Results for “Configuration” — Page 43

NASA NTRS2023

Development of Two High-Energy Bus ‘Cores’ for Rapid Support of Low-TRL and Educational Payloads: A Software-Configured EPS Combined with Flexible C&DH

For several years the TechEdSat flight series (TES-n), developed by the Nano Orbital Workshop (NOW) group at NASA Ames, has relied upon an in-house developed unit to serve both EPS (Electrical Power System) and C&DH (Command and Data Handling) roles along with low data-rate telemetry functions, i.e., serving as the ‘core’ of the spacecraft bus. This ‘core’ has a considerable task given the rapid cadence of the TES program and the typically low-TRL of payloads; configurability and compatibility are key to prevent mission-specific hardware. However, at only 15 watts the current core has become insufficient to support the program’s growing missions and increasingly demanding payloads. To this end, the NOW program is developing new cores to support two TES mission classes: a single-PCB ‘MiniCore’ designed to support 80-watt missions 6U or smaller in LEO, and a three-PCB, radiation-tolerant ‘StackCore’ designed to support 6U and larger missions over 500 watts in LEO and beyond. The ‘MiniCore’ design consists of three main segments: a processor-agnostic C&DH, a software-configured EPS, and a backup low data-rate radio. The design philosophy was to enable rapid-manufacture in a turbulent supply chain, hence the design consists of COTS parts with a focus on those able to be drop-in replaced with radiation-tolerant versions when demanded by the mission. As a single PC-104 sized circuit board, power density and ease of integration also dominated design, demanding the use of modern features such as single-point USB-C for easy charging and monitoring of the spacecraft on the ground. The ‘MiniCore’ can support 80 watts of load, 140 watt-hours of storage, and over 20 watts of optimized solar generation with extensive power monitoring throughout. The ‘MiniCore’ supports one battery pack, six solar-panels, six loads, five actuators, Iridium SBD, and an internal 802.15.4 network. Additionally, the processor-agnostic design can accept any PJRC Teensy 3.x or Adafruit Feather microcontroller unit to enable processor scaling with mission requirements or environment. It is expected a development unit of this design will be completed before conference. The ‘StackCore’ design consists of three stacked PC-104 sized circuit boards: one dedicated to power generation and storage, one dedicated to power distribution, and one dedicated to C&DH tasks. This delineation is necessary to support the transition from highly integrated ICs to discrete analog circuitry, enabling a primarily analog control power system able to operate without software in a radiation environment with finer monitoring compared to the ‘MiniCore’ design. The planned base architecture supports over 500 watts of load, 250 watt-hours of storage, and over 80 watts of optimized solar generation. The power distribution board allows for the use of daughter cards hosting custom converters or interfaces for payloads, in addition to the software-configured supplies used on the ‘MiniCore’. This core stack will be managed by a Vorago ARM M4 microcontroller and support the same wireless communications as the ‘MiniCore’, with optional integration of a NOW S-band radio and attitude determination sensors for ‘black box’ functionality. It is expected the prototype will still be in development during conference.

Spacecraft↗

NASA NTRSDate not supplied

Development of Two High-Energy Bus ‘Cores’ for Rapid Support of Low-TRL and Educational Payloads: A Software-Configured EPS Combined with Flexible C&DH

