Search NASA⌕ Search

SEARCH · Search NASA

Results for “WINGS - EXPERIMENTAL TESTS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43
All sourcesNASA NTRSDOE OSTI
NASA NTRS2001

Subsonic Reynolds Number Effects on a Diamond Wing Configuration

An advanced diamond-wing configuration was tested at low speeds in the National Transonic Facility (NTF) in air at chord Reynolds numbers from 4.4 million (typical wind-tunnel conditions) to 24 million (nominal flight value). Extensive variations on high-lift rigging were explored as part of a broad multinational program. The analysis for this study is focused on the cruise and landing settings of the wing high-lift systems. Three flow domains were identified from the data and provide a context for the ensuing data analysis. Reynolds number effects were examined in incremental form based upon attached-flow theory. A similar approach showed very little effect of low-speed compressibility.

Luckring, J. M.↗
NASA NTRS1947

Flight-Test Evaluation of the Longitudinal Stability and Control Characteristics of 0.5-Scale Models of the Fairchild Lark Pilotless-Aircraft Configuration: Standard Configuration with Wing Flaps Deflected 60 Degrees and Model having Tail in Line with Wings, TED No. NACA 2387

Flight tests were conducted at the Flight Test Station of the Pilotless Aircraft Research Division at Wallop Island, Va., to determine the longitudinal control and stability characteristics of 0.5-scale models of the Fairchild Lark pilotless aircraft with the tail in line with the wings a d with the horizontal wing flaps deflected 60 deg. The data were obtained by the use of a telemeter and by radar tracking.

Stone, David G.↗
NASA NTRS1939

The effects of partial-span slotted flaps on the aerodynamic characteristics of a rectangular and a tapered N.A.C.A. 23012 wing

An investigation was made in the N.A.C.A. 7- by 10-foot wind tunnel to determine the aerodynamic characteristics of tapered and rectangular wings with partial-span slotted flaps. Two N.A.C.A. 23012 airfoils equipped with center-section and tip-section flaps were tested. The results showed that the changes in lift and drag due to changes in flap span for both rectangular and tapered wings having partial-span slotted flaps were similar to those for corresponding wings having partial-span split or plain flaps. For the two wings tested, higher values of maximum lift were obtained with center-section slotted flaps than with tip-section slotted flaps of the same size. The highest values of lift-drag ratio at maximum lift for the rectangular wing were obtained with center-section flaps and, for the tapered wing, with tip-section flaps. Center-section flaps on the tapered wing gave higher values of drag at maximum lift than tip-section flaps; no great difference in drag at maximum lift was apparent for either center-section or tip-section slotted flaps on the rectangular wing.

House, Rufus O↗
NASA NTRS1991

Algorithm and code development for unsteady three-dimensional Navier-Stokes equations

A streamwise upwind algorithm for solving the unsteady 3-D Navier-Stokes equations was extended to handle the moving grid system. It is noted that the finite volume concept is essential to extend the algorithm. The resulting algorithm is conservative for any motion of the coordinate system. Two extensions to an implicit method were considered and the implicit extension that makes the algorithm computationally efficient is implemented into Ames's aeroelasticity code, ENSAERO. The new flow solver has been validated through the solution of test problems. Test cases include three-dimensional problems with fixed and moving grids. The first test case shown is an unsteady viscous flow over an F-5 wing, while the second test considers the motion of the leading edge vortex as well as the motion of the shock wave for a clipped delta wing. The resulting algorithm has been implemented into ENSAERO. The upwind version leads to higher accuracy in both steady and unsteady computations than the previously used central-difference method does, while the increase in the computational time is small.

