Search NASA⌕ Search

SEARCH · Search NASA

Results for “catalyst loading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

Experimental results with fuel cell start-up and shut-down. Impact of type of carbon for cathode catalyst support

Separate testing protocols for fuel cell startups and shutdowns were developed to distinguish between their effects on reverse currents and CO 2 evolution. The internal currents and the local potentials were measured with different membrane-electrode assemblies (MEAs): we examined the influence of the type of carbon for cathode catalyst support as well as the mitigating effect of low anode Pt loading. In conclusion, significant differences were observed and the experiments also confirmed previous results that the evolved CO 2 accounts for less than 25% of the total exchanged charge.

30 DIRECT ENERGY CONVERSION↗

Hierarchical multi-time-scale predictive thermal management and fuel optimization for heavy-duty compression ignition engines

For heavy-duty diesel engines, NO X emissions reduction is strongly constrained by fuel efficiency. This paper presents a hierarchical model predictive controller (H-MPC) for coordinated control of tailpipe NO X emissions and fuel consumption. The H-MPC uses the separation of slow and fast dynamics that exist in the engine and its aftertreatment system. The controller is synthesized with an architecture in which a high-level MPC uses a longer prediction horizon compared to the low-level predictive controller which tracks the high-level controller command and manages the thermal dynamics of the aftertreatment system. Engine load preview enables the high-level controller to estimate the desired catalyst temperature ahead of time and addresses the selective catalytic reduction (SCR) slow thermal dynamics. Calculated by the high-level controller, the intake manifold pressure, and the start of injection (SOI) crank angle is used as reference trajectories in the low-level controller that regulates fast dynamical behaviors such as engine out NO X emissions. Hardware-in-the-loop (HIL) validation of this integrated H-MPC on a rapid prototype controller shows that when the SCR catalyst temperature is above light-off temperature (warmed-up condition), the engine operation is shifted to operate with the best fuel economy since the warmed-up SCR can efficiently reduce the engine-out NO X emissions. Results indicate that up to 0.8% benefit in cycle averaged BSFC along with a 13% reduction in tailpipe NO X compared to a stock engine calibration can be achieved with the coordinated engine and aftertreatment system through H-MPC.

Engineering↗

Multifunctional Catalysts for the Tandem Reactions of Oxygenates

Industrially-relevant catalytic reactions rarely consist of a simple sequence of elementary steps. Moreover, kinetic coupling of multiple reactions on a catalyst surface is highly desired for process intensification and improved energy efficiency for large scale chemical transformations. The shifting landscape of hydrocarbon chemical feedstocks in the US also motivates research on the selective conversion of more complex molecules. One desirable type of catalytic reaction is the reduction of carboxylic acids that are produced from biomass feedstocks to their corresponding alcohols. The proposed research explores the fundamental importance of hydrogen spillover on a multifunctional catalyst for carboxylic acid reduction with H 2 composed of metal particles coupled to metal oxide particles. Recent work has demonstrated the excellent performance of supported tungsten oxide clusters for carboxylic acid reduction, but only after they are promoted with a late transition metal such as palladium. Elucidating the active state of the catalyst and the associated reaction mechanism for acid reduction on that active state are the overall goals of the proposed project and successful completion will enable future design of efficient multifunctional catalysts. The critically important role of the metal promoter is hypothesized to be its ability to dissociate H2 and spillover atomic H to the support. Although hydrogen spillover is a well-recognized phenomenon in catalysis, its role in both catalyst activation and catalytic turnover are still unresolved. The study combined materials synthesis, characterization, reactivity testing, and molecular simulations, to explore the effect of hydrogen chemical potential on the formation of the active catalytic sites and on the steady state catalytic reduction of carboxylic acid. Varying the hydrogen chemical potential through modification of the gas conditions, support composition, and metal loading to modulated the structure and catalytic performance of the reducible metal oxide. Dual function catalysts containing supported Pd and WO x species co-located on a non-reducible carrier (silica) and a reducible carrier (titania) were synthesized and characterized by electron microscopy, temperature-programmed reduction, and chemisorption. Spectroscopic methods such as X-ray absorption and UV-vis were also used to evaluate the catalysts, which were used in the reduction of propionic acid to aldehyde and alcohol. Quantum chemical calculations, including ab initio phase diagrams provided molecular insights into the H spillover phenomenon.

