Search NASA⌕ Search

SEARCH · Search NASA

Results for “DECELERATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

Accelerations and Passenger Harness Loads Measured in Full-Scale Light-Airplane Crashes

Full-scale light-airplane crashes simulating stall-spin accidents were conducted to determine the decelerations to which occupants are exposed and the resulting harness forces encountered in this type of accident. Crashes at impact speeds from 42 to 60 miles per hour were studied. The airplanes used were of the familiar steel-tube, fabric-covered, tandem, two-seat type. In crashes up to an impact speed of 60 miles per hour, crumpling of the forward fuselage structure prevented the maximum deceleration at the rear-seat location from exceeding 26 to 33g. This maximum g value appeared independent of the impact speed. Restraining forces in the seatbelt - shoulder-harness combination reached 5800 pounds. The rear-seat occupant can survive crashes of the type studied at impact speeds up to 60 miles per hour, if body movement is restrained by an adequate seatbelt-shoulder-harness combination so as to prevent injurious contact with obstacles normally present in the cabin. Inwardly collapsing cabin structure, however, is a potential hazard in the higher-speed crashes.

Eiband, A. Martin↗

A study of the torque equilibrium of an autogiro rotor

Two improvements have been made in the method developed in NACA Reports nos. 487 and 591 for the estimation of the inflow velocity required to overcome a given decelerating torque in an autogiro rotor. At low tip-speed ratios, where the assumptions necessary for the analytical integrations of the earlier papers are valid, the expressions therein derived are greatly simplified by combining and eliminating terms with a view of minimizing the numerical computations required. At high tip-speed ratios, by means of charts based on graphical integrations, errors inherent in the assumptions associated with the analytical method are largely eliminated. The suggested method of estimating the inflow velocity presupposes a knowledge of the decelerating torque acting on the rotor; all available full-scale experimental information on this subject is included.

Bailey, F J , Jr↗

Attainable circulation about airfoils in cascade

From consideration of available information on boundary-layer behavior, a relation among profile thickness, maximum surface velocity, Reynolds number, velocity diagram, and solidity is established for a cascade of airfoils immersed in a two-dimensional incompressible fluid flow. Several cascades are computed to show the effect of various cascade design parameters on minimum required cascade solidity. Comparisons with experimentally determined blade performance show that the derived blade loadings are equal or higher for moderate flow deceleration and somewhat lower for large deceleration. Blades with completely laminar flow appear practical for impulse or reaction blading.

Goldstein, Arthur W↗

Correcting For Seed-Particle Lag In LV Measurements

Two experiments conducted to evaluate effects of sizes of seed particles on errors in LV measurements of mean flows. Both theoretical and conventional experimental methods used to evaluate errors. First experiment focused on measurement of decelerating stagnation streamline of low-speed flow around circular cylinder with two-dimensional afterbody. Second performed in transonic flow and involved measurement of decelerating stagnation streamline of hemisphere with cylindrical afterbody. Concluded, mean-quantity LV measurements subject to large errors directly attributable to sizes of particles. Predictions of particle-response theory showed good agreement with experimental results, indicating velocity-error-correction technique used in study viable for increasing accuracy of laser velocimetry measurements. Technique simple and useful in any research facility in which flow velocities measured.

Jones, Gregory S.↗

Project Longshot

Project Longshot is an unmanned probe to our nearest star system, Alpha Centauri, 4.3 light years away. The Centauri system is a trinary system consisting of two central stars (A and B) orbiting a barycenter, and a third (Proxima Centauri) orbiting the two. The system is a declination of -67 degrees. The goal is to reach the Centauri system in 50 years. This time space was chosen because any shorter time would be impossible of the relativistic velocities involved, and any greater time would be impossible because of the difficulty of creating a spacecraft with such a long lifetime. Therefore, the following mission profile is proposed: (1) spacecraft is assembled in Earth orbit; (2) spacecraft escapes Earth and Sun in the ecliptic with a single impulse maneuver; (3) spacecraft changed declination to point toward Centauri system; (4) spacecraft accelerates to 0.1c; (5) spacecraft coasts at 0.1c for 41 years; (6) spacecraft decelerates upon reaching Centauri system; and (7) spacecraft orbits Centauri system, conducts investigations, and relays data to Earth. The total time to reach the Centauri system, taking into consideration acceleration and deceleration, will be approximately 50 years.

