Search NASA⌕ Search

SEARCH · Search NASA

Results for “MAGNETRON SPUTTERING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

Cu and Ni Co-sputtered heteroatomic thin film for enhanced nonenzymatic glucose detection

Abstract In this work, we report a wafer-scale and chemical-free fabrication of nickel (Ni) and copper (Cu) heteroatomic Cu–Ni thin films using RF magnetron sputtering technique for non-enzymatic glucose sensing application. The as-prepared wafer-scale Cu–Ni thin films exhibits excellent electrocatalytic activity toward glucose oxidation with a 1.86 μM detection limit in the range of 0.01 mM to 20 mM range. The Cu–Ni film shows 1.3- and 5.4-times higher glucose oxidation activity in comparison to the Cu and Ni electrodes, respectively. The improved electrocatalytic activity is attributed to the synergistic effect of the bimetallic catalyst and high density of grain boundaries. The Cu–Ni electrodes also possessed excellent anti-interference characteristics. These results indicate that Cu–Ni heteroatomic thin film can be a potential candidate for the development of non-enzymatic glucose biosensor because of its chemical free synthesis, excellent reproducibility, reusability, and long-term stability.

59 BASIC BIOLOGICAL SCIENCES↗

Optical constants determination of samarium, holmium, and erbium in the 1.5-850 eV spectral range using a transmittance method

The optical constants {beta} and {delta} of the complex refractive index n{approx}=1-{delta}+i{beta} of Sm, Ho, and Er were obtained in the 1.5-850eV energy range using a transmittance method. Thin films of Sm, Ho, and Er were deposited by magnetron sputtering, and transmittance was measured using synchrotron radiation under a high vacuum condition. All films were directly coated on Si photodiodes, which were used as coating substrates, as well as photon detectors. Si was used as capping layer while a thin W layer was used as barrier against interface diffusion between Si and the highly reactive rare earth elements. The constants {beta} were extracted from transmittance results, and the constants {delta} were calculated based on measured {beta} values using the Kramers-Kronig formalism. Small deficiencies determined from the present data using the partial sum rules were partly attributed to the sputtered film densities that could be slightly lower than the bulk values.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Tuning magnetic properties of yttrium iron garnet film with oxygen partial pressure in sputtering and annealing process

In this paper, the magnetic properties of these films which deposited and annealed at different atmospheres were investigated. The experimental results show that the magnetic properties of yttrium iron garnet films prepared by rf magnetron sputtering method can be tuned with oxygen partial pressure in sputtering and annealing processes. The optimal condition is depositing in atmosphere of R=0 and annealing at 0.5 Pa O{sub 2}, or depositing in atmosphere of R=2% and annealed in vacuum.

36 MATERIALS SCIENCE↗

Magnetic-field-dependent morphology of self-organized Fe on stepped Si(111) surfaces

The present work reports on Fe thin films grown on vicinal Si(111) substrates via rf magnetron sputtering. The dependencies of the growth mode and magnetic properties of the obtained iron nanostructures on both crystallographic surface orientation and on the direction of the very weak stray magnetic field from the magnetron gun were studied. Scanning tunneling microscopy images showed strong dependence of the Fe grains' orientation on the stray field direction in relation to the substrate's steps demonstrating that, under appropriately directed magnetic field, Si surfaces can be used as templates for well-defined self-assembled iron nanostructures. Magneto-optical Kerr effect hysteresis loops showed an easy-axis coercivity almost one order of magnitude smaller for the film deposited with stray field applied along the steps, accompanied with a change in the magnetization reversal mode. Phenomenological models involving coherent rotation and/or domain-wall unpinning were used for the interpretation of these results.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Bandgap Engineering of Cu(In 1-x Gax)Se 2 Absorber Layers Fabricated using CuInSe 2 and CuGaSe 2 Targets for One-Step Sputtering Process

Here we have demonstrated that the bandgap of Cu(In 1-x Ga x )Se 2 (CIGS) absorber layers was readily controlled by using a one-step sputtering process. CIGS thin-film sample libraries with different Ga/(In + Ga) ratios were synthesized on soda-lime glass at 550 °C using a combinatorial magnetron sputtering system employing CuInSe 2 (CIS) and CuGaSe 2 (CGS) targets. Energy-dispersive X-ray fluorescence spectrometry (EDS-XRF) confirmed that the CIGS films had different Ga/(In + Ga) ratios, which were varied by the sample configuration on the substrate and ranged from 0.2 to 0.9. X-ray diffraction and Raman spectroscopy revealed that the CIGS films had a pure chalcopyrite phase without any secondary phase such as Cu-Se or ordered vacancy compound (OVC), respectively. Furthermore, we found that the optical bandgap energies of the CIGS films determined by transmittance measurements ranged from 1.07 eV to 1.53 eV as the Ga/(In + Ga) ratio increased from 0.2 to 0.9, demonstrating that the one-step sputtering process using CIS and CGS targets is another simple route to control the bandgap energy of the CIGS absorber layer.

