SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Neural networks tend to fall into two general categories: (1) software simulations, or (2) custom hardware that must be trained. The scope of this project is the merger of these two classifications into a system whereby a software model of a network is trained to perform a specific task and the results used to synthesize a standard cell realization of the network using automated tools.
Video-based motion analysis systems are widely employed to study human movement, using computers to capture, store, process, and analyze video data. This data can be collected in any environment where cameras can be located. One of the NASA facilities where human performance research is conducted is the Weightless Environment Training Facility (WETF), a pool of water which simulates zero-gravity with neutral buoyance. Underwater video collection in the WETF poses some unique problems. This project evaluates the error caused by the lens distortion of the WETF cameras. A grid of points of known dimensions was constructed and videotaped using a video vault underwater system. Recorded images were played back on a VCR and a personal computer grabbed and stored the images on disk. These images were then digitized to give calculated coordinates for the grid points. Errors were calculated as the distance from the known coordinates of the points to the calculated coordinates. It was demonstrated that errors from lens distortion could be as high as 8 percent. By avoiding the outermost regions of a wide-angle lens, the error can be kept smaller.
A virtual reality (VR) applications program has been under development at the Marshall Space Flight Center (MSFC) since 1989. The objectives of the MSFC VR Applications Program are to develop, assess, validate, and utilize VR in hardware development, operations development and support, mission operations training and science training. Before VR can be used with confidence in a particular application, VR must be validated for that class of applications. For that reason, specific validation studies for selected classes of applications have been proposed and are currently underway. These include macro-ergonomic 'control room class' design analysis, Spacelab stowage reconfiguration training, a full-body microgravity functional reach simulator, a gross anatomy teaching simulator, and micro-ergonomic design analysis. This paper describes the MSFC VR Applications Program and the validation studies.
Firefighting trainees conduct fire control exercises using a prototype simulator known as the Emergency Management Computer Aided Training System (EMCAT). Developed by Marshall Space Flight Center (MFS) in response to a request from the Huntsville (AL) Fire Department, EMCAT enables a trainee to assume the role of fireground commander and make quick decisions on best use of his fire fighting personnel and equipment.
The NASA Space Medicine program is now developing plans for more extensive use of high-fidelity medical simulation systems. The use of simulation is seen as means to more effectively use the limited time available for astronaut medical training. Training systems should be adaptable for use in a variety of training environments, including classrooms or laboratories, space vehicle mockups, analog environments, and in microgravity. Modeling and simulation can also provide the space medicine development program a mechanism for evaluation of other medical technologies under operationally realistic conditions. Systems and procedures need preflight verification with ground-based testing. Traditionally, component testing has been accomplished, but practical means for "human in the loop" verification of patient care systems have been lacking. Medical modeling and simulation technology offer potential means to accomplish such validation work. Initial considerations in the development of functional requirements and design standards for simulation systems for space medicine are discussed.
The application of simulation technology to mission planning and rehearsal has enabled realistic overhead 2-D and immersive 3-D "fly-through" capabilities that can help better prepare tactical teams for conducting missions in unfamiliar locales. For aircrews, detailed terrain data can offer a preview of the relevant landmarks and hazards, and threat models can provide a comprehensive glimpse of potential hot zones and safety corridors. A further extension of the utility of such planning and rehearsal techniques would allow users to perform the radio communications planned for a mission; that is, the air-ground coordination that is critical to the success of missions such as close air support (CAS). Such practice opportunities, while valuable, are limited by the inescapable scarcity of complete mission teams to gather in space and time during planning and rehearsal cycles. Moreoever, using simulated comms with synthetic entities, despite the substantial training and cost benefits, remains an elusive objective. In this paper we report on a solution to this gap that incorporates "synthetic teammates" - intelligent software agents that can role-play entities in a mission scenario and that can communicate in spoken language with users. We employ a fielded mission planning and rehearsal tool so that our focus remains on the experimental objectives of the research rather than on developing a testbed from scratch. Use of this planning tool also helps to validate the approach in an operational system. The result is a demonstration of a mission rehearsal tool that allows aircrew users to not only fly the mission but also practice the verbal communications with air control agencies and tactical controllers on the ground. This work will be presented in a CAS mission planning example but has broad applicability across weapons systems, missions and tactical force compositions.