09 BIOMASS FUELS↗

Pt monolayer shell on nitrided alloy core — A path to highly stable oxygen reduction catalyst

The inadequate activity and stability of Pt as a cathode catalyst under the severe operation conditions are the critical problems facing the application of the proton exchange membrane fuel cell (PEMFC). Here we report on a novel route to synthesize highly active and stable oxygen reduction catalysts by depositing Pt monolayer on a nitrided alloy core. The prepared Pt ML PdNiN/C catalyst retains 89% of the initial electrochemical surface area after 50,000 cycles between potentials 0.6 and 1.0 V. By correlating electron energy-loss spectroscopy and X-ray absorption spectroscopy analyses with electrochemical measurements, we found that the significant improvement of stability of the Pt ML PdNiN/C catalyst is caused by nitrogen doping while reducing the total precious metal loading.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Nano-Array Integrated Structured Catalysts: A New Paradigm upon Conventional Wash-Coated Monolithic Catalysts?

The monolithic catalyst, namely the structured catalyst, is one of the important categories of catalysts used in various fields, especially in catalytic exhaust after-treatment. Despite its successful application in conventional wash-coated catalysts in both mobile and stationary catalytic converters, washcoat-based technologies are facing multi-fold challenges, including: (1) high Pt-group metals (PGM) material loading being required, driving the market prices; (2) less-than ideal distribution of washcoats in typically square-shaped channels associated with pressure drop sacrifice; and (3) far from clear correlations between macroscopic washcoat structures and their catalytic performance. To tackle these challenges, the well-defined nanostructure array (nano-array)-integrated structured catalysts which we invented and developed recently have been proven to be a promising class of cost-effective and efficient devices that may complement or substitute wash-coated catalysts. This new type of structured catalysts is composed of honeycomb-structured monoliths, whose channel surfaces are grown in situ with a nano-array forest made of traditional binary transition metal oxide support such as Al 2 O 3 , CeO 2 , Co 3 O 4 , MnO 2 , TiO 2 , and ZnO, or newer support materials including perovskite-type ABO3 structures, for example LaMnO 3 , LaCoO 3 , LaNiO, and LaFeO 3 . The integration strategy parts from the traditional washcoat technique. Instead, an in situ nanomaterial assembly method is utilized, such as a hydro (solva-) thermal synthesis approach, in order to create sound structure robustness, and increase ease and complex-shaped substrate adaptability. Specifically, the critical fabrication procedures for nano-array structured catalysts include deposition of seeding layer, in situ growth of nano-array, and loading of catalytic materials. The generic methodology utilization in both the magnetic stirring batch process and continuous flow reactor synthesis offers the nano-array catalysts with great potential to be scaled up readily and cost-effectively. The tunability of the structure and catalytic performance could be achieved through morphology and geometry adjustment and guest atoms and defect manipulation, as well as composite nano-array catalyst manufacture. Excellent stabilities under various conditions were also present compared to conventional wash-coated catalysts.

36 MATERIALS SCIENCE↗

Mesoporous Fe-doped MgO nanoparticles as a heterogeneous photo-Fenton-like catalyst for degradation of salicylic acid in wastewater

Mesoporous Fe-doped MgO nanoparticles were synthesized using a facile sol-gel method and utilized for photo-Fenton-like degradation of salicylic acid (SA). The MgO surface dissolution facilitated an increase in the pH under the reaction conditions that allowed the Fe-MgO catalyst to be active without detectable iron leaching. Under simulated solar radiation, SA was completely degraded with an initial rate constant of 0.048 min -1 at the optimal reaction conditions of 500 ppm loading of 5% Fe-MgO, 20 mM H 2 O 2 concentration, and 50 ppm SA concentration. The catalyst was stable over 5 reaction cycles. The Fe-MgO catalyst was shown to have a surface area up to 171 m 2 /g and contain hematite (Fe 2 O 3 ) nanoparticles with octahedrally coordinated iron catalytic centers, as inferred from diffuse reflectance UV–vis measurements. Post-reaction catalyst characterization showed that some Fe 2+ was present in the catalyst due to the redox cycle during the chain initiation and propagation steps of the reaction.

