Search NASA⌕ Search

SEARCH · Search NASA

Results for “Capacity estimation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

The Case for Natural Gas Fueled Solid Oxide Fuel Cell Power Systems for Distributed Generation

Natural-gas-fueled solid oxide fuel cell (NGSOFC) power systems yield electrical conversion efficiencies exceeding 60% and may become a viable alternative for distributed generation (DG) if stack life and manufacturing economies of scale can be realized. Currently, stacks last approximately 2 years and few systems are produced each year because of the relatively high cost of electricity from the systems. If mass manufacturing (10,000 units per year) and a stack life of 15 years can be reached, the cost of electricity from an NGSOFC system is estimated to be about 7.7 ¢/kWh, well within the price of commercial and residential retail prices at the national level (9.9-10¢/kWh and 11-12 ¢/kWh, respectively). With an additional 5 ¢/kWh in estimated additional benefits from DG, NGSOFC could be well positioned to replace the forecasted 59-77 gigawatts of capacity loss resulting from coal plant closures due to stricter emissions regulations and low natural gas prices.

distributed generation↗

Techno-Economic Analysis of Recuperated Joule-Brayton Pumped Thermal Energy Storage

This article describes a techno-economic model for pumped thermal energy storage systems based on recuperated Joule-Brayton cycles and two-tank liquid storage. Models have been developed for each component, with particular emphasis on the heat exchangers. Economic metrics such as the power and energy capital costs (i.e., per-kW and per-kWh capacity) and levelized cost of storage are evaluated by gathering numerous cost correlations from the literature, thereby enabling estimates of uncertainty. It is found that the use of heat exchangers with effectivenesses up to 0.95 is economically worthwhile, but higher values lead to rapidly escalating component size and system cost. Several hot storage fluids are considered; those operating at the highest temperatures (chloride salts) improve the round-trip efficiency but the benefit is marginal and may not warrant the additional material costs and risk when compared to lower-temperature nitrate salts. Cost-efficiency trade-offs are explored using a multi-objective optimization algorithm, yielding optimal designs with round-trip efficiencies in the range 59-72% and corresponding levelized storage costs of 0.12 0.03 and 0.38 0.10 $/kWhe. Lifetime costs are competitive with lithium-ion batteries for discharging durations greater than 6 h under current scenarios.

Carnot battery↗

Influence of site and soil properties on the DRIFT spectra of northern cold-region soils [Influence of site and soil properties on the mid-infrared spectra of northern cold-region soils]

Here, we investigated the influence of site characteristics and soil properties on the chemical composition of organic matter in soils collected from a latitudinal transect across Alaska through analysis of diffuse reflectance Fourier transform mid infrared (MidIR) spectra of bulk soils. The study included 119 soil samples collected from 28 sites including tundra, boreal forest, and grassland ecosystems. Organic, mineral, and cryoturbated soil horizons, both seasonally and perennially frozen, from a variety of depths and edaphic conditions were examined. The amount and chemical composition of organic matter as well as site and soil properties exerted a strong influence on the MidIR spectra. The spectra were highly sensitive to the extent of organic matter decomposition, enabling the ordination of Oi, Oe and Oa organic horizons. Differences in absorbance intensity for several spectral bands indicated that Oi horizons contained greater abundance of relatively fresh residues, phenolic-OH compounds, aliphatic compounds (waxes, lipids and fats), and carbohydrates. In contrast, Oa horizons had a greater presence of amide groups (possibly from microbial residues), aromatics, C=C bonds, carboxylates and carboxylic acids. Another significant factor differentiating these horizons was the incorporation of clays and silicates into the decomposing organic matter of Oa horizons. Calculated height peak ratios showed a clear trend to greater decomposition among Oi, Oe and Oa. The MidIR spectra were related to many site/soil attributes including land cover type, parent material, and associated factors, such as permafrost presence/absence, soil drainage, horizon depth, bulk density, cation exchange capacity, and pH. Single MidIR spectral bands were identified that might be used in future studies to quickly estimate the organic and inorganic carbon, total nitrogen, and carbon:nitrogen ratios of soils from northern latitudes. Lastly, our results demonstrate that the information contained in MidIR spectra of bulk soil integrates the quantity and chemical composition of soil organic matter with soil forming factors and highlights the potential for using this information to assess the degradation state of organic matter stored in northern cold-region soils.

