Search NASA⌕ Search

SEARCH · Search NASA

Results for “parameter continuation method”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42

Drop Axis Ratio Distributions in Stratiform and Convective Rain

A fully calibrated low profile 2D video disdrometer (2DVD) has been recording many different rainfall events in Northern Alabama (USA) since June 2007. An earlier publication reported drop shapes and axis ratio distributions determined for some of the events. For one of the cases examined, a noticeable shift in the 3.5 - 3.75 mm drop axis ratio distribution was noted. In this paper, we extend the earlier work by separating the 2DVD measurements into stratiform and convective rain. The separation is made possible by using the minute-by-minute drop size distribution (DSD) measured by the 2DVD. The 1-minute DSDs are fitted to a gamma distribution, and using a simple indexing technique which involves two of the fitted parameters, periods of convective and stratiform rain are separated for a given event. The output of the DSD indexing technique is qualitatively confirmed by comparing with simultaneous time series observations from a co-located UHF profiler which continuously records height profiles of reflectivity, Doppler mean and spectral width, all of which enable the identification of bright-band periods and, furthermore, periods of moderate and deep convection. Excellent consistency is found between the output of the DSD-based separation method and the profiler observations. Next, we utilize the output of DSD index-based separation method to flag the periods of severe convection for a given event. Drop axis ratios during the flagged periods are derived and compared with those during stratiform rain periods. Five cases have been considered. Axis ratio distributions do not show appreciable differences between stratiform and convective periods for four of the cases. The fifth case (the same case as reported earlier) shows a shift in the 3.5 - 3.75 mm drop axis ratios during a prolonged period of convection. The contoured shapes for these drops determined from the 2DVD camera data indicate the possibility of non-axisymmetric oscillations, compared with the contoured images for other events which fit well to our reference drop shapes. For all of above cases, observations from a C-band polarimetric radar - situated 15 km away are examined. The variations between the co-polar radar reflectivity and the differential reflectivity as well as the specific differential phase are compared with the 2DVD data based scattering calculations for the 5 events. The implications will be discussed.

Thurai, M.↗

Modified Geometric Truncation of the Scattering Phase Function

Phase function of light scattering on large atmospheric particles has very strong peak in forward direction constituting a challenge for accurate numerical calculations of radiance required in remote sensing problems. Scaling transformation replaces original phase function with a sum of the delta function and a new regular smooth phase function. Geometric truncation is one of the ways to construct such a smooth function. The replacement phase function coincides with the original one outside the forward cone and preserves the asymmetry parameter. It has discontinuity at the cone. Another simple functional form of the replacement phase function within the cone is suggested. It enables continuity and allows for a number of modifications. Three of them are considered in this study: preserving asymmetry parameter, providing continuity of the 1st derivative of the phase function, and preserving mean scattering angle. Yet another problem addressed in this study is objective selection of the width of the forward cone. That angle affects truncation fraction and values of the phase function within the cone. A heuristic approach providing unambiguous criterion of selection of the truncation angle is proposed. The approach has easy numerical implementation. Suggested modifications were tested on cloud phase function using discrete ordinates and Monte Carlo methods. It was shown that the modifications provide better accuracy of the radiance computation compare to the original geometric truncation with discrete ordinates while continuous derivative approach provides significant gain in computer time with Monte Carlo simulations.

