Search NASA⌕ Search

SEARCH · Search NASA

Results for “THICKNESS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

Effects of Co layer thickness and annealing temperature on the magnetic properties of inverted [Pt/Co] multilayers

The effects of Co layer thickness and annealing temperature on the perpendicular magnetic anisotropy (PMA) properties of inverted [Pt (0.2 nm)/Co (t{sub Co})]{sub 6} multilayers (where t{sub Co} indicates the thickness of the Co layer) have been investigated. The cross-sectional microstructure, as observed from the high-resolution transmission electron microscope images, shows a clear layered structure with atomically flat interfaces both in the as-deposited state as well as after annealing, indicating the interface effects for PMA. The effective PMA energy density (K{sub eff}) increases significantly with an increase in t{sub Co} from 0.2 to 0.28 nm and then becomes almost saturated with further increases in t{sub Co}, followed by a slight reduction at the highest Co thickness, t{sub Co} = 0.6 nm. In order to explain the t{sub Co} dependence on K{sub eff}, the intrinsic PMA energy density (K{sub i}) is calculated by additionally measuring a similar set of results for the saturation magnetization. The K{sub i} value increases nearly linearly with the increase in t{sub Co} from 0.2 to 0.5 nm, followed by saturation at a higher t{sub Co} value of 0.6 nm. Owing to a close relationship between K{sub i} and the quality of the interfaces, these results indicate a similar t{sub Co} dependence on the quality of the interfaces. This is further supported from the magnetic measurements of the samples annealed at the highest temperature of 500 °C, where a second phase is formed, which show a similar t{sub Co} dependence on the amount of the second phase. The K{sub i} value is nearly independent of the annealing temperature at t{sub Co} ≤ 0.4 nm, above which a substantial reduction is observed, when the annealing temperature exceeds 500 °C.

36 MATERIALS SCIENCE↗

Effect of thickness and Ti interlayers on stresses and texture transformations in thin Ag films during thermal cycling

The driving forces for the (111) to (100) texture transformation often observed during annealing of thin face-centered cubic metal films were investigated. Thin passivated silver films were produced with and without Ti adhesion layers. Stresses were measured in situ during heating to induce the texture transformation, and the texture was characterized using x-ray diffraction. Sufficiently thin films did not transform and sufficiently thick films transformed fully. Intermediate thickness films transformed to an extent dependent on thickness, leading to stable mixed textures. In the prevailing thermodynamic model, texture transformation is attributed to minimization of strain and interface energies. However, calculations using the measured stresses, known elastic constants, and estimated interface energies in this model reveal that the stresses are not sufficient to cause the texture transformation and, furthermore, that variations in interface energy cannot lead to the observed behavior. The results suggest that neither the interface energy nor the stress plays decisive roles in the texture transformation.

36 MATERIALS SCIENCE↗

A reliable control system for measurement on film thickness in copper chemical mechanical planarization system

In recent years, a variety of film thickness measurement techniques for copper chemical mechanical planarization (CMP) are subsequently proposed. In this paper, the eddy-current technique is used. In the control system of the CMP tool developed in the State Key Laboratory of Tribology, there are in situ module and off-line module for measurement subsystem. The in situ module can get the thickness of copper film on wafer surface in real time, and accurately judge when the CMP process should stop. This is called end-point detection. The off-line module is used for multi-points measurement after CMP process, in order to know the thickness of remained copper film. The whole control system is structured with two levels, and the physical connection between the upper and the lower is achieved by the industrial Ethernet. The process flow includes calibration and measurement, and there are different algorithms for two modules. In the process of software development, C++ is chosen as the programming language, in combination with Qt OpenSource to design two modules’ GUI and OPC technology to implement the communication between the two levels. In addition, the drawing function is developed relying on Matlab, enriching the software functions of the off-line module. The result shows that the control system is running stably after repeated tests and practical operations for a long time.

42 ENGINEERING↗

Application of MMC model on simulation of shearing process of thick hot-rolled high strength steel plate

Shear operation is widely used as the first step in sheet metal forming to cut the sheet or plate into the required size. The shear of thick hot-rolled High Strength Steel (HSS) requires large shearing force and the sheared edge quality is relatively poor because of the large thickness and high strength compared with the traditional low carbon steel. Bad sheared edge quality will easily lead to edge cracking during the post-forming process. This study investigates the shearing process of thick hot-rolled HSS plate metal, which is generally exploited as the beam of heavy trucks. The Modified Mohr-Coulomb fracture criterion (MMC) is employed in numerical simulation to calculate the initiation and propagation of cracks during the process evolution. Tensile specimens are designed to obtain various stress states in tension. Equivalent fracture strains are measured with Digital Image Correlation (DIC) equipment to constitute the fracture locus. Simulation of the tension test is carried out to check the fracture model. Then the MMC model is applied to the simulation of the shearing process, and the simulation results show that the MMC model predicts the ductile fracture successfully.

