Search NASA⌕ Search

SEARCH · Search NASA

Results for “Relative Permeability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

Bioethanol enrichment using zeolite membranes: Molecular modeling, conceptual process design and techno-economic analysis

Lignocellulosic biomass-derived ethanol offers a potential alternative to fossil-derived fuels. However, the energy-intensive nature of its recovery process, i.e., a sequence of two distillation columns – beer and rectification columns - enriching from 5 to 37, and 37–93 wt%, respectively, limits its environmental and economic benefits. Here, in this paper, we assess the potential of using zeolite membranes for bioethanol recovery. Atomistic-level and molecular dynamic simulations are performed to determine adsorption and diffusion properties of the ethanol-water mixture in zeolite membranes. These properties are modeled using the real adsorption solution theory and the Maxwell-Stefan equations to describe permeation through the zeolite membranes. A comparison of steady state permeance and selectivity predicted by the model with the values from experiments suggests that the simulated membranes are more permeable and selective than the real membranes. This is attributed to the presence of structural non-idealities and hydrophilic defects in real membranes, while the adsorption and diffusion properties obtained using molecular simulations reflect the behavior in ideal crystals. Thus, a reduced diffusivity model with an empirical relation for enhanced water adsorption is used to capture similar performance as that obtained by real membranes. This model is further used in developing conceptual process designs to assess the viability of zeolite membranes for bioethanol enrichment in industry. Both hydrophobic and hydrophilic zeolite membranes are considered. Hydrophobic zeolite membranes show potential for energy savings but lack in separation performance. On the other hand, hydrophilic zeolite membranes can achieve the separation target but result in no energy savings. Thus, a configuration that uses a combination of hydrophobic and hydrophilic membranes is proposed. It can achieve the separation target and results in 15% energy savings over distillation. Techno-economic analysis suggests that ~ 10-fold improvements in permeation or equivalent cost reductions are required for economic viability of this scheme.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The ion-driven permeation experiment PERMEX

A new installation PERMEX for the investigation of ion-driven permeation through metals was designed and built. A metal membrane under investigation separates two high-vacuum chambers. In the implantation chamber, the membrane surface is irradiated with a monoenergetic deuterium ion beam with an incident energy in the interval of 100-3000 eV/D. The ion flux at the surface is in a range of 10{sup 13}-2x10{sup 14} D/cm{sup 2} s, the membrane temperature can be varied in the interval of 290-1050 K. The permeating deuterium flux from the outlet membrane surface to the volume of the second chamber (registration chamber) is measured by a quadrupole mass-analyzer. The outlet surface of the membrane can be cleaned by an argon ion beam. To approve the correct work of the setup a number of experiments were performed with Ni membranes. First results of experiments with tungsten membranes are presented.

36 MATERIALS SCIENCE↗

Controlled phosphate doping into nanoscopic SiO 2 proton conducting membranes

This article describes a method to introduce phosphate (PO 4 ) into SiO 2 atomic layer deposition (ALD) films in a self-limiting fashion. The method involves the use of a less common phosphate precursor, trimethyl phosphite [P(OMe) 3 ], to introduce PO 4 as a low-level dopant, <1 at. %, into a SiO 2 ALD process using bis(ethylmethylamino)silane and a modified O 3 conversion. P(OMe) 3 does not deposit a film with typical oxygen sources but incorporates as PO 4 in an ABC-type ALD scheme at deposition temperatures ranging from 100 to 300 °C. Addition of up to ∼1 at. % of PO 4 does not significantly impact the film density or concentrations of carbon and nitrogen impurities, which are both <0.4 at. %. Despite the relatively low dopant concentrations, PO 4 incorporation is shown to have a large impact on transport properties of the film. When explored as proton (H + )-conducting membranes, undoped SiO 2 ALD films showed H + conductivities (3 × 10 −6 –8 × 10 −5 S cm −1 ) and low H 2 permeabilities (<10 −9 cm 2 s −1 ) when measured at room temperature. The addition of PO 4 is shown to increase H + conductivity to 2 × 10 −4 S cm −1 , while maintaining low H 2 permeability of <10 −9 cm 2 s −1 . The ratio of H + conductivity to H 2 permeability, a key performance metric for H + -conducting membranes used in water electrolyzers, exceeds that of commercial Nafion-117 membranes. Here, the moderate H + conductivity and very low H 2 permeability of PO 4 -doped SiO 2 films make them promising candidates as fluorine-free replacements for Nafion in applications such as water electrolysis, hydrogen fuel cells, and redox flow batteries.

