Search NASA⌕ Search

SEARCH · Search NASA

Results for “Aerodynamic Performance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Model aerodynamic test results for two variable cycle engine coannular exhaust systems at simulated takeoff and cruise conditions. Comprehensive data report. Volume 2: Tabulated aeroynamic data book 1

Tabulated data from wind tunnel tests conducted to evaluate the aerodynamic performance of an advanced coannular exhaust nozzle for a future supersonic propulsion system are presented. Tests were conducted with two test configurations: (1) a short flap mechanism for fan stream control with an isentropic contoured flow splitter, and (2) an iris fan nozzle with a conical flow splitter. Both designs feature a translating primary plug and an auxiliary inlet ejector. Tests were conducted at takeoff and simulated cruise conditions. Data were acquired at Mach numbers of 0, 0.36, 0.9, and 2.0 for a wide range of nozzle operating conditions. At simulated supersonic cruise, both configurations demonstrated good performance, comparable to levels assumed in earlier advanced supersonic propulsion studies. However, at subsonic cruise, both configurations exhibited performance that was 6 to 7.5 percent less than the study assumptions. At takeoff conditions, the iris configuration performance approached the assumed levels, while the short flap design was 4 to 6 percent less. Data are provided through test run 25.

Nelson, D. P.↗
NASA NTRS1980

Results of a low-speed wind tunnel test of the MDC 2.2M supersonic cruise aircraft configuration

Results of a low speed test conducted in the Full Scale Tunnel at NASA Langley using an advanced supersonic cruise vehicle configuration are presented. These tests used a 10 percent scale model of a configuration that had demonstrated high aerodynamic performance at Mach 2.2 during a previous test program. The low speed model has leading and trailing edge flaps designed to improve low speed lift to drag ratios at high lift and includes devices for longitudinal and lateral/directional control. The results obtained during the low speed test program have shown that full span leading edge flaps are required for maximum performance. The amount of deflection of the leading edge flap must increase with C sub L to obtain the maximum benefit. Over 80 percent of full leading edge suction was obtained up to lift off C sub L's of 0.65. A mild pitch up occurred at about 6 deg angle of attack with and without the leading edge flap deflected. The pitch up is controllable with the horizontal tail. Spoilers were found to be preferable to spoiler/deflectors at low speeds. The vertical tail maintained effectiveness up to the highest angle of attack tested but the tail on directional stability deteriorated at high angles of attack. Lateral control was adequate for landing at 72 m/sec in a 15.4 m/sec crosswind.

Yip, L. P.↗
NASA NTRS1980

Supersonic wings with significant leading-edge thrust at cruise

Experimental/theoretical correlations are presented which show that significant levels of leading edge thrust are possible at supersonic speeds for certain planforms which match the theoretical thrust distribution potential with the supporting airfoil geometry. The analytical process employed spanwise distribution of both it and/or that component of full theoretical thrust which acts as vortex lift. Significantly improved aerodynamic performance in the moderate supersonic speed regime is indicated.

Robins, A. W.↗
NASA NTRS1981

Description of 0.186-scale model of high-speed duct of national transonic facility

The National Transonic Facility (NTF) is a pressurized cryogenic wind tunnel with a 2.5 m square test section. A 0.186-scale model of the NTF was used to simulate the aerodynamic performance of the components of the high-speed duct of the NTF. These components consist of a wide-angle diffuser, settling chamber, contraction section, test section, model support section, and high-speed diffuser. The geometry of the model tunnel, referred to as the diffuser flow apparatus is described, and some of its operating characteristics are presented.

Gentry, C. L., Jr.↗
NASA NTRS1981

Aircraft design using the National Transonic Facility

The utility of the cryogenic high Reynolds number test facility as a production tunnel is evaluated. Aerodynamic performance evaluation, numerical wing design verification, and high Reynolds number theoretical extensions are considered. A priority ranking of NTF uses from an airframe development viewpoint is presented.

Bonner, E.↗
NASA NTRS1981

Effects of blade-vane ratio and rotor-stator spacing of fan noise with forward velocity

A research fan stage was acoustically tested in an anechoic wind tunnel with a 41 m/sec tunnel flow. Two stator vane numbers giving cut-on and cut-off conditions were tested at three rotor-stator spacings ranging from about 0.5 to 2.0 rotor chords. These two stators were designed for similar aerodynamic performance. Hot film anemometer turbulence measurements were made at the leading edge of the stator for each spacing. The cut-off criterion strongly controlled the fundamental tone level at all spacings. The trends with spacing of the wake defect upwash component at the stator tip showed good agreement with the corresponding cut-on acoustic tone levels.