For several years the TechEdSat flight series (TES-n), developed by the Nano Orbital Workshop (NOW) group at NASA Ames, has relied upon an in-house developed unit to serve both EPS (Electrical Power System) and C&DH (Command and Data Handling) roles along with low data-rate telemetry functions, i.e., serving as the ‘core’ of the spacecraft bus. This ‘core’ has a considerable task given the rapid cadence of the TES program and the typically low-TRL of payloads; configurability and compatibility are key to prevent mission-specific hardware. However, at only 15 watts the current core has become insufficient to support the program’s growing missions and increasingly demanding payloads. To this end, the NOW program is developing new cores to support two TES mission classes: a single-PCB ‘MiniCore’ designed to support 80-watt missions 6U or smaller in LEO, and a three-PCB, radiation-tolerant ‘StackCore’ designed to support 6U and larger missions over 500 watts in LEO and beyond. The ‘MiniCore’ design consists of three main segments: a processor-agnostic C&DH, a software-configured EPS, and a backup low data-rate radio. The design philosophy was to enable rapid-manufacture in a turbulent supply chain, hence the design consists of COTS parts with a focus on those able to be drop-in replaced with radiation-tolerant versions when demanded by the mission. As a single PC-104 sized circuit board, power density and ease of integration also dominated design, demanding the use of modern features such as single-point USB-C for easy charging and monitoring of the spacecraft on the ground. The ‘MiniCore’ can support 80 watts of load, 140 watt-hours of storage, and over 20 watts of optimized solar generation with extensive power monitoring throughout. The ‘MiniCore’ supports one battery pack, six solar-panels, six loads, five actuators, Iridium SBD, and an internal 802.15.4 network. Additionally, the processor-agnostic design can accept any PJRC Teensy 3.x or Adafruit Feather microcontroller unit to enable processor scaling with mission requirements or environment. It is expected a development unit of this design will be completed before conference. The ‘StackCore’ design consists of three stacked PC-104 sized circuit boards: one dedicated to power generation and storage, one dedicated to power distribution, and one dedicated to C&DH tasks. This delineation is necessary to support the transition from highly integrated ICs to discrete analog circuitry, enabling a primarily analog control power system able to operate without software in a radiation environment with finer monitoring compared to the ‘MiniCore’ design. The planned base architecture supports over 500 watts of load, 250 watt-hours of storage, and over 80 watts of optimized solar generation. The power distribution board allows for the use of daughter cards hosting custom converters or interfaces for payloads, in addition to the software-configured supplies used on the ‘MiniCore’. This core stack will be managed by a Vorago ARM M4 microcontroller and support the same wireless communications as the ‘MiniCore’, with optional integration of a NOW S-band radio and attitude determination sensors for ‘black box’ functionality. It is expected the prototype will still be in development during conference.

Spacecraft↗

NASA NTRSDate not supplied

Autonomous Constrained Control for Arbitrary Configurations of Gimbaling Thrusters in SE(3)

In order to develop robust autonomy in spacecraft, it is desirable to develop methods for controlling a spacecraft in various configurations with any combination of thrusters of various types and both for static RCS thrusters and gimbaling thrusters. In the case of a stuck thruster imposing unplanned and undesired motion both translational and rotational or in the case of a malfunctioning thruster, it is desirable for that spacecraft to have the ability to identify and overcome that problem without human intervention. To that end, a spacecraft must be able to rapidly and autonomously reconfigure thruster firing histories and update guidance protocols. In this paper, a method for a spacecraft to autonomously select thrusters of any configuration is presented. The residual motion imposed by off-nominal or not-fully-controllable thruster configurations is identified by the spacecraft and solved for, both for static reaction control systems and gimbaling engines.

Matthew M. Witta↗

NASA NTRSDate not supplied

CFD Validation Study of a Hypersonic Cone-Slice-Flap Variable Geometry Configuration

Model validation is the process of determining the degree of accuracy between physical reality and the model. The result of model validation can either be used to improve the model through calibration or quantify the model-form uncertainty. This work focuses on providing the model-form uncertainty through an area metric for a hypersonic cone-slice-flap variable geometry configuration given uncertainty in both the simulation and experimental data. The research here compares two different turbulence models for the simulations. For a variable geometry, performing uncertainty quantification to capture the model-form uncertainty on every configuration is computationally challenging. This work lays out a procedure that can give an accurate representation of the model-form uncertainty using a small number of high-fidelity runs and many low-fidelity runs on multiple configurations. Running this comparison provides a quantifiable measurement for the accuracy of each turbulence model for this type of design. The high-fidelity CFD solver used was VULCAN-CFD and the low-fidelity results came from Cart3D. The experimental data came from the 20-Inch Mach 6 Tunnel located at NASA Langley Research Center. The present work showed that the using both the Spalart and Allamaras and Menter Shear-Stress Transport turbulence models overpredicted the drag and lift coefficient, while underpredicting the pitching moment coefficient. The model-form uncertainty estimate resulted in up to a 13.6% change in the total uncertainty for the drag coefficient, up to a 57.4% change in total uncertainty for the lift coefficient, and up to a 100% change in total uncertainty for the pitching moment coefficient.

