Search NASA⌕ Search

SEARCH · Search NASA

Results for “microstructure characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42

Strength mechanisms and tunability in Al-Ce-Mg ternary alloys enabled by additive manufacturing

Al-Ce-based alloys are promising candidates for additive manufacturing (AM) due to their hot-cracking resistance and because they do not require heat treatment to obtain precipitation strengthening. Rapid solidification rates enabled by AM methods can lead to enhanced mechanical properties; however, the strengthening mechanisms over large composition ranges were unclear. Here, combinatorial synthesis by directed-energy deposition (DED) and hardness measurements were used to rapidly map the composition-dependent strength of the ternary Al-Ce-Mg system. Tensile testing and microstructure characterization of selected compositions were performed to elucidate the compositional dependence of the strengthening mechanisms. Al 11 Ce 3 precipitates were present in all cases, and the maximum hardness (1.25 GPa) was measured for the Al-8Ce-10Mg composition. A combination of (i) Hall-Petch strengthening, based on the FCC-matrix-phase cell size; (ii) particle strengthening, based on Al 11 Ce 3 volume fraction and size; and (iii) solid-solution strengthening, based on Mg composition of the matrix phase, were used to account for the measured strengths. Vickers hardness is shown to correlate well with ultimate tensile strength in these alloys, highlighting the value of surface-based techniques for rapid screening.

36 MATERIALS SCIENCE↗

Porthole die extrusion of aluminum 6063 industrial scrap by shear assisted processing and extrusion

Shear Assisted Processing and Extrusion (ShAPE) is presented as a new manufacturing technology for converting aluminum scrap directly into extruded products. In this work, a porthole die configuration is integrated within the rotating ShAPE process to extrude circular, square, trapezoidal, and two-cell trapezoidal profiles from aluminum alloy 6063 industrial scrap. This is the first time that a rotating billet has been used to impart severe plastic deformation (SPD) during extrusion of noncircular profiles. Microstructural characterization is presented for a trapezoidal profile having an average grain size of 6.7 µm in the as-extruded condition. Dimensional stability was evaluated by measuring wall thickness along the extrusion length; the thickness varied by <5%. Round tubes achieved yield strength (246.9 ± 10.4 MPa), ultimate tensile strength (270.8 ± 9.6 MPa), and uniform elongation (16.5 ± 2.4%) exceeding industry standards.

36 MATERIALS SCIENCE↗

Spall damage of a Ta particle-reinforced metallic glass matrix composite under high strain rate loading

We investigate deformation and damage of a Zr-based bulk metallic glass (BMG) and its Ta particle-reinforced composite (MGMC) under impact loading, as well as quasi-static tension for comparison. Yield strength, spall strength, and damage accumulation rate are obtained from free-surface velocity histories, and MGMC appears to be more damage-resistant. Scanning electron microscopy, electron back scattering diffraction and x-ray computed tomography, are utilized for characterizing microstructures, which show features consistent with macroscopic measurements. Different damage and fracture modes are observed for BMG and MGMC. Multiple well-defined spall planes are observed in BMG, while isolated and scattered cracking around reinforced particles dominates fracture of MGMC. Particle–matrix interface serves as the source and barrier to crack nucleation and propagation under both quasi-static and impact loading. Finally, deformation twinning and grain refinement play a key role in plastic deformation during shock loading but not in quasi-static loading. In addition, 3D cup-cone structures are resolved in BMG, but not in MGMC due to its heterogeneous stress field.

36 MATERIALS SCIENCE↗

Automated high-throughput tensile testing reveals stochastic process parameter sensitivity

The mechanical properties of additively manufactured metals tend to show high variability, due largely to the stochastic nature of defect formation during the printing process. This study seeks to understand how automated high throughput testing can be utilized to understand the variable nature of additively manufactured metals at different print conditions, and to allow for statistically meaningful analysis. This is demonstrated by analyzing how different processing parameters, including laser power, scan velocity, and scan pattern, influence the tensile behavior of additively manufactured stainless steel 316L utilizing a newly developed automated test methodology. Microstructural characterization through computed tomography and electron backscatter diffraction is used to understand some of the observed trends in mechanical behavior. Specifically, grain size and morphology are shown to depend on processing parameters and influence the observed mechanical behavior. In the current study, laser-powder bed fusion, also known as selective laser melting or direct metal laser sintering, is shown to produce 316L over a wide processing range without substantial detrimental effect on the tensile properties. Ultimate tensile strengths above 600 MPa, which are greater than that for typical wrought annealed 316L with similar grain sizes, and elongations to failure greater than 40% were observed. As a result, it is demonstrated that this process has little sensitivity to minor intentional or unintentional variations in laser velocity and power.