Woodward, R. P.↗
NASA NTRS1981

A full-scale wind tunnel investigation of a helicopter bearingless main rotor

A helicopter bearingless main rotor was tested. Areas of investigation included aeroelastic stability, aerodynamic performance, and rotor loads as a function of collective pitch setting, RPM, airspeed and shaft angle. The rotor/support system was tested with the wind tunnel balance dampers installed and, subsequently, removed. Modifications to the rotor hub were tested. These included a reduction in the rotor control system stiffness and increased flexbeam structural damping. The primary objective of the test was to determine aeroelastic stability of the fundamental flexbeam/blade chordwise bending mode. The rotor was stable for all conditions. Damping of the rotor chordwise bending mode increases with increased collective pitch angle at constant operating conditions. No significant decrease in rotor damping occured due to frequency coalescence between the blade chordwise fundamental bending mode and the support system.

Warmbrodt, W.↗
NASA NTRS1981

An analytical approach to airfoil icing

An analytical procedure has been developed to predict rime ice growth on unprotected airfoil sections and to evaluate the aerodynamic performance. A time stepping method is used in which: (1) water droplet trajectories are calculated, (2) a rime ice shape determined, (3) the flowfield around the iced airfoil is recalculated, and (4) the build-up process iterated upon until the desired icing time is reached. The performance of the iced airfoil shapes are then determined from existing analytic methods. Rime ice shapes determined in the NASA Lewis Icing Research Tunnel on a modified NACA 64 series airfoil agree well with the shapes predicted by the analytical method. Measured and predicted increases in drag due to the rime ice also agree favorably. A simplified scaling analysis is also presented and verified which provides the duplication of full scale results of rime ice accretions in small scale model tests.

Bragg, M. B.↗
NASA NTRS1981

Design and development of the combustor inlet diffuser for the NASA/GE energy efficient engine

Results of an experimental investigation of the aerodynamic performance of a split duct annular combustor inlet diffuser system are presented. Several diffuser configurations were investigated in 3X-scale water table tests and the preferred design was evaluated in full-scale annular airflow model tests. Pressure recovery and flow losses were determined as a function of prediffuser inlet velocity profile, flow extraction at the prediffuser exit, and distribution of flow in the combustor. Inlet velocity profile and turbulence levels were found to have a pronounced effect on system performance. Flow extraction at the prediffuser exit was found to have little influence on system performance. Generally, the annular split duct diffuser system was found to satisfy the performance objectives for the engine.

Sabla, P. E.↗
NASA NTRS1983

Supersonic-Wing Nonlinear Aerodynamics

Supersonic Wing Nonlinear Aerodynamics computer program, LTSTAR, estimates nonlinear aerodynamics characteristics of wing at supersonic speeds. Program provides generally improved predictions of wing overall force and moment coefficients. LTSTAR is useful in design studies aimed at aerodynamic performance optimization and providing more-realistic tradeoff information for selection of wing planform geometry and airfoil section parameters.

Carlson, H. W.↗
NASA NTRS1981

Low speed testing of the inlets designed for a tamden-fan V/STOL nacelle

An approximately 0.25 scale model of a tandem fan nacelle, designed for a subsonic V/STOL aircraft, was tested in a Lewis wind tunnel. Model variables included long and short aft inlet cowls and the addition of exterior strakes to the short inlet cowl. Inlet pressure recoveries and distortion were measured at pitch angles to 40 deg and at combinations of pitch and yaw to 30 deg. Airspeeds covered a range to 135 knots (69 m/sec). The short aft inlet with added strakes had the best aerodynamic performance and is considered suitable for the intended V/STOL application.

Williams, R. C.↗
NASA NTRS1981

Airframe-propulsion system aerodynamic interference predictions at high transonic Mach numbers including off-design engine airflow effects

The transonic speed regime for airplanes at conditions where inlet spillage takes place is discussed. A wind tunnel test program to evaluate aerodynamic performance penalties associated with propulsion system installation and operation at subsonic through low supersonic speeds was conducted. The accuracy of analytic methods for predicting transonic engine airframe interference effects was assessed. Study variables included Mach number, angle of attack, relative nacelle location, and nacelle mass flow ratio. Results include test theory comparisons of forces as well as induced pressure fields. Prediction capability of induced shock wave strength and locations is assessed. It was found that large interference forces due to engine location and flow spillage occur at transonic speeds, that theory explains these effects; and that theory can predict quantitatively these effects.