Atomic layer deposition↗

Estimate of the Geothermal Energy Resource in the Major Sedimentary Basins in the United States (Presentation)

Because most sedimentary basins have been explored for oil and gas, well logs, temperatures at depth, and reservoir properties such as depth to basement and formation thickness are well known. The availability of this data reduces exploration risk and allows development of geologic exploration models for each basin. This study estimates the magnitude of recoverable geothermal energy from 15 major known U.S. sedimentary basins and ranks these basins relative to their potential. The total available thermal resource for each basin was estimated using the volumetric heat-in-place method originally proposed by (Muffler, 1979). A qualitative recovery factor was determined for each basin based on data on flow volume, hydrothermal recharge, and vertical and horizontal permeability. Total sedimentary thickness maps, stratigraphic columns, cross sections, and temperature gradient information was gathered for each basin from published articles, USGS reports, and state geological survey reports. When published data were insufficient, thermal gradients and reservoir properties were derived from oil and gas well logs obtained on oil and gas commission databases. Basin stratigraphy, structural history, and groundwater circulation patterns were studied in order to develop a model that estimates resource size, temperature distribution, and a probable quantitative recovery factor.

15 GEOTHERMAL ENERGY↗

Tritium Release Limit for Fluoride Salt-cooled High-temperature Reactors

Tritium generation is potentially a significant issue in Fluoride salt-cooled High-temperature Reactors (FHRs). Tritium in its molecular form, T{sub 2}, is highly permeable through reactor structure materials, especially under high temperatures. Since tritium presents a potential health hazard, its release must be controlled and mitigated. However, tritium release limit for FHRs is not specified in the current radiation protection regulations since FHRs are still being developed. This study first reviews related radiation protection regulations and literature before proposing a potential limit value of the tritium release rate for FHRs. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Controlling Subsurface Fractures and Fluid Flow: A Basic Research Agenda

From beneath the surface of the earth, we currently obtain about 80-percent of the energy our nation consumes each year. In the future we have the potential to generate billions of watts of electrical power from clean, green, geothermal energy sources. Our planet’s subsurface can also serve as a reservoir for storing energy produced from intermittent sources such as wind and solar, and it could provide safe, long-term storage of excess carbon dioxide, energy waste products and other hazardous materials. However, it is impossible to underestimate the complexities of the subsurface world. These complexities challenge our ability to acquire the scientific knowledge needed for the efficient and safe exploitation of its resources. To more effectively harness subsurface resources while mitigating the impacts of developing and using these resources, the U.S. Department of Energy established SubTER – the Subsurface Technology and Engineering RD&D Crosscut team. This DOE multi-office team engaged scientists and engineers from the national laboratories to assess and make recommendations for improving energy-related subsurface engineering. The SubTER team produced a plan with the overall objective of “adaptive control of subsurface fractures and fluid flow.”This plan revolved around four core technological pillars—Intelligent Wellbore Systems that sustain the integrity of the wellbore environment; Subsurface Stress and Induced Seismicity programs that guide and optimize sustainable energy strategies while reducing the risks associated with subsurface injections; Permeability Manipulation studies that improve methods of enhancing, impeding and eliminating fluid flow; and New Subsurface Signals that transform our ability to see into and characterize subsurface systems. The SubTER team developed an extensive R&D plan for advancing technologies within these four core pillars and also identified several areas where new technologies would require additional basic research. In response, the Office of Science, through its Office of Basic Energy Science (BES), convened a roundtable consisting of 15 national lab, university and industry geoscience experts to brainstorm basic research areas that underpin the SubTER goals but are currently underrepresented in the BES research portfolio. Held in Germantown, Maryland on May 22, 2015, the round-table participants developed a basic research agenda that is detailed in this report. Highlights include the following: -A grand challenge calling for advanced imaging of stress and geological processes to help understand how stresses and chemical substances are distributed in the subsurface—knowledge that is critical to all aspects of subsurface engineering; -A priority research direction aimed at achieving control of fluid flow through fractured media; -A priority research direction aimed at better understanding how mechanical and geochemical perturbations to subsurface rock systems are coupled through fluid and mineral interactions; -A priority research direction aimed at studying the structure, permeability, reactivity and other properties of nanoporous rocks, like shale, which have become critical energy materials and exhibit important hallmarks of mesoscale materials; -A cross-cutting theme that would accelerate development of advanced computational methods to describe heterogeneous time-dependent geologic systems that could, among other potential benefits, provide new and vastly improved models of hydraulic fracturing and its environmental impacts; -A cross-cutting theme that would lead to the creation of “geo-architected materials” with controlled repeatable heterogeneity and structure that can be tested under a variety of thermal, hydraulic, chemical and mechanical conditions relevant to subsurface systems; -A cross-cutting theme calling for new laboratory studies on both natural and geo-architected subsurface materials that deploy advanced high-resolution 3D imaging and chemical analysis methods to determine the ;rates and mechanisms of fluid-rock processes, and to test predictive models of such phenomena. Many of the key energy challenges of the future demand a greater understanding of the subsurface world in all of its complexity. This greater under- standing will improve the ability to control and manipulate the subsurface world in ways that will benefit both the economy and the environment. This report provides specific basic research pathways to address some of the most fundamental issues of energy-related subsurface engineering.