36 MATERIALS SCIENCE↗

Optimization of direct aging temperature of Ti free grade 300 maraging steel manufactured using laser powder bed fusion (LPBF)

Maraging steels are of interest to the tool and die industry owing to their high strength, toughness and machinability. Additive manufacturing technologies like laser powder bed fusion (LPBF) can result in a paradigm shift in the design of maraging steel tools. Here, the lack of precipitates, in combination with solute segregation and non-equilibrium microstructure in Grade 300 maraging steel fabricated via LPBF makes the steel amenable to strengthening via direct aging post fabrication instead of the conventional solution treatment and aging. In this study we have focused on optimizing the direct aging temperature for a Ti-free Grade 300 maraging steel fabricated via LPBF for two different aging times. Through strain hardening analysis and detailed microstructural characterization, we show that direct aging at a temperature of 440 °C for 6 h resulted in the best strength-ductility combination. Aging samples at a lower temperature or shorter time resulted in no strain hardening prior to necking as a result of lower fraction of reverted austenite, whereas aging samples at a higher temperature resulted in extensive recrystallization of martensite, coarsening of precipitates, and extensive austenite reversion, resulting in softening of the fabricated parts.

36 MATERIALS SCIENCE↗

Property enhancement of CoCrNi medium-entropy alloy by introducing nano-scale features

CoCrNi -medium-entropy alloy (MEA) has been widely investigated due to its superior mechanical properties that overcome strength-ductility tradeoff. Here we show further property enhancement of CoCrNi MEA by introducing nano-scale features. Both CoCrNi and oxide dispersion strengthened (ODS) CoCrNi are fabricated by mechanical alloying and spark plasma sintering. Microstructural characterization and mechanical testing of these nanostructured MEAs revealed that the nano-scale features significantly improves the strength of the alloys. In ODS-CoCrNi MEA, Y 2 Ti 2 O 7 oxides with an average diameter of 7.3 ± 3.2 nm are incoherent with the matrix, and a specific orientation relationship exists between Y 2 Ti 2 O 7 and the matrix, which is [011] Y 2 Ti 2 O 7 //[011]Matrix, (400) Y 2 Ti 2 O 7 //(200)Matrix and ($22\bar2$) Y 2 Ti 2 O 7 //($11\bar1$)Matrix. The recrystallization and grain growth processes are effectively suppressed by the introduction of Y 2 Ti 2 O 7 nanoparticles. Strengthening mechanism analyses indicate that the strength improvement of ODS-CoCrNi is mainly ascribed to the precipitation strengthening of Y 2 Ti 2 O 7 .

36 MATERIALS SCIENCE↗

Considering interplay between multiple physical phenomena to elucidate single crystal-like texture, phase transformations, and mechanical behavior of directed energy deposited SS316L

A widespread implementation of large scale additive manufacturing (AM) processes, such as wire arc-directed energy deposition (WA-DED) AM can transform the current manufacturing supply chain networks. Naturally, such implementation requires control of the microstructural attributes, such as texture and phase evolution in the processed alloys. Currently, the texture evolution in fusion-based AM (F-BAM) processes is majorly rationalized by the phenomena occurring only during solidification. However, such rationalization is insufficient for understanding the evolution of primary and secondary crystallographic orientations, and consequently, fails to offer a comprehensive understanding and control of overall texture in F-BAM processed alloys. To this end, we report a single crystal (SX)-like texture in WA-DED processed SS316L for the first time. Furthermore, we assess the physical phenomena that may lead to such unique microstructural evolution during WA-DED AM. Subsequently, using microstructural characterization spanning the build height and thermomechanical simulations we investigate the effect of competitive growth and epitaxial growth occurring during solidification and thermally induced plastic deformation occurring post solidification on the overall texture of WA-DED processed SS316L. A spatial variation in solidification pathway is also established and correlated with variation in undercoolings across the build. Tensile tests revealed a strong orientation dependence of deformation mechanisms with over 110% elongation to failure of specimens deformed along <011>. Such anisotropy is rationalized using Schmid's analysis of dislocation slip and deformation twinning. Importantly, overall, the mechanisms outlined in this work will facilitate an enhanced understanding and subsequent control of texture evolution, solidification behavior and mechanical behavior of WA-DED processed steels.