The experiments described in this paper are part of a larger joint MIT/NASA research effort and focus on the development of a methodology for designing and evaluating integrated interfaces for highly dexterous and multifunctional telerobot. Specifically, a telerobotic workstation is being designed for an Extravehicular Activity (EVA) anthropomorphic space station telerobot called Robonaut. Previous researchers have designed telerobotic workstations based upon performance of discrete subsets of tasks (for example, peg-in-hole, tracking, etc.) without regard for transitions that operators go through between tasks performed sequentially in the context of larger integrated tasks. The experiments presented here took an integrated approach to describing teleoperator performance and assessed how subjects operating a full-immersion telerobot perform during fine position and gross position tasks. In addition, a Robonaut simulation was also developed as part of this research effort, and experimentally tested against Robonaut itself to determine its utility. Results show that subject performance of teleoperated tasks using both Robonaut and the simulation are virtually identical, with no significant difference between the two. These results indicate that the simulation can be utilized as both a Robonaut training tool, and as a powerful design platform for telepresence displays and aids.
The NASA Space Medicine program is now developing plans for more extensive use of high-fidelity medical Simulation systems. The use of simulation is seen as means to more effectively use the limited time available for astronaut medical training. Training systems should be adaptable for use in a variety of training environments, including classrooms or laboratories, space vehicle mockups, analog environments, and in microgravity. Modeling and simulation can also provide the space medicine development program a mechanism for evaluation of other medical technologies under operationally realistic conditions. Systems and procedures need preflight verification with ground-based testing. Traditionally, component testing has been accomplished, but practical means for "human in the loop" verification of patient care systems have been lacking. Medical modeling and simulation technology offer potential means to accomplish such validation work. Initial considerations in the development of functional requirements and design standards for simulation systems for space medicine are discussed.
An algorithm for computationally lightweight simulation of automated air traffic control (ATC) at a busy airport has been derived. The algorithm is expected to serve as the basis for development of software that would be incorporated into flight-simulator software, the ATC component of which is not yet capable of handling realistic airport loads. Software based on this algorithm could also be incorporated into other computer programs that simulate a variety of scenarios for purposes of training or amusement.
We have developed a new aerosol retrieval technique based on combing high-resolution A band spectra with lidar profiles. Our goal is the development of a technique to retrieve aerosol absorption, one of the critical parameters affecting the global radiation budget and one which is currently poorly constrained by satellite measurements. Our approach relies on two key factors: 1) the use of high spectral resolution (17,000:1) measurements which resolve the A-band line structure, and 2) the use of co-located lidar profile measurements to constrain the vertical distribution of scatterers in the forward model. The algorithm has been developed to be applied to observations from the CALIPSO and OCO-2 satellites, flying in formation as part of the A-train constellation. We describe the approach and present simulated retrievals to illustrate performance potential.
The BioSentinel mission was launched in 2022 aboard the SLS launch vehicle as part of the Artemis-I campaign and continues mission operations into 2024. The 6U CubeSat has been characterizing deep space radiation at large distances from Earth. This presentation gives a status of the mission performance to date, as well as some of the lessons learned from project. BioSentinel has achieved unprecedented performance as an SLS secondary payload due to preparation, planning, and a robust design. Pre-launch antenna and interface testing with both DSN and ESA confirmed command and data pathways and allowed for operational flexibility in the critical early hours post-deployment. Mission Operations simulations prior to launch identified potential risks and trained operators to respond in flight, preparing the team to react quickly and successfully to detumble the spacecraft and enter a power-positive state. The spacecraft would not have survived without the inclusion of the trailblazing 3D-printed composite cold gas propulsion system. The non-standard tank geometry enabled efficient use of the limited space available in the CubeSat form factor as well as the capability to detumble the spacecraft and manage momentum for extended mission durations, while providing sufficient margin to execute potential delta-V maneuvers. Following the conclusion of the primary science mission, the Linear Energy Transfer (LET) Spectrometer has continued to collect solar and galactic radiation data from its unique location in heliocentric orbit. The free space dataset offered by the BioSentinel LET is a valuable source of data for both model validation and future mission planning. As the spacecraft travels farther from Earth it is poised to provide longitudinally distributed measurements of solar particle events during solar maximum. NASA Ames led development of the BioSentinel spacecraft to operate for long durations in deep space. The novel subsystems and COTS components that comprise the BioSentinel bus can serve as a template for future deep space missions, while the lessons the team has learned from well over a year of continuous operations will enable improved performance in the generation of deep space CubeSat missions.
