Search NASA⌕ Search

SEARCH · Search NASA

Results for “Struts”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

A mobile transporter concept for EVA assembly of future spacecraft

This paper details the ground test program for the NASA Langley Research Center Mobile Transporter concept. The Mobile Transporter would assist EVA astronauts in the assembly of the Space Station Freedom. 1-g and simulated O-g (neutral buoyancy) tests were conducted to evaluate the use of the Mobile Transporter. A three-bay (44 struts) orthogonal tetrahedral truss configuration with a 15-foot-square cross section was repeatedly assembled by a single pair of pressure suited test subjects working from the Mobile Transporter astronaut positioning devices. The average unit assembly time was 28 seconds/strut. The results of these tests indicate that the use of a Mobile Transporter for EVA assembly of Space Station size structure is viable and practical. Additionally, the Mobile Transporter could be used to construct other spacecraft such as the submillimeter astronomical laboratory, space crane, and interplanetary (i.e., Mars and lunar) spacecraft.

Watson, Judith J.↗

An articulated-truss space crane concept

An articulated-truss space-crane concept is described, and four articulating-joint (AJ) concepts are evaluated. The space-crane concept uses the same truss structure hardware as Space Station Freedom. The joint concepts are compared according to their actuator stroke ratio, actuator authority, and part count. One AJ concept is selected as a candidate space-crane joint because of its better performance and lower part count. The space-crane reach envelope is determined as a function of the number of AJs and the number of fixed-length booms. A space crane with three booms, three AJs, and one rotary joint provides an adequate reach envelope for an expected work area. The space-crane tip velocity, because of an allowable truss strut compressive load, is limited to approximately 1.0 in./sec for a 300,000-lbm payload. The displacement response is also shown for an emergency stop scenario as a function of the payload mass. The space-crane tip deflection is on the order of 12 in. for a 300,000-lbm payload.

Sutter, Thomas R.↗

Flow establishment in a generic scramjet combustor

The establishment of a quasi-steady flow in a generic scramjet combustor is studied for the case of a time varying inflow to the combustor. Such transient flow is characteristic of the reflected-shock tunnel and expansion-tube test facilities. Several numerical simulations of hypervelocity flow through a straight-duct combustor with either a side-wall-step fuel injector or a centrally-located strut injector are presented. Comparisons are made between impulsively started but otherwise constant flow conditions (typical of the expansion-tube or tailored operation of the reflected-shock tunnel) and the relaxing flow produced by the 'undertailored' operation of the reflected-shock tunnel. Generally the inviscid flow features, such as the shock pattern and pressure distribution, were unaffected by the time varying inlet conditions and approached steady state in approximately the times indicated by experimental correlations. However, viscous features, such as heat transfer and skin friction, were altered by the relaxing inlet flow conditions.

Jacobs, P. A.↗

Flow establishment in a generic scramjet combustor

The establishment of a quasi-steady flow in a generic scramjet combustor was studied for the case of a time varying inflow to the combustor. Such transient flow is characteristic of the reflected shock tunnel and expansion tube test facilities. Several numerical simulations of hypervelocity flow through a straight duct combustor with either a side wall step fuel injector or a centrally located strut injector are presented. Comparisons were made between impulsively started but otherwise constant flow conditions (typical of the expansion tube or tailored operations of the reflected shock tunnel) and the relaxing flow produced by the 'undertailored' operations of the reflected shock tunnel. Generally the inviscid flow features, such as the shock pattern and pressure distribution, were unaffected by the time varying inlet conditions and approached steady state in approx. the times indicated by experimental correlations. However, viscous features, such as heat transfer and skin friction, were altered by the relaxing inlet flow conditions.

Jacobs, P. A.↗

Comparative morphology of configurations with reduced part count derived from the octahedral-tetrahedral truss

Morphology (the study of structure and form) of the octahedral-tetrahedral (octet) truss is described. Both the geometry and symmetry of the octet truss are considered. Morphological techniques based on symmetry operations are presented which enable the derivation of reduced-part-count truss configurations from the octet truss by removing struts and nodes. These techniques are unique because their Morphological origination and they allow for the systematic generation and analysis of a large variety of structures. Methods for easily determining the part count and redundancy of infinite truss configurations are presented. Nine examples of truss configurations obtained by applying the derivation techniques are considered. These configurations are structurally stable while at the same time exhibiting significant reductions in part count. Some practical and analytical considerations, such as structural performance, regarding the example reduced-part-count truss geometries are briefly discussed.

