Search NASA⌕ Search

SEARCH · Search NASA

Results for “module performance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

Development of coring procedures applied to Si, CdTe, and CIGS solar panels

Most of the research on the performance and degradation of photovoltaic modules is based on macroscale measurements of device parameters such as efficiency, fill factor, open-circuit voltage, and short-circuit current. Our goal is to develop the capabilities to allow us to study the degradation of these parameters in the micro- and nanometer scale and to relate our results to performance parameters. To achieve this objective, the first step is to be able to access small samples from specific areas of the solar panels without changing the properties of the material. In this paper, we describe two coring procedures that we developed and applied to Si, CIGS, and CdTe solar panels. In the first procedure, we cored full samples, whereas in the second we performed a partial coring that keeps the tempered glass intact. The cored samples were analyzed by different analytical techniques before and after coring, at the same locations, and no damage during the coring procedure was observed.

14 SOLAR ENERGY↗
DOE OSTI2024

Transport–Friendly Microstructure in SSC–MEA: Unveiling the SSC Ionomer–Based Membrane Electrode Assemblies for Enhanced Fuel Cell Performance

The significant role of the cathodic binder in modulating mass transport within the catalyst layer (CL) of fuel cells is essential for optimizing cell performance. This investigation focuses on enhancing the membrane electrode assembly (MEA) through the utilization of a short-side-chain perfluoro-sulfonic acid (SSC-PFSA) ionomer as the cathode binder, referred to as SSC-MEA. This study meticulously visualizes the distinctive interpenetrating networks of ionomers and catalysts, and explicitly clarifies the triple-phase interface, unveiling the transport-friendly microstructure and transport mechanisms inherent in SSC-MEA. The SSC-MEA exhibits advantageous microstructural features, including a better-connected ionomer network and well-organized hierarchical porous structure, culminating in superior mass transfer properties. Relative to the MEA bonded by long-side-chain perfluoro-sulfonic acid (LSC-PFSA) ionomer, noted as LSC-MEA, SSC-MEA exhibits a notable peak power density (1.23 W cm –2 ), efficient O 2 transport, and remarkable proton conductivity (65% improvement) at 65 °C and 70% relativity humidity (RH). These findings establish crucial insights into the intricate morphology-transport-performance relationship in the CL, thereby providing strategic guidance for developing highly efficient MEA.

25 ENERGY STORAGE↗
DOE OSTI2015

Moving Toward Quantifying Reliability - The Next Step in a Rapidly Maturing PV Industry: Preprint

Some may say that PV modules are moving toward being a simple commodity, but most major PV customers ask: 'How can I minimize chances of a module recall?' Or, 'How can I quantify the added value of a 'premium' module?' Or, 'How can I assess the value of an old PV system that I'm thinking of purchasing?' These are all questions that PVQAT (the International PV Quality Assurance Task Force) and partner organizations are working to answer. Defining standard methods for ensuring minimal acceptable quality of PV modules, differentiating modules that provide added value in the toughest of environments, and creating a process (e.g. through IECRE [1]) that can follow a PV system from design through installation and operation are tough tasks, but having standard approaches for these will increase confidence, reduce costs, and be a critical foundation of a mature PV industry. This paper summarizes current needs for new tests, some challenges for defining those tests, and some of the key efforts toward development of international standards, emphasizing that meaningful quantification of reliability (as in defining a service life prediction) must be done in the context of a specific product with design parameters defined through a quality management system.

14 SOLAR ENERGY↗
DOE OSTI2017

Investigation of Correlation between Field Performance and Indoor Acceleration Measurements of Potential Induced Degradation (PID) for c-Si PV Modules

The correlation between outdoor field testing and indoor chamber measurement for potential-induced degradation in crystalline silicon PV modules is unclear. The motivation of this work is to build up a direct comparison and investigate the correlation between indoor and outdoor performance. First of all, four PID indoor tests were defined from basic to premium, based on the difficulty of the test. Six groups of modules were designed and fabricated in Trina Solar, with different grades of PID resistance from weak to strong. The outdoor field test systems were built in three different climates: tropical, subtropical, and semi-arid climates in Singapore, Changzhou (China) and Golden (CO, USA) respectively, in a collaborative testing campaign involving Trina, SERIS and NREL. The system in Golden has been on-sun for more than 13 months where <4% power loss which includes PID and other reliability losses was detected and power loss of <2% is shown for all six groups of modules after 21 weeks in the field in the subtropical climate in Changzhou. However, PID of 23% was observed after 18 weeks in Singapore for the most PID-susceptible module, while the other PID module types showed degradation of only less than 5%.