West, J. Curtis↗

Electric propulsion system technology

The work performed in fiscal year (FY) 1991 under the Propulsion Technology Program RTOP (Research and Technology Objectives and Plans) No. (55) 506-42-31 for Low-Thrust Primary and Auxiliary Propulsion technology development is described. The objectives of this work fall under two broad categories. The first of these deals with the development of ion engines for primary propulsion in support of solar system exploration. The second with the advancement of steady-state magnetoplasmadynamic (MPD) thruster technology at 100 kW to multimegawatt input power levels. The major technology issues for ion propulsion are demonstration of adequate engine life at the 5 to 10 kW power level and scaling ion engines to power levels of tens to hundreds of kilowatts. Tests of a new technique in which the decelerator grid of a three-grid ion accelerator system is biased negative of neutralizer common potential in order to collect facility induced charge-exchange ions are described. These tests indicate that this SAND (Screen, Accelerator, Negative Decelerator) configuration may enable long duration ion engine endurance tests to be performed at vacuum chamber pressures an order of magnitude higher than previously possible. The corresponding reduction in pumping speed requirements enables endurance tests of 10 kW class ion engines to be performed within the resources of existing technology programs. The results of a successful 5,000-hr endurance of a xenon hollow cathode operating at an emission current of 25 A are described, as well as the initial tests of hollow cathodes operating on a mixture of argon and 3 percent nitrogen. Work performed on the development of carbon/carbon grids, a multi-orifice hollow cathode, and discharge chamber erosion reduction through the addition of nitrogen are also described. Critical applied-field MPD thruster technical issues remain to be resolved, including demonstration of reliable steady-state operation at input powers of hundreds to thousands of kilowatts, achievement of thruster efficiency and specific impulse levels required for missions of interest, and demonstration of adequate engine life at these input power, efficiency, and specific impulse levels. To address these issues we have designed, built, and tested a 100 kW class, radiation-cooled applied-field MPD thruster and a unique dual-beam thrust stand that enables separate measurements of the applied- and self-field thrust components. We have also initiated the development of cathode thermal and plasma sheath models that will eventually be used to guide the experimental program. In conjunction with the cathode modeling, a new cathode test facility is being constructed. This facility will support the study of cathode thermal behavior and erosion mechanisms, the diagnosis of the near-cathode plasma and the development and endurance testing of new, high-current cathode designs. To facilitate understanding of electrode surface phenomenon, we have implemented a telephoto technique to obtain photographs of the electrodes during engine operation. In order to reduce the background vacuum tank pressure during steady-state engine operation in order to obtain high fidelity anode thermal data, we have developed and are evaluating a gas-dynamic diffuser. A review of experience with alkali metal propellants for MPD thrusters led to the conclusion that alkali metals, particularly lithium, offer the potential for significant engine performance and lifetime improvements. These propellants are also condensible at room temperature, substantially reducing test facility pumping requirements. The most significant systems-level issue is the potential for spacecraft contamination. Subsequent experimental and theoretical efforts should be directed toward verifying the performance and lifetime gains and characterizing the thruster flow field to assess its impact on spacecraft surfaces. Consequently, we have begun the design and development of a new facility to study engine operation with alkali metal propellants.

