Search NASA⌕ Search

SEARCH · Search NASA

Results for “Microstructural properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

Influence of sintering conditions on the microstructure and optical properties of Eu: CaF{sub 2} transparent ceramic

Highlights: • Eu: CaF2 ceramics sintering at different conditions were fabricated by HP method. • The results show that the temperatures have great effect on the microstructure. • The ceramic sintered at 600 °C/30 MPa has high transmittance and pore-free structure. • The diffusion and densification process mainly occurs between 350 °C and 500 °C. • The optical losses in ceramic were caused by structure defects and polishing damage. - Abstract: Nanopowders of the 5 at.% Eu doped CaF{sub 2} have been synthesized by co-precipitated method. X-ray diffraction (XRD) indicated that the samples corresponds to the cubic CaF{sub 2} phase and scanning electron microscopy (SEM) showed that the morphology of nanopowders were approximately spherical. The Eu: CaF{sub 2} transparent ceramics were fabricated by hot-pressing (HP) method at different P-T conditions in a vacuum environment. The fracture surface, the relative density, average grain size and shrinkage displacements were also studied to analysis the influence of sintering conditions on Eu: CaF{sub 2} ceramic. In comparison with other samples, the proper sintering temperature and pressure was 600 °C/30 MPa. The transmittance of ceramic was up to 79.7% and 88.85% at the wavelength of 760 nm and 2400 nm. Furthermore, the emission spectra of Eu: CaF{sub 2} transparent ceramics under 393.5 nm excitation was also discussed.

36 MATERIALS SCIENCE↗

Microstructure and Mechanical Properties of Dissimilar Joints of Al-Mg{sub 2}Si and 5052 Aluminum Alloy by Friction Stir Welding

Al-Mg{sub 2}Si alloy and 5052 Al alloy were welded successfully by friction stir welding (FSW) in this study. The results show that the alloy consists of three distinct zones after FSW: the base material zone (BMZ), the transitional zone, and the weld nugget (WN). The morphologies of the primary Mg{sub 2}Si phases are identified as coarse equiaxed crystals for Al-Mg{sub 2}Si alloys in the BMZ. The WN is a mixture of rich Al-Mg{sub 2}Si and rich 5052 alloy, and a banded structure is formed in the zone. Interestingly, in the WN, the equiaxed crystals changed to polygonal particles with substantially reduced sizes in the rich Al-Mg{sub 2}Si zone. However, in addition to the white rich Mg phase appearing in the rich 5052 zone near the interface, the 5052 alloy does not show obvious changes. The hardness gradually increases from the BMZ of the 5052 to the welded joint to the Al-Mg{sub 2}Si BMZ. In addition, the ultimate tensile strength (UTS) of the welded joint is higher than that of the base material of the Al-Mg{sub 2}Si, whereas it is lower than that of the 5052 base alloy. The results of the elongation are similar to the UTS results. The fracture mechanism is also investigated.

36 MATERIALS SCIENCE↗

Current-Assisted Diffusion Bonding of Extruded Ti-22Al-25Nb Alloy by Spark Plasma Sintering: Interfacial Microstructure and Mechanical Properties

Spark plasma sintering (SPS) technology was used to current-assisted bond extruded Ti-22Al-25Nb alloy. The effects of bonding temperature (920-980 °C) and bonding time (10-30 min) on the microstructure evolution and shear strength of this alloy were investigated systematically. The temperature distribution in the specimen during the current-assisted bonding process was also analyzed by numerical simulation. It is noted that the highest temperature was obtained at the bonding interface. As the bonding temperature and bonding time increased, the voids in the interface shrank increasingly until they vanished. A complete metallurgical bonding interface could be produced at 960 °C/20 min/10 MPa, exhibiting the highest shear strength of 269.3 MPa. In addition, the shear strength of the bonded specimen depended on its interfacial microstructure. With increased bonding temperature, the fracture mode transformed from the intergranular fracture at the bonding interface to the cleavage fracture in the substrate.

