Search NASA⌕ Search

SEARCH · Search NASA

Results for “Sintering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

Effect of ZnO addition on the sintering and electrical properties of (Mn,W)-doped PZT-PMS-PZN ceramics

The effect of ZnO addition on the phase structure, microstructure and dielectric and piezoelectric properties of 0.2 wt.% MnO{sub 2} and 0.6 wt.% WO{sub 3}-doped Pb(Zr{sub 0.52}Ti{sub 0.48})O{sub 3}-Pb(Mn{sub 1/3}Sb{sub 2/3})O{sub 3}-Pb(Zn{sub 1/3}Nb{sub 2/3})O{sub 3} (PZT-PMS-PZN) ceramics was investigated. X-ray diffraction shows that the phase structure of ceramics is transformed from rhombohedral to tetragonal with the increasing of ZnO addition. The bulk density significantly increases when ZnO is added and then it slightly decreases for ZnO addition above 0.2 wt.%. SEM micrographs show the grains of ceramics are uniform and well developed by adding 0.1 wt.% ZnO. The Curie temperature (T{sub c}) of 270 deg. C is obtained at the 0.1 wt.% ZnO addition. Mechanical quality factor (Q{sub m}), electromechanical coupling factor (K{sub p}) and piezoelectric constant (d{sub 33}) increase firstly, and then decrease with the increasing of ZnO addition, while dielectric loss tan {delta} drops all the time. The Q{sub m}, K{sub p}, d{sub 33}, tan {delta} and T{sub c} of the ceramics show the optimum values of 1899, 0.55, 300 (pC/N), 0.0063 and 270 deg. C, respectively, at the lower sintering temperature of 1120 deg. C and with 0.1 wt.% ZnO addition.

36 MATERIALS SCIENCE↗

Dislocation density in fine grain-size spark-plasma sintered aluminum measured using high brightness synchrotron radiation

In this study, three-dimensional orientation mapping of samples of aluminum prepared by spark plasma sintering (SPS) with average grain sizes of 5 μm and 1 μm has been carried out using high-brightness synchrotron radiation, from which the geometrically necessary dislocation (GND) density has been determined. The low average measured GND density values confirm that the SPS process can be used to produce samples containing grains with dislocation density similar to that of fully recrystallized coarse-grained samples. Values of GND density are also compared to those obtained from electron back-scatter diffraction studies on the same material, highlighting the significantly higher angular resolution of the synchrotron data. For the 5 μm grain-size sample the measured GND density can account for a large fraction of the previously observed positive Hall-Petch deviation of this material. For the 1 μm grain-size sample, however, the GND-based strengthening contribution is much smaller than the reported positive Hall-Petch deviation, such that the additional strength may be reliably associated with dislocation source-limited strengthening.

36 MATERIALS SCIENCE↗

Solid-state reaction mediated microstructural evolution in a spark plasma sintered in situ Ti–B 4 C composite

For this study, a novel porosity-free in situ Ti–B 4 C composite was fabricated via spark plasma sintering (SPS). Detailed analysis of the phase evolution, coupling results from XRM, XRD and SEM-EBSD-EDS, indicate that primarily TiB 2 precipitates formed due to the in-situ reactions between the boron-carbide and titanium powders. The precipitation of TiB 2 resulted in the formation of a graphitic C-rich thin layer circumscribing the partially reacted B 4 C particles. Further progression of the in-situ reaction leads to the out-diffusion of the excess carbon from the B 4 C particles, across the graphite and TiB 2 phases, forming TiC upon reacting with the titanium matrix. Therefore, the final microstructure primarily consisted of TiB 2 , TiC, and partially reacted B 4 C phases, with small amounts of TiB, α-Ti, and graphite. Furthermore, the microstructure in these SPS processed in situ composites appeared to be the product of a solid-state Ti–B 4 C diffusion couple, substantially different from their fusion-based additively manufactured counterparts. Nano-indentation tests revealed a remarkably high average hardness of ~25 GPa for this SPS-processed Ti–B 4 C composite and comparable (with literature) phase-specific hardness and modulus values for the constituent TiB 2 , TiC, and B 4 C phases.