36 MATERIALS SCIENCE↗

Effect of Si impurities on microstructure and tensile properties of a cast Al-Mg-Fe alloy

Al-Mg alloys are attractive for structural castings owing to their superior strength and ductility in the as-cast state. However, given the tight tolerance for impurities, Al-Mg alloys produced from secondary sources still face multiple challenges. Here, we report the effect of increased Si impurity (0.05–1.6 wt%), which is commonly found in secondary Al sources, on microstructure and tensile properties of a cast Al-4.3Mg-1.6Fe (wt%) alloy, commercially referred to as Castaduct-42 alloy. Microstructural characterization revealed that Si addition increased the volume fraction, size, and aspect ratio of primary Al13Fe4 intermetallic particles as well as the volume fraction of other binary and ternary eutectic phases. Tensile testing results demonstrated that increasing Si impurities from 0.05 to 1.6 wt% reduced ductility from 14.3 ± 1.4 % to 2.2 ± 1.0 %. A particle cracking damage accumulation model coupled with failure analysis indicated primary Al13Fe4 intermetallic particles to be the major contributing factor to the deterioration in ductility with increasing Si content. Additionally, the stabilizing effect of Si on primary Al 13 Fe 4 was inconsistent with the CALPHAD calculation results based on existing CALPHAD databases which predict a slightly decreasing primary Al13Fe4 phase fraction with increasing Si concentration. This work provides new insights into the phase stability and mechanical behavior of the lesser studied Al-Mg-Fe-Si alloy system that will contribute to the development of sustainable cast Al-Mg based alloys.

36 MATERIALS SCIENCE↗

High-temperature lean Cu alloys with Cr-to-Nb atomic ratio of 2

Two Cu-Cr-Nb alloys, denoted as alloy 1 (comprising Cu-0.89 at% Cr-0.42 at% Nb) and alloy 2 (comprising Cu-1.84 at% Cr-0.99 at% Nb), were produced through a series of manufacturing processes including vacuum induction melting, melt spinning, consolidation, brazing, and baking, with both alloys aimed at achieving a nominal Cr-to-Nb atomic ratio of 2. Microstructural characterization using transmission electron microscopy and X-ray diffraction identified the cubic C15 Laves-phase Cr 2 Nb as the dominant precipitate in both alloys, cross-validated by thermodynamic calculations and atomistic simulation-based density functional theory (DFT). Besides cubic C15 Cr 2 Nb, hexagonal C14-phase Cr 2 Nb and α-BiF3 cubic structured Cr 3 Nb were also observed in the alloys, including a coherent interface formed between the Cr 3 Nb precipitate and the Cu matrix. The hardness of the alloys increases, and the electrical conductivity decreases with increasing alloying addition content; two practical equations described the trends. Further DFT simulations revealed that the electrical conductivity (conductance) of the Cu/Cr 2 Nb interface is an order of magnitude higher than the intrinsic Cu high-angle grain boundaries.

36 MATERIALS SCIENCE↗

New class of tritium breeders for fusion applications: Metal-reinforced composite breeders

Commercial fusion reactors operating on a D-T fuel cycle will require a steady supply of tritium to maintain the burning plasma required for continuous power generation. Since tritium has a short half-life, there is negligible natural abundance which necessitates fusion reactors to produce their own source of tritium. Tritium is most easily produced by surrounding a fusion reactor core with lithium (Li), which reacts under the intense neutron flux leaving the reactor core to form tritium and helium. Due to the hazards and technical challenges associated with surrounding a fusion reactor core with many tons of molten Li, other Li-bearing tritium breeder materials have been pursued. Unfortunately, most of the liquid breeders historically examined are exceedingly corrosive to reactor structural materials while many solid breeders in the form of ceramics are forced to make tradeoffs between Li content and mechanical integrity. In this work, to break the historic limit between Li-density and mechanical integrity of traditional solid breeders, a new class of solid tritium breeders is developed: metal-reinforced composite (MERC) breeders. Specifically, the high Li-density of lithium oxide (Li 2 O) is exploited through the addition of a metal reinforcing phase, producing a composite breeder material exhibiting high splitting tensile strength and quasi-ductility with a Li-density greater than other leading solid breeder candidates, including lithium orthosilicate (Li 4 SiO 4 ) and lithium metatitanate (Li 2 TiO 3 ). Mechanical testing, microstructural characterization, and neutronic simulation results are presented and discussed in light of fusion reactor design considerations.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Synchrotron small-angle X-ray scattering technique for battery electrode study