The all-electric X-57 Mod III aircraft was designed to demonstrate wingtip propulsion drag reduction benefits on a high-aspect-ratio wing. The X-57 Mod IV aircraft was designed to expand on the Mod III version and demonstrate the benefits of distributed electric propulsion. This paper discusses the development of theall-electricX-57 Mod III and Mod IV fixed-base pilot-in-the-loop nonlinear simulator. The paper describes the model development and the simulator cockpit construction for uses such as flight training and flying qualities analysis. Results from a stability and flying qualities analysis for both Mod III and Mod IV are presented. These results predict that both Mod III and Mod IV are stable throughout their flight envelopes. Mod III is predicted to have satisfactory flying qualities while Mod IV is predicted to have areas of adequate flying qualities.
Air transportation is undergoing a rapid evolution globally with the introduction of Advanced Air Mobility (AAM) and with it comes novel challenges and opportunities for transforming aviation. As AAM operations introduce increasing heterogeneity in vehicle capabilities and density, increased levels of automation are likely necessary to achieve operational safety and efficiency goals. This paper focuses on one example where increased automation has been suggested. Autonomous operations will need contingency management systems that can monitor evolving risk across a span of interrelated (or interdependent) hazards and, if necessary, execute appropriate control interventions via supervised or automated decision making. Accommodating this complex environment may require automated functions (autonomy) that apply artificial intelligence (AI) techniques that can adapt and respond to a quickly changing environment. This paper explores the use of Deep Reinforcement Learning (DRL) which has shown promising performance in complex and high-dimensional environments where the objective can be constructed as a sequential decision-making problem. An extension of a prior formulation of the contingency management problem as a Markov Decision Process (MDP) is presented and uses a DRL framework to train agents that mitigate hazards present in the simulation environment. A comparison of these learning-based agents and classical techniques is presented in terms of their performance, verification difficulties, and development process.
Air transportation is undergoing a rapid evolution globally with the introduction of Advanced Air Mobility (AAM) and with it comes novel challenges and opportunities for transforming aviation. As AAM operations introduce increasing heterogeneity in vehicle capabilities and density, increased levels of automation are likely necessary to achieve operational safety and efficiency goals. This paper focuses on one example where increased automation has been suggested. Autonomous operations will need contingency management systems that can monitor evolving risk across a span of interrelated (or interdependent) hazards and, if necessary, execute appropriate control interventions via supervised or automated decision making. Accommodating this complex environment may require automated functions (autonomy) that apply artificial intelligence (AI) techniques that can adapt and respond to a quickly changing environment. This paper explores the use of Deep Reinforcement Learning (DRL) which has shown promising performance in complex and high-dimensional environments where the objective can be constructed as a sequential decision-making problem. An extension of a prior formulation of the contingency management problem as a Markov Decision Process (MDP) is presented and uses a DRL framework to train agents that mitigate hazards present in the simulation environment. A comparison of these learning-based agents and classical techniques is presented in terms of their performance, verification difficulties, and development process.
In preparation for future exploration missions, NASA seeks the ability to simulate partial-gravity operations for use in ground-based research, crew training, and engineering design evaluations. The Active Response Gravity Offload System (ARGOS) at the Johnson Space Center (JSC) is designed to simulate reduced gravity environments, such as lunar, Martian, or microgravity, using a robotic system similar to an overhead bridge crane. ARGOS continuously offloads a portion of a suited human’s weight during all dynamic motions within the test facility, which can include basic functional movements such as walking, running, and jumping, as well as a wide range of planetary surface activities. This system will be used as part of a metabolic-rate task characterization study to determine the workload associated with partial-gravity extravehicular activity (EVA). Pilot testing was conducted using the MKIII prototype planetary space suit and two gimbal designs to determine the ability of the ARGOS test environment to simulate planetary EVA operations. This paper will describe the lessons learned from the feasibility testing, simulation-environment mockup design, and the results from the pilot tests and their influence into the final study design. Being able to effectively simulate partial-gravity environments and characterize the performance of crewmembers will have an impact on multiple domains including suit design, task design, thermal models, and life-support-system capacity verification plans, among others.