36 MATERIALS SCIENCE↗

Electric-field-assisted-sintering of rare-earth oxide dispersion strengthened Fe-Cr-Mo alloys

Oxide dispersion-strengthened (ODS) alloys are widely recognized for their exceptional high-temperature strength, creep resistance, and radiation tolerance, making them indispensable for advanced nuclear reactors, aerospace, and energy systems. Achieving a fine and stable dispersion of oxide nanoparticles is critical, as these particles act as strong barriers to dislocation motion and effective sinks for irradiation-induced defects, ensuring structural integrity under extreme conditions. Here, in this study, Fe–Cr–Mo-based ODS alloys were fabricated via mechanical alloying and consolidated using electric-field-assisted sintering (EFAS) with additions of Y 2 O 3 , La 2 O 3 , and CeO 2 . EFAS processing produced ultrafine-grained microstructures (average grain size <1 μm) with uniformly distributed oxide clusters (2–4 nm). Atom probe tomography revealed that La 2 O 3 -containing alloys exhibited the highest nanoparticle number density, resulting in superior tensile strength compared to yttria- and ceria-bearing counterparts. The combined effect of grain refinement and rare-earth oxide dispersion significantly enhanced mechanical performance, demonstrating the potential of EFAS for developing high-strength ferritic alloys for demanding environments such as nuclear systems.

36 - MATERIALS SCIENCE↗

Amorphous complexion-aided sintering enables scalable processing of bulk nanocrystalline Cu-Zr with high strength and compressive plasticity

Nanocrystalline alloys can have exceptional strengths, yet due to limited microstructural stability it is difficult to fabricate bulk pieces through traditional processing routes that retain nanosized grains. In this study, centimeter-sized Cu-Zr alloy pellets were fabricated via a simple and improved powder metallurgy processing route. Different consolidation temperatures and times were employed to investigate the effect of amorphous grain boundary complexions on densification and the resulting mechanical properties. Bulk compression tests were carried out, with the samples that were hot pressed at 900 °C for 10 h exhibiting an excellent combination of average yield strength of 722 ± 45 MPa and average failure strain of 25.3 ± 2.4 %. Furthermore, we find that a powder processing route which enables amorphous complexion-assisted sintering leads to samples that (1) reach full density without requiring quenching treatments or other complex processing, (2) demonstrate appreciable plasticity, and (3) have strength that competes with commercially available high-strength Cu alloys.

Bulk nanocrystalline alloy↗

Radiative Properties of Coal Ash Deposits with Sintering Effects

The heat-transfer characteristics in the fireside of a pulverized-coal furnace are affected, among other factors, by the physical and chemical characteristics of the ash deposits. Indeed, the physical state of the ash deposits and their chemical composition determine the radiative and conductive properties of the furnace walls. Particularly, several complex mechanisms are involved in the radiative heat-transfer process at the walls that restricts the absorption of the incident radiation of the flame, particles, and hot gases. These mechanisms involve dependencies on the radiation spectrum due to the ash chemical composition and ash-sintering effects that enhance or hinder the overall heat transfer. In this work, the complex mechanisms that describe the heat exchange in the presence of ash deposits and their impact on the prediction of the wall emissivity and ultimately the wall heat transfer in a real system are discussed.

