Search NASA⌕ Search

SEARCH · Search NASA

Results for “rotating flows”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42
All sourcesNASA NTRSDOE OSTI
NASA NTRS2007

Numerical Technique for Analyzing Rotating Rake Mode Measurements in a Duct With Passive Treatment and Shear Flow

A technique is presented for the analysis of measured data obtained from a rotating microphone rake system. The system is designed to measure the interaction modes of ducted fans. A Fourier analysis of the data from the rotating system results in a set of circumferential mode levels at each radial location of a microphone inside the duct. Radial basis functions are then least-squares fit to this data to obtain the radial mode amplitudes. For ducts with soft walls and mean flow, the radial basis functions must be numerically computed. The linear companion matrix method is used to obtain both the eigenvalues of interest, without an initial guess, and the radial basis functions. The governing equations allow for the mean flow to have a boundary layer at the wall. In addition, a nonlinear least-squares method is used to adjust the wall impedance to best fit the data in an attempt to use the rotating system as an in-duct wall impedance measurement tool. Simulated and measured data are used to show the effects of wall impedance and mean flow on the computed results.

Dahl, Milo D.↗
NASA NTRS1990

A synchronous strobed laser light sheet for helicopter model rotor flow visualization

A synchronous, strobed laser light sheet has been developed for use in flow visualization of a helicopter rotor model. The light sheet strobe circuit included selectable blade position, strobe duration, and multiple pulses per revolution for rotors having 2 to 9 blades. The flow was seeded with propylene glycol. Between runs, a calibration grid board was placed in the plane of the laser sheet and recorded with the video camera at the position used to record the flow field. A slip-sync mode permitted slow motion visualization of the flow field over complete rotations of the rotor. The system was used to make two-dimensional flow field cuts of a four-bladed rotor operating at advance ratio of 0.37 at wind tunnel speeds up to 79.25 meters per second (260 feet per second).

Leighty, Bradley D.↗
NASA NTRS1984

Four New Capabilities in NASTRAN for Dynamic and Aeroelastic Analyses of Rotating Cyclic Structures

Static aerothermoelastic design/analysis of axial-flow compressors, modal flutter analysis of axial-flow turbomachines, forced vibration analysis of rotating cyclic structures and modal flutter analysis of advanced turbopropellers with highly swept blades are four new capabilities developed and implemented in NASTRAN Level 17.7. The contents, applicability and usefulness of these capabilities which were developed and documented under the sponsorship of NASA's Lewis Research Center are discussed. Overall flowcharts and selected examples are presented.

Elchuri, V.↗
NASA NTRS1981

On the magnetic viscosity in Keplerian accretion disks

The paper develops a model for the anomalous viscosity in accretion disks based on the hypothesis that the hydrodynamic turbulence within the disk takes the form of spatially localized magnetic flux cells. The local shear flow due to Keplerian differential rotation distorts the flux cell topology, converting shear flow energy into magnetic energy. In the radial diffusion approximation, the kinematic viscosity is estimated from the radial displacement and is shown to maximize at flux cell scale lengths for which the shear flow stopping and reconnection times are equal.

Coroniti, F. V.↗
NASA NTRS1974

Iterative solution of transonic flows over airfoils and wings, including flows at Mach 1

A new method of calculating transonic flows based on a 'rotated' difference scheme is described. It is suitable for the calculation of both two- and three-dimensional flows without restriction on the speed at infinity and is well adapted to computer use. The Murman procedure is modified to eliminate any assumptions about the direction of flow when constructing the difference scheme. The proper directional property is obtained by rotating the difference scheme to conform with the local stream direction. In the hyperbolic region retarded difference formulas are used for all contributions to the streamwise second derivative, producing a correctly oriented positive artificial viscosity. In the absence of a simple implicit scheme in the hyperbolic and elliptic regions, the concept of iterations as steps in artificial time is introduced. Computer testing of this procedure provides numerical confirmation of the existence and uniqueness of weak solutions of the potential equation when a suitable entropy inequality is enforced.

Jameson, A.↗
DOE OSTI2021

Numerical investigation of mass flow rate effects on multiplicity of detonation waves within a H 2 /Air rotating detonation combustor

This paper presents results from numerical simulations of a non-premixed hydrogen-air rotating detonation combustor with radial injection. The fuel and air mass flow rate are varied in order to hold a unity global equivalence ratio. The calculations show that multiple detonation waves co-exist when the mass flow rate is increased. Conditional statistics of the detonation structure and combustion processes suggest similarities across co-existing waves. Quantification of the injection response to the rotation of a detonation indicates that at higher flow rate the refill time is short enough to allow for a quick and well mixed composition prior to the new front passage. Details of the combustion characteristics are analyzed. Finally, the results elucidate the correlation between initial injection conditions and detonation multiplicity on the overall physics within the combustor.

