Search NASA⌕ Search

SEARCH · Search NASA

Results for “microstructure characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42

Documentation Package Supporting Fabrication of Doped UO 2 Samples for MiniFuel Irradiation and Fission Gas Release Benchmarking

The Oak Ridge National Laboratory (ORNL) is looking into the fabrication of high performance UO 2 fuel candidates via the addition of dopants to the UO 2 . The addition of dopants is proposed to cause enlarged grains that will slow down fission gas release from the irradiated fuel pellet candidates. The Cr-doped UO 2 pellets were fabricated from a microspherical feedstock, and enlarged grains were observed during the microstructural characterization. Irradiation under the Miniature Fuel program in the High Flux Isotope Reactor at ORNL will enable the study of irradiation response of such potential fuel candidates and will allow fission gas release benchmarking for these fuel candidates.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Second Annual Progress Report on Correlation Between Microstructure and Mechanical Properties of Neutron-Irradiated Ferritic-Martensitic and Austenitic Steels

Ferritic-martensitic steels G92-2b (an optimized Grade 92 heat), NF616 and T91, and austenitic stainless steel 800H and its Grain Boundary Engineering (GBE)-treated version 800H-TMP (ThermoMechanical Processing) were irradiated in the High Flux Isotope Reactor (HFIR) of Oak Ridge National Laboratory (ORNL) and the Advanced Test Reactor (ATR) of Idaho National Laboratory (INL). Selected G92-2b samples were irradiated up to 14.66 dpa in the HFIR at two temperature ranges: 400–496.7°C and 683.3– 720°C. NF616 and T91 were irradiated in the ATR up to 8.16 dpa with the irradiation temperatures ranged from 241°C to 447.5°C. Alloy 800H and 800H-TMP samples were irradiated in both the HFIR and the ATR. Selected 800H and 800H-TMP samples had HFIR irradiation to 1.28 dpa at 580°C and ATR irradiation up to 9.12 dpa at 359°C to 431°C. Vickers hardness measurements, fractography, and microstructural characterization were performed on the selected samples in the Low Activation Materials Design and Analysis (LAMDA) laboratory. Radiation-hardening of G92-2b was observed at the lower doses and lower irradiation temperatures (400- 496.7°C), with GB03 (0.52 dpa at 400°C) and GB04 (7.44 dpa at ~490°C) showing ~12% and ~8% hardening, respectively. Softening by ~14% was observed for GB05 (14.66 dpa at 496.7°C). Radiationsoftening of G92-2b was more prevalent at the higher irradiation temperatures (683.3-~720°C), with GB10 (0.46 dpa at 683.3°C), GB11 (7.44 dpa at ~720°C), and GB12 (14.63 dpa at ~720°C) showing ~8%, ~8%, and ~40% softening, respectively. Radiation-hardening of NF616 and T91 was observed with the hardness increased by ~37% to ~65% depending on the irradiation doses and irradiation temperatures. Within the studied irradiation conditions of NF616 and T91, samples with a higher dose had a larger hardness after irradiation. All the tested alloy 800H and 800H-TMP samples in this work showed radiation-hardening by ~96±7% to ~152±10%. Alloy 800H-TMP tended to have slightly smaller radiation-hardening than alloy 800H. The fractography results of G92-2b sample GB03, GB10, and GB11, together with the previously characterized fractography of GB04, GB05, and GB12, indicated that the ductility of G92-2b was