36 MATERIALS SCIENCE↗

Influence of the SiO{sub 2} interlayer thickness on the density and polarity of charges in Si/SiO{sub 2}/Al{sub 2}O{sub 3} stacks as studied by optical second-harmonic generation

By accurately tuning the SiO{sub 2} interlayer thickness the density and polarity of charges in Si/SiO{sub 2}/Al{sub 2}O{sub 3} stacks can be controlled. We report on the number density, polarity, and physical location of charges present in the stacks as studied by optical second-harmonic generation (SHG). Depending on the SiO{sub 2} interlayer thickness (1–150 nm) the effective charge density in the Si/SiO{sub 2}/Al{sub 2}O{sub 3} stacks ranges from 10{sup 13} to 10{sup 11} cm{sup −2} for both n- and p-type silicon. The polarity of the charges switches from negative to positive around a SiO{sub 2} interlayer thickness of 5–10 nm at which point the effective charge density in the stacks is negligible. This switch in polarity is apparent from spectroscopic, time-dependent, and azimuthal SHG measurements. The observed trends in charge density and polarity can be explained by tunneling of electrons into defect states at the SiO{sub 2}/Al{sub 2}O{sub 3} interface as well as the presence of fixed and bulk charges at the Si/SiO{sub 2} interface and in the SiO{sub 2}, respectively. This charge mechanism appears to hold generally for Si/SiO{sub 2}/Al{sub 2}O{sub 3} stacks as similar results were observed for SiO{sub 2} films prepared by various techniques.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Thickness and ordering temperature of surface NiO/Ni systems

We estimate the thickness and ordering temperature of an antiferromagnetic and passivation surface oxide through exchange bias coupling. The surface NiO, which is generated through the exposure of a Ni/Cu(001) surface to oxygen, is taken as a model system on which to perform the estimation. Since no exchange bias is found in the surface NiO/Ni/Cu(001), we have built a sandwich structure of NiO/n ML Ni/10 ML Co/Cu(001) to measure the n dependence of exchange bias. With n ⩽ 2, a large exchange bias field is found above 300 K, which could be due to the direct contact between the oxides and the Co layer. With 3 ⩽ n ⩽ 6, a smaller exchange bias field is found with a blocking temperature of 190 K. This implies that the thickness of NiO is, at most, 3 ML. Discovering the thickness and ordering temperature of the surface NiO provides us to explore the potential applications by using surface NiO.

36 MATERIALS SCIENCE↗

A study on the evolution of dielectric function of ZnO thin films with decreasing film thickness

Dielectric function, band gap, and exciton binding energies of ultrathin ZnO films as a function of film thickness have been obtained with spectroscopic ellipsometry. As the film thickness decreases, both real (ε{sub 1}) and imaginary (ε{sub 2}) parts of the dielectric function decrease significantly, and ε{sub 2} shows a blue shift. The film thickness dependence of the dielectric function is shown related to the changes in the interband absorption, discrete-exciton absorption, and continuum-exciton absorption, which can be attributed to the quantum confinement effect on both the band gap and exciton binding energies.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

The effect of mix on capsule yields as a function of shell thickness and gas fill

An investigation of direct drive capsules with different shell thicknesses and gas fills was conducted to examine the amount of shock induced (Richtmyer-Meshkov) mix versus Rayleigh-Taylor mix from deceleration of the implosion. The RAGE (Eulerian) code with a turbulent mix model was used to model these capsules for neutron yields along with time-dependent mix amounts. The amount of Richtmyer-Meshkov induced mix from the shock breaking out of the shell is about 0.1 μg (0.15 μm of shell material), while the Rayleigh-Taylor mix is of order 1 μg and determines the mixed simulation yield. The simulations were able to calculate a yield over mix (YOM) ratio (experiment/mix simulation) between 0.5 and 1.0 for capsules with shell thicknesses ranging from 7.5 to 20 μm and with gas fills between 3.8 and 20 atm of D{sub 2} or DT. The simulated burn averaged T{sub ion} values typically lie with 0.5 keV of the data, which is within the measurement error. For capsules with shell thicknesses >25 μm, the YOM values drop to 0.10 ± 0.05, suggesting that some unmodeled effect needs to be accounted for in the thickest capsules.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The influence of the AlN barrier thickness on the polarization Coulomb field scattering in AlN/GaN heterostructure field-effect transistors