14 SOLAR ENERGY↗
DOE OSTI2018

Yield Analysis and Comparison of GaInP/Si and GaInP/GaAs Multi-Terminal Tandem Solar Cells

We present a yield analysis of tandem devices consisting of GaInP top cells on Si or GaAs bottom cells with different terminal configurations. Inputs are the I-V and external quantum efficiency of the individual subcells and the irradiance-dependent module temperature of the bottom cell. Our model calculates the temperature of the tandem module by taking into account the performance, spectral working range and luminescent coupling of the different tandem devices, enabling an irradiance- and weather-dependent yield analysis for these modules. We apply the model to compare two types of two junction devices, a GaInP/GaAs monolithically grown tandem device, and a GaInP top cell stacked on a Si bottom cell, the present two best dual junction devices. When the subcells are series connected both technologies perform equally well. The performance of the GaInP/Si can be significantly improved relatively by 5.8% using 3-terminal (3T) devices with a back-contacted bottom cell instead of a 2T configuration, showing a possible benefit when using Si back contacted cells. For GaInP/Si, the 3T-device works as well as the 4T-device, enabling the integration of monolithic tandem cells into modules at comparably high efficiencies.

14 SOLAR ENERGY↗
DOE OSTI2024

CFD modeling of high-flux plate-and-frame membrane modules for industrial carbon capture

In this work, we study the application of membrane-based separation systems for carbon capture, considering plate-and-frame membrane modules. The successful deployment of membrane CO2 capture system relies on high-performing membranes as well as effective membrane modules that can fully exploit the developed membranes. A plate-and-frame membrane module is especially attractive for CO2 capture from industrial flue gas due to its lower pressure drop compared to its counterparts such as spiral wound modules and hollow fiber modules. To design better plate-and-frame modules, we investigate their basic unit - a single membrane stack through a combination of computational modeling and experimental investigations. The modeling approach is based on Computational Fluid Dynamics (CFD) to represent a multiphysics problem, including the fluid flow and diffusion processes within a membrane module. We use experimental data collected under different operating conditions to validate the CFD model. Numerical results suggest a good agreement between experiments and model outputs for the CO2 recovery, CO2 mole fraction in the retentate and permeate, and stage-cut. The CFD model is able to predict accurately the flow behavior, providing valuable insights on the effects of fluid dynamics on mass transfer of CO2. We also carry out a sensitivity analysis to identify the effect of key parameters on the CO2 recovery and the CO2 purity of the outlet streams.

Dosso, Cheick↗
DOE OSTI2018

Estimating the Effects of Module Area on Thin-Film Photovoltaic System Costs

We investigate the potential effects of module area on the cost and performance of photovoltaic systems. Applying a bottom-up methodology, we analyzed the costs associated with thin-film modules and systems as a function of module area. We calculate a potential for savings of up to 0.10/Wand0.13/W in module manufacturing costs for CdTe and CIGS respectively, with large area modules. We also find that an additional 0.04/W savings in balance-of-systems costs may be achieved. Sensitivity of the /W cost savings to module efficiency, manufacturing yield, and other parameters is presented. Lifetime energy yield must also be maintained to realize reductions in the levelized cost of energy; the effects of module size on energy yield for monolithic thin-film modules are not yet well understood. Finally, we discuss possible non-cost barriers to adoption of large area modules.