15 GEOTHERMAL ENERGY↗

Glomerular filtration drug injury: In vitro evaluation of functional and morphological podocyte perturbations

Highlights: • The use of nephrotoxic drugs is often unavoidable. • Human podocyte cell line allows the study of the simplified glomerular filtration. • Filtration perturbations are correlated with morphological and phenotypic changes. • Functional and morphological tests are interesting tools for drug screening. The kidney is an organ that plays a major role in the excretion of numerous compounds such as drugs and chemicals. However, a great number of pharmacological molecules are nephrotoxic, affecting the efficiency of the treatment and increasing morbidity or mortality. Focusing on glomerular filtration, we propose in this study a simple and reproducible in vitro human model that is able to bring to light a functional podocyte injury, correlated with morphologic/phenotypic changes after drug exposure. This model was used for the evaluation of paracellular permeability of FITC-dextran molecules as well as FITC-BSA after different treatments. Puromycin aminonucleoside and adriamycin, compounds known to induce proteinuria in vivo and that serve here as positive nephrotoxic drug controls, were able to induce an important increase in fluorescent probe passage through the cell monolayer. Different molecules were then evaluated for their potential effect on podocyte filtration. Our results demonstrated that a drug effect could be time dependent, stable or scalable and relatively specific. Immunofluorescence studies indicated that these functional perturbations were due to cytoskeletal perturbations, monolayer disassembly or could be correlated with a decrease in nephrin expression and/or ZO-1 relocation. Taken together, our results demonstrated that this in vitro human model represents an interesting tool for the screening of the renal toxicity of drugs.

60 APPLIED LIFE SCIENCES↗

A phase field framework for capillary-induced fracture in unsaturated porous media: Drying-induced vs. hydraulic cracking

This work introduces a unified mathematical framework to replicate both desiccation-induced and hydraulic fracturing in low-permeable unsaturated porous materials observed in experiments. The unsaturated porous medium is considered as a three-phase solid–liquid–gas effective medium of which each constituent occupies a fraction of the representative elementary volume. As such, an energy-minimization-based phase-field model (PFM) is formulated along with the Biot’s poroelasticity theory to replicate the sub-critical crack growth in the brittle regime. Unlike hydraulic fracturing where the excess pore liquid pressure plays an important role at the onset and propagation of cracks, desiccation cracks are mainly driven by deformation induced by water retention. Therefore, the wettability of the solid skeleton may affect the evolution of the capillary pressure (suction) and change the path-dependent responses of the porous media. This air–water–solid interaction may either hinder or enhance the cracking occurrence. This difference of capillary effect on crack growth during wetting and drying is replicated by introducing retention-sensitive degradation mechanisms in our phase field fracture approach. To replicate the hydraulic behaviors of the pore space inside the host matrix and that of the cracks, the path-dependent changes of the intrinsic permeability due to crack growth and porosity changes are introduced to model the flow conduit in open and closed cracks. Numerical examples of drying-induced and hydraulic fracturing demonstrate the capability of the proposed model to capture different fracture patterns, which qualitatively agrees with the fracture mechanisms of related experiments documented in the literature.