Laura M. White↗

NASA NTRSDate not supplied

CFD Validation Study of a Hypersonic Cone-Slice-Flap Variable Geometry Configuration

Model validation is the process of determining the degree of accuracy between physical reality and the model. The result of model validation can either be used to improve the model through calibration or quantify the model-form uncertainty. This work focuses on providing the model-form uncertainty through an area metric for a hypersonic cone-slice-flap variable geometry configuration given uncertainty in both the simulation and experimental data. For a variable geometry, performing uncertainty quantification to capture the model-form uncertainty on every configuration is computationally challenging. This work lays out a procedure that can give an accurate representation of the model-form uncertainty using a small number of high-fidelity runs and many low-fidelity runs on multiple configurations. Running this comparison provides a quantifiable measurement for the accuracy of each turbulence model for this type of design. The high-fidelity CFD solver used was VULCAN-CFD and the low-fidelity results came from Cart3D. The experimental data came from the 20-Inch Mach 6 Tunnel located at NASA Langley Research Center. The present work showed that the turbulence simulation overpredicted the drag and lift coefficient, while underpredicting the pitching moment coefficient. The model-form uncertainty estimate resulted up to a 13.6% change in the total uncertainty for the drag coefficient, up to a 57.4% change in total uncertainty for the lift coefficient, and up to a 100% change in total uncertainty for the pitching moment coefficient.

Laura White↗

NASA NTRS2023

Tensor-to-scalar ratio forecasts for extended LiteBIRD frequency configurations

LiteBIRD is a planned JAXA-led cosmic microwave background (CMB) B -mode satellite experiment aiming for launch in the late 2020s, with a primary goal of detecting the imprint of primordial inflationary gravitational waves. Its current baseline focal-plane configuration includes 15 frequency bands between 40 and 402 GHz, fulfilling the mission requirements to detect the amplitude of gravitational waves with the total uncertainty on the tensor-to-scalar ratio, δr , down to δr < 0.001. A key aspect of this performance is accurate astrophysical component separation, and the ability to remove polarized thermal dust emission is particularly important. In this paper we note that the CMB frequency spectrum falls off nearly exponentially above 300 GHz relative to the thermal dust spectral energy distribution, and a relatively minor high frequency extension can therefore result in even lower uncertainties and better model reconstructions. Specifically, we compared the baseline design with five extended configurations, while varying the underlying dust modeling, in each of which the High-Frequency Telescope (HFT) frequency range was shifted logarithmically toward higher frequencies, with an upper cutoff ranging between 400 and 600 GHz. In each case, we measured the tensor-to-scalar ratio r uncertainty and bias using both parametric and minimum-variance component-separation algorithms. When the thermal dust sky model includes a spatially varying spectral index and temperature, we find that the statistical uncertainty on r after foreground cleaning may be reduced by as much as 30–50% by extending the upper limit of the frequency range from 400 to 600 GHz, with most of the improvement already gained at 500 GHz. We also note that a broader frequency range leads to higher residuals when fitting an incorrect dust model, but also it is easier to discriminate between models through higher χ 2 sensitivity. Even in the case in which the fitting procedure does not correspond to the underlying dust model in the sky, and when the highest frequency data cannot be modeled with sufficient fidelity and must be excluded from the analysis, the uncertainty on r increases by only about 5% for a 500 GHz configuration compared to the baseline.

