that it might fail during operation. Hardware certification rules do not allow for hardware to fly with negative margins, so this issue had to be resolved before the flight. Since there is conservatism in engineering analysis, there is an option to "waive" the margin requirement, and fly the experiment as is. On the other hand, a structural failure of one payload could have serious or catastrophic consequences to other payloads and possibly the mission. Minor design changes or fixes might be feasible within the payload bay prior to launch. Any major design changes that required the spooling test to validate the hardware, or for the pallet to be removed, would cause TSS not to be ready for the Shuttle launch.

O'Connor, Brian↗

Validation for 2D/3D registration I: A new gold standard data set

Purpose: In this article, the authors propose a new gold standard data set for the validation of two-dimensional/three-dimensional (2D/3D) and 3D/3D image registration algorithms. Methods: A gold standard data set was produced using a fresh cadaver pig head with attached fiducial markers. The authors used several imaging modalities common in diagnostic imaging or radiotherapy, which include 64-slice computed tomography (CT), magnetic resonance imaging using Tl, T2, and proton density sequences, and cone beam CT imaging data. Radiographic data were acquired using kilovoltage and megavoltage imaging techniques. The image information reflects both anatomy and reliable fiducial marker information and improves over existing data sets by the level of anatomical detail, image data quality, and soft-tissue content. The markers on the 3D and 2D image data were segmented using ANALYZE 10.0 (AnalyzeDirect, Inc., Kansas City, KN) and an in-house software. Results: The projection distance errors and the expected target registration errors over all the image data sets were found to be less than 2.71 and 1.88 mm, respectively. Conclusions: The gold standard data set, obtained with state-of-the-art imaging technology, has the potential to improve the validation of 2D/3D and 3D/3D registration algorithms for image guided therapy.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Constraining off-shell Higgs boson production and the Higgs boson total width using WW → ℓνℓν final states with the ATLAS detector

A measurement of off-shell Higgs boson production is performed in the H* → WW channel. The measurement uses a proton–proton collision dataset with an integrated luminosity of 140 fb -1 collected at a centre-of-mass energy of 13 TeV by the ATLAS detector at the Large Hadron Collider. Final states in which both W bosons decay leptonically are targeted, and events are categorised based on the flavour of the final-state leptons, the jet multiplicity, and the output of neural network-based classifiers. The data are found to be compatible with the Standard Model expectation. An observed (expected) upper bound on the 95 % symmetric confidence level interval is set on the rate of off-shell Higgs boson production at a value of 3.4 (4.4) times the Standard Model prediction. These results are combined with the results from the measurement of on-shell Higgs boson production in the same final states to obtain an observed (expected) upper bound at 95 % confidence level on the Higgs boson total width of 13.1 (17.3) MeV.

Aad, G. [Aix-Marseille Univ., Marseille (France)] ↗

The effects of pilot stress factors on handling quality assessments during US/German helicopter agility flight tests

Flight tests were conducted with two helicopters to study and evaluate the effects of helicopter characteristics and pilot and task demands on performance in nap-of-the-Earth flight. Different, low-level slalom courses were set up and were flown by three pilots with different levels of flight experience. A pilot rating questionnaire was used to obtain redundant information and to gain more insight into factors that influence pilot ratings. The flight test setups and procedures are described, and the pilot ratings are summarized and interpreted in close connection with the analyzed test data. Pilot stress is discussed. The influence of demands on the pilot, of the helicopter characteristics, and of other stress factors are outlined with particular emphasis on how these factors affect handling-qualities assessment.

Pausder, H. J.↗

The effects of pilot stress factors on handling quality assessments during US/German helicopter agility flight tests

Flight tests were conducted with two helicopters to study and evaluate the effects of helicopter characteristics and pilot and task demands on performance in nap-of-the-earth flight. Different, low-level slalom courses were set up and were flown by three pilots with different levels of flight experience. A pilot rating questionnaire was used to obtain redundant information and to gain more insight into factors that influence pilot ratings. The flight test setups and procedures are described, and the pilot ratings are summarized and interpreted in close connection with the analyzed test data. Pilot stress is discussed. The influence of demands on the pilot, of the helicopter characteristics, and of other stress factors are outlined with particular emphasis on how these factors affect handling-qualities assessment. Previously announced in STAR as N83-13114

Pausder, H.-J.↗

Computing Proximity to Threat Along Uncertain Trajectory to Support Urban Air Mobility