08 HYDROGEN↗
NASA NTRS1992

Effects of curvature and rotation on turbulence in the NASA low-speed centrifugal compressor impeller

The flow in the NASA Low-Speed Impeller is affected by both curvature and rotation. The flow curves due to the following: (1) geometric curvature, e.g. the curvature of the hub and shroud profiles in the meridional plane and the curvature of the backswept impeller blades; and (2) secondary flow vortices, e.g. the tip leakage vortex. Changes in the turbulence and effective turbulent viscosity in the impeller are investigated. The effects of these changes on three-dimensional flow development are discussed. Two predictions of the flow in the impeller, one with, and one without modification to the turbulent viscosity due to rotation and curvature, are compared. Some experimental and theoretical background for the modified mixing length model of turbulent viscosity will also be presented.

Moore, Joan G.↗
NASA NTRS1981

Modeling of the float zone process

The interaction of heat, mass, and momentum transport in the floating zone method for growing single crystals from the melt is examined. Methods for detailed numerical simulation of the transport phenomena in a floating zone are developed. Results of the calculations are combined with experiments to determine the effects of solidification induced, surface tension driven, and buoyancy driven convection in establishing dopant redistribution in the melt and the roles of heat transfer in crystal and melt and melt/solid interface shape in determining crystal quality. State of the art finite element techniques were developed for calculating the influence of natural convection in the melt on the shape of a melt/crystal interface and dopant segregation in the crystal. These techniques are demonstrated for solidification by the Bridgman technique. Numerical techniques are developed that calculate the shapes of both the melt/solid and melt/gas interfaces simultaneously with the thermal fields in melt and solid. Models for the fluid flows due to the rotation of the feed and crystal rods are completed and the effects of these flows on dopant segregation are studied, especially in the case of zones longer than can be achieved on Earth.

Brown, R. A.↗
NASA NTRS1981

Three-dimensional structures and turbulence closure of the wake developing in a wall shear layer

The turbulent wake interacting with the rotating wall shear layer is investigated analytically and numerically. The turbulent wakes of the rotating blades in a compressor which are interacting with the rotating hub-wall boundary layer are analyzed. A modified version of the closure model of the pressure-strain correlation term in the Reynolds stress transport equation is developed to predict the effect of rotation, which is appreciable for the present flow because the thick hub-wall boundary layer is interacting with the rotor wake. It is noted that the Poisson type equation for the pressure-strain correlation has an extra rotation term when the entire flow field is rotating. This extra rotation term is modeled to accommodate the effect of rotation. In addition, the standard correction for the wall effect is incorporated for the utilized Reynolds stress closure model. The rotation-modified Reynolds stress closure model is used to predict the present flow, and the predictions are compared with the experimental data. The experimental data reveal that the characteristics of the three-dimensional turbulent wake interacting with the wall shear layer are considerably altered by the effects of the wall and the rotation. These features are predicted with good accuracy by the turbulence closure model developed.

Hah, C.↗
DOE OSTI2023

Two-phase separator device for removing condensate or particulate from a gas stream

This disclosure provides a two-phase separator device for separating condensate or particulate from a gas stream. In some implementations, the separator device removes water from air and may operate under micro-gravity conditions. The gas stream flows through the two-phase separator device and passes through a rotatable vane assembly along a flow path without being redirected in another flow path. Condensate or particulate in the gas stream is impacted by a plurality of vanes of the rotatable vane assembly, and the condensate is captured by features formed within the plurality of vanes. The captured condensate is accelerated radially outwardly along the each of the plurality of vanes towards a sloped inner wall, and further moved along the sloped inner wall in a direction against the flow path of the gas stream during rotation.

Cognata, Thomas↗
NASA NTRS1986

Analytical and numerical studies of the thermocapillary flow in a uniformly floating zone

The microgravity environment of an orbiting vehicle permits crystal growth experiments in the presence of greatly reduced buoyant convection in the liquid melt. Crystals grown in ground-based laboratories do not achieve their potential properties because of dopant variations caused by flow in the melt. The floating zone crystal growing system is widely used to produce crystals of silicon and other materials. However, in this system the temperature gradient on the free sidewall surface of the melt is the source of a thermocapillary flow which does not disappear in the low-gravity environment. The idea of using a uniform rotation of the floating zone system to confine the thermocapillary flow to the melt sidewall leaving the interior of the melt passive is examined. A cylinder of fluid with an axial temperature gradient imposed on the cylindrical sidewall is considered. A half zone and the linearized, axisymmetric flow in the absence of crystal growth is examined. Rotation is found to confine the linear thermocapillary flow. A simplified model is extended to a full zone and both linear and nonlinear thermocapillary flows are studied theoretically. Analytical and numerical methods are used for the linear flows and numerical methods for the nonlinear flows. It was found that the linear flows in the full zone have more complicated and thicker boundary layer structures than in the half zone, and that these flows are also confined by the rotation. However, for the simplified model considered and for realistic values for silicon, the thermocapillary flow is not linear. The fully nonlinear flow is strong and unsteady (a weak oscillation is present) and it penetrates the interior. Some non-rotating flow results are also presented. Since silicon as a large value of thermal conductivity, one would expect the temperature fields to be determined by conduction alone. This is true for the linear and weakly nonlinear flows, but for the stronger nonlinear flow the results show that temperature advection is also important. Uniform rotation may still be a means of confining the flow and the results obtained define the procedure to be used to examine this hypothesis.