Obayashi, Shigeru↗
DOE OSTI2022

A multipurpose lifting-line flow solver for arbitrary wind energy concepts

Abstract. In this work, we extend the AeroDyn module of OpenFAST to support arbitrary collections of wings, rotors, and towers. The new standalone AeroDyn driver supports arbitrary motions of the lifting surfaces and complex turbulent inflows. Aerodynamics and inflow are assembled into one module that can be readily coupled with an elastic solver. We describe the features and updates necessary for the implementation of the new AeroDyn driver. We present different case studies of the driver to illustrate its application to concepts such as multirotors, kites, or vertical-axis wind turbines. We perform verification and validation of some of the new features using the following test cases: elliptical wings, horizontal-axis wind turbines, and 2D and 3D vertical-axis wind turbines. The wind turbine simulations are compared to existing tools and field measurements. We use this opportunity to describe some limitations of current models and to highlight areas that we think should be the focus of future research in wind turbine aerodynamics.

17 WIND ENERGY↗
NASA NTRS1976

Acceleration of fatigue tests for built-up titanium components

A study was made of the feasibility of a room-temperature scheme of accelerating fatigue tests for Mach 3 advanced supersonic transport aircraft. The test scheme used equivalent room-temperature cycles calculated for supersonic flight conditions. Verification tests were conducted using specimens representing titanium wing lower surface structure. Test-acceleration parameters were developed for the test with an auxiliary test set. Five specimens were tested with a flight-by-flight load and temperature spectrum to simulate typical Mach 3 operation. Two additional sets of five specimens were tested at room temperature to evaluate the test-acceleration scheme. The fatigue behavior of the specimens generally correlated well with the proposed correction method.

Watanabe, R. T.↗
NASA NTRS2010

Utilization of 3-D Imaging Flash Lidar Technology for Autonomous Safe Landing on Planetary Bodies

NASA considers Flash Lidar a critical technology for enabling autonomous safe landing of future large robotic and crewed vehicles on the surface of the Moon and Mars. Flash Lidar can generate 3-Dimensional images of the terrain to identify hazardous features such as craters, rocks, and steep slopes during the final stages of descent and landing. The onboard flight computer can use the 3-D map of terrain to guide the vehicle to a safe site. The capabilities of Flash Lidar technology were evaluated through a series of static tests using a calibrated target and through dynamic tests aboard a helicopter and a fixed wing aircraft. The aircraft flight tests were performed over Moon-like terrain in the California and Nevada deserts. This paper briefly describes the Flash Lidar static and aircraft flight test results. These test results are analyzed against the landing application requirements to identify the areas of technology improvement. The ongoing technology advancement activities are then explained and their goals are described.

Amzajerdian, Farzin↗
NASA NTRS2015

ER-2 High Altitude Solar Cell Calibration Flights

Evaluation of space photovoltaics using ground-based simulators requires primary standard cells which have been characterized in a space or near-space environment. Due to the high cost inherent in testing cells in space, most primary standards are tested on high altitude fixed wing aircraft or balloons. The ER-2 test platform is the latest system developed by the Glenn Research Center (GRC) for near-space photovoltaic characterization. This system offers several improvements over GRC's current Learjet platform including higher altitude, larger testing area, onboard spectrometers, and longer flight season. The ER-2 system was developed by GRC in cooperation with NASA's Armstrong Flight Research Center (AFRC) as well as partners at the Naval Research Laboratory and Air Force Research Laboratory. The system was designed and built between June and September of 2014, with the integration and first flights taking place at AFRC's Palmdale facility in October of 2014. Three flights were made testing cells from GRC as well as commercial industry partners. Cell performance data was successfully collected on all three flights as well as solar spectra. The data was processed using a Langley extrapolation method, and performance results showed a less than half a percent variation between flights, and less than a percent variation from GRC's current Learjet test platform.