maintained up to 14.66 dpa at the lower irradiation temperatures of 400-496.7°C, while some loss of ductility (less necking) was observed for higher doses at the higher irradiation temperatures of 683.3-720°C. This agrees with the previously reported tensile test results of G92-2b, where the elongation of G92-2b was reduced at higher doses at the higher irradiation temperatures. Dimple sizes increased at higher doses, which are more evident at the higher irradiation temperatures of 683.3-~720°C. The fractography of NF616 sample D2 (2.96 dpa at 291.5°C), D4 (5.91 dpa at 359°C), and D6 (8.16 dpa at 431°C) indicated loss of ductility with negligible necking for sample D2, while ductile failure for samples D4 and D6. Fractography of alloy 800H and 800H-TMP samples in various irradiation conditions showed ductile failure with obvious necking. Dimples were observed, with some of them containing large Ti-rich particles, in all the 800H/800H-TMP samples. Electron backscatter diffraction characterization of GB12 indicated the recovery of the lath structure, which was generally replaced by an equiaxed grain structure. Transmission electron microscopy (TEM) characterization showed the presence of frequent M 23 C 6 (M = primarily Cr), MX (M = primarily V), spherical Nb(C,N) precipitates, and occasional Laves phase precipitates in the G92-2b samples. MX precipitates with sizes of 20-30 nm were observed at boundaries of smaller grains, indicating the pinning effect of the V-rich precipitates. The lath structure recovery was more evident at the higher irradiation temperatures (683.3-~720°C), with decreased densities of line dislocations and M23C6 precipitates. The irradiated T91 (TA04) showed the growth of M23C6 precipitates to 101 ± 40 nm from the initial 68 ± 22 nm in the unirradiated condition. Dislocation loops of both {100} and {111} types were present in TA04. TEM characterization was also performed on the irradiated 800H (N4, N5, N6, and AR2) and 800H-TMP (P4, P5, P6, and HG1). Accumulation of M 23 C 6 precipitates at grain boundaries was observed in all the xii 800H/800H-TMP samples, and the presence of Ti(C,N) precipitates at grain boundaries and in the matrix was observed in the irradiated 800H-TMP. Some Ti(C,N) precipitates are embedded in the M 23 C 6 precipitates, maintaining specific orientation relationships between the precipitates and between the precipitate and matrix. In addition, nanoscale Si-rich clusters were observed in the matrix of all the 800H/800H-TMP samples, with EDS Si maps tending to have a lower contrast in 800H-TMP samples. Atom probe tomography was conducted on the same samples, supported by a Rapid Turnaround Examination project under Nuclear Science User Facilities. The results are being analyzed to be integrated with the TEM results for a confident description of the γ’ precipitates. Dislocation loops also formed in all the 800H/800H-TMP samples. The density and the average size of dislocation loops were quantified to be in the order of 10 22 – 10 23 m -3 and 11.7 – 15.9 nm, respectively, in the ATR-irradiated 800H/800H-TMP samples. The loop densities in irradiated 800H were higher than that in irradiated 800H-TMP under the same irradiation conditions. Further systematic data analyses, together with some complementary experiments, will be pursued for these samples to foster peer-reviewed journal article publications.