58 GEOSCIENCES↗

Apigenin potentiates the antitumor activity of 5-FU on solid Ehrlich carcinoma: Crosstalk between apoptotic and JNK-mediated autophagic cell death platforms

Background: Although 5- Fluorouracil (5-FU) has exhibited effectiveness against cancer, novel therapeutic strategies are needed to enhance its antitumor efficiency and modulate its cytotoxity. Apigenin, a flavonoid present in fruits and vegetables, is a potent dietary phytochemical effective in cancer chemoprevention. Aim: This study was undertaken to investigate the potential synergistic antitumor activity of apigenin and 5-FU on Solid Ehrlich carcinoma (SEC). Methods: Eighty Swiss albino male mice were divided into four equal groups: vehicle treated control SEC, SEC + 5-FU, SEC + apigenin, SEC + 5-FU + apigenin. Beclin-1 and caspases 3, 9 and JNK activities were estimated by ELISA; mRNA expression levels of the antiapoptotic gene Mcl-1 were estimated using quantitative real-time RT-PCR, while tissue malondialdehyde (MDA), glutathione peroxidase and total antioxidant capacity were evaluated spectrophotometrically. A part of the tumor was examined for histopathological and Ki-67 immunohistochemistry analysis. Results: 5-FU and/or apigenin caused significant increase in tissue levels of Beclin-1, caspases 3, 9 and JNK activities, MDA with significant decrease in tumor volume, Mcl-1expression, tissue glutathione peroxidase and total antioxidant capacity and alleviated the histopathological changes with significant decrease of Ki-67 proliferation index compared to vehicle treated SEC control group. In conclusion: The combination of 5-FU and apigenin had a greater effect than each of 5-FU or apigenin alone against solid Ehrlich carcinoma in mice. - Highlights: • Apigenin potentiated 5-FU cytotoxicity in EAC solid tumor models in vivo. • It acted via autophagy stimulation, downregulating MCL-1 and Ki-67 expression. • It caused JNK activation and ROS accumulation; resulted in tumor growth inhibition. • Apigenin can be used as a co-adjuvant agent in cancer therapy.

60 APPLIED LIFE SCIENCES↗

Verifying the Dependence of Fractal Coefficients on Different Spatial Distributions

A fractal distribution requires that the number of objects larger than a specific size r has a power-law dependence on the size N(r) = C/r{sup D}propor tor{sup -D} where D is the fractal dimension. Usually the correlation integral is calculated to estimate the correlation fractal dimension of epicentres. A 'box-counting' procedure could also be applied giving the 'capacity' fractal dimension. The fractal dimension can be an integer and then it is equivalent to a Euclidean dimension (it is zero of a point, one of a segment, of a square is two and of a cube is three). In general the fractal dimension is not an integer but a fractional dimension and there comes the origin of the term 'fractal'. The use of a power-law to statistically describe a set of events or phenomena reveals the lack of a characteristic length scale, that is fractal objects are scale invariant. Scaling invariance and chaotic behavior constitute the base of a lot of natural hazards phenomena. Many studies of earthquakes reveal that their occurrence exhibits scale-invariant properties, so the fractal dimension can characterize them. It has first been confirmed that both aftershock rate decay in time and earthquake size distribution follow a power law. Recently many other earthquake distributions have been found to be scale-invariant. The spatial distribution of both regional seismicity and aftershocks show some fractal features. Earthquake spatial distributions are considered fractal, but indirectly. There are two possible models, which result in fractal earthquake distributions. The first model considers that a fractal distribution of faults leads to a fractal distribution of earthquakes, because each earthquake is characteristic of the fault on which it occurs. The second assumes that each fault has a fractal distribution of earthquakes. Observations strongly favour the first hypothesis.The fractal coefficients analysis provides some important advantages in examining earthquake spatial distribution, which are: - Simple way to quantify scale-invariant distributions of complex objects or phenomena by a small number of parameters. - It is becoming evident that the applicability of fractal distributions to geological problems could have a more fundamental basis. Chaotic behaviour could underlay the geotectonic processes and the applicable statistics could often be fractal.The application of fractal distribution analysis has, however, some specific aspects. It is usually difficult to present an adequate interpretation of the obtained values of fractal coefficients for earthquake epicenter or hypocenter distributions. That is why in this paper we aimed at other goals - to verify how a fractal coefficient depends on different spatial distributions. We simulated earthquake spatial data by generating randomly points first in a 3D space - cube, then in a parallelepiped, diminishing one of its sides. We then continued this procedure in 2D and 1D space. For each simulated data set we calculated the points' fractal coefficient (correlation fractal dimension of epicentres) and then checked for correlation between the coefficients values and the type of spatial distribution.In that way one can obtain a set of standard fractal coefficients' values for varying spatial distributions. These then can be used when real earthquake data is analyzed by comparing the real data coefficients values to the standard fractal coefficients. Such an approach can help in interpreting the fractal analysis results through different types of spatial distributions.

