Search NASA⌕ Search

SEARCH · Search NASA

Results for “Base Composition”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Biomimetic Catalysts Based on Au@ZnO–Graphene Composites for the Generation of Hydrogen by Water Splitting

For some decades, the scientific community has been looking for alternatives to the use of fossil fuels that allow for the planet’s sustainable and environmentally-friendly development. To do this, attempts have been made to mimic some processes that occur in nature, among which the photosystem-II stands out, which allows water splitting operating with different steps to generate oxygen and hydrogen. This research presents promising results using synthetic catalysts, which try to simulate some natural processes, and which are based on Au@ZnO–graphene compounds. These catalysts were prepared by incorporating different amounts of gold nanoparticles (1 wt.%, 3 wt.%, 5 wt.%, 10 wt.%) and graphene (1 wt.%) on the surface of synthesized zinc oxide nanowires (ZnO NWs), and zinc oxide nanoparticles (ZnO NPs), along with a commercial form (commercial ZnO) for comparison purposes. The highest amount of hydrogen (1127 μmol/hg) was reported by ZnO NWs with a gold and graphene loadings of 10 wt.% and 1 wt.%, respectively, under irradiation at 400 nm. Quantities of 759 μmol/hg and 709 μmol/hg were obtained with catalysts based on ZnO NPs and commercial ZnO, respectively. The photocatalytic activity of all composites increased with respect to the bare semiconductors, being 2.5 times higher in ZnO NWs, 8.8 times higher for ZnO NPs, and 7.5 times higher for commercial ZnO. The high photocatalytic activity of the catalysts is attributed, mainly, to the synergism between the different amount of gold and graphene incorporated, and the surface area of the composites.

Machín, Abniel (ORCID:0000000341343344)↗
DOE OSTI2023

A helical actuator driven by biased SMA: design, model, and experiment

A helical actuator driven by biased shape memory alloy (SMA) patterns embedded into a soft composite ribbon base is presented in this work. Instead of common U-shape SMA wires, a single SMA wire is woven into planar patterns, which enable helical deformation of the composite ribbon from an initially flat geometry. An analytical static model is established for accurate and rapid prediction of the helical reconfiguration arising from the shape memory effect of woven SMA patterns, followed by validation of the static model using the finite element method (FEM). The finite element results are compared with the analytical solutions given by this static model, which show a high agreement. Parametric study of the influences of eight independent design variables on the dependent helical parameters, such as combined curvatures, pitches, and helical angles, is completed. It is found that the helically deformed geometry is mainly dominated by diameters, biased positions, inclined angles, and numbers of skewed segments of the SMA wire. Fabrication and in-situ experimental test of a prototype of such helical actuators qualitatively demonstrate its dramatic three-dimensional (3D) spiral reconfiguration from a two-dimensional (2D) flat ribbon. In conclusion, such SMA patterns will allow more diverse designs of soft actuators for a wider range of robotic applications.

36 MATERIALS SCIENCE↗
DOE OSTI2022

The missing base molecules in atmospheric acid–base nucleation

Abstract Transformation of low-volatility gaseous precursors to new particles affects aerosol number concentration, cloud formation and hence the climate. The clustering of acid and base molecules is a major mechanism driving fast nucleation and initial growth of new particles in the atmosphere. However, the acid–base cluster composition, measured using state-of-the-art mass spectrometers, cannot explain the measured high formation rate of new particles. Here we present strong evidence for the existence of base molecules such as amines in the smallest atmospheric sulfuric acid clusters prior to their detection by mass spectrometers. We demonstrate that forming (H2SO4)1(amine)1 is the rate-limiting step in atmospheric H2SO4-amine nucleation and the uptake of (H2SO4)1(amine)1 is a major pathway for the initial growth of H2SO4 clusters. The proposed mechanism is very consistent with measured new particle formation in urban Beijing, in which dimethylamine is the key base for H2SO4 nucleation while other bases such as ammonia may contribute to the growth of larger clusters. Our findings further underline the fact that strong amines, even at low concentrations and when undetected in the smallest clusters, can be crucial to particle formation in the planetary boundary layer.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS2006