36 MATERIALS SCIENCE↗

Post-Irradiation-Examination of the ORNL and LANL Samples

Ferritic-martensitic steel G92-2b (an optimized Grade 92 heat) and austenitic stainless steel 800H and its Grain Boundary Engineering (GBE)-treated version 800H-TMP (ThermoMechanical Processing) were irradiated in the HFIR. Ferritic-martensitic steel T91 was irradiated in the ATR. Selected G92-2b samples were irradiated up to 14.66 dpa at two temperature ranges: 400–496.7°C and 683.3–720°C. Selected 800H and 800H-TMP samples were irradiated to 1.28 dpa at 580°C. A selected T91 sample was irradiated to 6.5 dpa at 295°C. Vickers hardness measurements, fractography, and microstructural characterization were performed on the selected samples in LAMDA. Further systematic data analyses, together with some complementary experiments, will be pursued for these samples to foster peer-reviewed journal article publications.

36 MATERIALS SCIENCE↗

FY20 Status Report on Creep Rupture Testing to Support the Development of Alloy 709 Code Case

This report provides an update on the status of the creep rupture testing on the first commercial heat of Alloy 709 in support of the Alloy 709 Code Case development. A creep test laboratory has been set up at ANL that comprises of 15 indirectly loaded test frames capable of testing ASTM-size specimens of the commercial heat of Alloy 709. The systems are equipped with high temperature furnaces capable of operation up to 1000°C in an air environment. During FY18, uniaxial ASTM-sized creep specimens were fabricated from 9 Alloy 709 plates that were processed by AOD, ESR, and ESR-homogenized routes and subsequently solution annealed at 1050, 1100, and 1150°C, and creep-rupture tests were performed at 330MPa and 600°C. The test results led to the down selection of the ESR-1100°C condition to support the code case. In FY19, 15 creep-rupture tests of the ESR-1100°C material, requiring the use of Type K thermocouples, were initiated to support the 100,000-hour Code Case. 8 tests were completed in FY19. In FY20, 6 tests were completed at the time of writing this report. In addition, 1 more test were loaded in FY20, using Type S thermocouples, and was completed. This report presents the data from the completed tests in FY20 and also the microstructural characterization of the fractured specimens. The creep data enabled the preliminary analysis of the creep behavior of this material. The characterization showed that in brittle fractures, the pores were narrow and thin, and elongated in the direction perpendicular to the loading direction, while in ductile fractures, the pores were much rounder. Dense precipitates were observed in all the samples, the size of which grew with test temperature. Some of the precipitates could be identified to be M23C6 based on their cuboid shape.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Summary of the Postirradiation Examination of the First Samples from a MiniFuel Irradiation

An overview of postirradiation examination results for uranium nitride kernels and uranium nitride coated particles irradiated in the High Flux Isotope Reactor are presented. This is the first postirradiation examination of the MiniFuel irradiation vehicle that was recently developed to rapidly screen different nuclear fuel concepts. Observations on fission gas release, irradiation conditions and microstructure of the irradiated fuel show good fuel performance at the low burnup achieved in this initial irradiation. The burnup measured by mass spectrometry ranged from 5.9 to 10 MWd/kgU as was achieved after only 68 effective full power days of irradiation. Results from silicon carbide thermometry measurements further benchmarked the MiniFuel irradiation vehicle and indicated fuel was irradiated at temperatures ranging from 410-460°C. Extensive microstructural characterization on the irradiated fuel was performed and no significant irradiation induced changes were observed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Rapid Simulation of Irradiation Damage in PWR Internals (NSUF 2019 Milestone Report)

This document summarizes the progress made by Oak Ridge National Laboratory (ORNL) in collaboration with the University of Michigan on “Rapid Simulation of Irradiation Damage in PWR Internals,” a research project led by the University of Michigan and supported by US Department of Energy Office of Nuclear Energy Nuclear Science User Facilities Consolidated Innovative Nuclear Research program. In this reporting period, samples that were exposed to combined neutron and ion irradiation were prepared and shipped to the University of Michigan for further analysis. This report summarizes the specimen preparation performed at ORNL’s Low Activation Materials Development and Analysis facility. The benchmarking work of microstructural characterization on reactor-irradiated samples with different dose levels was completed.

36 MATERIALS SCIENCE↗

Report on FY 2021 Fabrication and Testing of Qualified Alloy 709 Welds at ORNL

Alloy 709 is a candidate construction material for the Sodium Fast Reactor (SFR). As part of the Alloy 709 ASME Code Case development team under the Advanced Reactor Technologies (ART) Program, this work covers the development of the technical basis for weld fabrication and weld qualification of Alloy 709. This report summarizes the research conducted in FY 2021 and relevant results from previous reporting periods, aimed at welding commercial heat of Alloy 709 plates of relatively high phosphorous (P) level in support of ASME code case data package. Welding, code qualification tests, and associated microstructure characterization were carried out in determining the effect of P levels of weld wire on the weldability of the high P commercial heat of Alloy 709. The Alloy 709 weld creep strength was evaluated though preliminary creep testing.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Cooperative Research and Development Agreement among National Energy Technology Laboratory, Advanced Manufacturing LLC, and Connecticut Center for Advanced Technology [Abstract]