58 GEOSCIENCES↗

Robust superconductivity with large upper critical field in Nb{sub 2}PdS{sub 5}

We report synthesis, structural details, and complete superconducting characterization of very recently discovered [Q. Zhang, Sci. Rep. 3, 1446 (2013)] Nb{sub 2}PdS{sub 5} new superconductor. The synthesized compound is crystallized in monoclinic structure with C2/m (#12) space group. Bulk superconductivity is seen in both ac/dc magnetic susceptibility and electrical resistivity measurements with superconducting transition temperature (T{sub c}) at 6 K. The upper critical field (H{sub c2}) being estimated from high field magneto-transport [ρ(T)H] measurements is above 240 kOe. The estimated H{sub c2}(0) is clearly above the Pauli paramagnetic limit of ∼1.84T{sub c}. Heat capacity (C{sub p}) measurements show clear transition with well defined peak at T{sub c}, but with lower jump than as expected for a Bardeen–Cooper–Schrieffer type superconductor. The Sommerfeld constant (γ) and Debye temperature (Θ{sub D}) as determined from low temperature fitting of C{sub P}(T) data are 32 mJ/mole-K{sup 2} and 263 K, respectively. Hall coefficients and resistivity in conjugation with electronic heat capacity indicates multiple gap superconductivity signatures in Nb{sub 2}PdS{sub 5}. We also studied the impact of hydrostatic pressure (0–1.97 Gpa) on superconductivity of Nb{sub 2}PdS{sub 5} and found nearly no change in T{sub c} for the given pressure range.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

The effect of rare-earth substitution on the Debye temperature of inorganic phosphors

In the quest to predict photoluminescent efficiency in rare-earth substituted inorganic phosphors, research has shown that materials consisting of ordered, rigid crystal structures tend to possess the highest photoluminescent quantum yields. A compound's Debye temperature (Θ D ), which can be calculated using ab initio calculations, is an ideal proxy for quantitatively comparing structural rigidity among different inorganic compounds, allowing potentially efficient phosphors to be selected from large crystal structure databases. However, the high computational cost of these calculations limits estimating Θ D for unsubstituted host crystal structures only. It is assumed that the low substitution concentration of the rare-earth luminescent center does not significantly influence a material's Debye temperature. This work evaluates the validity of this approximation by examining the effect of luminescent center substitution on a host structure's Θ D . Two well-known phosphors, (Y 1– x Ce x ) 3 Al 5 O 12 ( x = 0 – 0.05) and Ba 1-δ Eu δ MgAl 10 O 17 (δ = 0 – 0.15), were synthesized with varying rare-earth concentrations, while Θ D was computationally estimated and then determined by ultrasonic pulse-echo speed-of-sound and low-temperature heat capacity measurements. Overall, the ensuing results provide key implications for using Θ D as a proxy for structural rigidity in substituted inorganic compounds.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Evaluation of Phenylnaphthalenes as Heat Transfer Fluids for High Temperature Energy Applications