36 MATERIALS SCIENCE↗

Supported Single Fe Atoms Prepared via Atomic Layer Deposition for Catalytic Reactions

In this work, we report a general strategy to synthesize Fe single-atom catalysts (SACs) on various substrates (e.g., multiwalled carbon nanotubes, SiO 2 , and TiO 2 ) with high Fe loading (>1.5 wt %) by atomic layer deposition (ALD) through optimization of ferrocene (Fe precursor) dose time. Fe/SiO 2 and Fe/TiO 2 SACs were used for CO oxidation reactions and catalytic degradation of a methylene blue (MB) solution, respectively. Compared with reported iron oxide catalysts, the efficiency of Fe/SiO 2 for CO oxidation was more than 2 orders of magnitude higher than the reported values. The photocatalysis experiment demonstrated that TiO 2 nanoparticles, deposited with two cycles of Fe ALD, showed the highest activity and had a more than 6-fold photocatalytic activity enhancement over pure TiO 2 for the degradation of MB. This universal method, optimized Fe ALD, expands the potential applications of Fe SACs on different substrates.

36 MATERIALS SCIENCE↗

Efficient and selective dual-pathway polyolefin hydro-conversion over unexpectedly bifunctional M/TiO 2 -anatase catalysts

The huge scale of plastic waste generation and its environmental consequences drive the demands for catalytic plastic upcycling processes. Here, we report efficient polypropylene (PP) hydro-conversion over Ru and Ni supported on a sol-gel anatase TiO 2 (TiO 2 -A-SG). A small number of Brønsted acid sites on TiO 2 -A-SG enables hydrocracking, improving efficiency, steering the selectivity towards high-valued C 4-20 , and allowing more isomerization, compared to Ru-based monofunctional hydrogenolysis catalysts. The relative contribution of hydrocracking increases with lower hydrogen partial pressure, more branched substrates, and lower Ru loading. Ni/TiO 2 -A-SG exhibits superior hydrocracking activity and selectivity to Ni on conventional Brønsted-acidic supports, particularly zeolites. Further, mechanistic studies shows fast isomerization and sequential ß-scissions caused by strong polymer-catalyst interaction and fast cracking with abundant 3 C. This favors C 4-12 formation and prevents secondary reactions. This work demonstrated a novel, highly efficient noble-metal-free catalyst for plastic waste upcycling, while advancing the mechanistic understanding of polyolefin hydro-conversion.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Insights into Dopant-Mediated Tuning of Silica-Supported Mo Metal Centers for Enhanced Olefin Metathesis

Here, we show that the electronic environment around active Mo centers supported on mesoporous silicates can be tuned by the addition of transition metals creating highly dispersed bimetallic catalysts that display enhanced activity for ethylene + 2-butene metathesis to propylene. The bimetallic catalysts are prepared by incorporating electrophilic Lewis acid metals (M) such as Nb, Ta, Zr, or Hf as dopant promoters into mesoporous KIT-6 supports using a one-pot sol–gel technique followed by impregnation of the Mo species. All the bimetallic Mo/M-KIT-6 catalysts display better activity than monometallic Mo/KIT-6 catalyst (28.7 ± 1.1 mmol (mol Mo s ) –1 ), with (Mo/Nb-KIT-6) catalysts exhibiting maximum propylene formation rates (54.2 ± 0.5 mmol (mol Mo s ) –1 ) at an identical Mo loading.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The Impact of Catalyst Layer Composition and Structure on Performance and Durability of PEMWE Anodes

A study of various compositions of anodes for proton exchange membrane water electrolysis aimed at reducing precious metal content and system costs without compromising performance and durability is presented. A key challenge in current water electrolysis technologies is the reliance on high iridium loadings to ensure sufficient catalytic activity, electronic conductivity, and durability for the oxygen evolution reaction. To address this, catalyst layers based on the stable but kinetically limited rutile phase of iridium oxide are combined with platinum nanoparticles and carbon-based additives to improve structural properties and ink processability. By systematically varying the volume ratios of carbon to precious metals and ionomer to solids, compositional trends have been identified, and significant performance improvements have been achieved. Structural and elemental analysis confirms improved dispersion of platinum and iridium can be achieved, as well as electronic conductivity improvements within the catalyst layer. Polarization curve analysis has shown the ability of added Pt and C to significantly increase catalytic activity. These results highlight the potential positive impact of Pt and C on anode structure, composition, and cell performance.