Alexander Radkevich↗

Physics-Based Methods of Failure Analysis and Diagnostics in Human Space Flight

The Integrated Health Management (IHM) for the future aerospace systems requires to interface models of multiple subsystems in an efficient and accurate information environment at the earlier stages of system design. The complexity of modern aeronautic and aircraft systems (including e.g. the power distribution, flight control, solid and liquid motors) dictates employment of hybrid models and high-level reasoners for analysing mixed continuous and discrete information flow involving multiple modes of operation in uncertain environments, unknown state variables, heterogeneous software and hardware components. To provide the information link between key design/performance parameters and high-level reasoners we rely on development of multi-physics performance models, distributed sensors networks, and fault diagnostic and prognostic (FD&P) technologies in close collaboration with system designers. The main challenges of our research are related to the in-flight assessment of the structural stability, engine performance, and trajectory control. The main goal is to develop an intelligent IHM that not only enhances components and system reliability, but also provides a post-flight feedback helping to optimize design of the next generation of aerospace systems. Our efforts are concentrated on several directions of the research. One of the key components of our strategy is an innovative approach to the diagnostics/prognostics based on the real time dynamical inference (DI) technologies extended to encompass hybrid systems with hidden state trajectories. The major investments are into the multiphysics performance modelling that provides an access of the FD&P technologies to the main performance parameters of e.g. solid and liquid rocket motors and composite materials of the nozzle and case. Some of the recent results of our research are discussed in this chapter. We begin by introducing the problem of dynamical inference of stochastic nonlinear models and reviewing earlier results. Next, we present our analytical approach to the solution of this problem based on the path integral formulation. The resulting algorithm does not require an extensive global search for the model parameters, provides optimal compensation for the effects of dynamical noise, and is robust for a broad range of dynamical models. In the following Section the strengths of the algorithm are illustrated illustrated by inferring the parameters of the stochastic Lorenz system and comparing the results with those of earlier research. Next, we discuss a number of recent results in application to the development of the IHM for aerospace system. Firstly, we apply dynamical inference approach to a solution of classical three tank problems with mixed unknown continuous and binary parameters. The problem is considered in the context of ground support system for filling fuel tanks of liquid rocket motors. It is shown that the DI algorithm is well suited for successful solution of a hybrid version of this benchmark problem even in the presence of additional periodic and stochastic perturbation of unknown strength. Secondly, we illustrate our approach by its application to an analysis of the nozzle fault in a solid rocket motor (SRM). The internal ballistics of the SRM is modelled as a set of one-dimensional partial differential equations coupled to the dynamics of the propellant regression. In this example we are specifically focussed on the inference of discrete and continuous parameters of the nozzle blocking fault and on the possibility of an application of the DI algorithm to reducing the probability of "misses" of an on-board FD&P for SRM. In the next section re-contact problem caused by first stage/upper stage separation failure is discussed. The reaction forces imposed on the nozzle of the upper stage during the re-contact and their connection to the nozzle damage and to the thrust vector control (TVC) signal are obtained. It is shown that transient impact induced torquean be modelled as a response of an effective damped oscillator. A possible application of the DI algorithm to the inference of damage parameters and predicting fault dynamics ahead of time using the actuator signal is discussed. Finally, we formulate Bayesian inferential framework for development of the IHM system for in-flight structural health monitoring (SHM) of composite materials. We consider the signal generated by piezoelectric actuator mounted on composite structure generating elastic waves in it. The signal received by the sensor is than compared with the baseline signal. The possibility of damage inference is discussed in the context of development of the SHM.

Smelyanskiy, Vadim N.↗

Stopped, Bunched Beams for the TwinSol Facility

Tests of the unitarity of the Cabbibo-Kobayashi-Masakawa (CKM) matrix offer an important avenue for constraining the Standard Model of the electroweak interaction. Several methods are currently used to determine V-ud, the largest element in the top-row normalization test. One such method is through the study of superallowed T =1/2 mixed mirror transitions, which offers a complementary method to the current most-precise value that is determined from superallowed pure Fermi 0(+) 0(+) transitions. The precision currently achievable by this method is currently limited by the very low number of transitions for which the Fermi-to-Gamow-Teller mixing ratio has been measured. St. Benedict, the Superallowed Transition Beta-Neutrino Decay-Ion-Coincidence Trap, is currently under development at the University of Notre Dame's Nuclear Science Laboratory, and intends to determine for a range of new isotopes through measurements of the -neutrino asymmetry parameter a using a linear Paul trap. In order to trap these ions, the fast, continuous secondary beam separated by the TwinSol twin solenoid separator must be thermalized and bunched. The system through which this will be done will feature a large-volume gas cell in which the ions will be thermalized, a double-RF-funnel-based ion guide system for the extraction of the ions, and a radiofrequency quadrupole (RFQ) to provide cooled ion bunches for capture in the Paul trap.

beam cooling↗

Prenatal dichlorodiphenyldichloroethylene (DDE) exposure and child growth during the first year of life