U. Fuskeland↗

NASA NTRSDate not supplied

Autonomous Constrained Control for Arbitrary Thruster Configurations of Gimbaling Thrusters in SE(3)

In order to develop robust autonomy in spacecraft, it is desirable to develop methods for guiding and controlling arbitrarily-configured spacecraft with any combination of thrusters of various types, i.e. either static reaction control system thrusters and gimbaling thrusters. Scenarios in which autonomous selection of thrusters may be needed include the case of a stuck or inhibited thruster that restricts the motion of the vehicle, vehicles with changing mass properties such as logistics modules or tugs, or vehicles that have imposed constraints on thrusters during docking in order to avoid plume impingement on a space station or adjacent spacecraft. To that end, a spacecraft must be able to rapidly and autonomously reconfigure thruster firing histories and update guidance protocols in accordance with newly imposed constraints. In this paper, a methodology is presented that enables a spacecraft to autonomously select thrusters of any configuration and type in order to optimally match a desired 6-degree-of-freedom navigation and control within the special Euclidean SE(3) framework. The residual motion imposed by off-nominal thruster configurations or thrusters that are not fully controllable is identified by the spacecraft and solved for over time, both for static reaction control systems and for the case of gimbaling thrusters.

GN&C↗

NASA NTRSDate not supplied

Comparison of Alternative Configurations of an Integrated Open-Loop Carbon Dioxide Removal System using Liquid Amine

Several carbon dioxide removal systems are being investigated for applications in microgravity. The liquid amine wedge system utilizes the capillary action of liquids to prevent the mixing of the air and liquid while still allowing for carbon dioxide capture at their interface. A one crew mission requires approximately 1 kg per day of carbon dioxide removal to prevent adverse health effects. A proposed design of a wedge tray system can be improved from the initial testing parameters to achieve the required carbon dioxide capture for one crew. The wedge trays in the contactor can be organized in either a parallel configuration to accumulate less CO2 in the liquid but at a higher flow rate or a series configuration to yield a higher weight percentage of CO2 in the liquid but at a lower flow rate. The gas flow rate and composition were held constant at 26scfm and 2600ppm, respectively, due to constraints of other proposed systems but the liquid flow rate was adjusted between 0.1mL/min and 10mL/min. The flow rate that yielded the best carbon dioxide capture was X mL/min and Y mL/min for the parallel and series configurations, respectively. The degasser temperature and pressure were varied from 80 to 100°C and 0 and -3 inHg. The largest carbon dioxide flux of Z kg/day/m2 was observed at a contactor liquid flow rate of X mL/min and a degasser temperature and pressure of T°C and P inHg.

Adrian Cortez↗

NASA NTRSDate not supplied

Evaluating Lunar Water Processing System Model Configurations for Small Scale Oxygen and Hydrogen Production Within JAXA'S ISRU Technology