The electron mobility scattering mechanisms in AlN/GaN heterostuctures with 3 nm and 6 nm AlN barrier thicknesses were investigated by temperature-dependent Hall measurements. The effect of interface roughness (IFR) scattering on the electron mobility was found to be enhanced by increasing AlN barrier thickness. Moreover, using the measured capacitance-voltage and current-voltage characteristics of the fabricated heterostructure field-effect transistors (HFETs) with different Schottky areas on the two heterostuctures, the variations of electron mobility with different gate biases were investigated. Due to enhanced IFR scattering, the influence of polarization Coulomb field (PCF) scattering on electron mobility was found to decrease with increasing AlN barrier layer thickness. However, the PCF scattering remained an important scattering mechanism in the AlN/GaN HFETs.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Evaluation of thickness and strain of thin planar layers of InAs on GaAs(001) using spectroscopic ellipsometry

We develop a technique for accurately measuring thickness of planar InAs films grown on (001) GaAs by spectroscopic ellipsometry, using bulk optical constants. We observe that the critical point structure for the E{sub 1} and E{sub 1} + Δ{sub 1} transitions extracted from the measured dielectric properties varies with strain in the layer. Transmission electron microscopy confirms the extracted thickness and measures the residual strain based on the dislocation spacing in the film. At small thickness, the E{sub 1} critical point is seen to markedly deviate from the dependence predicted by deformation potential theory and appears to be consistent with additional quantum confinement effects.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Realistic reflectance spectrum of thin films covering a transparent optically thick substrate

A spectrophotometric strategy is presented and discussed for calculating realistically the reflectance spectrum of an absorbing film deposited over a thick transparent or semi-transparent substrate. The developed route exploits simple mathematics, has wide range of applicability (high-to-weak absorption regions and thick-to-ultrathin films), rules out numerical and curve-fitting procedures as well as model-functions, inherently accounts for the non-measurable contribution of the film-substrate interface as well as substrate backside, and describes the film reflectance spectrum as determined by the experimental situation (deposition approach and parameters). The reliability of the method is tested on films of a well-known material (indium tin oxide) by deliberately changing film thickness and structural quality through doping. Results are found consistent with usual information yielded by reflectance, its inherent relationship with scattering processes and contributions to the measured total reflectance.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Tuning the thickness of electrochemically grafted layers in large area molecular junctions

We have investigated the thickness, the surface roughness, and the transport properties of oligo(1-(2-bisthienyl)benzene) (BTB) thin films grafted on evaporated Au electrodes, thanks to a diazonium-based electro-reduction process. The thickness of the organic film is tuned by varying the number of electrochemical cycles during the growth process. Atomic force microscopy measurements reveal the evolution of the thickness in the range of 2–27 nm. Its variation displays a linear dependence with the number of cycles followed by a saturation attributed to the insulating behavior of the organic films. Both ultrathin (2 nm) and thin (12 and 27 nm) large area BTB-based junctions have then been fabricated using standard CMOS processes and finally electrically characterized. The electronic responses are fully consistent with a tunneling barrier in case of ultrathin BTB film whereas a pronounced rectifying behavior is reported for thicker molecular films.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Engineering 180° ferroelectric domains in epitaxial PbTiO{sub 3} thin films by varying the thickness of the underlying (La,Sr)MnO{sub 3} layer

Epitaxial ferroelectric thin films of PbTiO{sub 3} (PTO) grown on top of nominally La{sub 0.7}Sr{sub 0.3}MnO{sub 3} (LSMO) submicron hillocks on Nb-doped SrTiO{sub 3} (100) substrate were investigated by means of scanning transmission electron microscopy. 180° ferroelectric domains were observed in the c-axis oriented PTO films. The formation and configuration of ferroelectric domains and domain walls were found to exhibit strong correlation with the thickness of the underlying LSMO hillocks. The domain walls start at the locations of the hillocks where the LSMO layer has a thickness of about 3 nm. Our results demonstrate that controlling the thickness variation (shape) of the LSMO hillocks can manipulate the position and density of the ferroelectric domain walls, which are considered to be the active elements for future nanoelectronics.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Thickness controlled sol-gel silica films for plasmonic bio-sensing devices

Plasmonics has recently received considerable interest due to its potentiality in many fields as well as in nanobio-technology applications. In this regard, various strategies are required for modifying the surfaces of plasmonic nanostructures and to control their optical properties in view of interesting application such as bio-sensing, We report a simple method for depositing silica layers of controlled thickness on planar plasmonic structures. Tetraethoxysilane (TEOS) was used as silica precursor. The control of the silica layer thickness was obtained by optimizing the sol-gel method and dip-coating technique, in particular by properly tuning different parameters such as pH, solvent concentration, and withdrawal speed. The resulting films were characterized via atomic force microscopy (AFM), Fourier-transform (FT) spectroscopy, and spectroscopic ellipsometry (SE). Furthermore, by performing the analysis of surface plasmon resonances before and after the coating of the nanostructures, it was observed that the position of the resonance structures could be properly shifted by finely controlling the silica layer thickness. The effect of silica coating was assessed also in view of sensing applications, due to important advantages, such as surface protection of the plasmonic structure.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