ER-2↗
NASA NTRS1993

Aerodynamic control of NASP-type vehicles through vortex manipulation. Volume 3: Wing rock experiments

Free-to-roll tests were conducted in water and wind tunnels in an effort to investigate the mechanisms of wing rock on a NASP-type vehicle. The configuration tested consisted of a highly-slender forebody and a 78 deg swept delta wing. In the water tunnel test, extensive flow visualization was performed and roll angle histories were obtained. In the wind tunnel test, the roll angle, forces and moments, and limited forebody and wing surface pressures were measured during the wing rock motion. A limit cycle oscillation was observed for angles of attack between 22 deg and 30 deg. In general, the experiments confirmed that the main flow phenomena responsible for the wing-body-tail wing rock are the interactions between the forebody and the wing vortices. The variation of roll acceleration (determined from the second derivative of the roll angle time history) with roll angle clearly slowed the energy balance necessary to sustain the limit cycle oscillation. Different means of suppressing wing rock by controlling the forebody vortices using small blowing jets were also explored. Steady blowing was found to be capable of suppressing wing rock, but significant vortex asymmetrices are created, causing the model to stop at a non-zero roll angle. On the other hand, alternating pulsed blowing on the left and right sides of the fore body was demonstrated to be a potentially effective means of suppressing wing rock and eliminating large asymmetric moments at high angles of attack.

Suarez, Carlos J.↗
NASA NTRS2007

Aeroelastic Model Structure Computation for Envelope Expansion

Structure detection is a procedure for selecting a subset of candidate terms, from a full model description, that best describes the observed output. This is a necessary procedure to compute an efficient system description which may afford greater insight into the functionality of the system or a simpler controller design. Structure computation as a tool for black-box modelling may be of critical importance in the development of robust, parsimonious models for the flight-test community. Moreover, this approach may lead to efficient strategies for rapid envelope expansion which may save significant development time and costs. In this study, a least absolute shrinkage and selection operator (LASSO) technique is investigated for computing efficient model descriptions of nonlinear aeroelastic systems. The LASSO minimises the residual sum of squares by the addition of an l(sub 1) penalty term on the parameter vector of the traditional 2 minimisation problem. Its use for structure detection is a natural extension of this constrained minimisation approach to pseudolinear regression problems which produces some model parameters that are exactly zero and, therefore, yields a parsimonious system description. Applicability of this technique for model structure computation for the F/A-18 Active Aeroelastic Wing using flight test data is shown for several flight conditions (Mach numbers) by identifying a parsimonious system description with a high percent fit for cross-validated data.

Kukreja, Sunil L.↗
DOE OSTI2022

Modeling the use of mobile modular gas samplers in near-field detection

The Wireless Independent Noble Gas Sampler (WINGS) is a mobile, modular gas sampling system designed for use in low infrastructure environments. In the case of a suspected underground nuclear explosion (UNE), WINGS units could be deployed to detect noble gases emanating from the suspected explosion site or identify gases originating from another source entering the local area from offsite. In conclusion, this work uses the atmospheric transport modeling tool inline WRF-HYSPLIT to test the effectiveness of WINGS units around a suspected UNE site as a function of sampler density and distance from the emission point of gases from a UNE.

Air sampling↗
NASA NTRS2001

Use of 3000 Bragg Grating Strain Sensors Distributed on Four Eight-meter Optical Fibers During Static Load Tests of a Composite Structure

This paper describes the use of a fiber optic system to measure strain at thousands of locations along optical fibers where weakly reflecting Bragg gratings have been photoetched. The optical fibers were applied to an advanced composite transport wing along with conventional foil strain gages. A comparison of the fiber optic and foil gage systems used for this test will be presented including: a brief description of both strain data systems; a discussion of the process used for installation of the optical fiber; comparative data from the composite wing test; the processes used for the location and display of the high density fiber optic data. Calibration data demonstrating the potential accuracy of the fiber optic system will also be presented. The opportunities for industrial and commercial applications will be discussed. The fiber optic technique is shown to be a valuable augmentation to foil strain gages providing insight to structural behavior previously requiring reliance on modeling.