The National Energy Technology Laboratory (NETL), Advanced Manufacturing LLC (AMLLC) and Connecticut Center for Advanced Technology (CCAT) will collaborate to develop and manufacture cost-effective, oxide dispersion-strengthened, NiCrFeCo-rich high entropy alloys that are superior to Nickel-based superalloys (e.g. IN740) for repair or replacement service in extreme environments. The new alloys can result in higher efficiency and reduced cost of advanced power systems such as advanced ultra-supercritical (AUSC) boilers and gas turbines. High throughput, multiscale computational modeling will be performed to accelerate alloy discovery by interrogating the intrinsic properties of the alloys including thermodynamic, kinetic, and mechanical properties. Validation and evaluation will be performed, including additive manufacturing, microstructure characterization, and mechanical properties tests.

36 MATERIALS SCIENCE↗

Characterization and Modeling of Deformation Induced Damage in Titanium Alloys

Over the lifetime of their DOE support, and specifically during the past funding cycle, the PIs have primarily focused on ambient temperature studies of the mechanisms of heterogeneous deformation and shear transfer at GBs. The PIs have developed and applied a broad array of experimental approaches complemented by advanced computational methods and simulations to enable new understanding of GB shear transfer, and a new approach for modeling this behavior at the mechanistic level has been established. The PIs have examined how slip behavior differs on the surface and interior of polycrystals using a variety of approaches. Some of the associated data has been used to generate 3-D models of experimentally-characterized microstructures that both support interpretation of deformation mechanisms as well as reveal where modeling needs to be improved to more closely agree with what is experimentally observed. The PIs progress in constitutive modeling of crystal plasticity has introduced explicit GB resistance to shear that depends on the mutual geometry of active slip systems. This past work places the PIs in a good position to take on the challenges associated with mechanistically understanding the interplay between GBS and slip interactions.

42 ENGINEERING↗

Effect of thermal aging on microstructure and crack growth response of Alloy 152 weld

Nickel-based Alloy 690 and the associated weld Alloys 52 and 152 are typically used for nozzle penetrations in replacement heads for pressurized water reactor (PWR) vessels, because of their excellent overall resistance to general corrosion and environmental degradation, primarily stress corrosion cracking (SCC). However, many of the existing PWRs are expected to operate for 40-80 years. Likewise, advanced water-cooled small modular reactors (SMRs) will use Ni-Cr alloys and are expected to receive initial operating licenses for 60 years. Hence, the thermal stability of Ni-Cr alloys is a potential concern for the long-term performance of both existing and advanced nuclear power plants, and possibly spent fuel storage containers. The objective of this research is to understand the microstructural changes occurring in high-Cr, Ni-based Alloy 152 weldments during long time exposure to the reactor operating temperatures, and the effect of these changes on the service performance. One area of particular concern is the potential for long range ordering (LRO), i.e. formation of the intermetallic Ni2Cr phase under prolonged exposure to reactor temperatures and/or irradiation, which can increase strength, decrease ductility, and cause dimensional changes or lead to in-service embrittlement of components made with these alloys. Hence, this research focused on the microstructural evolution and the SCC response of Alloy 152 under accelerated thermal aging. The materials studied involved three heats of Alloy 152 used to produce a dissimilar metal weld (DMW) joining an Alloy 690 plate to an Alloy 533 low alloy steel (LAS) plate, thermally aged at three different temperatures (370°C, 400°C and 450°C) for up to 75,000h (equivalent to 60 years of service). The microstructural characterization by means of synchrotron X-ray did not find evidence of LRO in any of the three heats aged to an equivalent of 60 years of service. Testing in a primary water environment of a heat of Alloy 152 aged at 370°C to a 60-year service equivalent revealed a fatigue and corrosion fatigue crack growth responses similar to those measured on the un-aged alloy. However, the SCC CGR response of the aged sample appears to show a deterioration in performance.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Effect of thermal aging on microstructure and stress corrosion cracking behavior of Alloy 152 weldment