36 MATERIALS SCIENCE↗

Impact of Irradiation on Microstructure and Mechanical Properties of Materials Produced by Advanced Manufacturing

Advanced non-light water reactor designs, known as Generation IV (Gen IV) reactors, typically operate at higher temperatures and under more extreme radiation conditions than conventional light water reactors. A critical aspect of the successful deployment and advancement of Gen IV reactor designs is the selection of appropriate structural materials for specific applications, which necessitates the timely development of new materials and manufacturing processes. Advanced manufacturing (AM) offers numerous opportunities for innovative designs, enabling the production of high-performance components with potentially shorter development cycles compared to traditional manufacturing methods. However, a significant challenge in deploying AM technologies in the nuclear energy sector is the current lack of data on the irradiation performance of AM-produced components. This presentation will discuss neutron and ion irradiation results of AM materials, including stainless steel 316L, Grade 91, SA508, Inconel 718, and Inconel 625 materials. The materials were manufactured by AM, such as Powder Metallurgy Hot Isostatic Pressing (PM HIP), Laser Powder Bed Fusion (LPBF) and Directed Energy Deposition (DED). The effects of neutron irradiation on microstructure (e.g., dislocations, loops, and nanoclusters), tensile properties (e.g., strength and ductility), and ion irradiation on Irradiation-Assisted Stress Corrosion Cracking (IASCC) will be explored. Results are collected from several projects supported by the Nuclear Science User Facilities (NSUF) program.

36 - MATERIALS SCIENCE↗

Influence of rare earth ions on microstructural and optical properties of ZnO nanostructures

Pure and 3% rare earth ions (Nd{sup 3+} & Gd{sup 3+}) doped ZnO samples were synthesized by sol-gel method, followed by annealing at temperature 450°C for 2hr. The samples were characterized by XRD, FTIR and UV-visible spectroscopy. XRD result confirmed single phase nature of all samples with crystalline structure. The average crystallite size of the doped samples found to be decreases as caculated using Debye-Scherrer’s formula. FTIR spectra indicate absorption band centered at 464 cm{sup −1} which is attributed to Zn-O lattice vibration. It confirms the formaton of compounds. UV-visible spectroscopy was used to study the optical properties and band gap of the synthesised materials using Tauc’s relation.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Effects of low-temperature neutron irradiation on the microstructure and tensile properties of duplex 2304 stainless steel and its electron-beam welds

A lean duplex stainless steel material (2304-grade) in its base metal and electron beam (e-beam) welded conditions were studied microstructurally and mechanically as a function of irradiation conditions to evaluate its use as a structural material at low temperatures (60–100 °C). Neutron irradiation up to a fluence of 1.40 × 10 19 n/cm 2 (E > 0.1 MeV) or ~0.011 dpa decreased the total elongation of both base metal and e-beam welded samples. Overall, radiation hardening was observed in all the samples. The transversely cut irradiated samples showed some nonuniform quasi-cleavage and shearing in their fracture surfaces, indicating the variance of ductile nature of the two-phased (deformable austenite and harder ferrite) duplex structure. The e-beam welded samples also showed quasi-cleavage fracture, which is a characteristic of radiation-induced embrittlement. Furthermore, these observations of the e-beam welded samples were attributed to the formation of coarse ferrites, grain boundary and intragranular phases such as γ 2 and γ 3 , and minor impurity phases such as CrN and Cr 2 N in the weld pool and/or heat-affected zone of the samples. Radiation-induced elemental segregation was also identified in the post-irradiated base metal.

36 MATERIALS SCIENCE↗

Microstructural, dielectric and magnetic properties of multiferroic composite system barium strontium titanate – nickel cobalt ferrite

Multiferroic composites (1-x) Ba{sub 0.95}Sr{sub 0.05}TiO{sub 3} + (x) Ni{sub 0.8}Co{sub 0.2}Fe{sub 2}O{sub 4} (where x = 0.1, 0.2, 0.3, 0.4) has been prepared by solid state reaction method. X-ray diffraction analysis of the composite samples confirmed the presence of both barium strontium titanate (BST) and nickel cobalt ferrite (NCF) phases. FESEM images indicated the well dispersion of NCF grains among BST grains. Dielectric constant and loss of the composite samples decreases with increase in frequency following Maxwell-Wagner relaxation mechanism. Composite sample with highest ferrite content possesses highest values of remanent and saturation magnetization.