01 COAL, LIGNITE, AND PEAT↗

Pelletization with Spark Plasma Sintering and Characterization of Metal Iodides: An Assessment of Long-Term Radioiodine Immobilization Options

Four promising iodine “getter” materials (Ag, Cu, Bi, and Sn) for radioiodine capture were assessed in their pure metal-iodide (MI x ) pelletized forms to compare relative chemical durabilities. To study chemical durability, commercial MI x compounds of AgI, BiI 3 , BiOI, CuI, and SnI 4 were converted to dense monolithic pellets using spark plasma sintering. Semidynamic leach testing in the form of modified ASTM C1308 tests was then performed on the pellets in two different forms including unmounted (as-pressed) specimens (i.e., “U”) and epoxy-mounted specimens (i.e., “M”) with polished surfaces. The chemical durability results and sample characterizations showed that three of the five MI x compounds tested (i.e., AgI, CuI, and BiOI) displayed moderate to high leach resistances. Further, the remaining two MI x compounds (i.e., BiI 3 and SnI 4 ), which are both desirable iodine waste forms due to their high iodine loading capacities, readily decomposed during leach testing, indicated by crystallographic changes in the specimens as well as large amounts of iodine detected in the leachate solutions. The instabilities of BiI 3 and SnI 4 raise uncertainties for using the base metals/cations (i.e., Bi 0 /Bi 3+ and Sn 0 /Sn 4+ , respectively) as viable getters for radioiodine capture due to likely poor waste form chemical durabilities after capture and consolidation into waste forms.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Toward the Design of a Hierarchical Perovskite Support: Ultra-Sintering-Resistant Gold Nanocatalysts for CO Oxidation

We report that an ultrastable Au nanocatalyst based on a heterostructured perovskite support with high surface area and uniform LaFeO 3 nanocoatings was successfully synthesized and tested for CO oxidation. Strikingly, small Au nanoparticles (4–6 nm) are obtained after calcination in air at 700 °C and under reaction conditions. The designed Au catalyst not only possessed extreme sintering resistance but also showed high catalytic activity and stability because of the strong interfacial interaction between Au and the heterostructured perovskite support.

36 MATERIALS SCIENCE↗

Effect of fly ash on catalytic removal of gaseous dioxins over V{sub 2}O{sub 5}-WO{sub 3} catalyst of a sinter plant

A PCDD/F (polychlorinated dibenzo-p-dioxin and dibenzofuran)-containing gas stream generating system was developed to investigate the efficiency and effectiveness of V{sub 2}O{sub 5}-WO{sub 3} catalyst for PCDD/F destruction. Catalytic decomposition of PCDD/Fs (simulated gas streams) was evaluated with lab-scale pelletized and plate-type catalyst based on V{sub 2}O{sub 5}-WO{sub 3}/TiO{sub 2} at controlled temperature, space velocity, and inlet PCDD/F concentration. Due to the lower porosity of the pelletized catalyst, PCDD/F destruction efficiencies reach 72.9-83.2% for different levels of inlet PCDD/F concentrations (1.08-3.04 ng-TEQ/Nm{sup 3}) of the gas stream (space velocity: 5000 h-1). As the surface area is increased from 287 m{sup 2}/m{sup 3} (plate-type A) to 550 m{sup 2}/m{sup 3} (plate-type B), the PCDD/F destruction achieved with plate-type catalyst increases from 76.0% to 85.3% at 320{sup o}C (space velocity: 5000 h{sup -1}). In addition, the results of pilot-scale experiment (real flue gases of a sinter plant) indicate that relatively lower PCDD/F destruction efficiencies (62.1-65.7%) were achieved with the plate-type B catalyst as the solid-phase PCDD/F and fly ash passed through the reactor (space velocity: 5000 h{sup -1}). Overall, the lab-scale and pilot-scale experiments indicate that PCDD/F destructions achieved with pelletized and plate-type catalysts strongly depend on the operating temperature of the catalyst. The results also indicate that the presence of fly ash lowers PCDD/F destruction due to significant PCDD/F formation via de novo synthesis at 320{sup o}C. 20 refs., 5 figs., 3 tabs.