Nickel-based Alloy 690 and the associated weld Alloys 52 and 152 are typically used for nozzle penetrations in replacement heads for pressurized water reactor (PWR) vessels, because of their excellent overall resistance to general corrosion and environmental degradation, primarily stress corrosion cracking (SCC). However, many of the existing PWRs are expected to operate for 40-80 years. Likewise, water-cooled small modular reactors (SMRs) will use Ni-Cr alloys and are expected to receive initial operating licenses for 60 years. Hence, the thermal stability of Ni-Cr alloys is a potential concern for the long-term performance of both existing and advanced nuclear power plants, and possibly spent fuel storage containers. The objective of this research is to understand the microstructural changes occurring in high-Cr, Ni-based Alloy 152 weldments during long time exposure to the reactor operating temperatures, and the effect of these changes on the service performance. One area of particular concern is the potential for long range ordering (LRO), i.e. formation of the intermetallic Ni2Cr phase under prolonged exposure to reactor temperatures and/or irradiation, which can increase strength, decrease ductility, and cause dimensional changes or lead to in-service embrittlement of components made with these alloys. Hence, this research focused on the microstructural evolution and the SCC response of Alloy 152 under accelerated thermal aging. The materials studied involved three heats of Alloy 152 used to produce a dissimilar metal weld (DMW) joining an Alloy 690 plate to an Alloy 533 low alloy steel (LAS) plate, thermally aged at three different temperatures (370°C, 400°C and 450°C) for up to 75,000h (equivalent to 60 years of service). The microstructural characterization by means of synchrotron X-ray conducted in small, 0.2 mm - step line scans in the high-deformation regions of the weld root – covering areas spanning from the weld heat affected zone (HAZ) in Alloy 690 to the weld and weld butter on LAS - did not show evidence of LRO in any of the three Alloy 152 heats aged to an equivalent of 60 years of service. Testing in a primary water environment of two heats of Alloy 152 aged at 370°C to a 60-year service equivalent revealed a fatigue and corrosion fatigue crack growth responses similar to those measured on the un-aged alloys. However, the SCC CGR response of the aged samples appears to show a deterioration in performance, confirming our previous observation.

36 MATERIALS SCIENCE↗

Development of process parameters and post-build conditions for qualification of LPBF 316 SS

To harness the potential of laser powder bed fusion (LPBF) 316H stainless steel (SS) for use in advanced nuclear reactors, extensive research efforts are needed to develop optimal laser processing parameters and appropriate heat treatments, taking into account various manufacturing platforms and locations. Furthermore, it is crucial to assess the material properties in environments relevant to reactor operating conditions. In collaboration with Oak Ridge National Laboratory (ORNL) and Los Alamos National Laboratory (LANL), Argonne National Laboratory (ANL) is dedicated to gaining insights into how the manufacturing process and post-build treatments impact the performance of LPBF 316H SS. This report provides an overview of ANL's research findings for FY23, focusing on LPBF 316H SS produced using a Renishaw AM400 laser system. Specifically, our research has concentrated on three key areas: 1) Optimum laser processing parameters: Leveraging the high-throughput printing technology, we systematically varied the laser power, exposure time and point distance within the same build. By measuring the as-printed porosity, we identified an optimum printing parameter window that produced materials with near-complete density; 2) Post-built treatment development: Materials printed with the optimum laser parameters underwent treatments including stress relief, solution annealing, and hot isostatic pressing. Subsequently, we fabricated tension, creep, and fatigue specimens from materials subjected to these different conditions. Over the next year, a series of scoping tests will be conducted to facilitate the selection of the most suitable post-build treatment condition; 3) Thermal aging effects on microstructure and properties: thermal aging at 550°C, 650°C and 750°C was conducted on LPBF 316H SS specimens up to 2500 h. Microstructural characterization was performed with electron microscopy, and the evolution of the dislocation cell structures and secondary phases was studied. Microhardness tests and tension tests were conducted to quantify changes in mechanical properties. The results revealed that the aged LPBF 316H SS exhibited a high density of Cr-rich and Mo-rich fine precipitates within grains due to the presence of a high density of dislocations and the globally distributed dislocation cell structures, which served as heterogeneous nucleation sites for secondary phases. Along grain boundaries, a Mo-Cr-rich phase, observed in 750°C-aged conditions, displayed significant thermal coarsening. Throughout the aging process, various mechanisms, including stress relaxation, dislocation cell structure recovery, solution hardening, and precipitation hardening, competed to influence materials strength. These results contribute towards establishing the technical basis for qualifying LPBF 316H SS for advanced nuclear reactor applications.