36 MATERIALS SCIENCE↗

Nanostructured cobalt powders synthesised by polyol process and consolidated by Spark Plasma Sintering: Microstructure and mechanical properties

Bulk nanostructured cobalt was processed using a bottom-up strategy. Nanostructured particle agglomerates of about 50 and 240 nm in diameter were synthesised using a polyol route and subsequently consolidated by Spark Plasma Sintering (SPS). The microstructure of the starting powders and of the processed bulk samples was studied and characterised by X-ray diffraction (XRD) and transmission electron microscopy (TEM). The XRD patterns of the as-prepared powders showed predominantly a face centred cubic (fcc) crystalline phase, whereas both fcc and hexagonal close packed (hcp) phases were found within the consolidated samples. A sample with the highest relative mass density (94.5%) was obtained from the small powder particles. TEM observations revealed a lamellar substructure with a high density of nanotwins and stacking faults in every grain in the sample with the highest density. Brillouin light scattering (BLS) and quasistatic compression tests were used to investigate the mechanical properties of the consolidated samples. The two techniques yielded Young modulus values of 168 GPa and 130 GPa, respectively, in the sample with the highest density. This sample also exhibited a yield stress higher than 1 GPa after the compression test, which is mainly attributed to the lamellar-like structure occurring in almost every grain of the polycrystalline aggregate. - Highlights: Black-Right-Pointing-Pointer Cobalt nanoparticles produced by the polyol process present mainly the fcc metastable phase. Black-Right-Pointing-Pointer Bulk nanostructured cobalt is obtained from the nano-particles by Spark Plasma Sintering consolidation. Black-Right-Pointing-Pointer Nanotwins and stacking faults are present in every grain of the more dense sample. Black-Right-Pointing-Pointer Yield strength and plastic domain may be varied depending on the nanoparticle size and the porosity of the consolidated material.

36 MATERIALS SCIENCE↗

Microstructure and Mechanical Properties of Stainless Steel/Brass Joints Brazed by Sn-Electroplated Ag Brazing Filler Metals

To develop a high-Sn-content AgCuZnSn brazing filler metal, the BAg50CuZn was used as the base filler metal and a Sn layer was electroplated upon it. Then, the 304 stainless steel and the H62 brass were induction-brazed with the Sn-plated brazing filler metals. The microstructures of the joints were examined with an optical microscope, a scanning electron microscope and an x-ray diffractometer. The corresponding mechanical properties were obtained with a universal tensile testing machine. The results indicated that the induction brazed joints consisted of the Ag phase, the Cu phase and the CuZn phase. When the content of Sn in the Sn-plated Ag brazing filler metal was 6.0 or 7.2 wt.%, the Cu{sub 5}Zn{sub 8}, the Cu{sub 41}Sn{sub 11} and the Ag{sub 3}Sn phases appeared in the brazed joint. The tensile strength of the joints brazed with the Sn-plated filler metal was higher compared to the joints with the base filler metal. When the content of Sn was 6.0 wt.%, the highest tensile strength of the joint reached to 395 MPa. The joint fractures presented a brittle mode, mixed with a low amount of ductile fracture, when the content of Sn exceeded 6.0 wt.%.

36 MATERIALS SCIENCE↗

Experimental Study of the Microstructure and Micromechanical Properties of Laser Cladded Ni-based Amorphous Composite Coatings

(Ni{sub 0.6}Fe{sub 0.4}){sub 65}B{sub 18}Si{sub 10}Nb{sub 4}C{sub 3} amorphous composite coating was successfully fabricated on AISI 1045 steel substrate by using laser cladding process with coaxial powder feeding equipment. The microstructure and phase distribution of the coating were investigated by using x-ray diffraction, scanning electron microscopy and transmission electron microscope. The mechanical properties of the coating were examined by using microhardness testing and nanoindentation. The experimental results indicated that the volume fraction of amorphous phase increased with the decrease in laser cladding heat input, leading to an improvement of mean microhardness and nanohardness. NbC particles in a size ranging between 150 and 1650 nm were found embedding in the amorphous composite coatings in all situations. The presence of the NbC particles can contribute to an improvement of 96.7 HV in hardness on the basis of experimental results, while theoretical prediction suggests an improvement of 92.5 HV by using Orowan-Ashby equation.

36 MATERIALS SCIENCE↗

The partial substitution of Y with Gd on microstructures and mechanical properties of as-cast and as-extruded Mg-10Zn-6Y-0.5Zr alloy