Structure dependent stability is a concern for the achievement of high energy density electrode with long cycling lifetime, especially for alloying-type and conversion-type anodes. Substantial alterations in volume upon discharge-discharge process leads to particle pulverization and continuous consumption of electrolyte. Moreover, the nucleation and growth mechanism of Li 2 O and Li 2 S, which determines the rate performance of Li-O 2 and Li-S batteries, are still understudy. Microstructure characterization techniques have been applied to disclose the structural changes of active material at different charge/discharge states. Synchrotron small-angle X-ray scattering (SAXS) attracts considerable attention because of the high flux, high time resolution and nondestructive characteristics. In addition, SAXS patterns provide statistics structural information of electrode at micrometer scale. The commonly used coin cell with punched holes simplifies the application of in situ/operando SAXS measurement. Here, this review discusses the research about the SAXS technique in the characterization of electrode in different batteries.

25 ENERGY STORAGE↗

The porosity surrounding carbides and second phase stringers in monolithic U-10Mo fuel plate after irradiation

Post-irradiation microstructure characterization plays an important role in qualifying the low-enriched uranium (LEU) monolithic U-10 wt%Mo plate-type fuel for United States high-performance research reactors (USHPRRs) program. Inhomogeneous features resulting from manufacturing and irradiation processes, including carbides, second phase stringers, and extensive void spaces caused by the combining of small porosities, may increase the risk of heat concentration in local regions of the fuel plate over the operating conditions. In this study, characteristics of carbides, stringers, and porosity after multiple levels of irradiation at varying fission densities were studied by electron microscopes to decipher the morphology of pores and the porosity evolution in U-10 wt%Mo. For carbides, the result shows that porosities start forming on UMo grain boundaries, then on UMo/carbides interfaces as the burn-up going higher. However, the porosities surrounding carbides grow larger than the ones on UMo grain boundaries. The porosities around the uranium carbides could interconnect to form larger void space. The study revealed that the void spaces larger than 5 µm were found around uranium carbides after high burnup, while no evidence was observed to support the similar voids formed near second phase stringers even though the size of the stringers (> 50 µm) was much larger than uranium carbides (< 20 µm). The evolution of porosities suggests that the formation of second phase stringers may not create more significant porosities compared to regular uranium carbides regions during fuel operating conditions.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Experiment design for the neutron irradiation of $\mathrm{PM-HIP}$ alloys for nuclear reactors

Here, this article describes the design of an Advanced Test Reactor (ATR) drop-in neutron irradiation experiment aiming to directly compare the performance of nuclear structural alloys fabricated by powder metallurgy with hot isostatic pressing (PM-HIP) against conventional casting or forging. There is growing interest in PM-HIP alloys for nuclear applications because of their microstructural uniformity, superior mechanical properties, and reduced dependence on welding and machining, compared to cast/forged alloys. Nuclear code-qualification of PM-HIP alloys requires neutron irradiation testing to demonstrate performance under relevant conditions. In this experiment, six nuclear structural alloys were irradiated: Ni-based alloys 625 and 690, Grade 91 ferritic steel, SA508 pressure vessel steel, and 304L and 316L austenitic stainless steels. The experiment is assembled into seven capsules in four test trains and irradiated in three ATR inboard A positions. Both the PM-HIP and cast/forged versions of each alloy were irradiated under nearly identical conditions for comparative purposes, to target doses of 1 ± 0.2 and 3 ± 0.2 dpa at temperatures of 300 ± 50 °C and 400 ± 50 °C. A thorough description of the experiment design and thermal, structural and neutronic analyses performed to ensure the targeted irradiation conditions are met is provided. Specimens were configured as small disks, compact tension specimens and tensile bars to facilitate post-irradiation examination (PIE) that will include mechanical testing, microstructure characterization, and fracture toughness testing. Given the considerations for ASTM standardized mechanical testing, comparative fluence and temperature across specimen pairs, and comprehensive PIE planning herein, this work serves as a template for future nuclear materials qualification experiment designs.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Lanthanide migration and immobilization in metallic fuels