36 MATERIALS SCIENCE↗

Progress on Producing an ODS Ferritic Alloy by High Deformation Processing of Reactive Powders

Oxide dispersion-strengthened (ODS) ferritic alloys, such as 14YWT, are considered as benchmarks for fuel cladding and core structural materials in advanced nuclear energy reactor systems that require high temperature strength and creep properties as well as resistance to radiation damage. Unfortunately, the popular processing method of mechanical alloying (MA) is time-consuming, incurs high manufacturing costs, and typically produces anisotropy in the microstructure and mechanical properties of ODS ferritic alloys. These considerations hinder their acceptance in many high-performance, high-temperature materials for advanced nuclear energy reactors. This work package is pursuing an alternative solid-state processing to MA involving high deformation at high temperatures for producing an ODS ferritic alloy for fuel cladding. This report summarizes the concept for this processing method and the progress toward selecting the reactive and ferritic alloy powders, preparing 316L stainless steel cans for filling with blended powder followed by degassing, and choosing the heat treatments and forging parameters for performing the first two forging experiments. The preliminary results of optical microscopy performed on polished samples that were cut in three orthogonal directions revealed remnant porosity in both samples. The analysis of the porosity using ImageJ revealed a lesser amount of ~2.49% in the HiLoMe-1 sample that was processed with the three heat treatments and forging parameters compared to ~5.70% for the Hi-1 sample that was processed with only the first sintering heat treatment and forging parameter. These initial results will provide insights that can be leveraged to improve the densification of the powders in future forging experiments that will be continued into FY24 for determining the optimum heat treatments and forging parameters coupled with detailed microstructure characterization studies for producing the ODS ferritic alloy.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Sensing and Control During Bulk SPP

In this work, we use the thermoelectricity to directly measure the temperature at different radial positions within instrumented Al1100 billets during friction extrusion. Site-specific and uninterrupted temperature measurements were possible by measuring the local voltages at several thermoelectric junctions consisting of aluminum-nickel pairs during extrusion. Measurements were conducted for a constant die rotation speed of 150 RPM and different extrusion feed rates of 2, 8, 32, and 80 mm.min-1. X-ray computed tomography was used to locate the positions of the thermoelectric junctions inside the processed billet, thus allowing for site-specific microstructural characterization at the precise measurement points. Smooth particle hydrodynamic modeling allowed to determine the thermal, strain, and strain rate fields developing during FE. The applicability and limitations of this temperature measurement approach are discussed as a function of the peak extrusion and torsion stresses relative to the matrix of extrusion feed rates.