Kulfan, R. M.↗
NASA NTRS1982

Jet V/STOL wind-tunnel simulation and groundplane effects

The pretest preparation necessary to define the objectives of an appropriate investigation into the jet V/STOL wind tunnel simulation and ground plane effects were examined. Low speed wind tunnel testing of V/STOL aircraft concepts to determine the aerodynamic propulsion interaction effects during the transition between hover and wingborne flight is a necessary step in the development cycle of this type of aircraft. Powered models are normally used to determine the aerodynamic performance characteristics. Several factors which influence the selection of the model concept and the engine simulator are discussed. Some of the test techniques important for this class of aircraft model are examined. Wind tunnel wall effects important to this aircraft testing with special emphasis on groundplane effects are reviewed.

Margason, R. J.↗
NASA NTRS1982

A FORTRAN program for calculating three dimensional, inviscid and rotational flows with shock waves in axial compressor blade rows: User's manual

A FORTRAN-IV computer program was developed for the calculation of the inviscid transonic/supersonic flow field in a fully three dimensional blade passage of an axial compressor rotor or stator. Rotors may have dampers (part span shrouds). MacCormack's explicit time marching method is used to solve the unsteady Euler equations on a finite difference mesh. This technique captures shocks and smears them over several grid points. Input quantities are blade row geometry, operating conditions and thermodynamic quanities. Output quantities are three velocity components, density and internal energy at each mesh point. Other flow quanities are calculated from these variables. A short graphics package is included with the code, and may be used to display the finite difference grid, blade geometry and static pressure contour plots on blade to blade calculation surfaces or blade suction and pressure surfaces. The flow in a low aspect ratio transonic compressor was analyzed and compared with high response total pressure probe measurements and gas fluorescence static density measurements made in the MIT blowdown wind tunnel. These comparisons show that the computed flow fields accurately model the measured shock wave locations and overall aerodynamic performance.

Thompkins, W. T., Jr.↗
NASA NTRS1982

Viscous effect on airfoils for unsteady transonic flows

The viscous effect on aerodynamic performance of an arbitrary airfoil executing low frequency maneuvers during transonic flight was investigated. The small disturbance code, LTRAN2, was modified by using a conventional integral method, BLAYER, for the boundary layer and an empirical relation, viscous wedge, for simulating the suddenly thickened boundary layer behind the shock. Before the shock, only the boundary layer displacement thickness was evaluated. After the shock, the empirical wedge thickness was superimposed on the boundary layer thickness along the surface as well as in the wake region. The pressure coefficients were calculated for both steady and unsteady states. The viscous solution takes fewer iterations to obtain the converged steady state solution. Comparisons made with experimental data and the inviscid solution show that the viscous solution agrees better with the experimental data with about the same (or slightly less) amount of computational time.

Lee, S. C.↗
NASA NTRS1982

Small axial turbine stator technology program

An experimental investigation was conducted to determine the effects of surface finish, fillet radius, inlet boundary layer thickness, and free-stream inlet turbulence level on the aerodynamic performance of a small axial flow turbine stator. The principal objective of this program was to help understand why large turbine efficiency is not maintained when a large turbine is scaled to a smaller size. The stator used in this program as a one-sixth scale of a 762 mm (30 in.) diameter stator design with 50 vanes having a vane height of 17 mm (0.666 in.) and an aspect ratio of 1.77. A comprehensive overall test matrix was used to provide a complete engineering understanding of the effects of each variable over the full range of all the other variables. The range of each variable investigated was as follows: surface finish 0.1 micro (4 micro in.) to 2.4 micro (95 micro in.); boundary layer thickness 2 to 25 percent of channel height at each wall; fillet radius 0 mm (0 in.) to 1.0 mm (.040 in.) and turbulence 2 to 12 percent.

Brockett, W.↗
NASA NTRS1981

Jet V/STOL wind-tunnel simulation and groundplane effects

Low-speed wind-tunnel testing of V/STOL aircraft concepts to determine the aerodynamic-propulsion interaction effects during the transition between hover and wingborne flight is a necessary step in the development cycle of this type of aircraft. Powered models are normally used to determine the aerodynamic performance characteristics. This paper examines some of the pretest preparation necessary to define the objectives of an appropriate investigation. Several factors which influence the selection of the model concept and the engine simulator are discussed. In addition, some of the test techniques important for this class of aircraft model are examined. Finally, the paper reviews some of the wind-tunnel wall effects important to this type of aircraft testing with special emphasis on groundplane effects.

Margason, R. J.↗