14 SOLAR ENERGY↗

Bandgap widening in thermochromic Mg-doped VO{sub 2} thin films: Quantitative data based on optical absorption

Thermochromic Mg-doped VO{sub 2} films were deposited by reactive direct current magnetron sputtering onto heated glass and carbon substrates. Elemental compositions were inferred from Rutherford backscattering. Optical bandgaps were obtained from spectral transmittance and reflectance measurements—from both the film side and the back side of the samples—and ensuing determination of absorption coefficients. The bandgap of Mg-doped films was found to increase by 3.9 ± 0.5 eV per unit of atom ratio Mg/(Mg + V) for 0 < Mg/(Mg + V) < 0.21. The presence of ∼0.45 at. % Si enhanced the bandgap even more.

36 MATERIALS SCIENCE↗

Reactively-sputtered zinc semiconductor films of high conductivity for heterojunction devices

A high conductivity, n-doped semiconductor film is produced from zinc, or Zn and Cd, and group VI elements selected from Se, S and Te in a reactive magnetron sputtering system having a chamber with one or two targets, a substrate holder, means for heating the substrate holder, and an electric field for ionizing gases in the chamber. Zinc or a compound of Zn and Cd is placed in the position of one of the two targets and doping material in the position of the other of the two targets. Zn and Cd may be placed in separate targets while a dopant is placed in the third target. Another possibility is to place an alloy of Zn and dopant, or Zn, Cd and dopant in one target, thus using only one target. A flow of the inert gas is ionized and directed toward said targets, while a flow of a reactant gas consisting of hydrides of the group VI elements is directed toward a substrate on the holder. The targets are biased to attract negatively ionized inert gas. The desired stochiometry for high conductivity is achieved by controlling the temperature of the substrate, and partial pressures of the gases, and the target power and total pressure of the gases in the chamber.

Stirn, Richard J.↗

Self-organization processes in highly epitaxial La{sub 2/3}Sr{sub 1/3}MnO{sub 3} thin films grown on SrTiO{sub 3} (001) substrates

We report on the growth of highly epitaxial La{sub 2/3}Sr{sub 1/3}MnO{sub 3} thin films on SrTiO{sub 3} (001) oriented substrates by rf magnetron sputtering. It is shown that structural strain caused by lattice mismatch between film and substrate and kinetics growing instabilities may offer unique opportunities to control the film morphologies. By increasing growth rate, the surface morphology undergoes a dramatic transformation: from very smooth surface through arrays of mounds or antidots to hatched morphology. All nano-objects form long-range ordered arrays running in the steps direction defined by the miscut angle of underlying substrate. These self-assembled structures are of high interest envisaging a new route for the fabrication of oxide-based magnetoelectronic devices by using a bottom-up approach.

36 MATERIALS SCIENCE↗

Synthesis,Structure and Electrical Properties of(SnO{sub 2}){sub x}(In{sub 2}O{sub 3}){sub 1-x}(x=0.5-1) Nanocomposites

The experimental results of synthesizing thin films (<1 {mu}m thick) of (SnO{sub 2}){sub x}(In{sub 2}O{sub 3}){sub 1-x} (x = 0.5-1 wt) nanocomposites fabricated by high-frequency magnetron sputtering of metal-oxide targets in a controlled Ar + O{sub 2} atmosphere are presented. The films, deposited on hot substrates (400 Degree-Sign C), are studied by the X-ray diffraction analysis, atomic-force microscopy, and optical and electrical methods. The effect of the synthesis conditions and film composition on the size of crystalline grains, band gap, and the concentration and mobility of free charge carriers was determined. It is shown that films of the composition (SnO{sub 2}){sub x}(In{sub 2}O{sub 3}){sub 1-x} with x = 0.9 are the most promising for applications in gas sensorics.