The Dos and Don'ts of how to Build a Planet, Using the Moon as an Example

The bulk chemical compositions of planets may yield important clues concerning planetary origins. Failing that, bulk compositions are still important, in that they constrain calculation of planetary mineralogies and also constrain the petrogenesis of basaltic magmas. In the case of the Earth, there is little or no debate about the composition of the Earth's upper mantle. This is because our sample collections contain peridotitic xenoliths of that mantle. The most fertile of these are believed to have been little modified from their primary compositions. Using these samples and chondritic meteorites as a starting point, small perturbations on the compositions of existing samples allow useful reconstruction of the bulk silicate Earth (BSE). Elsewhere, I have argued that the next simplest case is the Eucrite Parent Body (EPB). Reconstructions based on Sc partitioning indicate that the EPB can be well approximated by a mixture of 20% eucrite and 80% equilibrium olivine. This leads to a parent body that is similar to CO (or devolatilized CM) chondrites. Partial melting experiments on CM chondrites confirm this model, because the residual solids in these experiments are dominated by olivine with minor pigonite [3]. The most difficult bodies to reconstruct are those that have undergone the most differentiation. Both the Moon and Mars may have passed through a magma ocean stage. In any event, lunar and martian basalts, unlike eucrites, were not derived from undifferentiated source regions. Reconstructions are primarily based on compositional trends within the basalts themselves with some critical assumptions: (i) Refractory lithophile elements (Ca, Al, REE, actinides) are presumed to be in chondritic relative abundances; and (ii) some major element ratio is believed to exist in a chondritic ratio (e.g., Mg/Si, Mg/Al). The most commonly used parameter is Mg/Si.

Jones, J. H.↗
DOE OSTI2020

Sensors and methods for monitoring flying objects

Described herein are sensing methods, sensor systems, and non-transitory, computer-readable, storage media having programs for long-duration, continuous monitoring of flying objects during the day or the night and regardless of weather conditions. The methods and systems are computationally efficient and can provide compact, three-dimensional representations of motion from the observed object. A 3D track of the flying object can be generated from a point-matched pair of stereo composite motion track images and not directly from the videos, wherein each composite motion track image is based on a composite of a plurality of video frames composited in part according to video frame numbers.

Matzner, Shari↗
NASA NTRS1993

Particle sizes and composition of Mars atmospheric dust based upon Viking and Mariner 9 observations

Mars atmospheric dust can play an important role in the thermal structure of the Mars atmosphere during periods of high dust loading. However, the radiative properties of Mars atmospheric dust remain uncertain due to uncertain definitions of the dust composition and size distribution. The analysis by Toon et al., of Mariner 9 IRIS spectra during the 1971-1972 global dust storm indicated a reasonable match between the modeled 9-micron absorption of montmorillinite and the observed 9-micron absorption. Toon et al. also determined that an effective (cross-section weighted) mean radius of 2.5 microns (R(sub mode) = 0.4 microns) provided a consistent fit of montmorillinite to the IRIS dust spectra at 9 microns. Pollack et al. analyzed Viking lander observations of atmospheric extinction and scattering at visible-near IR wavelengths (0.5-1.0 microns), and obtained consistency with the Toon et al. dust size distribution when the effects of nonspherical particle shapes were included. An additional, minor (1 percent) component of visible-ultraviolet absorbing material was required to model the derived visible (0.86) and ultraviolet (0.4-0.6) single-scattering albedos of the dust, since montmorillinite does not absorb sufficiently in this wavelength region. A combined analysis of the Viking IRTM and Mariner 9 observations was conducted to reassess the model of Mars atmospheric ultraviolet-to-infrared measurements of dust absorption and scattering. The optical constants for palagonite are incorporated in a doubling-adding radiative transfer model of the Mars atmosphere to simulate Mariner 9 IRIS spectra as well as the Viking IRTM IR band observations. Visible and ultraviolet single-scattering albedos based on the Hansen and Travis Mie scattering code were also derived. A tentative conclusion is that smaller dust particles (R(sub mode) = 0.15 microns, cross-section weighted mean R = 1.2 microns) composed of palagonite provide a much improved fit to the Mariner 9 IRIS spectra; agreement with the observed ratio of visible-to-infrared extinction opacities; and ultraviolet and visible single-scattering albedos comparable to their observed values.

Clancy, R. T.↗
NASA NTRS1977

Coronary heart disease index based on longitudinal electrocardiography

A coronary heart disease index was developed from longitudinal ECG (LCG) tracings to serve as a cardiac health measure in studies of working and, essentially, asymptomatic populations, such as pilots and executives. For a given subject, the index consisted of a composite score based on the presence of LCG aberrations and weighted values previously assigned to them. The index was validated by correlating it with the known presence or absence of CHD as determined by a complete physical examination, including treadmill, resting ECG, and risk factor information. The validating sample consisted of 111 subjects drawn by a stratified-random procedure from 5000 available case histories. The CHD index was found to be significantly more valid as a sole indicator of CHD than the LCG without the use of the index. The index consistently produced higher validity coefficients in identifying CHD than did treadmill testing, resting ECG, or risk factor analysis.