Brophy, John R.↗

Determination of cosmic bodies size-velocity distribution by observation of current impacts on Mars

Collisions of cosmic bodies with terrestrial planets involve many physical processes such as deceleration and ablation during their flight through an atmosphere, the impact at a surface accompanied by cratering, melting and evaporation of surface material, generation of shock waves, etc. If body velocity is high enough then a thermal radiation is very important. All these processes on Mars proceed differently than on the other planets because of the low density of its atmosphere. In particular, this leads to the fact that smaller bodies of sizes of the order of 0.1-10 m strike the planet surface without being decelerated and perform some effects which may be detected by equipment placed on a board of artificial satellites, by a network of stations at the surface of Mars and even from the Earth. These observations can be used to determine size-velocity distribution of such bodies in the Solar System. Numerical simulation of the impacts at the surface of Mars have been carried out using two-dimensional gas dynamic code with detailed consideration of the thermal radiative transfer. This work is an extension of our previous paper. We have expanded a range of projectile sizes up to r sub 0 = 100 m. For such a large-scale body, the initial stage of the impact, involving crate ring and ejection of surface material, is very important. Thus, these effects have been taken into account.

Nemchinov, I. V.↗

Effects of historical and predictive information on ability of transport pilot to predict an alert

In the aviation community, the early detection of the development of a possible subsystem problem during a flight is potentially useful for increasing the safety of the flight. Commercial airlines are currently using twin-engine aircraft for extended transport operations over water, and the early detection of a possible problem might increase the flight crew's options for safely landing the aircraft. One method for decreasing the severity of a developing problem is to predict the behavior of the problem so that appropriate corrective actions can be taken. To investigate the pilots' ability to predict long-term events, a computer workstation experiment was conducted in which 18 airline pilots predicted the alert time (the time to an alert) using 3 different dial displays and 3 different parameter behavior complexity levels. The three dial displays were as follows: standard (resembling current aircraft round dial presentations); history (indicating the current value plus the value of the parameter 5 sec in the past); and predictive (indicating the current value plus the value of the parameter 5 sec into the future). The time profiles describing the behavior of the parameter consisted of constant rate-of-change profiles, decelerating profiles, and accelerating-then-decelerating profiles. Although the pilots indicated that they preferred the near term predictive dial, the objective data did not support its use. The objective data did show that the time profiles had the most significant effect on performance in estimating the time to an alert.

Trujillo, Anna C.↗

Developing and flight testing the HL-10 lifting body: A precursor to the Space Shuttle

The origins of the lifting-body idea are traced back to the mid-1950's, when the concept of a manned satellite reentering the Earth's atmosphere in the form of a wingless lifting body was first proposed. The advantages of low reentry deceleration loads, range capability, and horizontal landing of a lifting reentry vehicle (as compared with the high deceleration loads and parachute landing of a capsule) are presented. The evolution of the hypersonic HL-10 lifting body is reviewed from the theoretical design and development process to its selection as one of two low-speed flight vehicles for fabrication and piloted flight testing. The design, development, and flight testing of the low-speed, air-launched, rocket-powered HL-10 was part of an unprecedented NASA and contractor effort. NASA Langley Research Center conceived and developed the vehicle shape and conducted numerous theoretical, experimental, and wind-tunnel studies. NASA Flight Research Center (now NASA Dryden Flight Research Center) was responsible for final low-speed (Mach numbers less than 2.0) aerodynamic analysis, piloted simulation, control law development, and flight tests. The prime contractor, Northrop Corp., was responsible for hardware design, fabrication, and integration. Interesting and unusual events in the flight testing are presented with a review of significant problems encountered in the first flight and how they were solved. Impressions by the pilots who flew the HL-10 are included. The HL-10 completed a successful 37-flight program, achieved the highest Mach number and altitude of this class vehicle, and contributed to the technology base used to develop the space shuttle and future generations of lifting bodies.