36 MATERIALS SCIENCE↗

Giant magnetoresistance and superparamagnetism in Dy{sub x}Fe{sub 100-x} nanogranular magnetic thin films at room temperature

In this article, Dy{sub x}Fe{sub 100-x} nanogranular (15 ≤ x ≤ 25) thin films have been prepared at ambient temperature by dc magnetron sputtering. The correlation between the microstructure, magneto transport and magnetization properties is discussed. The grain size of Dy (Dysprosium) and Fe (Iron) was measured to be about 2 to 3 nm, respectively and the distribution of grains was homogenous throughout the sample. The magnetoresistance is sensitive to microstructural changes (particle size as well as Dy concentration). At the room temperature, the magnetoresistance [MR %] increased from 0.2 to 2.2 with increase in atomic concentration of Dy from x = 15 to 25 and we obtained maximum 2.2 MR [%] for x = 25 in this series of samples. The magnetization studies have revealed that all the samples are superparamagnetic (SPM) at room temperature.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Tilt of the columnar microstructure in off-normally deposited thin films using highly ionized vapor fluxes

The tilt of the columnar microstructure has been studied for Cu and Cr thin films grown off-normally using highly ionized vapor fluxes, generated by the deposition technique high power impulse magnetron sputtering. It is found that the relatively large column tilt (with respect to the substrate normal) observed for Cu films decreases as the ionization degree of the deposition flux increases. On the contrary, Cr columns are found to grow relatively close to the substrate normal and the column tilt is independent from the ionization degree of the vapor flux when films are deposited at room temperature. The Cr column tilt is only found to be influenced by the ionized fluxes when films are grown at elevated temperatures, suggesting that film morphology during the film nucleation stage is also important in affecting column tilt. A phenomenological model that accounts for the effect of atomic shadowing at different nucleation conditions is suggested to explain the results.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Tungsten oxide proton conducting films for low-voltage transparent oxide-based thin-film transistors

Tungsten oxide (WO{sub x}) electrolyte films deposited by reactive magnetron sputtering showed a high room temperature proton conductivity of 1.38 Multiplication-Sign 10{sup -4} S/cm with a relative humidity of 60%. Low-voltage transparent W-doped indium-zinc-oxide thin-film transistors gated by WO{sub x}-based electrolytes were self-assembled on glass substrates by one mask diffraction method. Enhancement mode operation with a large current on/off ratio of 4.7 Multiplication-Sign 10{sup 6}, a low subthreshold swing of 108 mV/decade, and a high field-effect mobility 42.6 cm{sup 2}/V s was realized. Our results demonstrated that WO{sub x}-based proton conducting films were promising gate dielectric candidates for portable low-voltage oxide-based devices.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Study of plasma dynamics in a modulated pulsed power magnetron discharge using a time-resolved Langmuir probe

Modulated pulse power (MPP) technology is a derivative of high power pulsed magnetron sputtering that allows unprecedented user control over the growth process, although the critical time-dependent plasma properties during the power pulse have not been studied until now. Using a MPP plasma generator, pulses of custom voltage waveforms were generated and applied to the cathode of a 36 cm diameter circular planar magnetron. The I-V characteristics of the pulses are separable into distinct discharge stages. A time-resolved triple Langmuir probe was introduced to measure the temporal evolution of the plasma. Typical electron density of 5x10{sup 17} m{sup -3} and electron temperature of 10 eV during the pulse were calculated from measured parameters. Plasma behaviors were observed to closely depend on the pulse waveforms. Various parameters, including pulse current, pulse frequency, pressure, and distance from the target, also affected the electron density and temperature, providing degrees of freedom to optimize the sputtering processes. The effects of each parameter on the pulsed plasma dynamics are discussed and then attributed to mechanisms of electron impact ionization, gas heating, and magnetic confinement.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Phase investigation in Pt supported off-stoichiometric iron-platinum thin films