The thermodynamic properties of 1- and 2-phenyl substituted polyaromatic hydrocarbons have been measured and estimated under conditions relevant to heat transport applications almost to the critical point. Densities, vapor pressures, and heat capacity measurements were used to derive critical temperature, pressure and density for the phenylnaphthalenes. The thermal and radiolytic stability of 1-phenylnaphthalene was examined using thermogravimetric analysis, differential scanning calorimetery, and gamma irradiation. Low vapor pressure and resistance to thermal decomposition may make phenylnaphthalenes suitable for heat transfer applications involving parabolic solar collectors. In particular, 1-phenylnaphthalene has an advantage over high temperature inorganic salts for applications up to 800 K because it is a liquid at temperatures at or close to ambient. Thermal cycling would have to be restricted to temperatures below the critical point to avoid degradation of the fluid. Radiation stability was also tested by a 100 kGy irradiation of 1-phenylnaphthalene in a Co-60 irradiator. NMR analysis indicated 1.7 mol.% degradation, which although lower than observed for tributylphosphate/kerosene benchmark fluids for nuclear applications, is higher than that seen in imidazolium ionic liquids.

14 SOLAR ENERGY↗

Recovering Rare Earth Elements from Coal Mine Drainage Using Industrial Byproducts: Environmental and Economic Consequences

Coal mine drainage (CMD) impairs tens of thousands of kilometers of U.S. waterways each year, in part with the leaching of low concentrations of rare earth elements (REEs). REEs are essential for modern technologies, yet economically viable natural deposits are geospatially limited, thus engendering geopolitical concerns, and their mining is energy intense and environmentally destructive. This work summarizes laboratory-scale experimentalresults of a trap-extract-precipitate (TEP) process and uses the mass and energy balances to estimate the economic costs and environmental impacts of the TEP. The TEP process uses the alkalinity and filtering capacity of stabilized flue gas desulfurization (sFGD) material or water treatment plant (WTP) sludge to remediate CMD waters and extract REEs. Passive treatment systems that use WTP sludge are cheaper than those that use sFGD material ($\$$89,300/year or $\$$86/gT-REE vs. $\$$89,800/year or $\$$278/gT-REE) and have improved environmental performance across all indicators from two different impact assessment methods. These differences are largely attributable to the larger neutralizing capacity of WTP sludge in the treatment application.

01 COAL, LIGNITE, AND PEAT↗

Experimental evidence of a collinear antiferromagnetic ordering in the frustrated CoAl2O4 spinel

Nuclear magnetic resonance (NMR), neutron diffraction (ND), x-ray diffraction, magnetic susceptibility χ, and specific-heat measurements on the frustrated A-site spinel CoAl2O4 compound reveal a collinear antiferromagnetic ordering below TN = 9.8(2) K. A high-quality powder sample characterized by x-ray diffraction that indicates a relatively low Co-Al inversion parameter x=0.057(20) in (Co1-xAlx)[Al2-xCox]O4, shows a broad maximum around 15 K in χ(T) and a sharp peak at TN in heat capacity Cp. The average-ordered magnetic moment of Co2+ (S=32) ions at the A site is estimated to be 2.4(1) μB from NMR and 1.9(5) μB from ND which are smaller than the expected value of 3 μB for S=32 and g = 2. Antiferromagnetic spin fluctuations and correlations in the paramagnetic state are revealed from the χ, NMR, and ND measurements, which are due to spin frustration and site inversion effects in the system. The ND data also show short-range dynamic magnetic ordering that persists to a temperature that is almost twice TN.

36 MATERIALS SCIENCE↗

NNSA ASC Exascale Environment Planning, Applications Working Group, Report February 2011