Childers, Brooks A.↗
NASA NTRS1980

Preliminary aerodynamic characteristics of several advanced VSTOL fighter/attack aircraft concepts

VSTOL attack aircraft to be developed in the mid- or late-1990's and research programs dealing with possible characteristics are discussed. Design studies of horizontal attitude takeoff and landing (HATOL) and vertical attitude takeoff and landing (VATOL) type aircraft were executed and wind tunnel models were built and tested. The configurations tested were a wing-canard HATOL concept with jet-diffuser ejectors as a vertical lift system and a variety of the same with nacelles which are closer together. Other proposals were a HATOL concept with wing-canard design and two vertical tails on twin afterbodies, and a VATOL concept which is tailless with an extended leading-edge wing to increase lift. Aerodynamic uncertainties were defined and wind tunnel tests were made. Special research concerning top-mounted air induction systems is also covered.

Nelms, W. P.↗
NASA NTRS2017

Recent Advancements in the Infrared Flow Visualization System for the NASA Ames Unitary Plan Wind Tunnels

The following details recent efforts undertaken at the NASA Ames Unitary Plan wind tunnels to design and deploy an advanced, production-level infrared (IR) flow visualization data system. Highly sensitive IR cameras, coupled with in-line image processing, have enabled the visualization of wind tunnel model surface flow features as they develop in real-time. Boundary layer transition, shock impingement, junction flow, vortex dynamics, and buffet are routinely observed in both transonic and supersonic flow regimes all without the need of dedicated ramps in test section total temperature. Successful measurements have been performed on wing-body sting mounted test articles, semi-span floor mounted aircraft models, and sting mounted launch vehicle configurations. The unique requirements of imaging in production wind tunnel testing has led to advancements in the deployment of advanced IR cameras in a harsh test environment, robust data acquisition storage and workflow, real-time image processing algorithms, and evaluation of optimal surface treatments. The addition of a multi-camera IR flow visualization data system to the Ames UPWT has demonstrated itself to be a valuable analyses tool in the study of new and old aircraft/launch vehicle aerodynamics and has provided new insight for the evaluation of computational techniques.

Infrared Thermography↗
NASA NTRS1995

Development of a quiet supersonic wind tunnel with a cryogenic adaptive nozzle

Low-disturbance or 'quiet' wind tunnels are now considered an essential part of meaningful boundary layer transition research. Advances in Supersonic Laminar Flow Control (SLFC) technology for swept wings depends on a better understanding of the receptivity of the transition phenomena to attachment-line contamination and cross-flows. This need has provided the impetus for building the Laminar Flow Supersonic Wind Tunnel (LFSWT) at NASA-Ames, as part of the NASA High Speed Research Program (HSRP). The LFSWT was designed to provide NASA with an unequaled capability for transition research at low supersonic Mach numbers (<2.5). The following are the objectives in support of the new Fluid Mechanic Laboratory (FML) quiet supersonic wind tunnel: (I) Develop a unique injector drive system using the existing FML indraft compressor; (2) Develop an FML instrumentation capability for quiet supersonic wind tunnel evaluation and transition studies at NASA-Ames; (3) Determine the State of the Art in quiet supersonic wind tunnel design; (4) Build and commission the LFSWT; (5) Make detailed flow quality measurements in the LFSWT; (6) Perform tests of swept wing models in the LFSWT in support of the NASA HSR program; and (7) Provide documentation of research progress.

Wolf, Stephen W. D.↗
NASA NTRS1981

Aerodynamic features of designed strake-wing configurations

Sixteen analytically and empirically designed strakes have been aerodynamically tested on a common wing-body to determine the longitudinal characteristics of the configurations. These strakes were selected, in general, due to their superior performance in a water-tunnel test. There they exhibited a good correlation between the hypothesized high value of angle of attack for strake vortex breakdown and the high value of leading-edge suction at the strake tip. The lift and pitch data were reasonably well predicted by an extended suction analogy method, and the lift agreement improved with increasing strake area. The strake-vortex-breakdown angle and configuration maximum lift generally increase with increasing strake area and, to some extent, strake tip leading-edge suction value. The best strake configurations all developed about the same maximum area efficiency value despite their differences in size.

Lamar, J. E.↗