Lalvani, Haresh↗

Integrated Cryogenic Experiment (ICE) microsphere investigation

The main objective is to determine the performance of microsphere insulation in a 0-g environment and compare its performance to reference insulations such as multilayer insulation. The Lockheed Helium Extended-Life Dewar (HELD) is used to provide superfluid-helium cold sink for the experiment. The use of HELD allows the low-g dynamic properties of Passive Orbital Disconnect Struts (PODS) to be characterized and provides a flight demonstration of the PODS system. The thermal performance of microspheres in 1 and 0 g was predicted, a flight experiment was designed to determine microsphere thermal performance, and the interface was also designed between the experimental package and the shuttle through HELD and the Hitchhiker-M carrier. A single test cell was designed and fabricated. The cell was filled with uncoated glass microspheres and tested with a liquid-nitrogen cold sink. The data were found to agree with predictions of microsphere performance in 1 g.

Spradley, I.↗

Analytical and experimental investigations of the oblique detonation wave engine concept

Wave combustors, which include the oblique detonation wave engine (ODWE), are attractive propulsion concepts for hypersonic flight. These engines utilize oblique shock or detonation waves to rapidly mix, ignite, and combust the air-fuel mixture in thin zones in the combustion chamber. Benefits of these combustion systems include shorter and lighter engines which require less cooling and can provide thrust at higher Mach numbers than conventional scramjets. The wave combustor's ability to operate at lower combustor inlet pressures may allow the vehicle to operate at lower dynamic pressures which could lessen the heating loads on the airframe. The research program at NASA-Ames includes analytical studies of the ODWE combustor using Computational Fluid Dynamics (CFD) codes which fully couple finite rate chemistry with fluid dynamics. In addition, experimental proof-of-concept studies are being performed in an arc heated hypersonic wind tunnel. Several fuel injection design were studied analytically and experimentally. In-stream strut fuel injectors were chosen to provide good mixing with minimal stagnation pressure losses. Measurements of flow field properties behind the oblique wave are compared to analytical predictions.

Menees, Gene P.↗

Thermal performance of a liquid hydrogen tank multilayer insulation system at warm boundary temperatures of 630, 530, and 152 R

The results are presented of a study conducted to obtain experimental heat transfer data on a liquid hydrogen tank insulated with 34 layers of MLI (multilayer insulation) for warm side boundary temperatures of 630, 530, and 150 R. The MLI system consisted of two blankets, each blanket made up of alternate layers of double silk net (16 layers) and double aluminized Mylar radiation shields (15 layers) contained between two cover sheets of Dacron scrim reinforced Mylar. The insulation system was designed for and installed on a 87.6 in diameter liquid hydrogen tank. Nominal layer density of the insulation blankets is 45 layers/in. The insulation system contained penetrations for structural support, plumbing, and electrical wiring that would be representative of a cryogenic spacecraft. The total steady state heat transfer rates into the test tank for shroud temperatures of 630, 530, 152 R were 164.4, 95.8, and 15.9 BTU/hr respectively. The noninsulation heat leaks into the tank (12 fiberglass support struts, tank plumbing, and instrumentation lines) represent between 13 to 17 pct. of the total heat input. The heat input values would translate to liquid H2 losses of 2.3, 1.3, and 0.2 pct/day, with the tank held at atmospheric pressure.

Stochl, Robert J.↗

Systems integration and demonstration of advanced reusable structure for ALS

The objective was to investigate the potential of advanced material to achieve life cycle cost (LCC) benefits for reusable structure on the advanced launch system. Three structural elements were investigated - all components of an Advanced Launch System reusable propulsion/avionics module. Leading aeroshell configurations included sandwich structure using titanium, graphite/polyimide (Gr/PI), or high-temperature aluminum (HTA) face sheets. Thrust structure truss concepts used titanium, graphite/epoxy, or silicon carbide/aluminum struts. Leading aft bulkhead concepts employed graphite epoxy and aluminum. The technical effort focused on the aeroshell because the greatest benefits were expected there. Thermal analyses show the structural temperature profiles during operation. Finite element analyses show stresses during splash-down. Weight statements and manufacturing cost estimates were prepared for calculation of LCC for each design. The Gr/PI aeroshell showed the lowest potential LCC, but the HTA aeroshell was judged to be lower risk. A technology development plan was prepared to validate the applicable structural technology.

Gibbins, Martin N.↗

Development of an active truss element for control of precision structures

An active structural element for use in precision control of large space structures is described. The active member is intended to replace a passive strut in a truss-like structure. It incorporates an eddy current displacement sensor and an actuator that is either piezoelectric (PZT) or electrostrictive (PMN). The design of the device is summarized. Performance of separate PZT and PMN actuators is compared for several properties relevant to submicrometer control of precision structures.

Anderson, Eric H.↗

Scramjet mixing establishment times for a pulse facility

A numerical simulation of the temporally developing flow through a generic scramjet combustor duct is presented for stagnation conditions typical of flight at Mach 13 as produced by a shock tunnel pulse facility. The particular focus is to examine the start up transients and to determine the time required for certain flow parameters to become established. The calculations were made with a Navier-Stokes solver SPARK with temporally relaxing inflow conditions derived from operation of the T4 shock tunnel at the University of Queensland in Australia. Calculations at nominal steady inflow conditions were made for comparison. The generic combustor geometry includes the injection of hydrogen fuel from the base of a centrally located strut. In both cases, the flow was assumed laminar and fuel combustion was not included. The establishment process is presented for viscous parameters in the boundary layer and for parameters related to the fuel mixing.