The scope of the Apps WG covers three areas of interest: Physics and Engineering Models (PEM), multi-physics Integrated Codes (IC), and Verification and Validation (V&V). Each places different demands on the exascale environment. The exascale challenge will be to provide environments that optimize all three. PEM serve as a test bed for both model development and 'best practices' for IC code development, as well as their use as standalone codes to improve scientific understanding. Rapidly achieving reasonable performance for a small team is the key to maintaining PEM innovation. Thus, the environment must provide the ability to develop portable code at a higher level of abstraction, which can then be tuned, as needed. PEM concentrate their computational footprint in one or a few kernels that must perform efficiently. Their comparative simplicity permits extreme optimization, so the environment must provide the ability to exercise significant control over the lower software and hardware levels. IC serve as the underlying software tools employed for most ASC problems of interest. Often coupling dozens of physics models into very large, very complex applications, ICs are usually the product of hundreds of staff-years of development, with lifetimes measured in decades. Thus, emphasis is placed on portability, maintainability and overall performance, with optimization done on the whole rather than on individual parts. The exascale environment must provide a high-level standardized programming model with effective tools and mechanisms for fault detection and remediation. Finally, V&V addresses the infrastructure and methods to facilitate the assessment of code and model suitability for applications, and uncertainty quantification (UQ) methods for assessment and quantification of margins of uncertainty (QMU). V&V employs both PEM and IC, with somewhat differing goals, i.e., parameter studies and error assessments to determine both the quality of the calculation and to estimate expected deviations of simulations from experiments. The exascale environment must provide a performance envelope suitable both for capacity calculations (high through-put) and full system capability runs (high performance). Analysis of the results place shared demand on both the I/O as well as the visualization subsystems.

97 MATHEMATICS AND COMPUTING↗

Analysis of Supply Chains and Advanced Manufacturing of Small Hydropower Systems

Clean energy manufacturing is a sector of increasing importance both in the United States and worldwide. In the United States, it has been presented as an engine for job creation in a sector of the U.S. economy that was hit hard by the 2008-2009 recession. The Clean Energy Manufacturing Analysis Center (CEMAC), sponsored by the U.S. Department of Energy (DOE), conducts credible, objective, industry-relevant, recurring, and consistent analyses of clean energy technologies. In this project, the National Renewable Energy Laboratory (NREL) and the Oak Ridge National Laboratory (ORNL) collaborated in a hydropower manufacturing and supply chain analysis primarily for U.S. small hydropower (SHP) market to provide insights on supply chain constraints, manufacturing cost, location factors, and opportunities for hydropower using advanced manufacturing technologies. The goal of the project is to improve understanding of the manufacturing opportunities in the U.S. hydropower supply chain, specific competitive advantages, and factors for manufacturing location decisions for SHP. These insights could be used to inform investment and research strategies, policy, and other decisions that could promote economic growth and strengthen U.S. manufacturing capabilities. The project scope included a design for manufacturing and assembly (DFMA) costs analysis and a levelized cost of electricity (LCOE) sensitivity analysis of modular, representative SHP turbines. A representative SHP system was chosen to be made up of two 5 megawatt (MW) turbines, as these Kaplan style turbines could be useable for many non-powered dams (NPDs) across the U.S. The sensitivity analysis used the Integrated Design and Assessment (IDEA) tool, which has helped highlight the impact of the turbine equipment cost on the potential capital expenditure (CAPEX) and LCOE of the installed, representative system. In addition, the project team analyzed international tradeflows (e.g., export and import of hydropower turbines and the parts used in hydropower systems). As part of this project, hydropower stakeholder interviews were undertaken to help identify insights related to hydropower manufacturing opportunities for U.S. players in SHP, the country-specific manufacturing advantages in the United States and threats, and key factors behind manufacturing location decisions made by the SHP industry. Key opportunities for the US SHP market and industry include: Foreign export markets such as Chile, China, Columbia, India and Japan, have an estimated 71,795 MW of technical potential that could be serviced with SHP installations. Utilization of existing manufacturing capacity and expertise, along with economies of scale benefits, could result in increased global competitiveness through lower investment requirements and component costs, which could lead to increased U.S. strength in the export of SHP systems and components. Technology advances such as modular turbine designs, standardized units for conduit systems, precast systems, and improved powertrain technologies could help reduce costs, particularly for manufacturing a small number of units. The DOE is also exploring modular hydropower designs, which would integrate standard independently-produced components, validated to meet multiple specifications. Using modules in product design simplifies manufacturing activities such as inspection, testing, assembly, and purchasing, may increase economies of scale to lower total system cost. There are significant opportunities for the use of composites and Additive Manufacturing (AM) for hydropower components, when design changes are made to hydropower systems. By taking advantage of the corrosion resistance, light-weighting and structural benefits, composites and AM could help significantly alter hydropower structures and installations.