Introduction: In-Situ Resource Utilization (ISRU) refers to novel methods of extracting and processing local resources for use in life support and propulsion systems, reducing or eliminating the required consumables to be transferred from Earth. Current estimates of water-ice availability embedded in regolith within the Moon’s permanently shadowed regions (PSR’s) range between 1-5% by weight. However, the composition and characteristics of the “wet” regolith is unknown. Alternate ISRU excavation techniques and Concept of Operations (ConOps) must be explored to optimize surface system operations based on these factors. To assess the feasibility of different ISRU subsystem technologies and compare system architecture configurations, an interchangeable system model was generated to incorporate technologies spanning excavation of raw materials to storage of products and determine optimal arrangement of total system processing needs. Total Mass, Volume, and Power (M/V/P) requirements were computed for 168 design iterations of this water processing plant. System Model: In FY24, the System Engineering and Integration (SE&I) ISRU Modeling and Analysis (SIMA) team developed a lunar water processing system model using the Mission Analysis and Integration Tool (MAIT) to estimate the M/V/P for ISRU subsystems operating under a wide range of Hydrogen (H2) and Oxygen (O2) production targets for the Space Technology Mission Directorate (STMD) [1]. Based on Japan Aerospace Exploration Agency’s (JAXA) surface operational requirements, this system architecture was modified to include the ability to excavate consolidated icy regolith (versus granular ice excavation using Kennedy Space Center’s (KSC) ISRU Pilot Excavator, IPEx) and explore the feasibility of processing the lunar water both inside and outside of the PSR. For the consolidated icy regolith case study, excavation was performed via a mobility transport chassis outfitted with The Regolith Ice Drill for Exploring New Terrain (TRIDENT) for drilling [2] and the Cold Operable Lunar Deployable Arm (COLDArm) [3] for regolith transfer. The system model determines the required rover and payload. M/V/P to handle the required regolith processing rates. The regolith is then sorted and heated to sublimate the ice (via an auger dryer). The exiting high temperature, low pressure vapor is cleaned of volatiles (via cold trap) and electrolyzed to produce H2 and O2. These products are then dried, liquified with 20 K and 90 K cryocoolers (for H2 and O2, respectively), and stored in cylindrical tanks. Study Goals: Due to the different ConOps options of regolith transport to the ridge for processing versus processing it directly inside the PSR, as well as the unknown regolith/water-ice composition, new excavation techniques and their power configurations are being evaluated within a ISRU system architecture for production targets less than NASA’s pilot plant (1 mT). This analysis investigates the feasibility of numerous excavation techniques, power architectures, and logistical operations and determines an optimal system configuration with regards to M/V/P. It aims to investigate which parameters, both locally and globally, have the greatest effect on each subsystem within the plant. This can be used to identify the most critical components of the plant, and guide future decisions on allocating funding for research and development. The results from this study may provide subsystem developers with appropriate interfaces with excavation subsystems and downstream processes, and assessing the overall feasibility of each excavation technique, power architecture, and logistical timeframe. References: [1] Carlson, A. et. al. (2024) ICES. [2] Zacny, K., et. al. (2024) “ASCE Earth and Space”. [3] McCormick, R., et. Al. (2024) IEEE Xplore.

ISRU↗

NASA NTRSDate not supplied

High Reynolds Number Testing of the NATO AVT-298 SWiFT Configuration at the National Transonic Facility

A high Reynolds number wind tunnel test of the NATO AVT-298 Swept Wing Flow Test (SWiFT) configuration was conducted in the National Transonic Facility at the NASA Langley Research Center during the summer of 2023. The SWiFT research model geometry has relevance to both blended/hybrid wing body (BWB/HWB) and unmanned combat aerial vehicle (UCAV) configurations, and the test campaign was the culmination of an international collaboration under the NATO AVT-298 research task group. The main objectives of the test were to investigate Reynolds number scaling effects on low-speed stability & control characteristics and to examine the onset and progression of flow separation on the wings particularly near the wing crank. Force & moment and surface pressure data were acquired at Mach numbers from 0.2 to 0.8, Reynolds numbers from 2.5 to 34 million, angles of attack from -3 to 20 degrees, and sideslip angles from -10 to 10 degrees. Boundary layer transition detection techniques utilizing static pressure taps, unsteady pressure transducers, and sublimating chemicals were used on the model in a free/natural transition state or a forced transition state using trip dots. Pressure sensitive paint was used to obtain a global surface pressure profile on the model and an advanced laser velocimetry technique was used to obtain velocity measurements in the wake downstream of the wing crank. The results from the test showed clear Reynolds number scaling effects on the maximum lift coefficient and pitching moment coefficient at Mach 0.2, while also capturing significant hysteresis effects. The data acquired from the test will ultimately help improve computational aerodynamic analysis and design tools for application to future BWB-type vehicle configurations.