01 COAL, LIGNITE, AND PEAT↗

Spark plasma sintering-fabricated one-dimensional nanoscale 'crystalline-amorphous' carbon heterojunction

One-dimensional (1D) nanoscale 'crystalline-amorphous' carbon heterojunction is fabricated by post-treatment of an amorphous carbon nanofiber in a spark plasma sintering (SPS) system. It is proposed that the unique SPS process is responsible for the heterojunction formation. Studies of the electrical transport property show that the nanoscale heterojunction exhibits a typical rectification behavior. The heterojunctions may have broad potential applications in nanoelectronics and optoelectronics and the SPS technique could be a distinctive approach to construct 1D functional nanomaterials with high throughput.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Large-size ultrahigh strength Ni-based bulk metallic glassy matrix composites with enhanced ductility fabricated by spark plasma sintering

Ni-based bulk glassy alloy composites (GACs) simultaneously with ultrahigh strength and enhanced ductility and satisfying large-size requirements were fabricated by spark plasma sintering of gas-atomized Ni{sub 52.5}Nb{sub 10}Zr{sub 15}Ti{sub 15}Pt{sub 7.5} glassy alloy powder blend with ceramic or metal powders. No crystallization of metallic glassy matrix and good bonding state between the particles are responsible for good mechanical properties of the fabricated bulk GACs. The improvement of plastic ductility of the fabricated bulk GACs originates from the structural inhomogeneity caused by the particles inclusion. The additional particulates act as a resisting media causing deviation, branching, and multiplication of shear bands.

36 MATERIALS SCIENCE↗

Structure and magnetic properties of bulk nanocrystalline Dy metal prepared by spark plasma sintering

The structure and magnetic properties were studied for bulk nanocrystalline dysprosium (Dy) metal prepared by spark plasma sintering method. All the as-prepared samples have hexagonal close packed structure. A decrease in grain size results in remarkable changes in magnetic ordering temperature of the nanocrystalline Dy metal. At 5 K, the magnetization drops by 3.35%, and the coercive force increases by three times for nanocrystalline Dy compared to those of coarse-grained bulk Dy sample. These results indicate the remarkable influence of the nanostructure on the magnetism of Dy due to finite size effect.

36 MATERIALS SCIENCE↗

A high-resolution field-emission-gun, scanning electron microscope investigation of anisotropic hydrogen decrepitation in Nd-Fe-B-based sintered magnets

In this investigation commercial magnets based on (Nd,Dy){sub 14}(Fe,Co){sub 79}B{sub 7} were prepared by a conventional powder-metallurgy route with a degree of alignment equal to {approx}90% and then exposed to hydrogen at a pressure of 1 bar. The magnets, in the form of cylinders, were observed to decrepitate exclusively from the ends. High-resolution electron microscopy was able to identify the presence of crack formation within the Nd{sub 2}Fe{sub 14}B grains, with the cracks running parallel to the c axis of these grains. Based on the concentration profile for hydrogen in a rare-earth transition-metal material, it is clear that the presence of hydrogen-induced cracks running perpendicular to the ends of the magnet provides for a much more rapidly progressing hydrogen front in this direction than from the sides of the magnet. This results in the magnet exhibiting a macroscopic tendency to decrepitate from the poles of the magnet toward the center. This combination of microstructural modification via particle alignment as part of the sintering process and direct observation via high-resolution electron microscopy has led to a satisfying explanation for the anisotropic hydrogen-decrepitation effect.

36 MATERIALS SCIENCE↗

Study on corrosion behaviors of sintered Nd-Fe-B magnets in different environmental conditions

Nd-Fe-B magnets have outstanding magnetic properties, but their corrosion resistance is poor because the rare-earth-rich phases in them are easily oxidized. In this article, we report an investigation of the corrosion behaviors of sintered Nd-Fe-B magnets with varied compositions in different corrosion conditions. The weight losses of the magnets after corrosion testing were measured after brushing off the corrosion products. The magnetic flux losses of the magnets were measured using a fluxmeter. A scanning electron microscope equipped with an energy dispersive x-ray analysis system was employed to observe the corrosion morphology. It was found that the humid-heat resistance of the magnets was obviously improved by partially substituting Dy for Nd and adding minor Co. The corrosion products and morphologies of Nd-Fe-B magnets for the autoclave test were different from those for the constant humid-heat test. The corrosion rates of the magnets for the former were much slower than for the latter; this is probably because the high-pressure steam led to an oxygen-deficient atmosphere, and the liquid film on the surface of the magnet specimens hindered the diffusion of oxygen into the bulk for the autoclave test.