42 ENGINEERING↗

Quality Optimization of Commercial FeCrAl Tube Production

The objectives of this report are to summarize the various process parameters and conditions that trigger premature failures during the production steps for Generation II ATF FeCrAl seamless tubes in commercially available manufacturing processes, and to suggest optimized processing routes and parameters to improve the quality and the material yield of commercial tube production. The production process steps include (1) the heat production process, (2) the master bar production process, and (3) the tube reduction process. For heat production, not only chemical composition control but also elimination of solidification defects in the vacuum induction–melted ingot are key. A hot-isostatic press helped in reducing and eliminating the internal, preexisting cracks in the ingot, which could be a source of premature failure (e.g., crack initiation from oxide particles) in the latter part of the tube production process. The master bars were produced by a hot-extrusion process. The area reduction ratio and the extrusion temperature are key to controlling the quality of the master bars and the grain structure. Because of the limited deformation ability of FeCrAl alloys, especially at ambient temperatures, a controlled, uniform grain structure with relatively small grains (<100 µm) is required at the beginning of the tube reduction process. Furthermore, a relatively small amount of area reduction per pass, combined with controlled inter-pass annealing, is important to achieve a reduction in failure events, a highly uniform wall thickness, concentricity, and a high-quality surface finish. Based on the knowledge obtained regarding process conditions, FeCrAl tube production with optimized process parameters is currently in progress. A portion of the final tube inventory was delivered in late June 2017. Cross-sectional microstructural characterization was completed for screening the quality of as-received tubes.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Preliminary results addressing material qualification using combined ion irradiation and modeling data

Additively-manufactured (AM) materials have attracted increasing attention in recent years as a new method to make novel and customized components. While AM and conventionally produced materials are compositionally similar, they do possess different microstructures, necessitating assessment of materials produced via AM for their behavior in reactor environments. Some microstructures unique to AM materials, such as compositional micro-inhomogeneity and dislocation cell structures, are of particular importance since they may lead to different radiation performance. The performance of AM materials for advanced nuclear reactor applications is of interest to the Advanced Materials and Manufacturing Technologies (AMMT) program under the Department of Energy Office of Nuclear Energy. The AMMT program aims to demonstrate its new accelerated development and qualification methods via laser powder bed fusion (LPBF) 316 stainless steel (SS). Focusing on material bearing both 316L and 316H specifications, we integrate ion irradiation and modeling. This year, we focus on answering foundational questions related to process variability, alloy chemistry variation, and microchemical segregation. Experimental results provide information and motivate questions to the modeling effort, which aims to develop the ability to model radiation-driven microstructural evolution in additively-manufactured 316 stainless steel under a variety of advanced reactor conditions, including different temperatures, neutron spectra, and fluxes, in a sort of "virtual experiment". We perform in-situ and ex-situ ion irradiations and microstructural characterizations to support the development of AM materials for reactor applications, develop a phase field model of radiation-induced segregation in additively manufactured material with high angle grain boundaries and dislocation cells, and investigate the effect of carbon and chromium content on point defect behavior.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Report Summarizing the Mechanical Properties of a Large ODS Ferritic Alloy Ingot by Forging at High Temperatures for Future Mother Tube Production

Oxide dispersion strengthened (ODS) ferritic alloys are considered the benchmark fuel cladding and core structural material in advanced nuclear energy reactors that require high-temperature strength and creep properties and resistance to radiation damage. The ODS ferritic alloys including 14YWT are produced by mechanical alloying (MA), which is time-consuming and is associated with high manufacturing costs that are not beneficial to being used in advanced nuclear energy reactors. This report summarizes the accomplishments in FY24 in the INM program for producing an ODS ferritic alloy by high-deformation, high-temperature processing of reactive and ferritic alloy powders for advanced reactor fuel cladding applications. Following four hot forging experiments, it was concluded that several significant challenges were encountered that were difficult to overcome. These challenges were related to using high annealing temperatures for pressure assisted sintering processes to produce dense microstructures, but the high annealing temperatures result in long range diffusion of Ti through the bcc Fe lattice and react with the YIG particles that are distributed on the prior surfaces of the ferritic alloy powders. In addition, it was determined that the high deformations induced by forging at high temperatures were not very effective for fracturing the reactive YIG particles into smaller particles and distributing them into the interior of the ferritic alloy powders. Spark plasma sintering was attempted for shortening the time at high temperatures, which led to full densification but the microstructure characterization results still showed that Ti atoms diffused over long distances in the bcc Fe lattice and reacted with the YIG particles. Finally, a short 30 minute high intensity ball milling experiment was conducted on blended 14WT and YIG powders for inducing severe deformations that caused the initially spherical powders of 14WT decorated with the YIG particles on the surfaces to transform to flakes and fracturing of YIG particles into smaller particles that were incorporated into the bcc Fe lattice. Two forgings were performed with the high intensity milled powders: first annealing for 20 minutes at 850ºC followed by forging and second annealing for 20 minutes at 1,100ºC followed by forging. At 850ºC, Ti atoms are effectively immobile, thus allowing for densification albeit incomplete. The deformation by forging after annealing for 20 minutes at 1,100ºC favored dynamic recrystallization processes that led to nano-size grains with very high stored energy due to high dislocation density. The corresponding VH data showed significant hardening that correlated with estimated strengthening of ~1650 MPa. This hybrid processing approach combining high intensity ball milling of powder with annealing and forging showed the most promise for producing an oxide dispersing strengthened ferritic alloy.