Rogers, R. Clayton↗

Adaptive truss structure

This paper discusses the research in adaptive structures conducted at NASA Langley Research Center. The objective in the research program on adaptive truss structures is to develop an integrated approach for the design, test, and evaluation of adaptive trusses. An adaptive structure must include sensors for measuring some of the states of the mechanism, a controller that processes the sensor information and generates command signals, and a device that will cause the struts in the mechanism to change length. Based on the results of the research program, it is concluded that alternative designs for future space applications are offered, and adaptive truss has been demonstrated to be effective for vibration suppression.

Horner, C. G.↗

Design aspects of long range supersonic LFC airplanes with highly swept wings

Studies on supersonic long-range LFC (laminar flow control) aircraft were performed with the aim of maximizing L/D and alleviating sonic boom during supersonic cruise. It is found that configurations with highly swept LFC wings of very high structural aspect ratio, with the sweep increasing toward the wing root and braced externally by wide chord laminarized struts, appear especially promising. In the supersonic cruise design condition the wing upper surface isobars are swept such that the flow in the direction normal to them is transonic with embedded supersonic zones and practically shock-free over most of the span, with M-perpendicular equal to the two-dimensional design values of advanced SC LFC airfoils, e.g., of the X-787 or X-6 type.

Pfenninger, W.↗

Active suspensions for vibration isolation

The concept of mechanical impedances is used to analyze constraints on a single-link vibration isolation suspension. In particular, an assessment is made of the effects of the limited feedback bandwidth on the achievable suspension impedance and corresponding limits of attenuation of the transmitted force using Bode integral constraints and Blackman's formula. The performance of a piezoelectric strut is evaluated as an example.

Lurie, B. J.↗

Thermal performance of a liquid hydrogen tank multilayer insulation system at warm boundary temperatures of 630, 530, and 152 R

The results are presented of a study conducted to obtain experimental heat transfer data on a liquid hydrogen tank insulated with 34 layers of MLI (multilayer insulation) for warm side boundary temperatures of 630, 530, and 150 R. The MLI system consisted of two blankets, each blanket made up of alternate layers of double silk net (16 layers) and double aluminized Mylar radiation shields (15 layers) contained between two cover sheets of Dacron scrim reinforced Mylar. The insulation system was designed for and installed on an 87.6 in. diameter liquid hydrogen tank. Nominal layer density of the insulation blankets is 45 layers/in. The insulation system contained penetrations for structural support, plumbing, and electrical wiring that would be representative of a cryogenic spacecraft. The total steady state heat transfer rates into the test tank for shroud temperatures of 630, 530, 152 R were 164.4, 95.8, and 15.9 BTU/hr, respectively. The noninsulation heat leaks into the tank (12 fiberglass support struts, tank plumbing, and instrumentation lines) represent between 13 to 17 pct. of the total heat input. The heat input values would translate to liquid H2 losses of 2.3, 1.3, and 0.2 pct/day, with the tank held at atmospheric pressure.

Stochl, Robert J.↗

Supersonic combustion with transverse, circular wall jets

A series of experiments are reported using inclined circular wall jets in rectangular scramjet combustion chambers configured as constant area ducts. A free piston shock tunnel was used to create inlet flow Mach numbers between 4.2 and 5.5, at enthalpies corresponding to flight speeds of between 3.5 and 5.3 km/s. Measurements of duct static pressure levels indicated that significant mixing and combustion was achieved. Using hydrogen as a fuel, it was found that multipoint injection from two sides of the duct gave a larger, and more rapid, pressure rise. In hypersonic flow, it was found that combustion only occurred for the same duct dimensions and operating conditions that supported combustion with central injection from a two-dimensional strut. Wall injection from discrete orifice circular jets was found to be more effective than two-dimensional wall injection across the whole width of the duct.

Morgan, R. G.↗

Soft-Capture Mechanism For Collet Joint

Soft-capture mechanism part of latching-and-rigidifying mechanism joining strut rigidly to node on truss. Latching-and-rigidifying mechanism of spreading-collet type, in which collet inserted into base that mates with collet to assure proper alignment, then collet spread to rigidify joint, fixing alignment. Designed to be operable by heavily gloved hand or by robot.

Huff, John E., Jr.↗

Robot Would Assemble Collet/Flexible-Drive Truss Joint

Proposed truss joint designed for assembly by robot. Requires only simple motions of end effector of robot, tolerates relatively large initial misalignment of strut, and assembled with little feedback. Principal features of joint: expanding collet latches it to node ball and collet expanded by flexible drive shaft operated by robot. Developed for Space Station, also used for robotic construction in hazardous or undersea locations.

Evenson, Erik E.↗