42 ENGINEERING↗

Initial Simulations of Empty Room Collapse and Reconsolidation at the Waste Isolation Pilot Plant

The Waste Isolation Pilot Plant (WIPP) is a geologic repository for defense-related nuclear waste. If left undisturbed, the virtually impermeable rock salt surrounding the repository will isolate the nuclear waste from the biosphere. If humans accidentally intrude into the repository in the future, then the likelihood of a radionuclide release to the biosphere will depend significantly on the porosity and permeability of the repository itself. Room ceilings and walls at the WIPP tend to collapse over time, causing rubble piles to form on floors of empty rooms. The surrounding rock formation will gradually compact these rubble piles until they eventually become solid salt, but the length of time for a rubble pile to reach a certain porosity and permeability is unknown. This report details the first efforts to build models to predict the porosity and permeability evolution of an empty room as it closes. Conventional geomechanical numerical methods would struggle to model empty room collapse and rubble pile consolidation, so three different meshless methods, the Immersed Isogeometric Analysis Meshfree, Reproducing Kernel Particle Method (RKPM), and the Conformal Reproducing Kernel method, were assessed. First, the meshless methods and the finite element method each simulated gradual room closure, without ceiling or wall collapse. All three methods produced equivalent room closure predictions with comparable computational speed. Second, the Immersed Isogeometric Analysis Meshfree method and RKPM simulated two-dimensional empty room collapse and rubble pile consolidation. Both methods successfully simulated large viscoplastic deformations, fracture, and rubble pile rearrangement to produce qualitatively realistic results. In addition to geomechanical simulations, the flow channels in damaged salt and crushed salt were measured using micro-computed tomography, and input into a computational fluid dynamics simulation to predict the salt's permeability. Although room for improvement exists, the current simulation approaches appear promising.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Epistatic mutations in PUMA BH3 drive an alternate binding mode to potently and selectively inhibit anti-apoptotic Bfl-1

Overexpression of anti-apoptotic Bcl-2 family proteins contributes to cancer progression and confers resistance to chemotherapy. Small molecules that target Bcl-2 are used in the clinic to treat leukemia, but tight and selective inhibitors are not available for Bcl-2 paralog Bfl-1. Guided by computational analysis, we designed variants of the native BH3 motif PUMA that are > 150-fold selective for Bfl-1 binding. The designed peptides potently trigger disruption of the mitochondrial outer membrane in cells dependent on Bfl-1, but not in cells dependent on other anti-apoptotic homologs. High-resolution crystal structures show that designed peptide FS2 binds Bfl-1 in a shifted geometry, relative to PUMA and other binding partners, due to a set of epistatic mutations. FS2 modified with an electrophile reacts with a cysteine near the peptide-binding groove to augment specificity. Designed Bfl-1 binders provide reagents for cellular profiling and leads for developing enhanced and cell-permeable peptide or small-molecule inhibitors.

59 BASIC BIOLOGICAL SCIENCES↗

Eicosapentaenoic acid (EPA) induced apoptosis in HepG2 cells through ROS–Ca{sup 2+}–JNK mitochondrial pathways

Highlights: • EPA evoked ROS formation, [Ca{sup 2+}]{sub c} accumulation, the opening of MPTP and the phosphorylation of JNK. • EPA-induced [Ca{sup 2+}]{sub c} elevation was depended on production of ROS. • EPA-induced ROS generation, [Ca{sup 2+}]{sub c} increase, and JNK activated caused MPTP opening. • The apoptosis induced by EPA was related to release of cytochrome C through the MPTP. • EPA induced HepG2 cells apoptosis through ROS–Ca{sup 2+}–JNK mitochondrial pathways. - Abstract: Eicosapentaenoic acid (EPA), a well-known dietary n−3 PUFAS, has been considered to inhibit proliferation of tumor cells. However, the molecular mechanism related to EPA-induced liver cancer cells apoptosis has not been reported. In this study, we investigated the effect of EPA on HepG2 cells proliferation and apoptosis mechanism through mitochondrial pathways. EPA inhibited proliferation of HepG2 cells in a dose-dependent manner and had no significant effect on the cell viability of humor normal liver L-02 cells. It was found that EPA initially evoked ROS formation, leading to [Ca{sup 2+}]{sub c} accumulation and the mitochondrial permeability transition pore (MPTP) opening; EPA-induced HepG2 cells apoptosis was inhibited by N-acetylcysteine (NAC, an inhibitor of ROS), 1,2-bis (2-aminophenoxy) ethane-N,N,N′,N′-tetraacetic acid (BAPTA-AM, a chelator of calcium) and CsA (inhibitor of MPTP). The relationship between ROS production, the increase of cytoplasmic Ca and MPTP opening was detected. It seems that ROS may act as an upstream regulator of EPA-induced [Ca{sup 2+}]{sub c} generation, moreover, generation of ROS, overload of mitochondrial [Ca{sup 2+}]{sub c}, and JNK activated cause the opening of MPTP. Western blotting results showed that EPA elevated the phosphorylation status of JNK, processes associated with the ROS generation. Simultaneously, the apoptosis induced by EPA was related to release of cytochrome C from mitochondria to cytoplasm through the MPTP and activation of caspase-9 and caspase-3. These results suggest that EPA induces apoptosis through ROS–Ca{sup 2+}–JNK mitochondrial pathways.