Highlights: • The as-extruded Mg-10Zn-6Y-0.5Zr and Mg-10Zn-3Y-3Gd-0.5Zr alloys show bimodal microstructure and DRXed microstructure. • In addition to W phase, Icosahedral quasicrystal phase layer is observed at the surface of some W phase particles in as-extruded Mg-10Zn-3Y-3Gd-0.5Zr (wt. %) alloy. • The as-extruded Mg-10Zn-6Y-0.5Zr (wt. %) alloy exhibits TYS of 341 MPa, UTS of 368 MPa and elongation to failure of 6.8%. While the as-extruded Mg-10Zn-3Y-3Gd-0.5Zr (wt. %) alloy shows lower TYS of 247 MPa, UTS of 330 MPa and higher elongation to failure of 19.8%. - Abstract: Mg-10Zn-6Y-0.5Zr (wt%) alloy and Mg-10Zn-3Y-3Gd-0.5Zr (wt%) alloy with medium RE content have been fabricated by conventional casting and indirect extrusion. The as-extruded Mg-10Zn-6Y-0.5Zr (wt%) alloy shows a bimodal microstructure containing dynamic recrystallized (DRXed) grains with average grain size of 2 μm and deformed regions. In addition to the fragmented W phase particle bands distributing along the extrusion direction, large amount of nano W phase and small amount of nano β{sub 2}′ phase are precipitated in the matrix. While the as-extruded Mg-10Zn-3Y-3Gd-0.5Zr (wt%) alloy exhibits completely dynamic recrystallized microstructure with average grain size of 3 μm. The broken W phase particles are distributed homogeneously in the matrix. Icosahedral quasicrystal phase layer is observed at the surface of some W phase particles in the as-extruded Mg-10Zn-3Y-3Gd-0.5Zr alloy. The as-extruded Mg-10Zn-6Y-0.5Zr (wt%) alloy exhibits yield strength of 341 MPa, ultimate tensile strength of 368 MPa and elongation to failure of 6.8%. While the as-extruded Mg-10Zn-3Y-3Gd-0.5Zr (wt%) alloy shows lower yield strength of 247 MPa, ultimate tensile strength of 330 MPa and higher elongation to failure of 19.8%. The higher strength in the as-extruded Mg-10Zn-6Y-0.5Zr (wt%) alloy is mainly attributed to higher area fraction of unDRXed regions with strong texture and the precipitation of nano W and β{sub 2}′ phase. The fully recrystallized microstructure with weak texture and the formation of icosahedral quasicrystal phases with good coherent bond with α-Mg contribute to the good ductility of the as-extruded Mg-10Zn-3Y-3Gd-0.5Zr alloy.

36 MATERIALS SCIENCE↗

Effect of Yttrium Addition on the Microstructure and Mechanical Properties of Cu-Rich Nano-phase Strengthened Ferritic Steel

Due to the brittle problem of Cu-rich nano-phase strengthened ferritic steel (CNSFS) after air aging, the effect of Y addition in CNSFS was systemically investigated in the present work. The microstructure, tensile fracture morphology and oxide layer of the steels were surveyed by optical microscope and scanning electron microscope. Transmission electron microscope with the combination of energy-dispersive x-ray spectroscopy and selected area electron diffraction was used to analyze the morphology, size, number density, chemical compositions and crystal structure for nano-crystalline precipitates. Microstructural examinations of the nano-crystalline precipitates show that Cu-rich precipitates and Y compounds in the range of 2-10 and 50-100 nm, respectively, form in the Y-containing steel; meanwhile, the average size of nano-crystalline precipitates in Y-containing steel is larger, but the number density is lower, and the ferritic grains are refined. Furthermore, the tensile strength and ductility of Y-containing steel after air aging are improved, whereas the tensile strength is enhanced and the ductility decreased after vacuum aging. The drag effect of Y makes the oxide layer thinner and be compacted. Tensile properties of CNSFS after air aging are improved due to the refined grains, antioxidation and purification by the addition of Y.

36 MATERIALS SCIENCE↗

Effect of deposition pressure on the microstructure and thermoelectric properties of epitaxial ScN(001) thin films sputtered onto MgO(001) substrates

Four epitaxial ScN(001) thin films were successfully deposited on MgO(001) substrates by dc reactive magnetron sputtering at 2, 5, 10, and 20 mTorr in an Ar/N2 ambient atmosphere at 650 °C. The microstructure of the resultant films was analyzed by x-ray diffraction, scanning electron microscopy, and transmission electron microscopy. Electrical resistivity, electron mobility and concentration were measured using the room temperature Hall technique, and temperature dependent in-plain measurements of the thermoelectric properties of the ScN thin films were performed. The surface morphology and film crystallinity significantly degrade with increasing deposition pressure. The ScN thin film deposited at 20 mTorr exhibits the presence of <221> oriented secondary grains resulting in decreased electric properties and a low thermoelectric power factor of 0.5 W/m-K² at 800 K. ScN thin films grown at 5 and 10 mTorr are single crystalline, yielding the power factor of approximately 2.5 W/m-K² at 800 K. The deposition performed at 2 mTorr produces the highest quality ScN thin film with the electron mobility of 98 cm² V⁻¹ s⁻¹ and the power factor of 3.3 W/m-K² at 800 K.