Background: Due to its long-term persistence in the environment and its ability to cross the placental barrier, prenatal p,p Prime -dichlorodiphenyldichloroethene (DDE) exposure continues to be a public health concern. This study aimed to evaluate the association between prenatal DDE exposure and child growth, at birth and during the first year of life. Methods: 253 pregnant women were recruited between January 2001 and June 2005 in a prospective cohort in Morelos, Mexico. Serum levels of DDE were measured during each trimester of pregnancy by gas chromatography with an electron capture detector. Using the generalized mixed-effects models, the association between DDE and child growth parameters (weight-for-age, length-for-age, weight-for-length, BMI-for-age and head circumference-for-age Z-scores) from birth to 1 year of age was assessed. Maternal dietary intake was considered as covariable among others. Results: DDE levels were 6.3{+-}2.8 ng/mL (first trimester), 6.6{+-}2.9 ng/mL (second trimester), and 7.6{+-}2.9 ng/mL (third trimester). After adjusting for potential confounder variables, no significant associations were observed with prenatal DDE exposure and each of the selected parameters. Conclusions: Our results show no evidence of an association between prenatal DDE exposure and child growth during the first year of life.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Heralded Bell State of Dissipative Qubits Using Classical Light in a Waveguide

Maximally entangled two-qubit states (Bell states) are of central importance in quantum technologies. We show that heralded generation of a maximally entangled state of two intrinsically open qubits can be realized in a one-dimensional (1d) system through strong coherent driving and continuous monitoring. In contrast to the natural idea that dissipation leads to decoherence and so destroys quantum effects, continuous measurement and strong interference in our 1d system generate a pure state with perfect quantum correlation between the two open qubits. Though the steady state is a trivial product state which has zero coherence or concurrence, we show that, with carefully tuned parameters, a Bell state can be generated in the system's quantum jump trajectories, heralded by a reflected photon. Surprisingly, this maximally entangled state survives the strong coherent state input—a classical state that overwhelms the system. This simple method to generate maximally entangled states using classical coherent light and photon detection may, since our qubits are in a 1d continuum, find application as a building block of quantum networks.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Relationship between Surface Self-Diffusion and Bubble Mobility in Solids: Theory and Atomistic Simulation

Diffusion processes in solids are characterized by complex mechanisms occurring at the atomistic level. The relevant theoretical concepts are sufficiently developed in the case of the diffusion of point defects. At the same time, the diffusion of objects such as clusters of vacancies or nanometer-size cavities in the crystal lattice is described only in terms of continuous-medium approximation. This paper attempts to link the existing theory of diffusion of bubbles in a crystalline matrix with the atomistic description of the process on the basis of the molecular dynamics method. For simplicity, the diffusion of cavities in a two-dimensional Lennard-Jones lattice is considered. A controlled molecular dynamics method is proposed to speed up the direct computation of the diffusion rate of bubbles. Based on the results of simulation, a practical interpretation is given to a parameter of the continuum theory such as the rate of surface self-diffusion. The applicability range of the continuum theory is demonstrated, and principles for the refinement of the theory in the case of minimum-size bubbles are formulated.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

TOVS Pathfinder product validation and intercomparison

Validation and intercomparison is an essential part of the Pathfinder program. Since its organization within the International TOVS Working Group, the TOVS community has continuously emphasized this aspect of the product retrieval problem. In the previous sections of this report, the TOVS Pathfinder SWG has recommended a careful and coherent reorganization and archiving of TOVS radiance data, and three distinct pathways for deriving product variables from this TOVS radiance archive. The importance in taking this multiple path approach to creating climate datasets rests in our firm belief that there is now global 'absolute truth' data for any of the derived physical parameters. Each of the selected methods is based upon a different set of assumptions. The challenge in interpreting Pathfinder data is to determine what alterations in the physical attributes of the environment contribute to evidence of global change extracted from observed or derived Pathfinder datasets. The Pathfinder validation and intercomparison activity must include validation of the forward problem, by which one calculates an estimate of upwelling radiance information from given earth and atmospheric data, and validation of the inverse problem, by which one calculates estimates of earth and atmospheric information from given upwelling satellite spectral radiance data.

Source record↗

FAST Model Calibration and Validation of the OC5- DeepCwind Floating Offshore Wind System Against Wave Tank Test Data: Preprint

During the course of the Offshore Code Comparison Collaboration, Continued, with Correlation (OC5) project, which focused on the validation of numerical methods through comparison against tank test data, the authors created a numerical FAST model of the 1:50-scale DeepCwind semisubmersible system that was tested at the Maritime Research Institute Netherlands ocean basin in 2013. This paper discusses several model calibration studies that were conducted to identify model adjustments that improve the agreement between the numerical simulations and the experimental test data. These calibration studies cover wind-field-specific parameters (coherence, turbulence), hydrodynamic and aerodynamic modeling approaches, as well as rotor model (blade-pitch and blade-mass imbalances) and tower model (structural tower damping coefficient) adjustments. These calibration studies were conducted based on relatively simple calibration load cases (wave only/wind only). The agreement between the final FAST model and experimental measurements is then assessed based on more-complex combined wind and wave validation cases.