14 SOLAR ENERGY↗
DOE OSTI2018

Estimating the Effects of Module Area on Thin-Film Photovoltaic System Costs: Preprint

We investigate the potential effects of module area on the cost and performance of photovoltaic systems. Applying a bottom-up methodology, we analyzed the costs associated with thin-film modules and systems as a function of module area. We calculate a potential for savings of up to 0.10 dollars/W and 0.13 dollars/W in module manufacturing costs for CdTe and CIGS respectively, with large area modules. We also find that an additional 0.04 dollars/W savings in balance-of-systems costs may be achieved. Sensitivity of the dollar/W cost savings to module efficiency, manufacturing yield, and other parameters is presented. Lifetime energy yield must also be maintained to realize reductions in the levelized cost of energy; the effects of module size on energy yield for monolithic thin-film modules are not yet well understood. Finally, we discuss possible non-cost barriers to adoption of large area modules.

14 SOLAR ENERGY↗
DOE OSTI2019

Multi-Threaded Output in CMS using ROOT

CMS has worked aggressively to make use of multi-core architectures, routinely running 4- to 8-core production jobs in 2017. The primary impediment to efficiently scaling beyond 8 cores has been our ROOT-based output module, which has been necessarily single threaded. In this paper we explore the changes made to the CMS framework and our ROOT output module to overcome the previous scaling limits, using two new ROOT features: the \texttt{TBufferMerger} asynchronous file merger, and Implicit Multi-Threading. We examine the architecture of the new parallel output module, the specific accommodations and modifications that were made to ensure compatibility with the CMS framework scheduler, and the performance characteristics of the new output module.

Riley, Daniel↗
DOE OSTI2018

Performance of Low-Complexity Spectrally Selective One-Dimensional Mirrors for Photovoltaic Thermal Management

Operation at elevated temperatures is detrimental to the performance of crystalline Si solar modules. One method of reducing module operating temperature is selective reflection of sub-bandgap photons, which can otherwise only be absorbed parasitically. We numerically optimize the design of a series of multilayer photonic mirrors based on real materials using a previously developed optimization routine. Combined ray tracing and finite element simulations reveal the ability of each mirror to increase energy yield and decrease operating temperature. The best design outperforms a conventional glass antireflection coating, contains only nine layers, and maintains performance regardless of geographic location.

14 SOLAR ENERGY↗
DOE OSTI2021

A Miniature Multilevel Structures for Lossless Ion Manipulations Ion Mobility Spectrometer with Wide Mobility Range Separation Capabilities

Here, ion mobility spectrometry employing structures for lossless ion manipulations (SLIM-IMS) is an attractive gas-phase separation technique due to its ability to achieve unprecedented effective ion path lengths (>1 km) and IMS resolving powers in a small footprint. The emergence of multilevel SLIM technology, where ions are transferred between vertically stacked SLIM electrode surfaces, has subsequently allowed for ultralong single pass path lengths (>40 m) to be achieved, enabling ultrahigh resolution IMS measurements to be performed over the entire mobility range in a single experiment. The implementation of multiple SLIM levels requires very little additional space for the SLIM system, and we developed a miniature SLIM module (miniSLIM) based on multilevel SLIM technology and report the performance here. The module is 11.1 cm x 6.7 cm x 1.4 cm (L x W x H) and consists of three SLIM levels totaling 1-meter path length. Ion trajectory simulations were used to optimize the SLIM board spacings and SLIM board thicknesses of the miniSLIM IMS system. Methods of efficiently transferring ions between SLIM levels were examined and a new approach using asymmetric traveling waves (TWs) was developed and implemented in the miniSLIM. We experimentally characterized the performance of the --meter multilevel miniSLIM IMS-MS relative to a drift tube IM--MS using an Agilent tuning mixture and tetraalkylammonium cations. The 1-meter miniSLIM achieved a resolving power of up to 131 (CCS/ΔCCS), ~1.5x higher than achievable with a 78 cm path length drift tube IMS, and successfully transmitted the entire ion mobility range in a single separation. We also demonstrated the miniSLIM’s performance as a standalone IMS system (i.e., without MS), showing baseline separation between Agilent tuning mixture cations with the full mobility range observed, and a standard peptide mixture with different charge states readily differentiated. Overall the miniSLIM provides a compact alternative to high performance IMS instruments possessing similar path lengths.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2018

Performance of Low-Complexity Spectrally Selective One-Dimensional Mirrors for Photovoltaic Thermal Management: Preprint

Operation at elevated temperatures is detrimental to the performance of crystalline Si solar modules. One method of reducing module operating temperature is selective reflection of sub-band gap photons, which can otherwise only be absorbed parasitically. We numerically optimize the design of a series of multilayer photonic mirrors based on real materials using a previously developed optimization routine. Combined ray tracing and finite element simulations reveal the ability of each mirror to increase energy yield and decrease operating temperature. The best design outperforms a conventional glass antireflection coating, contains only nine layers, and maintains performance regardless of geographic location.