A flexible, hierarchical tool chain that is being applied to NASA’s Space Launch System (SLS) for critical dynamics phenomena is described. This tool chain, called CLVTOPS, is used to investigate lateral liftoff movement of the vehicle as it departs and clears the mobile launch tower and separation of the two solid rocket boosters without collision with the core stage and payload. The toolset’s architecture was configured to take advantage of a modern software-engineering approach for maximum flexibility and utilization of open-source simulations and associated tools. As opposed to a “monolithic” approach, scripting languages were used to “bind” together a tool chain to configure and organize input data, execute and produce analysis results, and post-process these results to facilitate a rapid iterative analysis process to quickly address issues and pursue alternatives with emphasis on analysis automation. Key capabilities in the tool chain include processing and mining of very large data sets, a wide range of graphical depictions, and high-fidelity, physics-based simulations. The paper begins with a problem description and the motivation for liftoff and separation dynamics analysis followed by a historical survey of dynamics analyses for previous NASA human-rated launch vehicles. Details of the tool chain and its components are then introduced divided, first, into description of the scripting language architecture used to “bind” the simulation tools, programs, and scripts together and, second, the physics models and simulations. Representative analyses and data products are shown for liftoff and booster separation dynamics that provide in-depth insight to the tool chain’s capabilities. Supporting activities such as simulation tool chain verification, version archiving and data management, and training are addressed. The paper concludes with case examples on how the tool chain can be tailored to related aerospace dynamics analyses, both large and small. These patterns and techniques for SLS dynamics tool construction can be applied for other aerospace simulations.
Recent advances in the development of machine learning (ML) algorithms have enabled the creation of predictive models that can improve decision making, decrease computational cost, and improve efficiency in a variety of fields. As an organization begins to develop and implement such models, the data used in the training, validation, and testing of ML models, the model parameters, and the use cases or limitations of the models must be properly stored to ensure models are both fully traceable and used correctly. In the context of predicting material behavior, advances in computationally intense, physics-based modeling of material behavior at various length scales and the emergence of Integrated Computational Materials Engineering (ICME) have driven the need for developing data-driven surrogate models of the physics-based simulation tools using ML techniques. Surrogate model development allows for accurate material behavior prediction at a fraction of the cost of its physics-based counterpart, allowing for multiscale simulations of real-world applications, further enabling the ability to design fit-for-purpose materials for a reasonable computational investment. However, training such models requires extensive data, and thus, effective data management is necessary to reach the full potential that ML can offer to material design and ICME. This paper proposes a generalized, robust schema that allows organizations to store both real (experimental) and virtual (simulation) data used to train ML models and the defining model parameters and architectures within the Granta MI Platform. The developed schema allows for various types of data inputs and outputs, including single point values, time-series data, and images that can be used in the prediction of material behavior, while following outlined best practices for effective data management. An effective schema for ML data and models can help prevent the recreation of virtual/real training data and surrogate models, help reduce the time to create new models similar to existing ones by offering a starting point in the hyperparameter determination stages, minimize resources devoted to verification and validation (V&V) and certification of models, and ensure that data and surrogate models are not misused due to full traceability of both the data and ML model. It also allows organizations access to models that have already been developed, such that they can be used in the design of new materials, enabling the overall goals of ICME.
Recent advances in the development of machine learning (ML) algorithms have enabled the creation of predictive models that can improve decision making, decrease computational cost, and improve efficiency in a variety of fields. As an organization begins to develop and implement such models, the data used in the training, validation, and testing of machine learning models, the model parameters, and the use cases or limitations of the models must be properly stored to ensure models are both fully traceable and used correctly. In the context of predicting material behavior, advances in computationally intense, physics-based, modeling of material behavior at various length scales, and the emergence of Integrated Computational Materials Engineering (ICME) have driven the need for developing data-driven surrogate models of the physics-based simulation tools using machine learning (ML) techniques. Surrogate model development allows for accurate material behavior prediction at a fraction of the cost of its physics-based counterpart, allowing for multiscale simulations of real-world applications, further enabling the ability to design fit-for-purpose materials for a reasonable computational investment. However, training such models requires extensive data, and thus effective data management is necessary to reach the full potential that ML can offer to material design and ICME. This paper proposes a generalized, robust schema that allows organizations to store both real (experimental) and virtual (simulation) data used to train machine learning models and the defining model parameters and architectures. The developed schema allows for various types of data inputs and outputs, including single point values, time-series data, and images that can be used in for various types of machine learning models while following outlined best practices for effective data management. An effective schema for machine learning data and models can help prevent the recreation of virtual/real training data and surrogate models, can help reduce the time to create new models similar to existing ones by offering a starting point in the hyperparameter determination stages, minimize resources devoted to verification and validation (V&V) and certification of models, and ensure that data and surrogate models are not misused due to full traceability of both the data and ML model. It also allows organizations access to models that have already been developed, such that they can be used in the design of new materials, enabling the overall goals of ICME.