Graphical abstract: - Highlights: • Low temperature FePt L1{sub 0} phase transformation using Pt/Fe{sub 3}Pt/Pt structure. • Temperature dependent FCC to FCT phase investigation using Rietveld refinement. • Estimation of soft and hard ferromagnetic contribution from demagnetization curve. • Interlayer diffusion and stoichiometry conformation of L1{sub 0} phase using RBS. • Correlation of structural, magnetic and RBS studies were successfully understood. - Abstract: The structural and magnetic phase transformation of Pt/Fe{sub 3}Pt/Pt films on Si <1 0 0> substrates prepared by DC magnetron sputtering is investigated as a function of annealing temperature. Pt diffusion driven low temperature phase transformation from A1 to L1{sub 0} phase is achieved at 300 °C, attaining a very high coercivity of 9 kOe. At 300 °C, 85% L1{sub 0} phase transformation is observed using the X-ray diffraction profile fitting. The estimated phase content is also further verified by fitting the demagnetization curve. The underlayer promotes the ordering at lower temperature while overlayer induces growth along (0 0 1) preferred orientation. Rutherford back scattering study reveals interlayer diffusion and confirms the desired stoichiometry for L1{sub 0} phase. The presence of Pt under-overlayer provides the Pt source and further facilitates the Pt diffusion, which makes it effective in promoting the phase ordering at a lower temperature.

36 MATERIALS SCIENCE↗

Embedded argon as a tool for sampling local structure in thin plasma deposited aluminum oxide films

Al{sub 2}O{sub 3} thin films, either amorphous or of varying degrees of crystallinity, were deposited by two-frequency radio-frequency magnetron sputtering. Film crystallinity was investigated by Fourier transform infrared spectroscopy and X-ray diffraction (XRD). X-ray photoelectron spectroscopy (XPS) was employed to determine the amount of Ar naturally trapped within the films during the deposition process. A clear correlation was found between the existence of crystalline phases, as determined by XRD, and a shift towards lower binding energy positions of the Ar2p core levels of embedded gas. The shift is due to differences in the local Al{sub 2}O{sub 3} matrix (amorphous or crystalline) of the embedded gas, thus, providing an XPS fingerprint that can be used to qualitatively determine the presence or absence of crystalline phases in very thin films.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Electrical Properties of p-NiO/n-Si Heterostructures Based on Nanostructured Silicon

Silicon nanowires are formed on n-Si substrates by chemical etching. p-NiO/n-Si heterostructures are fabricated by reactive magnetron sputtering. The energy diagram of anisotype p-NiO/n-Si heterostructures is constructed according to the Anderson model. The current–voltage and capacitance–voltage characteristics are measured and analyzed. The main current-transport mechanisms through the p-NiO/n-Si heterojunction under forward and reverse biases are established.

36 MATERIALS SCIENCE↗

Dual anisotropic character in Fe/Pt multilayer grown on (001) MgO substrate

The multilayers of [Fe(5Å)/Pt(25 Å)]{sub ×15} were prepared by dc magnetron sputtering on 50 Å Pt-buffered MgO substrates. The structural characterization of the multilayers was carried out using X-ray diffraction, X-ray reflectivity. The Secondary ion mass spectroscopy measurement reveals the depth profile and compositional modulations of the multilayer films as per our design specifications. Room temperature magnetic measurements were carried out by using SQUID both in-plane and out-of-plane sample geometry. Magnetization measurements show similar M-H loops for both in-plane and out-of-plane directions of external magnetic field with a coercivity of 190 Oe. These measurements indicate that our samples are magnetically soft and have multifunctional character which is important for making magnetic tunnel junctions.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Room temperature ferromagnetic and ferroelectric properties of Bi{sub 1−x}Ca{sub x}MnO{sub 3} thin films

Bi{sub 1−x}Ca{sub x}MnO{sub 3} (BCMO) thin films with x = 0, 0.1, 0.2, 0.3 and 0.4 are successfully deposited on the n-type Si (100) substrate at two different temperatures of 400 °C and 800 °C using RF magnetron sputtering. The stoichiometry of the films and oxidation state of the elements have been described by X-ray photoelectron spectroscopy analysis. Dielectric measurement depicts the insulating property of BCMO films. Magnetic and ferroelectric studies confirm the significant enhancement in spin orientation as well as electric polarization at room temperature due to incorporation of Ca{sup 2+} ions into BiMnO{sub 3} films. The BCMO (x = 0.2) film grown at 400 °C shows better magnetization (M{sub sat}) and polarization (P{sub s})with the measured values of 869 emu / cc and 6.6 μ{sub C}/ cm{sup 2} respectively than the values of the other prepared films. Thus the realization of room temperature ferromagnetic and ferroelectric ordering in Ca{sup 2+} ions substituted BMO films makes potentially interesting for spintronic device applications.

36 MATERIALS SCIENCE↗