Townsend, J. C.↗
NASA NTRS1983

Continental crustal composition and lower crustal models

The composition of the upper crust is well established as being close to that of granodiorite. The upper crustal composition is reflected in the uniform REE abundances in shales which represent an homogenization of the various REE patterns. This composition can only persist to depths of 10-15 km, for heat flow and geochemical balance reasons. The composition of the total crust is model dependent. One constraint is that it should be capable of generating the upper granodioritic (S.L.) crust by partial melting within the crust. This composition is based on the andesite model, which assumes that the total crust has grown by accretion of island arc material. A representation of the growth rate of the continental crust is shown. The composition of the lower crust, which comprises 60-80% of the continental crust, remains a major unknown factor for models of terrestrial crustal evolution. Two approaches are used to model the lower crust.

Taylor, S. R.↗
NASA NTRS1993

Burning of a spherical fuel droplet in a uniform flowfield with exact property variation

An analytical/numerical model is developed for single droplet evaporation and burning in a convective flowfield. The model is based on the boundary-layer approach, and chemical reaction kinetics are represented by a one-step, finite-rate reaction mechanism, while variation of gas properties with temperature and gas composition is based on the kinetic theory of gases. Four droplet models differing in the degree of complexity concerning property variation and chemistry are compared. Comparisons are also provided with existing empirical correlations for convective droplet evaporation and burning.

Madooglu, K.↗
NASA NTRS1977

Influence of temperature change on optimum laminate design

Results of a laminate optimization study, which includes prescribed temperature change and mechanical loading conditions, are presented. Minimum-weight designs for balanced symmetric laminates are obtained subject to strength, membrane stiffness, and minimum thickness requirements, while including and omitting temperature change effects. Based on a first ply failure design philosophy and employing a linear thermoelastic analysis, it is shown that taking temperature decrease effects into account leads to substantial weight penalties in strength critical fiber composite laminates. Numerical results are presented for representative fiber composite materials based on three commonly used combined stress failure criteria.

Schmit, L. A., Jr.↗
NASA NTRS1995

EMI Shields made from intercalated graphite composites

Electromagnetic interference (EMI) shielding typically makes up about twenty percent of the mass of a spacecraft power system. Graphite fiber/polymer composites have significantly lower densities and higher strengths than aluminum, the present material of choice for EMI shields, but they lack the electrical conductivity that enables acceptable shielding effectiveness. Bromine intercalated pitch-based graphite/epoxy composites have conductivities fifty times higher than conventional structural graphite fibers. Calculations are presented which indicate that EMI shields made from such composites can have sufficient shielding at less than 20% of the mass of conventional aluminum shields. EMI shields provide many functions other than EMI shielding including physical protection, thermal management, and shielding from ionizing radiation. Intercalated graphite composites perform well in these areas also. Mechanically, they have much higher specific strength and modulus than aluminum. They also have shorter half thicknesses for x-rays and gamma radiation than aluminum. Thermally, they distribute infra-red radiation by absorbing and re-radiating it rather than concentrating it by reflection as aluminum does. The prospects for intercalated graphite fiber/polymer composites for EMI shielding are encouraging.

Gaier, James R.↗
NASA NTRS2003

Individual Aerosol Particles from Biomass Burning in Southern Africa: Compositions and Size Distributions of Carbonaceous Particles - 1

Individual aerosol particles in smoke plumes from biomass fires and in regional hazes in southern Africa were studied using analytical transmission electron microscopy (TEM), which allowed detailed characterization of carbonaceous particle types in smoke and determination of changes in particle properties and concentrations during smoke aging. Based on composition, morphology, and microstructure, three distinct types of carbonaceous particles were present in the smoke: organic particles with inorganic (K-salt) inclusions, tar ball particles, and soot. The relative number concentrations of organic particles were largest in young smoke, whereas tar balls were dominant in a slightly aged (1 hour) smoke from a smoldering fire. Flaming fires emitted relatively more soot particles than smoldering fires, but soot was a minor constituent of all studied plumes. Further aging caused the accumulation of sulfate on organic and soot particles, as indicated by the large number of internally mixed organic/sulfate and soot/sulfate particles in the regional haze. Externally mixed ammonium sulfate particles dominated in the boundary layer hazes, whereas organic/sulfate particles were the most abundant type in the upper hazes. Apparently, elevated haze layers were more strongly affected by biomass smoke than those within the boundary layer. Based on size distributions and the observed patterns of internal mixing, we hypothesize that organic and soot particles are the cloud-nucleating constituents of biomass smoke aerosols. Sea-salt particles dominated in the samples taken in stratus clouds over the Atlantic Ocean, off the coast of Namibia, whereas a distinct haze layer above the clouds consisted of aged biomass smoke particles.