17 WIND ENERGY↗

FAST Model Calibration and Validation of the OC5-DeepCwind Floating Offshore Wind System Against Wave Tank Test Data

During the course of the Offshore Code Comparison Collaboration, Continued, with Correlation (OC5) project, which focused on the validation of numerical methods through comparison against tank test data, the authors created a numerical FAST model of the 1:50-scale DeepCwind semisubmersible system that was tested at the Maritime Research Institute Netherlands ocean basin in 2013. This paper discusses several model calibration studies that were conducted to identify model adjustments that improve the agreement between the numerical simulations and the experimental test data. These calibration studies cover wind-field-specific parameters (coherence, turbulence), hydrodynamic and aerodynamic modeling approaches, as well as rotor model (blade-pitch and blade-mass imbalances) and tower model (structural tower damping coefficient) adjustments. These calibration studies were conducted based on relatively simple calibration load cases (wave only/wind only). The agreement between the final FAST model and experimental measurements is then assessed based on more-complex combined wind and wave validation cases.

17 WIND ENERGY↗

A Case Study in the Application of TSUNAMI-3D - Part 1, Multigroup

The use of the sensitivity and uncertainty tool suite within SCALE, known as the TSUNAMI suite, has grown following its initial introduction more than a decade ago. Proper use of these tools provides a more complete understanding of system responses to perturbations, especially in the area of nuclear cross section uncertainties. Recent advances within TSUNAMI have added generalized perturbation theory to the k{sub eff} sensitivity capability that was included in TSUNAMI originally. The generation of sensitivity data is encouraged in the review process for new critical experiment requests sponsored by the US Department of Energy (DOE) Nuclear Criticality Safety Program (NCSP) to demonstrate that the proposed experiment will satisfy the identified data need. Many individuals participate in this process, but many analysts have not received proper training in the use of the TSUNAMI tools. The adjoint perturbation theory used to calculate sensitivities is not typically included in nuclear engineering curricula, leaving inexperienced engineers particularly at risk for incorrect use of the tools. The first step in the use of the TSUNAMI tools is the generation of a sensitivity data file (SDF), which contains all of the energy-dependent sensitivity data generated for a model. Most often, the SDF is generated from a three-dimensional (3D) model using either the KENO V.a or KENO-VI code within the TSUNAMI-3D sequence. The sensitivity data generated in TSUNAMI-3D must be accurate for correct quantification of system similarity or any other use of the sensitivity data. The sensitivities calculated by TSUNAMI can be affected by many of the input parameters, cross section processing models, and geometry modeling techniques used within the TSUNAMI-3D input. Fortunately, the total sensitivity of the most important nuclides can be confirmed simply by using direct perturbation (DP) calculations. Confirmation of the total sensitivity of these important nuclides provides confidence that the flux and importance function calculated within the TSUNAMI sequence will yield accurate sensitivities for all nuclides, reactions, and energies of interest. This process is essentially identical for the multigroup (MG) methods and the continuous-energy (CE) methods introduced in SCALE 6.2. This paper discusses the use of DP calculations and provides a case study to confirm that accurate sensitivities are generated by TSUNAMI-3D for a particular benchmark experiment. A companion paper provides a similar case study applying the CE TSUNAMI capability to the same critical experiment. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