36 MATERIALS SCIENCE↗

Magnetization reversal mechanism of a sintered Nd-Fe-B magnet with Dy segregation

The magnetization reversal mechanism of a sintered Nd-Fe-B magnet with Dy segregation near grain boundaries (GB) was studied using spin polarized scanning electron spectroscopy and magnetization measurements. More fine magnetic domains near GB were found in the magnet with Dy segregation than in the magnet without treatment. Magnetic modifications near the GB had no effect on the magnetization development. The domain wall motion of a quasihard magnetic component in the magnet with Dy segregation was suppressed in comparison with those in the magnet without treatment; this could also be confirmed in the different behaviors of asymmetry components toward a magnetic field direction between both magnets. From analyzing the probability of rotating magnetization near the GB, the magnetization reversal of the magnet with Dy segregation was more difficult to produce than those of the magnet without treatment.

36 MATERIALS SCIENCE↗

Temperature dependence of magnetic behaviour in very fine grained, spark plasma sintered NiCuZn ferrites

Recently, using spark plasma sintering technique, a family of very fine grained, fully dense NiCuZn ferrites have been produced, which show constant permeability up to several 10 MHz. These ferrites can be used for filtering purposes in high frequency applications where a wide frequency band is required. In this paper, we study the magnetization processes taking place in these nano grained materials, in the frequency interval of 100 kHz to 5 MHz. Using a fluxmetric hysteresis graph, permeability, loss, and BH loops are measured at different temperatures, from -5 deg. C to 110 deg. C. Results are compared to the behavior of micrometric grain size ferrites, which are commonly used for power electronic and high frequency applications.

36 MATERIALS SCIENCE↗

Fabrication and Spark plasma sintering of nanostructured bismuth telluride (Bi{sub 2}Te{sub 3})

Thermoelectric (TE) devices can harvest residual low-grade waste heat energy. Bismuth telluride (Bi{sub 2}Te{sub 3}) and its alloys are mostly used TE materials in the bulk form for making TE modules. We report a simple, fast and very high yield synthetic process for the bulk Bi{sub 2}Te{sub 3} nanopowders with hexagonal plate like morphology. Spark plasma sintering (SPS) process has been optimized in order to preserve nanostructure while achieving a high compaction density of the pellets. Electron microscopy analysis was used to determine the effect of SPS parameters during compaction on the grain growth. Optimal conditions for the fabricated nanopowder was determined as 673 K, 70 MPa pressure with no holding time, which resulted in average lateral grain size in the range of 165-190 nm for a compact density of 98%. About 50% reduction of thermal conductivity was observed as compared to its bulk counterparts, revealing the feasibility of suggested route in the preservation of nanostructure and enhanced phonon scattering.

36 MATERIALS SCIENCE↗

Temperature modeling for analysis and design of the sintering furnance in HTR fuel type of ball

One of the factors that determine the safety of the operation of the sintering furnace fuel HTR ball is the temperature distribution in the ceramic tube furnace. The temperature distribution must be determined at design stage. The tube has a temperature of 1600 °C at one end and about 40 °C at the other end. The outside of the tube was cooled by air through natural convection. The tube is a furnace ceramic tube which its geometry are 0.08, 0.09 and 0.5 m correspondingly for the inner tube diameter, outer tube diameter and tube length. The temperature distribution of the tube is determined by the natural convection coefficient (NCF), which is difficult to be calculated manually. The determination of NCF includes the Grasshoff, Prandtl, and Nusselt numbers which is a function of the temperature difference between the surrounding air with the ceramic tube. If the temperature vary along the tube, the complexity of the calculations increases. Thus the proposed modeling was performed to determine the temperature distribution along the tube and heat transfer coefficient using a self-developed software which permit the design process easier.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