60 APPLIED LIFE SCIENCES↗

CO-releasing molecules-2 attenuates ox-LDL-induced injury in HUVECs by ameliorating mitochondrial function and inhibiting Wnt/β-catenin pathway

Oxidized low-density lipoprotein (ox-LDL) is well known to disrupt normal functionality of endothelium, which plays a prominent role in endothelial dysfunction in many cardiovascular diseases. CO-releasing molecule 2 (CORM-2) is a promising candidate for treatment of cardiovascular diseases. However, it has not been defined whether CORM-2 might improve endothelial injury induced by ox-LDL. The present study was undertaken to determine the regulatory role of CORM-2 in cell injury of ox-LDL-treated human umbilical vein endothelial cells (HUVECs). Our results showed that ox-LDL inhibited the cell proliferation, but promoted apoptosis and release of cytochrome c (cytc) from mitochondrion into cytoplasm, stimulated the cleavage of caspase-3 and mitochondrial permeability transition pore (MPTP) opening. In addition, ox-LDL-incubated HUVECs exhibited excessive reactive oxygen species (ROS), increased protein levels of NADPH oxidase subunits p22{sup phox}, p47{sup phox}, NOX-2 and activation of Wnt/β-catenin signaling pathway. However, pretreatment with CORM-2 significantly reduced cell apoptosis, release of cytc from mitochondrion into cytoplasm, MPTP opening and cleavage of caspase-3, suppressed the superoxide anion generation and Wnt/β-catenin pathway activation in HUVECs response to ox-LDL. Collectively, we provide the evidence that CORM-2 attenuated ox-LDL-mediated endothelial apoptosis and oxidative stress by recovering the mitochondrial function and blocking Wnt/β-catenin pathway. - Highlights: • CORM-2 ameliorated ox-LDL-induced apoptosis, mitochondrial damage, and Wnt/β-catenin activation in HUVECs. • CORM-2 is potential therapeutic agent against endothelial dysfunction-related diseases.

60 APPLIED LIFE SCIENCES↗

Advective gas flow in bentonite: Development and comparison of enhanced multi-phase numerical approaches

Understanding the impact of repository gas, generated from degradation of waste and its interaction with the host rock, is essential when assessing the performance and safety function of long-term disposal systems for radioactive waste. Numerical models based on conventional multi-phase flow theory have historically been applied to predict the outcome and impact of gas flow on different repository components. However, they remain unable to describe the full complexity of the physical processes observed in water-saturated experiments (e.g., creation of dilatant pathways) and thus, the development of novel representations for their description is required when assessing fully saturated clay-based systems. This was the primary focus of Task A within the international cooperative project DECOVALEX-2019 (D-2019) and refinement of these approaches is the primary focus of this study (Task B in the current phase of DECOVALEX-2023). This paper summarises development of enhanced numerical representations of key processes and compares the performance of each model against high-quality laboratory test data. Experimental data reveals that gas percolation in water-saturated compacted bentonite is characterised by four key features: (i) a quiescence phase, followed by (ii) the gas breakthrough, which leads to a (iii) peak value, which is then followed by (iv) a negative decay. Three models based on the multiphase flow theory have been developed. These models can provide good initial values and reasonable responses for gas breakthrough (although some of them still predict a too-smooth response). Peak gas pressure values are in general reasonably well captured, although maximum radial stress differences are observed at 48 mm from the base of the sample. Here, numerical peak values of 12.8 MPa are predicted, whereas experimental values are about 11 MPa. These models are also capable of providing a reasonable representation of the negative pressure decay following peak pressure. However, other key specific features (such as the timing of gas breakthrough) still require a better representation. The model simulations and their comparison with experimental data show that these models need to be further improved with respect to model parameter calibration, the numerical representation of spatial heterogeneities in material properties and flow localisation, and the upscaling of the related physical processes and parameters. To further understand gas flow localisation, a new conceptual model has been developed, which shows that discrete channels can possibly be induced through the instability of gas-bentonite interface during gas injection, thus providing a new perspective for modeling gas percolation in low-permeability deformable media.