36 MATERIALS SCIENCE↗

Effect of Thermal Aging on Microstructure and Stress Corrosion Cracking Behavior of an Alloy 152 1st Layer Butter Weldment

Nickel-based Alloy 690 and the associated weld Alloys 52 and 152 are typically used for nozzle penetrations in replacement heads for pressurized water reactor (PWR) vessels, because of their excellent overall resistance to general corrosion and environmental degradation, primarily stress corrosion cracking (SCC). However, many of the existing PWRs are expected to operate for 40- 80 years. Likewise, water-cooled small modular reactors (SMRs) will use Ni-Cr alloys and are expected to receive initial operating licenses for 60 years. Hence, the thermal stability of Ni-Cr alloys is critical for the long-term performance of both existing and advanced nuclear power plants, and possibly spent fuel storage containers. The objective of this research is to understand the microstructural changes occurring in high-Cr, Ni-based Alloy 152 weldments during long time exposure to the reactor operating temperatures, and the effect of these changes on the service performance. One area of particular concern is the potential for long range ordering (LRO), i.e. formation of the intermetallic Ni2Cr phase under prolonged exposure to reactor temperatures and/or irradiation, which can increase strength, decrease ductility, and cause dimensional changes or lead to in-service embrittlement of components made with these alloys. Hence, this research focused on the microstructural evolution and the SCC response of Alloy 152 under accelerated thermal aging. The materials studied involved three heats of Alloy 152 used to produce a dissimilar metal weld (DMW) joining an Alloy 690 plate to an Alloy 533 low alloy steel (LAS) plate, thermally aged at three different temperatures (370°C, 400°C and 450°C) for different durations up to 75,000h (equivalent to 60 years of reactor service). The microstructural characterization by means of synchrotron X-ray conducted in small, 0.2 mm - step line scans in the high-deformation regions of the weld root – covering areas spanning from the weld heat affected zone (HAZ) in Alloy 690 to the weld and weld butter on LAS - did not show evidence of LRO in any of the three Alloy 152 heats aged at 370°C and 450°C to an equivalent of 60 years of service. However, the first weld butter layer has high levels of deformation and is highly susceptible to SCC even in its non-aged condition. Nanohardness testing confirmed the extreme hardening with aging (ΔHV ≅ 100) at two locations within this weldment. In absence of LRO, hardening is suspected to be due to thermally-induced Cr carbide precipitation and coarsening. Testing in a primary water environment of the 1st layer of Alloy 152 weld butter aged at 370°C to a 60-year service equivalent revealed a fatigue and corrosion fatigue crack growth responses similar to those measured on the un-aged alloys. Similarly, the SCC CGR response of the aged weld butter does not appear to show a deterioration in performance, however, the difficult-to-test weldment geometry may affect the test results.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