Many airspace threats affect the selection of a flight route, such as terrain, physical obstacles, adverse weather, and special-use airspace, among others. Threat avoidance during Urban Air Mobility (UAM) and Low Altitude Mobility (LAM) flights is especially challenging due to their lower cruising altitudes. These operations may be exposed to buildings, towers, trees, terrain undulations, etc., along much of their flight route. Moreover, these low-altitude flights in urban environments are expected to encounter very busy airspace, increasing the workload associated with threat avoidance. The Proximity to Threat (PtT) function aims to support onboard or remote pilots by computing the risk from geospatial threats in the airspace along an aircraft’s flight path. The threats are both static entities and dynamic airspace restrictions that have been modeled and stored in geo-referenced mapping databases. The flight path may be specified by waypoints, airways, or similar discrete route elements or by a time series of closely spaced position and altitude points. Flight path uncertainty can also be taken into account by assuming both the position and altitude to be sampled from two normal distributions, each being specified by a mean and variance. PtT uses this additional information to verify that the flight path remains clear of threats along a wider path or if a position is reached earlier or later than anticipated, assuring the pilot or operator that there will be an available safety margin even if the aircraft deviates due to one or more occurrences of unexpected wind gusts, mechanical failures, airspeed changes, collision avoidance maneuvers, etc. The client can specify an uncertainty confidence level to bound the set of trajectories evaluated for threats so that the confidence level corresponds to the client’s risk tolerance under the expected conditions. PtT can be used as a pre-flight planning tool to determine a safe route through known threats and in-flight to avoid emerging or changing threats. In this report, we present the PtT function, discuss how the trajectory uncertainty is incorporated into the PtT function, and describe the use of this PtT function in a representative scenario.

urban air mobility↗

Searches for a High mass Higgs boson produced in $p\bar{p}$ collisions at $\sqrt{s}=1.96$ TeV

In this Thesis the electro-weak spontaneous symmetry breaking of the Standard Model (SM) is studied by searching for the scalar Higgs particle in the proton antiproton collisions of the Tevatron collider, at the center of mass energy √s = 1.96 TeV. We report on the inclusive search for the Higgs boson decaying to two W bosons in the final state characterized by two charged leptons (e or μ) and two neutrinos. The analysis of 4.8 fb$^{-1}$ of data recorded by the Collider Detector at Fermilab (CDF) shows no evidence of its production. We set 95% Confidence Level upper limits on the production cross section as a function of the mass $m_H$ in the range 110 to 200 GeV/$c^2$. For $m_H$ = 165 GeV/$c^2$ the observed limit is 1.3 times the SM predicted cross section (σH); the expected limit, in absence of signal, is 1.2+0.6 -0.4σ(H). These limits are the most stringent ones set by a single experiment up to date, for $m_H$ > 130 GeV/c2.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

KIPM Detector Characterization in QUIET

Kinetic Inductance Phonon‑Mediated (KIPM) detectors are superconducting microwave resonators on silicon that sense bursts of energy through tiny shifts in their resonance. In this work, we installed new devices in the QUIET facility's cryogenic test setup and used a network analyzer to drive them across a range of power levels. At each setting, we measured the transmitted signal and fit it to a simple notch‑filter model, allowing us to extract key performance metrics. And despite the increased noise at low power, our model consistently captured the resonance behavior. We observed that the resonant frequency stayed stable across most powers, the device s internal quality factor improved with stronger signals, and its coupling strength peaked mid‑range before leveling off. Overall, these findings confirm the detector s performance, laying groundwork for future work on energy calibration with pulsed optical sources.

Savitala, Akash [Washington U., Seattle; Fermilab]↗

Interaction of copper impurity with radiation defects in silicon doped with boron

The spectrum of deep levels formed in boron-doped Czochralski-grown silicon single crystals as a result of interaction of radiation defects with copper impurity is studied. It is shown that, irrespective of the order of introduction of defects (both in the case of low-temperature copper diffusion into crystals preliminarily irradiated with electrons and in the case of irradiation of the samples contaminated with copper), the same set of deep levels appears. In addition to conventional radiation defects, three types of levels have been detected in the band gap of copper-containing crystals. These levels include the level E{sub v} + 0.49 eV (already mentioned in available publications), the level E{sub v} + 0.51 eV (previously not related to copper), and a level close to the donor level of a vacancy. Based on the analysis of concentration profiles, the interstitial carbonoxygen pair is excluded from possible precursors of the copper-containing center with level E{sub v} + 0.49 eV.

36 MATERIALS SCIENCE↗