36 MATERIALS SCIENCE↗

Co-Design of Charge Transport Superhighways to Connect Catalytic Sites in Soft Photoelectrochemical Systems

Efficient photon-to-electron-to-molecule conversion requires multi-length scale control over charge transport pathways, where electronic charges are delivered to catalytic sites under high mass transport flux. A fundamental question is how can we co-design charge transport pathways to promote efficient charge transfer to/from catalytic sites in complex three-dimensional architectures? Soft conducting polymer systems offer exceptional promise to provide three-dimensional charge transport networks, where electrolyte (ion and solvent) can interdiffuse to promote long-lived charge carriers and the molecular nature allows for strategic synthetic design of catalytic sites. Herein we combine theoretical and experimental approaches to investigate the earliest stages of photoelectrochemical deposition of near-surface catalytic sites (Pt) on soft bulk heterojunction polymeric semiconductors composed of a prototype donor (PTB7-Th) and a prototype acceptor (N2200) as a model system towards better understanding molecular catalyst-polymer site interactions. We focus initially on photoelectrochemical deposition of low Pt loadings, nanoparticle sizes (formed by progressive nucleation) below 20 nm, for both density functional theory (DFT) modeling studies and for spectroscopic characterization using surface-sensitive X-ray and UV-photoemission (XPS/UPS). DFT modeling of “n-type” N2200 slabs reveal for the first time that sulfur atoms in the thiophene units serve as the lowest-energy adsorption sites for single Pt atoms, while larger Pt clusters engage more complexly with both thiophene and naphthalene diimide (NDI) core sites. Changes in chemical composition observed by X-ray photoelectron spectroscopy (XPS) support the DFT predictions, and the angle-resolved measurements reveal that Pt nucleation initiates at subsurface sites which appear to be localized active domains that promote charge transport/transfer and enable vertical growth toward the surface. These results suggest that light-activated Pt nanoparticle deposition decorates energetically distinct sites, where photoactivity is dictated by the local energetics of those sites, and the fact that they represent the termini of charge transport “super-highways” – a small percentage of the total volume of the donor/acceptor polymeric active layer which carries most of the photocurrent generated during both Pt deposition and photoelectrochemical HER. We posit that these initial studies provide a foundational strategy for design of catalytic sites in the near surface regions of complex polymeric materials and advancing soft semiconductor-based photoelectrochemical systems. Achieving a nanometer-scale understanding of catalyst deposition and the impact of local composition and energetics on that placement, should ultimately provide the design guidelines (co-design) for a broad array of catalysts at sites that optimize that efficiency and maximize platform durability.

14 SOLAR ENERGY↗

Mercury oxidation in flue gas using gold and palladium catalysts on fabric filters

The feasibility of oxidizing elemental mercury in coal combustion flue gas using catalytic material impregnated onto fabric filters was explored. TiO{sub 2}, Au/TiO{sub 2}, and Pd/Al{sub 2}O{sub 3} were studied based on promising results in previous research. Several fabric coating methods were investigated to determine the best way to load a filter. A spray coat method was found to have the highest initial loading and had the lowest losses after simulated pulse-jet cleaning. The oxidation performance of the catalyst-coated filters was tested using a simulated flue gas in a bench-scale reactor under conditions similar to those found in a baghouse. Au/TiO{sub 2} and Pd/Al{sub 2}O{sub 3} were effective, yielding mercury oxidation ranges of 40-60% and 50-80%, respectively. A 19 kW research combustor equipped with a baghouse was used to fire a range of coals and further test the performance of Pd/Al{sub 2}O{sub 3}. Results obtained warrant further development of this technique as a means of mercury pollution control. 19 refs., 2 figs., 5 tabs.