Posfai, Mihaly↗
NASA NTRS1977

Cooling rates for lunar samples determined with a diffusion model for phosphide exsolution

A numerical model for diffusion-controlled phase growth has been applied to the exsolution of phosphide lamellae in lunar metal grains. Computer simulations reproduce observed composition profiles, and reveal the influence of cooling rate on dimensional and compositional parameters of phosphide and metal. At lower cooling rates, phosphide lamellae are larger and the concentration of P in the metal host close to the interface is lower. Cooling rates inferred for Apollo 16 samples, based on compositions and dimensions of the phosphide-metal grains, are mostly in the range 1-100 C/day. These rates correspond to burial depths of 5-0.5 m for melt rocks and 3-0.3 m for breccias. This is in good agreement with thicknesses of lunar cooling units determined by other techniques.

Hewins, R. H.↗
DOE OSTI2021

Large-scale continuous carbon/glass fiber additive-compression molded composites

Additive Manufacturing (AM) or 3-D printing has advanced from small-scale desktop printers to large-scale printers. Most of the present large-scale printers utilize feedstock materials in the form of pellets to create composite structures. To create structurally robust composite parts, reinforcements in the form of short fibers (carbon or glass) are often used to impart mechanical properties to the printed parts. However, poor mechanical properties in Z-direction and high porosity of pellets-based printed composites compared to composite manufactured using traditional methods are serious concerns. The authors report a combined approach in the present work, where fiber reinforced composites are printed with a high-throughput continuous fiber deposition method followed by a secondary compression molding process. A specially designed end-effector mounted on a robotic arm is used to print composite preforms. Continuous comingled fibers (Thermofiber 12K CF-PA12, Thermofiber 12K S2-PA12, and Hybrid Thermofiber 12K CF-PA12+PEEK PA6) embedded in the thermoplastic nylon matrix are printed to create composite preform plaques. The printed preforms were further compression molded (CM) using a hydraulic hot-press to create highly consolidated composite parts. The mechanical properties of the continuous fiber composites produced by this combined approach are improved significantly due to the highly aligned continuous fibers and reduced porosity. Flexural strength, flexural modulus, and tensile modulus of AM-CM Thermofiber 12K CF-PA12 UD sample were 615.37 MPa, 75.65 GPa, and 122.23 GPa, respectively.

Kumar, Vipin↗
DOE OSTI2025

Effect of metal-free mesoporous silica incorporated ZSM-5 composite on thermo-catalytic pyrolysis of polypropylene

Although different zeolites impregnated with transition metals have been used in catalytic deconstruction of waste plastics to other products, the influence of hierarchical structures on conversion and product selectivity in plastic upcycling has not been thoroughly investigated. This research explores a transition metal free zeolite-based hierarchical composite, synthesized by incorporating SBA-15 in ZSM-5 framework, for efficient thermos-catalytic upcycling of polypropylene (PP). Thermogravimetric analysis reveals that ZSM-5@SBA-15 can break down PP at a significantly lower temperature, 240 °C, compared to that of pristine PP using ZSM-5 or SBA-15. In addition, pyrolysis of PP at 400 °C using ZSM-5@SBA-15 composite outperforms ZSM-5 or SBA-15 used separately and yields 90 % conversion with 70 % selectivity to propene. The presence of mesopores in the catalyst appears to reduce the diffusion resistance of intermediate products for successive scission, thereby reducing the activation energy of reaction and improving catalytic activity. In conclusion, the hierarchical composite ZSM-5@SBA-15 has significant potential for upcycling of PP into valuable monomers and lighter olefins, with lower energy demands, enhancing the economic feasibility of the process.