High-power low-droop violet semipolar (303{sup ¯}1{sup ¯}) InGaN/GaN light-emitting diodes with thick active layer design

Devices grown on nonpolar and semipolar planes of GaN offer key performance advantages over devices grown on the conventional c-plane, including reduced polarization fields. This allows for a wider design space on semipolar planes for light emitting diodes (LEDs) to address the problem of efficiency droop at high current densities. LED structures with very thick (10–100 nm) InGaN single-quantum-well/double heterostructure active regions were grown using conventional metal organic chemical vapor deposition on semipolar (303{sup ¯}1{sup ¯}) free-standing GaN substrates and processed and packaged using conventional techniques. Simulated band diagrams showed reduced polarization fields on the (303{sup ¯}1{sup ¯}) plane. The calculated critical thickness for misfit dislocation formation is higher on the (303{sup ¯}1{sup ¯}) plane than on other semipolar planes, such as (202{sup ¯}1{sup ¯}), allowing for thicker active regions than our previous work to further reduce droop. The higher critical thickness was confirmed with defect characterization via cathodoluminescence. A trend is demonstrated in lower efficiency droop for devices with thicker active regions. Thermal droop characteristics of these devices are also presented. These observed results were utilized to demonstrate over 1 W of output power at a current density of 1 kA/cm{sup 2} from a single 0.1 mm{sup 2} LED device.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Weakly nonlinear Rayleigh-Taylor instability of a finite-thickness fluid layer

A weakly nonlinear (WN) model has been developed for the Rayleigh-Taylor instability of a finite-thickness incompressible fluid layer (slab). We derive the coupling evolution equations for perturbations on the (upper) “linearly stable” and (lower) “linearly unstable” interfaces of the slab. Expressions of temporal evolutions of the amplitudes of the perturbation first three harmonics on the upper and lower interfaces are obtained. The classical feedthrough (interface coupling) solution obtained by Taylor [Proc. R. Soc. London A 201, 192 (1950)] is readily recovered by the first-order results. Our third-order model can depict the WN perturbation growth and the saturation of linear (exponential) growth of the perturbation fundamental mode on both interfaces. The dependence of the WN perturbation growth and the slab distortion on the normalized layer thickness (kd) is analytically investigated via the third-order solutions. Comparison is made with Jacobs-Catton's formula [J. W. Jacobs and I. Catton, J. Fluid Mech. 187, 329 (1988)] of the position of the “linearly unstable” interface. Using a reduced formula, the saturation amplitude of linear growth of the perturbation fundamental mode is studied. It is found that the finite-thickness effects play a dominant role in the WN evolution of the slab, especially when kd < 1. Thus, it should be included in applications where the interface coupling effects are important, such as inertial confinement fusion implosions and supernova explosions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Cathode fall thickness of abnormal glow discharges between parallel-plane electrodes in different radii at low pressure

In order to investigate the influence of electrode radius on the characteristics of cathode fall thickness, experiments of low-pressure (20 Pa ≤ p ≤ 30 Pa) abnormal glow discharge were carried out between parallel-plane electrodes in different radii keeping gap distance unchanged. Axial distributions of light intensity were obtained from the discharge images captured using a Charge Coupled Device camera. The assumption that the position of the negative glow peak coincides with the edge of cathode fall layer was verified based on a two-dimensional model, and the cathode fall thicknesses, d{sub c}, were calculated from the axial distributions of light intensity. It was observed that the position of peak emission shifts closer to the cathode as current or pressure grows. The dependence of cathode fall thickness on the gas pressure and normalized current J/p{sup 2} was presented, and it was found that for discharges between electrodes in large radius the curves of pd{sub c} against J/p{sup 2} were superimposed on each other, however, this phenomenon will not hold for discharges between the smaller electrodes. The reason for this phenomenon is that the transverse diffusions of charged particles are not the same in two gaps between electrodes with different radii.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Correlation between Pd metal thickness and thermally stable perpendicular magnetic anisotropy features in [Co/Pd]{sub n} multilayers at annealing temperatures up to 500 °C

We examine highly stable perpendicular magnetic anisotropy (PMA) features of [Co/Pd]{sub 10} multilayers (MLs) versus Pd thickness at various ex-situ annealing temperatures. Thermally stable PMA characteristics were observed up to 500 °C, confirming the suitability of these systems for industrial applications at this temperature. Experimental observations suggest that the choice of equivalent Co and Pd layer thicknesses in a ML configuration ensures thermally stable PMA features, even at higher annealing temperatures. X-ray diffraction patterns and cross-sectional transmission electron microscopy images were obtained to determine thickness, post-annealing PMA behavior, and to explore the structural features that govern these findings.

36 MATERIALS SCIENCE↗