Kempel, Robert W.↗

A Supersonic Tunnel for Laser and Flow-Seeding Techniques

A supersonic wind tunnel with flow conditions of 3 lbm/s (1.5 kg/s) at a free-stream Mach number of 2.5 was designed and tested to provide an arena for future development work on laser measurement and flow-seeding techniques. The hybrid supersonic nozzle design that was used incorporated the rapid expansion method of propulsive nozzles while it maintained the uniform, disturbance-free flow required in supersonic wind tunnels. A viscous analysis was performed on the tunnel to determine the boundary layer growth characteristics along the flowpath. Appropriate corrections were then made to the contour of the nozzle. Axial pressure distributions were measured and Mach number distributions were calculated based on three independent data reduction methods. A complete uncertainty analysis was performed on the precision error of each method. Complex shock-wave patterns were generated in the flow field by wedges mounted near the roof and floor of the tunnel. The most stable shock structure was determined experimentally by the use of a focusing schlieren system and a novel, laser based dynamic shock position sensor. Three potential measurement regions for future laser and flow-seeding studies were created in the shock structure: deceleration through an oblique shock wave of 50 degrees, strong deceleration through a normal shock wave, and acceleration through a supersonic expansion fan containing 25 degrees of flow turning.

Bruckner, Robert J.↗

Long-term modulation of galactic cosmic radiation and its model for space exploration

As the human exploration of space has received new attention in the United States, studies find that exposure to space radiation could adversely impact the mission design. Galactic Cosmic Radiation (GCR), with its very wide range of charges and energies, is particularly important for a mission to Mars, because it imposes a stiff mass penalty for spacecraft shielding. Dose equivalent versus shielding thickness calculations, show a rapid initial drop on exposure with thickness, but an asymptotic behavior at a higher shielding thickness. Uncertainties in the radiobiology are largely unknown. For a fixed radiation risk, this leads to large uncertainties in shielding thickness for small uncertainties in estimated dose. In this paper we investigate the application of steady-state, spherically-symmetric diffusion-convection theory of solar modulation to individual measurements of differential energy spectra from 1954 to 1989 in order to estimate the diffusion coefficient, kappa(r,t), as a function of time. We have correlated the diffusion coefficient to the Climax neutron monitor rates and show that, if the diffusion coefficient can be separated into independent functions of space and time: kappa(r,t)=K(t) k(sub 0) beta Pk(sub 1) (r), where beta is the particle velocity and P the rigidity, then (i) The time dependent quantity 1/K(t), which is proportional to the deceleration potential, phi(r,t), is linearly related to the Climax neutron monitor counting rate. (ii) The coefficients obtained from hydrogen or helium intensity measurements are the same. (iii) There are different correlation functions for odd and even solar cycles. (iv) The correlation function for the Climax neutron monitor counting rate for given time, t, can be used to estimate mean deceleration parameter phi(t) to within +/- 15% with 90% confidence. We have shown that k(r,t) determined from hydrogen and/or helium data, can be used to fit the oxygen and iron differential energy spectra with a root mean square error of about +/- 10%, and essentially independent of the particle charge or energy. We have also examined the ion chamber and C-14 measurements which allow the analysis to be extended from the year 1906 to 1990. Using this model we have defined reference GCR spectra at solar minimum and solar maximum. These can be used for space exploration studies and provide a quantitative estimate of the error in dose due to changes in GCR intensities.

Badhwan, G. D.↗

Compton cooling of jets as the origin of radio-quiet quasars

We consider the Compton drag as a possible mechanism for jet deceleration in radio-quiet quasars, using an isotropic radiation field in a central region as a source of soft photons, provides an efficient means of decelerating electrons in a jet. Depending on the energy density of the radiation field, the jet may be stopped before reaching the radius at which the dynamical timescale is shorter than the Compton cooling timescale. We present preliminary results of our calculations and conclude that radio-quiet quasars may differ from radio-loud in their central radiation density.