14 SOLAR ENERGY↗
DOE OSTI2019

An Experimental Reversed Heat Flux Investigation of the Helium-Cooled Modular Divertor with Multiple Jets

The Georgia Institute of Technology group has performed studies to characterize the thermal hydraulics of a single “finger” module of the helium-cooled modular divertor with multiple jets (HEMJ) proposed for long-pulse magnetic fusion reactors in a helium (He) loop designed with maximum mass flow rate of 10 g/s. However, testing divertor modules at prototypical heat fluxes and temperatures remains an engineering challenge. A new larger helium loop with a maximum mass flow rate of 100 g/s, suitable for evaluating helium-cooled divertors with larger surface areas such as a nine-finger HEMJ module, is currently being constructed. This work presents an experimental validation of a numerical model exploring the applicability of the “reversed heat flux approach,” which cools (versus heats) the plasma-facing surface of the divertor module to evaluate the helium-side heat transfer coefficient (HTC). The approach is to be used for performance evaluation of single and multiple modules of HEMJ in existing and future large helium loops. A cooling facility for producing a jet of water with a maximum mass flow rate of 1.4 kg/s at a maximum pressure of 0.4 MPa and temperature of 295 K (Re = 2.2 × 10 5 ) is described. Numerical and experimental results are presented for the heat flux and average helium impingement surface temperature over a range of water flow rates (0.5 to 1.4 kg/s) for heat fluxes as high as 5 MW/m 2 . The numerical model suggests that the HTC of the water impingement surface is comparable to or greater than that of the helium impingement surface. For given helium and water temperatures, the heat flux values are generally limited by conduction across the outer shell. These initial studies provide guidance on extending this approach to estimating the thermal-hydraulic performance of larger divertor module designs while reducing the challenges associated with studying such designs in the normal heating configuration at their extremely high prototypical temperatures and incident heat fluxes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

A proton beam energy modulator for rapid proton therapy

We present the design for a rapid proton energy modulator with radiofrequency accelerator cavities, which can deliver the proton radiation dose to varied depth in human tissues much faster than traditional mechanical beam energy degraders. The proton energy modulator is designed as a multi-cell 1-m long accelerator working at 2.856 GHz. Each individual accelerator cavity is powered by a 400 kW compact klystron to provide an accelerating/decelerating gradient of 30 MV/m. The high gradient is enabled by the individual power coupling regime, which provides a high shunt impedance. Beam dynamics simulations were performed, showing that the energy modulator can provide ±30 MeV of beam energy change for a 150 MeV, 7 mm long (full length) proton bunch, and the total energy spread of 3 MeV is satisfactory to clinical needs. A prototype experiment of a single cell has been built and tested, and the low-power microwave measurement results agree very well with simulations. The energy modulator is optimized for the 150 MeV cyclotron proton beam, while this approach can work with different beam energies.

47 OTHER INSTRUMENTATION↗
DOE OSTI2023

COLLABORATIVE DEVELOPMENT PROJECTS - PHOTONIC MEMORY CONTROLLER MODULE (P-MCM)

As computational density for high-performance computing and big-data services continues to scale, performance scalability of next generation computing systems is becoming increasingly constrained by limitations in memory access, power dissipation and chip packaging. The processor-memory communication bottleneck, a major challenge in current multicore processors due to limited pin-out and power budget, presents a detrimental scaling barrier to data-intensive computing. A consortium team of small businesses and leading researchers that includes experts from photonics processor-memory architecture, III/V photonic laser design/fabrication, silicon photonics design/fabrication, photonics packaging and assembly, and FPGA-based high-performance memory controller IP development – to collaboratively develop a commercialization path for a Photonic Memory Controller Module (P-MCM).