13 HYDRO ENERGY↗

Hydraulic Testing of the Lost Lake Aquifer Near Recovery Well RWM 8

Groundwater beneath the M-Area HWMF is contaminated with chlorinated ethenes including trichloroethylene (TCE) and tetrachloroethylene (PCE). SRS operates a network of recovery wells designed to hydraulically contain and capture the high concentration VOC plume in the Lost Lake Aquifer Zone (LLAZ) (Figure 1). The recovery wells are connected to the M-1 Air Stripper and the system is permitted by the South Carolina Department of Environmental Control (SCDHEC) to operate at a total flow of 610 gpm. RWM 8, which is one of ten operational recovery wells, has historically operated at a flow rate of approximately 40 gpm. RWM 8 was installed with four separate 10-ft screens that spanned the LLAZ with a continuous gravel pack spaced as shown in Figure 2. The three uppermost screens are located within the LLAZ whereas the deepest screen is located within the middle sand of the Crouch Branch Confining Unit (CBCU). Area Closure Projects (ACP) installed a permanent packer in May 2019 to isolate the lowest screen from the pump with the goal being to target the zone of highest concentration in the LLAZ. ACP expressed concern that a substantial portion of the flow from RWM 8 comes from the lower screen. With this screen isolated from service, flow from the well may be below the desired operational envelope for the well. The reconfiguration of RWM 8 presented an opportunity to re-evaluate the performance characteristics of the well. Following placement of the packer and relocation of the pump, the well was redeveloped. To assess the effects of eliminating the lower screen, a step-drawdown test was planned. The purpose of this test was to establish new baseline well performance properties including specific capacity, well efficiency, and well loss coefficients. Data from the step-drawdown testing was also used to estimate a maximum pumping rate for RWM 8 under the new configuration. The setup for the step-drawdown test facilitated a subsequent constant rate aquifer pumping test aimed at determining aquifer hydraulic properties. Properties estimated for the LLAZ included transmissivity and storativity. Following shutdown of RWM 8, recovery data were also collected and analyzed to estimate aquifer properties. This report discusses the hydrologic tests conducted following the reconfiguration of RWM 8. The information provided in this report may serve as input to subsequent updates to the groundwater flow and contaminant transport model for A/M Area.

42 ENGINEERING↗

Prefeasibility Assessment for Solar PV and Storage for Critical Community Facilities in Chernihiv, Ukraine [Slides]

A prefeasibility analysis is performed for integrating solar photovoltaics and battery energy storage at four critical facilities in Chernihiv, Ukraine. The facilities were identified by Chernihiv city officials and include Hospital No. 2, the Maternity Hospital, Secondary School No. 11, and Preschool No. 4. The analyses were performed using NREL's REopt decision-support software tool. The analysis identifies potential capacities for PV and battery energy storage to provide both economic and resilience benefits. The conceptual architecture and estimates of key summary financial and performance metrics are presented.

14 SOLAR ENERGY↗

Uranium Retardation Capacity of Lithologies from the Negev Desert, Israel—Rock Characterization and Sorption Experiments

A series of batch experiments were performed to assess the uranium sorption capacity of four mineralogically distinct lithologies from the Negev Desert, Israel, to evaluate the suitability of a potential site for subsurface radioactive waste disposal. The rock specimens consisted of an organic-rich phosphorite, a bituminous marl, a chalk, and a sandstone. The sorption data for each lithology were fitted using a general composite surface complexation model (GC SCM) implemented in PHREEQC. Sorption data were also fitted by a non-mechanistic Langmuir sorption isotherm, which can be used as an alternative to the GC SCM to provide a more computationally efficient method for uranium sorption. This is because all the rocks tested have high pH/alkalinity/calcium buffering capacities that restrict groundwater chemistry variations, so that the use of a GC SCM is not advantageous. The mineralogy of the rocks points to several dominant sorption phases for uranyl (UO 2 2+ ), including apatite, organic carbon, clays, and iron-bearing phases. The surface complexation parameters based on literature values for the minerals identified overestimate the uranium sorption capacities, so that for our application, an empirical approach that makes direct use of the experimental data to estimate mineral-specific sorption parameters appears to be more practical for predicting uranium sorption.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Assessment of canopy chlorophyll content retrieval in maize and soybean: Implications of hysteresis on the development of generic algorithms