NATO AVT-298↗

NASA NTRSDate not supplied

High Reynolds Number Testing of the NATO AVT-298 SWiFT Configuration at the National Transonic Facility

A high Reynolds number wind tunnel test of the NATO AVT-298 Swept Wing Flow Test (SWiFT) configuration was conducted in the National Transonic Facility at the NASA Langley Research Center during the summer of 2023. The SWiFT research model geometry has relevance to both blended/hybrid wing body (BWB/HWB) and unmanned combat aerial vehicle (UCAV) configurations, and the test campaign was the culmination of an international collaboration under the NATO AVT-298 research task group. The main objectives of the test were to investigate Reynolds number scaling effects on low-speed stability & control characteristics and to examine the onset and progression of flow separation on the wings particularly near the wing crank. Force & moment and surface pressure data were acquired at Mach numbers from 0.2 to 0.8, Reynolds numbers from 2.5 to 34 million, angles of attack from -3 to 20 degrees, and sideslip angles from -10 to 10 degrees. Boundary layer transition detection techniques utilizing static pressure taps, unsteady pressure transducers, and sublimating chemicals were used on the model in a free/natural transition state or a forced transition state using trip dots. Pressure sensitive paint was used to obtain a global surface pressure profile on the model and an advanced laser velocimetry technique was used to obtain velocity measurements in the wake downstream of the wing crank. The results from the test showed clear Reynolds number scaling effects on the maximum lift coefficient and pitching moment coefficient at Mach 0.2, while also capturing significant hysteresis effects. The data acquired from the test will ultimately help improve computational aerodynamic analysis and design tools for application to future BWB-type vehicle configurations.

BWB/HWB↗

DOE OSTI2020

Portable generator having a configurable load bank

A portable generator includes a combustion engine. The portable generator includes an electric generator coupled to the combustion engine. The portable generator can include a load bank. When the electric generator operates at a first voltage and generates less than a threshold amount, the load bank is coupled to the electric generator in a first configuration. When the electric generator operates at a second voltage that is different than the first voltage, the load bank is coupled to the electric generator in a second configuration that is different than the first configuration.

42 ENGINEERING↗

DOE OSTI2020

Halbach-array levitating passive magnetic bearing configuration

Novel configurations of levitating passive magnetic bearing configurations are described. Such configurations can be used for the precise control of the magnitude and sign of the bearing stiffness, thereby facilitating the overall design of the system in ways that are not possible with conventional attractive or repelling bearing elements.

Post, Richard F.↗

DOE OSTI2021

Experiment Simulation Configurations Approximating DUNE TDR

The Deep Underground Neutrino Experiment (DUNE) is a next-generation long-baseline neutrino oscillation experiment consisting of a high-power, broadband neutrino beam, a highly capable near detector located on site at Fermilab, in Batavia, Illinois, and a massive liquid argon time projection chamber (LArTPC) far detector located at the 4850L of Sanford Underground Research Facility in Lead, South Dakota. The long-baseline physics sensitivity calculations presented in the DUNE Physics TDR, and in a related physics paper, rely upon simulation of the neutrino beam line, simulation of neutrino interactions in the near and far detectors, fully automated event reconstruction and neutrino classification, and detailed implementation of systematic uncertainties. The purpose of this posting is to provide a simplified summary of the simulations that went into this analysis to the community, in order to facilitate phenomenological studies of long-baseline oscillation at DUNE. Simulated neutrino flux files and a GLoBES configuration describing the far detector reconstruction and selection performance are included as ancillary files to this posting. A simple analysis using these configurations in GLoBES produces sensitivity that is similar, but not identical, to the official DUNE sensitivity. DUNE welcomes those interested in performing phenomenological work as members of the collaboration, but also recognizes the benefit of making these configurations readily available to the wider community.

Abi, B↗

DOE OSTI2022

System and method for reasoning about the optimality of a configuration parameter of a distributed system

Embodiments provide a system and method for reasoning about the optimality of a configuration parameter of a distributed system. During operation, the system obtains a multi-layer graph for a system with a plurality of components, wherein the multi-layer graph comprises a configuration subgraph, a vulnerability subgraph, and a dependency subgraph. The system determines, based on the multi-layer graph, constraint relationships associated with configuration parameters for the components, wherein the constraint relationships include security constraints and functionality constraints. The system computes an unsatisfiable core which comprises a set of mutually incompatible constraints. The system resolves, based on a strategy and over multiple iterations, the unsatisfiable core by analyzing one pair of mutually incompatible constraints per a respective iteration, to obtain a new unsatisfiable core which comprises a smaller number of mutually incompatible constraints than the computed unsatisfiable core or a previously computed unsatisfiable core from a most recent iteration.