58 GEOSCIENCES↗

Carbon dioxide dissolution in structural and stratigraphic traps

Abstract The geologic sequestration of carbon dioxide ( CO 2 ) in structural and stratigraphic traps is a viable option to reduce anthropogenic emissions. While dissolution of the CO 2 stored in these traps reduces the long-term leakage risk, the dissolution process remains poorly understood in systems that reflect the appropriate subsurface geometry. In this work, we study dissolution in a porous layer that exhibits a feature relevant for CO 2 storage in structural and stratigraphic traps: a finite CO 2 source along the top boundary that extends only part way into the layer. This feature represents the finite extent of the interface between free-phase CO 2 pooled in a trap and the underlying brine. Using theory and simulations, we describe the dissolution mechanisms in this system for a wide range of times and Rayleigh numbers, and classify the behaviour into seven regimes. For each regime, we quantify the dissolution flux numerically and model it analytically, with the goal of providing simple expressions to estimate the dissolution rate in real systems. We determine that, at late times, the dissolution flux decreases relative to early times as the flow of unsaturated water to the CO 2 source becomes constrained by a lateral exchange flow though the reservoir. Application of the models to several representative reservoirs indicates that dissolution is strongly affected by the reservoir properties; yet, we find that reservoirs with high permeabilities ( $k\geq 1$ Darcy) that are tens of metres thick and several kilometres wide could potentially dissolve hundreds of megatons of CO 2 in tens of years.

42 ENGINEERING↗

Structure and proton conduction in sulfonated poly(ether ether ketone) semi-permeable membranes: a multi-scale computational approach.

The design of polymeric membranes for proton or ionic exchange highly depends on the fundamental understanding of the physical and molecular mechanisms that control the formation of the conduction channels. There is an inherent relation between the dynamical structure of the polymeric membrane and the electrostatic forces that drive membrane segregation and proton transport. Here, we used a multi-scale computational approach to analyze the morphology of sulfonated poly(ether ether ketone) membranes at the mesoscale. A self-consistent description of the electrostatic phenomenon was adopted, where discrete polymer chains and a continuum proton field were embedded in a continuum fluid. Brownian dynamics was used for the evolution of the suspended polymer molecules, while a convection-diffusion transport equation, including the Nernst-Planck diffusion mechanism, accounted for the dynamics of the proton concentration field. We varied the polymer concentration, the degree of sulfonation and the level of confinement to find relationships between membrane structure and proton conduction. Our results indicate that the reduced mobility of polymer chains, at concentrations above overlap, and a moderate degree of sulfonation -i.e., 30% - are essential elements for membrane segregation and proton domain connectivity. These conditions also ensure that the membrane structure is not affected by size or by potential gradients. Importantly, our analysis shows that membrane conductivity and current are linearly dependent on polymer concentration and quadratically dependent on the degree of sulfonation. We found that the optimal polymeric membrane design requires a polymer concentration above overlap and a degree of sulfonation around 50%. These conditions promote a dynamical membrane morphology with a constant density of proton channels. Our results and measurements agree with previous experimental works, thereby validating our model and observations.