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2020

GPHS Module Pre-Impact test Temperature Prediction with ANSYS [PowerPoint]

The purpose of the project was to: Develop a finite element thermal model of the General Purpose Heat Source (GPHS) Module loaded with four fueled clads; Perform steady state analysis to validate the thermal model via energy balance; Perform transient thermal analysis to predict clad temperatures at various times; and, Transient model results will be used to inform module soak time needed to reach a desired clad temperature prior to impact.

42 ENGINEERING↗
DOE OSTI2024

The interactivity of sources and dietary levels of resistant starches – impact on growth performance, starch, and nutrient digestibility, digesta oligosaccharides profile, cecal microbial metabolites, and indicators of gut health in broiler chickens

In a 21-d study, 480 Cobb 500 (off-sex) male broiler chicks were used to investigate the effects of feeding different sources and levels of resistant starches (RS) on growth performance, nutrient and energy utilization, and intestinal health in broiler chickens. The birds were allocated to 10 dietary treatments in a 3 × 3 + 1 factorial arrangement. The factors were 3 RS-sources (RSS): banana starch (BS), raw potato starch (RPS), and high-amylose corn starch (HCS); each at 3 levels (RSL) 25, 50, or 100 g/kg plus a corn-soybean meal control diet. Birds and feed were weighed on d 0, 8, and 21. On d 21, samples of jejunal tissue and digesta were collected for chemical analysis. Data were analyzed using the mixed model procedure of JMP with factor levels nested with the control. In the 0 to 21 phase, the birds fed the RPS diets had higher (P = 0.011) FI than those fed HCS or control diets, and FCR was greater (P = 0.030) in birds that received BS diets than in other diets. RSS × RSL was significant (P < 0.05) for total tract nutrient retention, AME, and AMEn on d 21. The starch digestibility was higher (P < 0.001) in birds that received the control diet than in RS diets, and decreased as RS levels increased, except for HCS. The apparent metabolizable energy (AME) and nitrogen-corrected AME (AMEn) were higher (P < 0.001) in birds fed 100 g/kg HCS diet, with both decreasing with increasing levels of BS and RPS, except for HCS. Relative ileal oligosaccharides profile showed significant (P < 0.05) RSS × RSL with a higher relative abundance of Hex(3) (P = 0.01) and Pent(3) (P = 0.001) in HCS diets. In conclusion, RS may influence gut health and growth performance in broiler chickens through modulation of cecal SCFA and nutrient digestion, but these depend largely on the botanical origin and concentrations of individual RS.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2016

Encapsulation and backsheet adhesion metrology for photovoltaic modules

Photovoltaic modules are designed to operate for decades in terrestrial environments. However, mechanical stress, moisture, and ultraviolet radiation eventually degrade protective materials in modules, particularly their adhesion properties, eventually leading to reduced solar cell performance. Despite the significance of interfacial adhesion to module durability, currently there is no reliable technique for characterizing module adhesion properties. We present a simple and reproducible metrology for characterizing adhesion in photovoltaic modules that is grounded in fundamental concepts of beam and fracture mechanics. Using width-tapered cantilever beam fracture specimens, interfacial adhesion was evaluated on relevant interfaces of encapsulation and backsheet structures of new and 27-year-old historic modules. The adhesion energy, Gc [J/m 2 ], was calculated from the critical value of the strain energy release rate, G, using G = βP 2 , where β (a mechanical and geometric parameter of the fracture specimen) and P (the experimentally measured critical load) are constants. Under some circumstances where testing may result in cracking of brittle layers in the test specimen, measurement of the delamination length in addition to the critical load was necessary to determine G. Relative to new module materials, backsheet adhesion was 95% and 98% lower for historic modules that were exposed (operated in the field) and unexposed (stored on-site, but out of direct sunlight), respectively. Encapsulation adhesion was 87-94% lower in the exposed modules and 31% lower in the unexposed module. As a result, the metrology presented here can be used to improve module materials and assess long-term reliability.

14 SOLAR ENERGY↗