Soroush, Hamed↗

DOE OSTI2024

The Prompt Fission Uranium Neutron Spectrum (PFUNS) Experiment: Critical Configurations and Irradiations

The objective of the Prompt Fission Uranium Neutron Spectrum (PFUNS) experiment is to reduce the uncertainty of the Prompt Fission Neutron Spectrum (PFNS) of 235 U above 8 MeV. The experiment was performed at the DOE National Criticality Experiments Research Center (NCERC) at the Nevada National Security Site. To meet the experiment objective, activation foils were placed in a central void region of a critical configuration consisting of concentric highly enriched uranium (HEU) metal hemishells. The set of activation foils were chosen based on threshold reactions to neutron energies across the fission spectrum, but especially those in the high energy tail of the fission spectrum. PFUNS was performed on the Planet critical assembly machine at NCERC and uses the Rocky Flats (RF) HEU hemishells. PFUNS has similarities to the Measurement of Uranium Subcritical and Critical (MUSiC) experiment conducted at NCERC in 2021, which also used RF hemishells, but contains a large central cavity to allow for a sample plate to be inserted. This large void means that much more HEU is needed to achieve a critical configuration (108 kg for PFUNS versus 59 kg for MUSiC). This work describes the 2024 experiment execution of four critical configurations and two irradiations for the PFUNS project.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

NASA NTRS1988

AGARD standard aeroelastic configurations for dynamic response. 1: Wing 445.6

This report contains experimental flutter data for the AGARD 3D swept tapered standard configuration "Wing 445.6", along with related descriptive data of the model properties required for comparative flutter calculations. As part of a cooperative AGARD-SMP programme, guided by the Sub-Committee on Aeroelasticity, this standard configuration may serve as a common basis for comparisons of calculated and measured aeroelastic behaviour. These comparisons will promote a better understanding of the assumptions, approximations and limitations underlying the various aerodynamic methods applied, thus pointing the way to further improvements.

Aircraft↗

DOE OSTI2023

The Princeton Field-Reversed Configuration for Compact Nuclear Fusion Power Plants

The Princeton Field-Reversed Configuration (PFRC) nuclear fusion reactor concept is an innovative approach to fusion power generation prioritizing low neutron production and small size. Here, a combination of analytical modeling and numerical simulation shows that the novel heating approach generates an FRC with closed field lines. Simulation data from a single-particle Hamiltonian code predicts ms-scale plasma heating in reactor-scale conditions while PIC codes predict formation of warm FRC plasmas from initial mirror fields. The PFRC-1 and PFRC-2 experiments have heated electrons to energies well in excess of 100 eV and plasma durations to 300 ms, more than 10 4 times longer than the predicted tilt instability growth time. From these data, we have created a development plan and anticipated performance metrics for a fusion reactor based on the PFRC concept. The resulting 1–10 MW PFRC reactors would be suitable for diverse applications, from submarines to urban environments to space propulsion. PFRC is a steady-state, driven magnetic confinement device. Plasma, inside a cylindrical array of coils, is confined and heated by external RF antennae. PFRC would be ultra-low radiation due to both its fuel and small size. The choice of advanced fuels, deuterium and helium-3 (D– 3 He), may be enabled by the high-β FRC configuration. The small size of the reactor would enable rapid exhaust of the dangerous tritium ash. Low radiation would make the reactor safer to operate and, in combination with simple geometry and small size, dramatically lowers development and maintenance costs. This review paper gives an introduction to the physics of the PFRC and a summary of the PFRC-2 experiment results to date. It then discusses the future program plan and how PFRC reactors would be commercialized.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