Siemiginowska, Aneta↗

The collision of Jupiter and Comet Shoemaker-Levy 9

A simple description of the disruption and deceleration of 100-m- to 5-km-diameter comets striking Jupiter is combined with numerical simulations of the subsequent explosions to predict the fate of Comet Shoemaker-Levy 9. Detailed numerical simulations of the first 3 min of the explosion were performed. Our numerical simulations begin either with hot cylinders with dimensions suggested by the disruption and deceleration model or with an initial wake constructed from a moving line charge. In all cases, extensive plumes of hot gas are expelled from the atmosphere. The models with wakes evolve about twice as fast as the initially confined models. Models of both types generate similar pressure waves into the planet. Temperatures and negative hydrogen ion opacities were computed. For atmospheric entry, light curves were computed. On entry the largest bolides could be very bright, possibly as bright as Jupiter for observers placed to see them, although for kilometer-size impactors the luminosity peak is obscured by clouds. For the fireball, light curves were computed from the numerical simulations. Metals from the vaporized comet provide electrons that dramatically increase the opacity of Jovian air at low temperature. The fireball rises through and above the atmosphere, brightening at first as its surface area increases, but later fading to invisibility as its temperature drops and its opacity plummets.

Zahnle, Kevin↗

Transition to turbulence in solar surges

Transition to turbulence in magnetohydrodynamic (MHD) tearing jets has been invoked as a mechanism underlying some of the complex behavior observed in solar surges, including deceleration of the upflowing plasma and temporal correlations with types I and III radio bursts. In this paper we investigate a possible mechanism for this transition: three-dimensional secondary instabilities on two-dimensional saturated states. We find through linear analysis that these MHD configurations -- in particular, the tearing jet -- are secondarily unstable, with the dominant energy transfer from the one-dimensional field into the 3-dimensional fields. Using nonlinear simulations, we also investigate the system evolution after the secondary modes attain finite amplitude. When the tearing jet transitions to turbulence, the total kinetic energy drops rapidly corresponding to the deceleration of the jet. The electric field grows rapidly as the primary mode saturates and the three-dimensional secondary mode develops, and then decays quickly as the tearing jet becomes turbulent, providing a possible explanation for the finite duration of the associated meter-wave bursts. The electric field decays as the magnetic and velocity fields both decay. The system is dominated at late times by spanwise modes, which strongly resemble the magnetic field-aligned filamentary flows characteristic of many surges.

Dahlburg, Russell B.↗

Extended hot-gas halos around starburst galaxies

A reanalysis of Einstein Imaging Proportional Counter (IPC) data and new observations from the Ginga Large Area (Proportional) counters (LAC) indicate the presence of extended X-ray emission (10-50 kpc) around the starburst galaxy M82. Here, we discuss our model of this emission, which was obtained by performing numerical hydrodynamic simulations of the starburst event to much later times and larger scales than were previously considered. For our models, we adopted a supernova rate of 0.1/yr, and an extended low-density static halo that is bound to the galaxy. There are three stages to the evolution of the wind-blown bubble and the propagation of the shock front: the bubble expands in an almost uniform density disk gas, with a deceleration of the shock front (t is less than or approximately 3.6 Myr); breakout from the disk and the upward acceleration of the shock front (3.6 Myr is less than or approximately t is less than or approximately 18 Myr); propagation into the halo, leading to a more spherical system and shock deceleration (18 Myr is less than or approximately t). For a halo density of 10(exp -3)/cu cm, the outflow reaches a distance of 40-50 kpc from the center of the starburst galaxy in 50 Myr. We calculated the time evolution of the X-ray luminosity and found that the extended starburst emits 3 x 10(exp 39) erg/s to 10(exp 40) in the Ginga LAC band and approximately 10(exp 41) erg/s in the Einstein band. The degree of the ionization equilibrium in the outflow and its effect on the iron K alpha line emission are discussed.