01 COAL, LIGNITE, AND PEAT↗

Selective and Stable Non-Noble-Metal Intermetallic Compound Catalyst for the Direct Dehydrogenation of Propane to Propylene

A non-noble intermetallic compound catalyst consisting of Ni 3 Ga nanoparticles supported on Al 2 O 3 that exhibits high selectivity (~94%), comparable activity (TOF = 4.7 × 10 –2 s –1 ), good stability (~94% to 81% over the 82 h test), and regenerability in the direct dehydrogenation of propane to propylene at 600 °C has been developed. Through synthesis techniques that stabilize the Ni 3 Ga phase, the surface composition of the catalytic nanoparticles could be tuned by Ni and Ga loading such that improved selectivity toward propylene may be achieved. Comparisons with well-defined silica-supported Ni 3 Ga and NiGa catalysts and Ni 3 Ga/Al 2 O 3 with a range of Ni:Ga loading suggested that a specific surface composition range was most promising for propylene production. Furthermore the presence of Ni at the active particle surface was also found to be critical to drive dehydrogenation and enhance conversion, whereas the presence of Ga was necessary to attenuate the reactivity of the surface to improve selectivity and catalyst stability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Highly Robust and Efficient Blechert-Type Cyclic(alkyl)(amino)carbene Ruthenium Complexes for Olefin Metathesis

The first Blechert-type ruthenium complexes containing cyclic(alkyl)(amino)carbene (CAAC) ligands are reported. Furthermore, these catalysts demonstrate remarkable thermal stability in solution and excellent catalytic performances at low catalytic loading (up to 0.005 mol%) in ring-closing metathesis (RCM), macro-RCM, ring-closing enyne metathesis (RCEYM), cross-metathesis (CM), ethenolysis and ring-opening cross metathesis (ROCM). Moreover, up to 95% ee was obtained in asymmetric ring-opening cross metathesis (AROCM) and 57% ee asymmetric cross-metathesis (ACM)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Characterization of platinum catalyst supported on carbon nanoballs prepared by solution plasma processing

In order to improve the energy-conversion efficiency in fuel cells, the authors loaded Pt nanoparticles on carbon nanoballs (CNBs) by using solution plasma processing (SPP) involving CNB and Pt ion with a protection group. In this study, we employed poly(vinylpyrrolidone) (PVP) or sodium dodecyl sulfate (SDS) to prepare Pt nanoparticles supported on CNB (Pt/CNB) by the SPP, and the electrochemical properties as a catalyst was evaluated by cyclic voltammetry. The carbon nanoballs were prepared by thermal decomposition process of ethylene and hydrogen gases. Color of the solution changed from yellow to dark brown as synthesis time. This change indicates the improvement of dispersibility of CNB. Moreover, transmission electron microscopy images and elemental mapping images showed the Pt nanoparticles supported on CNB. A catalytic activity of the Pt/CNB in use of SDS was shown to be higher than the Pt/CNB prepared with PVP system. The SDS-containing Pt/CNB also showed the higher activity than that obtained by the conventional method.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Carbon-pore-sheathed cobalt nanoseeds: An exceptional and durable bifunctional catalyst for zinc-air batteries

Exceptional and durable catalysts for Zinc-air batteries are plagued by nanoparticle agglomeration. As a proof-of-concept, we designed carbon-pore-sheathed cobalt nanoseeds by loading cobalt nanoparticles into N-doped defective carbon pores. Introduced N-doping, Co-N-C bond and graphitic/graphenic carbon defects endow the catalyst with exceptional catalytic activity. Most importantly, the design of Co confined within carbon pores effectively solved the dilemma of nanomaterial stability. By balancing the high catalytic activity and stable cyclability, this unique catalyst is among the outstanding bifunctional catalysts, with a high ORR half-wave potential of 0.847 V and a low OER potential at 10 mA/cm 2 of 1.593 V. As demonstrated in the full cell, a peak power density of 135 mW/cm 2 at a current density of 200 mA/cm 2 and 450 h of stable cycling performance without fading at a current density of 30 mA/cm 2 was delivered.