Fowlis, W. W.↗
DOE OSTI2026

Global Non-axisymmetric Hall Instabilities in a Rotating Plasma

Non-axisymmetric, flow-driven instabilities in the incompressible Hall-MHD model are studied in a differentially rotating cylindrical plasma. It is found that, in the Hall-MHD regime, both whistler waves and ion-cyclotron waves can extract energy from the flow shear, resulting in two distinct branches of global instability. The non-axisymmetric whistler modes grow significantly faster than non-axisymmetric, ideal MHD modes. A discussion of the global whistler instability mechanism is presented in the large-ion-skin-depth, “electron-MHD” limit. When the magnetic field is azimuthal, a subset of the whistler modes having zero axial wave number are uncovered to be destabilized by the “corotation amplifier” mechanism. It is observed that the effect of the Hall term on the non-axisymmetric modes can be appreciable when d i is on the order of a few percent of the width of the cylindrical annulus. Distinct global modes emerge in the strong Hall-MHD regime at significantly stronger magnetic fields than those required for unstable global MHD modes, as the Hall effect weakens the stabilizing “field-line bending” by decoupling ion motion from the magnetic field. These global non-axisymmetric modes may play an important role in weakly ionized accretion disks.

Alfven waves↗
NASA NTRS1994

Magnetically driven relativistic jets and winds: Exact solutions

We present self-consistent solutions of the full set of ideal MHD equations which describe steady-state relativistic cold outflows from thin accretion disks. The magnetic field forms a spiral which is anchored in the disk, rotates with it, and accelerates the flow out of the disk plane. The collimation at large distances depends on the total amount of electric current that flows along the jet. We considered various distributions of electric current and derived the result that in straight jets which extend to infinite distances, a strong electric current flows along their axis of symmetry. The asymptotic flow velocities are of the order of the initial rotational velocity at the base of the flow (a few tenths of the speed of light). The solutions are applied to both galactic (small-scale) and extragalactic (large-scale) jets.

Contopoulos, J.↗
NASA NTRS1959

Investigation on the use of a Freely Rotating Rotor at the Cowl Face of a Supersonic Conical Inlet to Reduce Inlet Flow Distortion

An investigation has been made on the use of a freely rotating rotor at the cowl face of a supersonic conical diffuser to determine its effectiveness in reducing inlet flow distortion and the penalty in terms of total-pressure loss imposed by such a device when distortions are negligible. Tests were made with a rotor having an inlet tip diameter of 2.18 inches and a ratio of hub radius to tip radius of 0.52, in conjunction with a conical inlet having a 25 deg semi-vertex cone angle, at a Mach number of 2.1 over an angle-of-attack range of 0 deg to 8 deg. A simplified analysis showing that a supersonic, freely rotating rotor with maximum solidity for noninterference between blades will operate in an undistorted flow with a total-pressure defect of 1 percent or less was experimentally verified. Overall total-pressure distortions of 0.1 to 0.4 and Mach number distortions of 0.4 to 1.4, obtained at 4 deg to 8 deg angle of attack, were reduced about 30 percent and 23 percent, respectively, because of the presence of the rotor, with no measurable total-pressure loss. The rotor increased the peak total-pressure recovery at the simulated combustion chamber 1 1/2 and 3 1/2 percent at 6 deg and 8 deg angles of attack, respectively. This increase is attributed to lower diffusion duct losses as a consequence of a more uniform flow created by the rotor.

Goldberg, Theodore J.↗
NASA NTRS1975

Minimization of jet and core noise of a turbojet engine by swirling the exhaust flow

A noise abating improvement for jet engines has been investigated and demonstrated using a full scale turbojet engine which provided the means for significant reductions in jet and core noise with minimal thrust loss. This was accomplished by controlled solid body rotation (swirling) of the flow in the nozzle and jet exhaust. Relatively moderate angles of solid body rotation in the presence of temperature, density, pressure, and velocity gradients were utilized. Of great interest was the finding that significant reductions of sound pressure levels and sound power were obtained with only a small percentage of the total primary mass flow swirling at the exit of the nozzle. Therefore, tradeoffs between noise reduction and engine performance can be optimized to satisfy aircraft performance and federal noise standards with minimal wasted rotational kinetic energy.

Schwartz, I. R.↗