Molina, Jarol↗

Poly(cyclohexadiene)-Based Polymer Electrolyte Membranes for Fuel Cell Applications

The goal of this research project was to create and develop fuel cell membranes having high proton conductivity at high temperatures and high chemical and mechanical durability. Poly(1,3-cyclohexadiene) (PCHD) is of interest as an alternative polymer electrolyte membrane (PEM) material due to its ring-like structure which is expected to impart superior mechanical and thermal properties, and due to the fact that PCHD can readily be incorporated into a range of homopolymer and copolymer structures. PCHD can be aromatized, sulfonated, or fluorinated, allowing for tuning of key performance structure and properties. These factors include good proton transport, hydrophilicity, permeability (including fuel gas impermeability), good mechanical properties, morphology, thermal stability, crystallinity, and cost. The basic building block, 1,3-cyclohexadiene, is a hydrocarbon monomer that could be inexpensively produced on a commercial scale (pricing typical of other hydrocarbon monomers). Optimal material properties will result in novel low cost PEM membranes engineered for high conductivity at elevated temperatures and low relative humidities, as well as good performance and durability. The primary objectives of this project were: (1) To design, synthesize and characterize new non-Nafion PEM materials that conduct protons at low (25-50%) RH and at temperatures ranging from room temperature to 120 C; and (2) To achieve these objectives, a range of homopolymer and copolymer materials incorporating poly(cyclohexadiene) (PCHD) will be synthesized, derivatized, and characterized. These two objectives have been achieved. Sulfonated and crosslinked PCHD homopolymer membranes exhibit proton conductivities similar to Nafion in the mid-RH range, are superior to Nafion at higher RH, but are poorer than Nafion at RH < 50%. Thus to further improve proton conductivity, particularly at low RH, poly(ethylene glycol) (PEG) was incorporated into the membrane by blending and by copolymerization. Conductivity measurements at 120 C over RH ranging from 20 to 100% using the BekkTech protocol showed much improved proton conductivities. Conductivities for the best of these new membranes exceed the DOE Year 3 milestone of 100 mS/cm at 50% RH at 120 C. Further optimization of these very promising low cost membranes could be pursued in the future.

08 HYDROGEN↗

Aging Exacerbates Neuroinflammatory Outcomes Induced by Acute Ozone Exposure

The role of environmental stressors, particularly exposure to air pollution, in the development of neurodegenerative disease remains underappreciated. We examined the neurological effects of acute ozone (O 3 ) exposure in aged mice, where increased blood brain barrier (BBB) permeability may confer vulnerability to neuroinflammatory outcomes. C 57 BL/6 male mice, aged 8-10 weeks or 12–18 months were exposed to either filtered air (FA) or 1.0 ppm O 3 for 4 hours; animals received a single IP injection of sodium fluorescein (FSCN) 20 hours post-exposure. One-hour post-FSCN injection, animals were transcardially perfused for immunohistochemical analysis of BBB permeability. β-amyloid protein expression was assessed via ELISA. Flow cytometric characterization of infiltrating immune cells, including neutrophils, macrophages, and microglia populations was performed 20 hours post-O 3 exposure. Flow cytometry analysis of brains revealed increased microglia “activation” and presentation of CD11b, F4/80 and MHCII in aged animals relative to younger ones; these age-induced differences were potentiated by acute O 3 exposure. Cortical and limbic regions in aged brains had increased reactive microgliosis and β-amyloid protein expression after O 3 insult. The aged cerebellum was particularly vulnerable to acute O 3 exposure with increased populations of infiltrating neutrophils, peripheral macrophages/monocytes, and Ly6C + inflammatory monocytes after insult, which were not significantly increased in the young cerebellum. O 3 exposure increased the penetration of FSCN beyond the BBB, the infiltration of peripheral immune cells, and reactive gliosis of microglia. Furthermore, the aged BBB is vulnerable to insult and becomes highly penetrable in response to O 3 exposure, leading to greater neuroinflammatory outcomes.

60 APPLIED LIFE SCIENCES↗

Common-mode inductor saturation analysis and design optimization based on spectrum concept

Understanding the CM inductor core saturation mechanism and reducing core flux density is critical for CM inductor design optimization. Instead of a time domain method, this paper introduces frequency domain spectrum concept for CM inductor core saturation analysis and design optimization, which will provide designers a better understanding of CM inductor design. First, both core permeability and converter modulation index's opposite influence on DM flux density and CM flux density are identified. Then, CM flux density is further investigated based on the spectrum concept. Three components in the CM inductor which may cause large CM flux density and core saturation are summarized: (1) switching frequency related components, (2) impedance resonance frequency related components, and (3) modulation frequency related components. Each component is investigated for CM flux density reduction and filter design optimization. A connecting AC and DC side midpoint with notch filter structure is proposed to reduce modulation frequency related components. Experiment results are presented to verify the proposed concept and method.

Chen, Ruirui↗