A Case Study in the Application of TSUNAMI-3D - Part 2, Continuous Energy

The use of the sensitivity and uncertainty tool suite within SCALE, which is known as the TSUNAMI suite, has grown following its initial introduction more than a decade ago. Proper use of this tool provides a more complete understanding of system responses to perturbations, especially in the area of nuclear cross section uncertainties. Recent advances within TSUNAMI have added generalized perturbation theory to the k{sub eff} sensitivity capability that was included in TSUNAMI originally. The sensitivities can also be used to quantify the similarity of two systems. As an example, calculated sensitivities can be combined with cross section uncertainties to determine the similarity index ck. The generation of sensitivity data is encouraged in the review process for new critical experiment requests sponsored by the US Department of Energy (DOE) Nuclear Criticality Safety Program (NCSP) to demonstrate that the proposed experiment will satisfy the identified data need. Many analysts participate in this process, but many have not received proper training in the use of the TSUNAMI tools. The adjoint perturbation theory used to calculate sensitivities is not typically included in nuclear engineering curricula, leaving inexperienced engineers particularly at risk for incorrect use of the tools. The first step in the use of the TSUNAMI tools is the generation of a sensitivity data file (SDF), which contains all of the energy-dependent sensitivity data generated for a model. Most often, the SDF is generated from a three-dimensional (3D) model using either the KENO V.a or KENO-VI code within the TSUNAMI-3D sequence. The sensitivity data generated in TSUNAMI-3D must be accurate for correct quantification of system similarity or any other use of the sensitivity data. The sensitivities calculated by TSUNAMI can be affected by many of the input parameters, cross section processing models, and geometry modeling techniques used within the TSUNAMI-3D input. Fortunately, the total sensitivity of the most important nuclides can be confirmed simply by using direct perturbation (DP) calculations. Confirmation of the total sensitivity of these important nuclides provides confidence that the flux and importance function calculated within the TSUNAMI sequence will yield accurate sensitivities for all nuclides, reactions, and energies of interest. This process is essentially identical for multigroup (MG) and continuous-energy (CE) methods introduced in SCALE 6.2. This paper discusses the use of direct perturbation calculations and provides a case study in the use of DP calculations to confirm accurate sensitivities generated by the CE CLUTCH methods in TSUNAMI-3D for a particular benchmark experiment. A companion paper provides a similar case study applying the MG TSUNAMI capability to the same critical experiment. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

The interpenetration polymer network in a cement paste–waterborne epoxy system

The formation of the interpenetrating polymer network (IPN) structure within the cement-polymer system has been revealed by experiments from 2 dimensional to 3-dimensional scales. However, the microstructure design and performance prediction of IPN as a function of specific C-S-H/polymer components or ingredients' parameters e.g. water to cement ratios (w/c), polymer to cement ratios (p/c), monomer components, degree of polymerization (DP), etc. is by far not available. Here we developed a mesoscale model for IPN visualization based on the Flory-Huggins interaction theory which was applied to cement science for the first time. All the ingredients in the micro-structure were considered as soluble beads with rational sizes based on their properties obtained by molecular dynamic methods. The interaction parameters of each bead were then determined based on their element ratios and chemical backbones. The model was validated with the waterborne epoxy-cement material (WECM) in which a novel waterborne epoxy resin (WEP) was prepared and impregnated. The verification results on the 2D-3D scale show that the developed model predicts the WECM's IPN structures by rule and line concerning DP, w/c, and p/c in the mixture. The C-S-H beads were progressively scaled in size which alters the C-S-H texture to have completely different dissolution characteristics. Beads of diameter ~6 Å are more unstable and soluble which enable them to form a continuous phase in water or a composite structure with WEP. In contrast, beads with diameters larger than 10 Å have different properties with stronger nucleation effects. The results also suggest the impregnation content of WEP in cement-based material should be limited to 10% vol. to prevent the polymer IPN from decomposing into discrete clusters. The application of Flory-Huggins theory in cement-based composites demonstrates great potential in performance prediction and microstructure design.

36 MATERIALS SCIENCE↗

Enhancing the connection between computation and experiments in electrocatalysis

Combining computational and experimental methods is a powerful approach to understand the variables that govern catalyst performance and ultimately design improved materials. However, the effectiveness of this approach rests on the strength of the relationships between calculated parameters and experimental measurements. These relationships are complicated by the intricacy and dynamic behaviour of catalytic active sites, and by the non-trivial relationship between calculated reaction energetics and observed rates. In this Perspective, we highlight opportunities to enhance the connection between computation and experiment in electrocatalysis. These include measuring the intrinsic kinetic behaviour of catalysts, creating precise models for the active site and its environment, and forming clear relationships between calculated reaction energetics and observed rates. As experimental and computational methods continue to become more powerful, clear connections between the two will maximize their utility to guide the design of efficient and selective electrocatalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The STRong lensing Insights into the Dark Energy Survey (STRIDES) 2016 follow-up campaign – I. Overview and classification of candidates selected by two techniques