It is recognized that the lanthanide fission products can enhance the fuel-cladding chemical interaction (FCCI), which is a key concern of using metallic fuels such as U-Zr in a sodium-cooled fast reactor. The present work conducts a critical review on the analysis of lanthanide functions in FCCIs. Available in-pile and out-of-pile data are first collected and analyzed, then the theories for lanthanide migration and redistribution in the fuel in operation are analyzed. For mitigating FCCIs, one of the effective method is applying fuel additives for immobilizing lanthanides. The review investigates four candidates of fuel additives (Pd, Sn, Sb and In), and it is concluded that Sb can be the best candidate among the four elements based on current available thermodynamic data and microstructure characterizations. Considering that FCCIs lead to formation of metallic alloys/compounds between lanthanides and steel cladding constituents (Fe, Cr, and Ni), the review also analyzes the thermodynamic data such as enthalpy of formation of the alloys and/or metallic compounds and identify the solidus temperature of each alloy.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Influence of hot isostatic pressing on the performance of aluminum alloy fabricated by ultrasonic additive manufacturing

Ultrasonic additive manufacturing (UAM) is a solid-state manufacturing technique employing principles of ultrasonic welding coupled with mechanized tape layering to fabricate fully functional parts. However, UAM-fabricated parts often exhibit a reduction in strength when loaded normal to the welding interfaces (Z-direction). Here, the effect of hot isostatic pressing (HIP) on UAM builds of aluminum alloy was explored. Tensile testing and microstructure characterization were conducted; it was established that HIP eliminated the brittle Z-direction fracture and improved the strength and ductility of the Z-direction specimens. HIP eliminated voids and produced recrystallized structure; however, welding interfaces survived the HIP treatment.

36 MATERIALS SCIENCE↗

A new magnesium sheet alloy and its multi-stage homogenization for simultaneously improved ductility and strength at room temperature

We report that a new Mg-2Zn-0.3Ca-0.2Ce-0.1Mn (ZXEM2000) alloy and a multi-stage homogenization process have been designed and developed based on CALculation of Phase Diagram (CALPHAD) modeling results and experimental validation. The new sheet alloy offers an excellent combination of ductility (about 29% elongation) and yield strength (157 MPa), promising room-temperature forming applications. Microstructure characterization reveals that the exceptional properties of this alloy are mainly attributed to the weak basal texture, fine average grain size and high density of nano-scale Mn and Mg 6 Zn 3 Ca 2 precipitates achieved through multi-stage heat treatment and thermomechanical processing.

36 MATERIALS SCIENCE↗

Thermal Stability and Mechanical Properties of Cold-Sprayed Nickel-Yttria Coating

The microstructural evolution under the extreme environments imposed during cold spray deposition of cermet coatings and the microstructural recovery during post-processing annealing treatments is rather complex and not well understood. Here, Ni-Yttria cermet coatings on an SS304 substrate were produced using cold spray technique, resulting in a bimodal grain structure. The grain growth, phase stability, hardness, and wear properties are observed in as-deposited and annealed (at 400 °C) Ni-Yttria and pure Ni coatings. A multimodal microstructural characterization using electron microscopy, and atom probe tomography shows the structural and compositional stability of yttria particles and Ni grains. A fragmentation of Y-rich particles and dispersion in Ni was observed, however, no forced mixing/dissolution of Y in Ni is detected. Nano-yttria dispersed within the Ni grains slowed the grain growth during annealing. After annealing, Yttria reinforced coating was 1.5 times harder and showed better thermal and mechanical stability compared to the Ni coating.

Gwalani, Bharat↗

Helium partitioning to the core-shelled Ta nanoclusters in nanocrystalline Cu-Ta alloy

In this work, a nanocrystalline (NC) Cu-10at.%Ta alloy is irradiated with helium at different temperatures to assess the stability and effectiveness of Ta nanoclusters in trapping helium and suppressing swelling. Advanced microstructural characterization of the room-temperature irradiated specimens indicated the presence of small He-bubbles (∼1-2 nm) at the peak damage depth mainly at the core and along the interface of Ta nanoclusters with Cu matrix. Few bubbles were found along grain boundaries, with much smaller bubbles homogenously distributed within the copper lattice. High-temperature irradiation exhibited bubbles of ∼3-5 nm, which were primarily associated with nanoclusters as compared to other locations, with no observed faceting of the bubbles. In conclusion, atom probe analysis confirmed helium partitioning to the Ta nanoclusters indicating the effective entrapment of these He atoms.

36 MATERIALS SCIENCE↗