Tomisaka, Kohji↗

Electron trapping in evolving coronal structures during a large gradual hard X-ray/radio burst

Gradual hard X-ray/radio bursts are characterized by their long duration, smooth time profile, time delays between peaks at different hard X-ray energies and microwaves, and radiation from extended sources in the low and middle corona. Their characteristic properties have been ascribed to the dynamic evolution of the accelerated electrons in coronal magnetic traps or to the separate acceleration of high-energy electrons in a 'second step' process. The information available so far was drawn from quality considerations of time profiles or even only from the common occurrence of emissions in different spectral ranges. This paper presents model computations of the temporal evolution of hard X-ray and microwave spectra, together with a qualitative discussion of radio lightcurves over a wide spectral range, and metric imaging observations. The basis hypothesis investigated is that the peculiar 'gradual' features can be related to the dynamical evolution of electrons injected over an extended time interval in a coronal trap, with electrons up to relativistic energies being injected simultaneously. The analyzed event (26 April. 1981) is particularly challenging to this hypothesis because of the long time delays between peaks at different X-ray energies and microwave frequencies. The observations are shown to be consistent with the hypothesis, provided that the electrons lose their energy by Coulomb collisions and possibly betatron deceleration. The access of the electrons to different coronal structures varies in the course of the event. The evolution and likely destabilization of part of the coronal plasma-magnetic field configuration is of crucial influence in determining the access to these structures and possibly the dynamical evolution of the trapped electrons through betatron deceleration in the late phase of the event.

Bruggmann, G.↗

Steady state and dynamical structure of a cosmic-ray-modified termination shock

A hydrodynamic model is developed for the structure of a cosmic-ray-modified termination shock. The model is based on the two-fluid equations of diffuse shock acceleration (Drury and Volk, 1981). Both the steady state structure of the shock and its interaction with outer heliospheric disturbances are considered. Under the assumption that the solar wind is decelerated by diffusing interstellar cosmic rates, it is shown that the natural state of the termination shock is a gradual deceleration and compression, followed by a discontinuous jump to a downstream state which is dominated by the pressure contribution of the cosmic rays. A representative model is calculated for the steady state which incorporates both interstellar cosmic ray mediation and diffusively accelerated anomalous ions through a proposed thermal leakage mechanism. The interaction of large-scale disturbances with the equilibrium termination shock model is shown to result in some unusual downstream structure, including transmitted shocks and cosmic-ray-modified contact discontinuities. The structure observed may be connected to the 2-kHz outer heliospheric radio emission (Cairns et al., 1992a, b). The time-dependent simulations also demonstrate that interaction with solar wind compressible turbulence (e.g., traveling interplanetary shocks, etc.) could induce the termination shock to continually fluctuate between cosmic-ray-dominated and gas-dynamic states. This fluctuation may represent a partial explanation of the galactic cosmic ray modulation effect and illustrates that the Pioneer and Voyager satellites will encounter an evolving shock whose structure and dynamic properties are strongly influence by the mediation of interstellar and anomalous cosmic rays.

Donohue, D. J.↗

Pick-up ion pressure gradients modulating the solar wind dynamics

Neutral interstellar atoms penetrate deeply into the inner heliosphere before they become ionized by various processes. As ions they are picked-up by the frozen-in magnetic fields and are convected outwards with the solar wind plasma. Thereby the primary plasma flow is mass, momentum, and energy-loaded. The dynamics of the distant multi-constituent solar wind is, however, not solely determined by these loading processes, but is also affected by the wave-mediated pick-up ion pressure gradients derivable from the pick-up ion distribution function. The action of the radial components of these pressures essentially counter balances the decelerating effect of the solar wind momentum loading, diminishing strongly the deceleration of the distant solar wind. Furthermore the latitudinal components of the pick-up ion pressures induce latitudinal forces acting on the multiconstituent solar plasma outflow and inducing nonradial bulk flow components. The enforced nonradial outflow geometry on the upwind hemisphere may partly be responsible for the magnetic flux deficit which was claimed since several years in the PIONEER-10 magnetic flux data.

Fahr, Hans J.↗