ZSM-5@SBA-15↗
NASA NTRS2021

Columnar Aerosol Types and Compositions Over Peninsular Southeast Asia Based on Long-Term AERONET Data

Aerosol chemical components such as black carbon (BC) and brown carbon (BrC) regulate aerosol optical properties, which in turn drive the atmospheric radiative forcing estimations due to aerosols. In this study, we used the long-term measurements from AERONET (Aerosol Robotic Network) to better understand the aerosol types and composition with respect to their seasonal and spatial variabilities in peninsular Southeast Asia (PSEA, here defined as Vietnam, Cambodia, Thailand, Laos, and Myanmar). Two methods (i.e., aerosol type cluster and aerosol component retrieval) were applied to determine the aerosol type and chemical composition during the biomass-burning (BB) season. AERONET sites in northern PSEA showed a higher AOD (aerosol optical depth) compared to that of southern PSEA. Differences in land use pattern, geographic location, and weather regime caused much of the aerosol variability over PSEA. Lower single-scattering albedo (SSA) and higher fine-mode fraction (FMF) values were observed in February and March, suggesting the predominance of BB type aerosols with finer and stronger absorbing particles during the dry season. However, we also found that the peak BB month (i.e., March) in northern PSEA may not coincide with the lowest SSA once dust particles have mixed with the other aerosols. Furthermore, we investigated two severe BB events in March of 2014 and 2015, revealing a significant BrC fraction during BB event days. On high AOD days, although the BC fraction was high, the BrC fraction remained low due to lack of aerosol aging. This study highlights the dominance of carbonaceous aerosols in the PSEA atmosphere during the BB season, while also revealing that transported dust particles and BrC aerosol aging may introduce uncertainties into the aerosol radiative forcing calculation.

Sheng-Hsiang Wang↗
DOE OSTI2025

Machine learning informed rational design of high entropy double perovskite oxide universal air/steam electrodes for solid oxide electrochemical cells

Due to their high efficiency and versatility, solid oxide electrochemical cells (SOCs) are poised to play a significant role in future energy conversion and storage applications. In recent years, SOCs have bifurcated into two distinct categories: traditional oxygen-ion conducting SOCs that typically operate from ∼650—850 °C and the more recent proton-conducting ceramic (PCC) SOCs that typically operate from ∼400—650 °C. Current performance and lifetime of both oxygen-ion conducting SOCs and PCCs is primarily limited by the air/steam electrode, which facilitates the oxygen reduction reaction (ORR) during fuel cell operation and must also facilitate the oxygen evolution reaction (OER) during electrolysis operation. Here, we present a newly designed high-entropy double perovskite oxide suitable as a universal ORR/OER electrode for both oxygen-ion conducting SOCs and PCCs. Machine learning methods are applied to identify chemical descriptors for highly catalytic high-entropy double perovskite oxides (AA’B 2 O 6 ) across a large compositional space. Based on the machine-learning guidance, we ultimately converge on Ba 0.9 Cs 0.1 (Ca 0.2 Gd 0.2 La 0.2 Pr 0.2 Sr 0.2 )Co 1.5 Fe 0.5 O 6 (CsBaHEO) as a universal air/steam electrode. Structure stabilization is accomplished by an equimolar five-cation high-entropy composition on the A’-site, while cesium substitution on the A-site enhances the electrical conductivity and leads to a higher oxygen vacancy concentration. This material exhibits versatility and high performance in reversible oxygen-ion SOCs, reversible PCCs, and also large-scale tubular PCCs. For example, the CsBaHEO-based PCC reaches 1018 mW∙cm −2 at 600°C, while a large-scale tubular PCC using CsBaHEO for electrolysis achieves a hydrogen production rate of 21.314 ML∙min −1 at 600 °C.

Cell↗
NASA NTRS1980

Evaluation of multispectral middle infrared aircraft images for lithologic mapping in the East Tintic Mountains, Utah

Six channels of multispectral middle infrared (8 to 14 micron) aircraft scanner data were acquired over the East Tintic mining district, Utah. This area has high relief and moderate vegetation and consists mainly of Tertiary silicic igneous rocks and Paleozoic quartzite and carbonate rocks that have been locally hydrothermally altered. These digital-image data were computer processed to create a color-composite image based on principal component transformations. Color differences in this image are related to the spectral differences in the surface material and allow discrimination of several rock types, depending primarily on their silica content. When combined with a visible and near infrared color-composite image from a previous flight, with limited field checking, it is possible to discriminate quartzite, carbonate rocks, quartz latitic and quartz monzonitic rocks, latitic and monzonitic rocks, silicified altered rocks, argillized altered rocks, and vegetation.

Kahle, A. B.↗