Here, the primary goals of the STRong lensing Insights into the Dark Energy Survey (STRIDES) collaboration are to measure the dark energy equation of state parameter and the free streaming length of dark matter. To this aim, STRIDES is discovering strongly lensed quasars in the imaging data of the Dark Energy Survey and following them up to measure time delays, high resolution imaging, and spectroscopy sufficient to construct accurate lens models. In this paper, we first present forecasts for STRIDES. Then, we describe the STRIDES classification scheme, and give an overview of the Fall 2016 follow-up campaign. We continue by detailing the results of two selection methods, the Outlier Selection Technique and a morphological algorithm, and presenting lens models of a system, which could possibly be a lensed quasar in an unusual configuration. We conclude with the summary statistics of the Fall 2016 campaign. Including searches presented in companion papers (Anguita et al.; Ostrovski et al.), STRIDES followed up 117 targets identifying 7 new strongly lensed systems, and 7 nearly identical quasars (NIQs), which could be confirmed as lenses by the detection of the lens galaxy. 76 candidates were rejected and 27 remain otherwise inconclusive, for a success rate in the range 6-35\%. This rate is comparable to that of previous searches like SQLS even though the parent dataset of STRIDES is purely photometric and our selection of candidates cannot rely on spectroscopic information.

79 ASTRONOMY AND ASTROPHYSICS↗

Overview of a Methodology for Calculating the A Priori Scan Minimum Detectable Concentration for Post-Processed Radiological Surveys (Final Report) (Rev.1)

Increased continuous data collection using automated data loggers and autonomous radiological survey devices or vehicles has introduced a need for corresponding guidance and statistical techniques for data that are collected without surveyor vigilance. This report presents a method for calculating the a priori scan minimum detectable concentrations (MDCs) for surveys performed without vigilance similar to methods described in the Multi-Agency Radiation Survey and Site Investigation Manual, NUREG-1507, and NUREG/CR-6364. A priori scan MDCs are calculated during survey planning to ensure that survey parameters (e.g., scanning speed, scanning altitude, detector geometry) will lead to collecting data in which potentially contaminated areas can be detected when data are processed after the survey, within acceptable statistical error probabilities.

54 ENVIRONMENTAL SCIENCES↗

Selected Diagnostics for Microgravity Combustion Science

The evolution of our understanding of combustion phenomena occurring under reduced gravity conditions poses a continuing demand for diagnostic tools of increased sophistication. Existing methods have become insufficient to keep pace with emerging refinements in the underlying theories and predictive models. The coupling of physical mechanisms inherent in combustion systems mandates the simultaneous determination of numerous thermophysical quantities, principally temperature, velocity, and species concentrations. Observed differences attributable to variations in experimental configuration, fuels and diluents, and initial conditions enhance the difficulty of developing diagnostic methods suitable for the acquisition of the required data over the desired range of experimental parameters. Efforts to provide for ongoing diagnostic development supporting microgravity combustion science experiments are conducted within the Microgravity Science Division at the NASA-Lewis Research Center. The following describes recent results from several diagnostic development efforts conducted under this project.

Greenberg, Paul S.↗

Development of Wireless Subsurface Microsensors for Health Monitoring of Thermal Protection Systems

Low cost access to space is a primary goal for both NASA and the U.S. aerospace industry. Integrated subsystem health diagnostics is an area where major improvements have been identified for potential implementation into the design of new reusable launch vehicles (RLVS) in order to reduce life cycle costs, increase safety margins and improve mission reliability. A number of efforts are underway to use existing and emerging technologies to establish new methods for vehicle health monitoring on operational vehicles as well as X-vehicles. This paper summarizes a joint effort between several NASA centers and industry partners to develop rapid wireless diagnostic tools for failure management and long-term TPS performance monitoring of thermal protection systems (TPS) on future RLVS. An embedded wireless microsensor suite is being designed to allow rapid subsurface TPS health monitoring and damage assessment. This sensor suite will consist of both passive overlimit sensors and sensors for continuous parameter monitoring in flight. The on-board diagnostic system can be used to radio in maintenance requirements before landing and the data could also be used to assist in design validation for X-vehicles. For a 3rd generation vehicle, wireless diagnostics should be at a stage of technical development that will allow use for intelligent feedback systems for guidance and navigation control applications and can also serve as feedback for TPS that can intelligently adapt to its environment.

Pallix, Joan↗