Here, canopy chlorophyll content (Chl) closely relates to plant photosynthetic capacity, nitrogen status and productivity. The goal of this study is to develop remote sensing techniques for accurate estimation of canopy Chl during the entire growing season without re-parameterization of algorithms for two contrasting crop species, maize and soybean. These two crops represent different biochemical mechanisms of photosynthesis, leaf structure and canopy architecture. The relationships between canopy Chl and reflectance, collected at close range and resampled to bands of the Multi Spectral Instrument (MSI) aboard Sentinel-2, were analyzed in samples taken across the entirety of the growing seasons in three irrigated and rainfed sites located in eastern Nebraska between 2001 and 2005. Crop phenology was a factor strongly influencing the reflectance of both maize and soybean. Substantial hysteresis of the reflectance vs. canopy Chl relationship existed between the vegetative and reproductive stages. The effect of the hysteresis on vegetation indices (VI), applied for canopy Chl estimation, depended on the bands used and their formulation. The hysteresis greatly affected the accuracy of canopy Chl estimation by widely-used VIs with near infrared (NIR) and red reflectance (e.g., normalized difference vegetation index (NDVI), enhanced vegetation index (EVI) and simple ratio (SR)). VIs that use red edge and NIR bands (e.g., red edge chlorophyll index (CIred edge), red edge NDVI and the MERIS terrestrial chlorophyll index (MTCI)) were minimally affected by crop phenology (i.e., they exhibited little hysteresis) and were able to accurately estimate canopy Chl in two crops without algorithm re-parameterization and, thus, were found to be the best candidates for generic algorithms to estimate crop Chl using the surface reflectance products of MSI Sentinel-2.

59 BASIC BIOLOGICAL SCIENCES↗

Potential Impact of Interfacial Bonding Efficiency on High-Burnup Spent Nuclear Fuel Vibration Integrity during Normal Transportation

Finite element analysis (FEA) was used to investigate the impacts of interfacial bonding efficiency at pellet pellet and pellet clad interfaces on spent nuclear fuel (SNF) vibration integrity. The FEA simulation results were also validated and benchmarked with reverse bending fatigue test results on surrogate rods consisting of stainless steel (SS) tubes with alumina-pellet inserts. Bending moments (M) are applied to the FEA models to evaluate the system responses of the surrogate rods. From the induced curvature, , the flexural rigidity EI can be estimated as EI=M/ . The impacts of interfacial bonding efficiency on SNF vibration integrity include the moment carrying capacity distribution between pellets and clad and the impact of cohesion on the flexural rigidity of the surrogate rod system. The result also indicates that the immediate consequences of interfacial de-bonding are a load carrying capacity shift from the fuel pellets to the clad and a reduction of the composite rod flexural rigidity. Therefore, the flexural rigidity of the surrogate rod and the bending moment bearing capacity between the clad and fuel pellets are strongly dependent on the efficiency of interfacial bonding at the pellet pellet and pellet clad interfaces. The above-noted phenomenon was calibrated and validated by reverse bending fatigue testing using a surrogate rod system.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

A Multi-Objective, Hub-and-Spoke Supply Chain Design Model For Densified Biomass

In this paper we propose a model to design the supply chain for densified biomass. Rail is typically used for long-haul, high-volume shipment of densified biomass. This is the reason why a hub-and-spoke network structure is used to model this supply chain. The model is formulated as a multi-objective, mixed-integer programing problem under economic, environmental, and social criteria. The goal is to identify the feasibility of meeting the Renewable Fuel Standard (RFS) by using biomass for production of cellulosic ethanol. The focus in not just on the costs associated with meeting these standards, but also exploring the social and environmental benefits that biomass production and processing offers by creating new jobs and reducing greenhouse gas (GHG) emissions. We develop an augmented ?-constraint method to find the exact Pareto solution to this optimization problem. We develop a case study using data from the Mid-West. The model identifies the number, capacity and location of biorefineries needed to make use of the biomass available in the region. The model estimates the delivery cost of cellulosic ethanol under different scenario, the number new jobs created and the GHG emission reductions in the supply chain.

09 BIOMASS FUELS↗