36 MATERIALS SCIENCE↗

The Effect of Arc Current on Microstructure and Mechanical Properties of Hybrid LasTIG Welds of High-Strength Low-Alloy Steels

A hybrid laser-tungsten inert gas (LasTIG) welding system was applied for 3-mm-thick S460MC and S700MC high-strength low-alloy steel sheet butt welding with the aim to reduce the cooling rate compared with laser welding. The effect of the electric current was evaluated. Increasing arc current led to the increase of fused metal and heat-affected-zone (HAZ) dimensions. Fused metal grains were larger whereas the microhardness increase toward the base metal was lower at higher currents in this region. Microhardness peaks corresponding to the coarse-grained HAZ were reduced at higher currents for S460MC but were almost not affected in S700MC. The tensile strength of both the laser weld and LasTIG welds was comparable to the base metal for both alloys.

36 MATERIALS SCIENCE↗

Interfacial Microstructure and Mechanical Properties of Friction Stir Welded Joints of Commercially Pure Aluminum and 304 Stainless Steel

In the present investigation, friction stir welding of commercially pure aluminum and 304 stainless steel was carried out at varying tool rotational speeds from 200 to 1000 rpm in steps of 200 rpm using 60 mm/min traverse speed at 2 (degree) tool tilt angle. Microstructural characterization of the interfacial zone was carried out using optical microscope and scanning electron microscope. Energy-dispersive spectroscopy indicated the presence of FeAl{sub 3} intermetallic phase. Thickness of the intermetallic layer increased with the increase in tool rotational speed. X-ray diffraction studies indicated the formation of intermetallic phases like FeAl{sub 2}, Fe{sub 4}Al{sub 13}, Fe{sub 2}Al{sub 5}, and FeAl{sub 3}. A maximum tensile strength of ~ 90% that of aluminum along with ~ 4.5% elongation was achieved with the welded sample at tool rotational speed of 400 rpm. The stir zone showed higher hardness as compared to base metals, heat affected zone, and thermo-mechanically affected zone due to the presence of intermetallics. The maximum hardness value at the stir zone was achieved at 1000 rpm tool rotational speed.

36 MATERIALS SCIENCE↗

Chemical composition, microstructure, and hygroscopic properties of aerosol particles at the Zotino Tall Tower Observatory (ZOTTO), Siberia, during a summer campaign

In this study we describe the hygroscopic properties of accumulation- and coarse-mode aerosol particles sampled at the Zotino Tall Tower Observatory (ZOTTO) in Central Siberia (61° N; 89° E) from 16 to 21 June 2013. The hygroscopic growth measurements were supplemented with chemical analyses of the samples, including inorganic ions and organic/elemental carbon. In addition, the microstructure and chemical composition of aerosol particles were analyzed by X-ray micro-spectroscopy (STXM-NEXAFS) and transmission electron microscopy (TEM). A mass closure analysis indicates that organic carbon accounted for 61 and 38% of PM in the accumulation mode and coarse mode, respectively. The water soluble fraction of organic matter was estimated to be 52 and 8% of PM in these modes. Sulfate, predominantly in the form of ammoniated sulfate, was the dominant inorganic component in both size modes: ~ 34% in the accumulation vs. ~ 47% in the coarse mode. The hygroscopic growth measurements were conducted with a filter-based differential hygroscopicity analyzer (FDHA) over the range of 5–99.4% RH in the hydration and dehydration operation modes. The FDHA study indicates that both accumulation and coarse modes exhibit pronounced water uptake approximately at the same RH, starting at ~ 70%, while efflorescence occurred at different humidities, i.e., at ~ 35% RH for submicron particles vs. ~ 50% RH for supermicron particles. This ~ 15% RH difference was attributed to higher content of organic material in the submicron particles, which suppresses water release in the dehydration experiments. The kappa mass interaction model (KIM) was applied to characterize and parameterize non-ideal solution behavior and concentration-dependent water uptake by atmospheric aerosol samples in the 5–99.4% RH range. Based on KIM, the volume-based hygroscopicity parameter, &kappa; v , was calculated. The &kappa; v, ws value related to the water soluble (ws) fraction was estimated to be ~ 0.15 for the accumulation mode and ~ 0.36 for the coarse mode, respectively. The obtained &kappa; v, ws for the accumulation mode is in good agreement with earlier data reported for remote sites in the Amazon rain forest (&kappa; v &approx; 0.15) and a Colorado boreal forest (&kappa; v &approx; 0.16). We used the Zdanovskii–Stokes–Robinson (ZSR) mixing rule to predict the chemical composition dependent hygroscopicity, &kappa; v, p . The obtained &kappa; v, p values overestimate the experimental FDHA-KIM-derived &kappa; v, ws by factors of 1.8 and 1.5 for the accumulation and coarse modes, respectively. This divergence can be partly explained by incomplete dissolution of the hygroscopic inorganic compounds resulting from kinetic limitations due to a sparingly soluble organic coating. The TEM and STXM-NEXAFS results indicate that aged submicron (>300 nm) and supermicron aerosol particles possess core-shell structures with an inorganic core, and are enriched in organic carbon at the mixed particle surface. The direct FDHA kinetic studies provide a bulk diffusion coefficient of water of ~ 10 &minus;12 cm 2 s &minus;1 indicating a semi-solid state of the organic-rich phase leading to kinetic limitations of water uptake and release during hydration and dehydration cycles. Overall the present ZOTTO data set, obtained in the growing season, has revealed a strong influence of organic carbon on the hygroscopic properties of the ambient aerosols. The sparingly soluble organic coating controls hygroscopic growth, phase transitions, and microstructural rearrangement processes. The observed kinetic limitations can strongly influence the outcome of experiments performed on multi-second time scales, such as the commonly applied HTDMA (Hygroscopicity Tandem Differential Mobility Analyzer) and CCNC (Cloud Condensation Nuclei Counter) measurements.

54 ENVIRONMENTAL SCIENCES↗

Influence of Packing Atmosphere on the Microstructures and Transport Properties of Bi-2223/AgAu Tapes

Oxygen partial pressure was the key factor to tune the phase evolution mechanism of Bi-2223 system. In order to investigate the influence of packing atmosphere on the phase formation rate of Bi-2223, microstructures‚ and the current capacity of final tapes‚ 37-filamentary Bi-2223/AgAu tapes were fabricated by powder-in-tube (PIT) process, and the powder packing process operated in the glove box under different atmosphere of pure O{sub 2}‚ air, and N{sub 2}–7.5%O{sub 2}, with the oxygen partial pressure of 100%‚ 25%, and 7.5%, respectively. With different packing atmosphere, the phase formation rate of Bi-2223 increased obviously during the first heat treatment process (HT1). While, based on the same HT1 process, the maximum Bi-2223 phase content was obtained in the tapes with packing atmosphere of N{sub 2}–7.5%O{sub 2}‚ which should be attributed to the suitable Bi-2223 content and distribution. Due to the improvement of superconducting phase content and better texture structure, the critical current density increased with decreasing oxygen partial pressure of packing atmosphere and the maximum value of 19.9 kA/cm{sup 2} was reached. Moreover‚ the in-field current capacities of these Bi-2223/AgAu tapes have also been enhanced with low oxygen partial pressure in packing atmosphere, attributed to the improvements of intergrain connectivity.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Relationship between microstructure and mechanical properties of M50 ultra-high strength steel via quenching-partitioning-tempering process

Highlights: • The impact energy of M50 steels treated by QPT process increases by 35–93% than QT. • Cracks distribution inside impact fracture specimens is studied by 3D X-ray tomography. • The work indicates that QPT process can be applied to high-C steel with little Si. Novel quenching-partitioning-tempering (Q-P-T) and traditional quenching-tempering (Q-T) processes are conducted for M50 ultra-high strength steel. An excellent combination of strength and toughness is obtained via the Q-P-T process. The highest impact absorption energy of the Q-P-T specimen increases by 93% compared to the Q-T specimen. However, the yield and ultimate tensile strength of Q-P-T specimens are almost the same as those of Q-T specimens. Microstructure analysis indicates that the maximum fraction of retained austenite in the Q-P-T specimen is 7.5%, which is much higher than that in the Q-T (2.0%) specimen. Meanwhile, more fine cracks appear in the fracture Q-P-T specimen. The precipitation of fine and diffuse ω phase, Fe{sub 3}C and Cr{sub 23}C{sub 6} is observed during the partitioning process. The present work also reveals that the Q-P-T/Q-P process can be applied to high‑carbon steel with little Si or Al.

36 MATERIALS SCIENCE↗