25 ENERGY STORAGE↗

Synthesis and Characterization of Mixed-Conducting Corrosion Resistant Oxide Supports

An extensive search and evaluation of electrochemically stable catalyst supports (including metal oxides like RuO2-SiO2, RuO2-TiO2, and ITO was perfomed during the 4 years of the project. The suports were also catalyzed by deposition of Pt and tested for its performance and electrochemical stability in RDE and fuel cell experiments. For testing the electrochemical stability and fuel cell performance of the catalysts and supports, we have employed the protocols in use at the Department of Energy and Nissan Technological Center North America (NTCNA). The use of such procedures allows a precise and reproducible estimation of the performance and stability of the materials and permits comparisons among laboratories and DOE funded projects. RuO2-SiO2 catalyst supports showed no loss in surface area during start-stop stability tests that were performed by cycling the electrode potential between 0 V to 1.8 V for 1000 cycles. Catalyzed support (40% Pt/RuO2-SiO2; 1:1 mole ratio) were tested in a PEFC, resulting in a current density of 750 mA/cm2 at 0.6 Volts, and a maximum power density of 570 mW/cm2. Measurements were conducted at 80 ºC with 75% relative humidity of the inlet gases (H2/O2); Pt loadings were 0.4 mg/cm2 at the cathode and 0.2 mg/cm2 at the anode. Start-stop stability tests for support and catalyzed support performed in RDE and PEFC set-ups have confirmed RuO2-TiO2 support stability. The beginning of life performance was exactly equal to end of life performance (in an MEA that has been subjected to severe start-stop cycling for 10,000 start/stop cycles between 1 V to 1.5 V). This result was in sharp contrast to baseline Pt/C catalyst that showed significant performance deterioration after accelerated stability tests. The Pt/TRO showed minimal loss in performance upon exposure to start-stop cycles. The loss in cell voltage at 1 A/cm2 at 100% RH was almost 700 mV for Pt/C whereas it was only ca. 15 mV for Pt/TRO. 40% RH data (of inlet gases) revealed a similar trend in terms of stability – exceptional stability for Pt/TRO as opposed to very poor stability for Pt/HSAC. These observations were attributed to the much higher stability of the TRO support compared to Carbon. The carbon dioxide concentration in the cathode exit stream during the accelerated degradation test with Pt/TRO (start-stop protocol) was extremely low (between 3 to 10 ppm of CO2). In contrast, the CO2 emission levels from a conventional Pt/C catalyst were found to be approx. 200 ppm. This observation was a clear indicator that the main source of carbon being oxidized to carbon dioxide in an MEA was the carbon catalyst support, and not the gas diffusion layer or the graphite flow fields. Indium tin oxide (ITO) was also evaluated as a catalyst support for PEFCs. Pt/ITO was very stable under start-up/shutdown accelerated degradation protocol (RDE tests in perchloric acid). The ECSA change was less than 4% over 10,000 cycles. The load cycling accelerated protocol (from 0.6 to 0.95 V vs. RHE) resulted in a loss of approximately 34% of the initial ECSA after 10,000 cycles. However, fuel cell testing resulted in a very low performing catalyst. XPS spectroscopy was employed to investigate the changes in the catalysts occuring during fuel cell operation. It was observed a shift of In 3d5/2 and In 3d3/2 peaks towards higher binding energies. This can be explained by the formation of hydroxides or oxy-hydroxides in the surface of the catalyst. O1s spectrum for Pt/ITO catalyst after being operated in the fuel cell, also confirmed the formation of significant amounts of surface hydroxides (12 to 16%). The presence of surface hydroxides in the catalyst increased the electrode resistivity affecting fuel cell performance. NTCNA performed a detailed analysis of transport phenomena (reactants and products to/from the Pt active sites) in both commercial catalyst and Pt/RTO (in order to have a better understanding at the basic level). The proton resistance (Rionomer) in Pt/C and Pt/RTO cathode catalyst layers were 150 and 12 mΩ-cm2, respectively. Pt/RTO catalyst layer has about an order or magnitude lower proton transfer resistance than Pt/C catalyst layer. Since the ionomer/support ratio that was used in formulating the ink for both catalysts was the same (0.9), it is expected that the volumetric coverage of ionomer of both catalysts will be significantly different due to the disparity in the surface areas (Pt/C had ~ 800 m2/g, while Pt/RTO had ~ 50 m2/g). The differences in the ionomer volumetric coverage and the ionomer film thickness may explain the significantly higher proton conductivity in the Pt/RTO catalyst layer when compared to Pt/HSAC. It is therefore very important to optimize the ionomer loadings when synthesizing new catalyst supports (and never rely on values for carbon-based commercial catalysts). Finally, NTCNA has elaborated a cost model for non-carbon support materials considering their durability benefits. Material costs for production of Pt/ RuO2-TiO2 electrodes were compared to Pt/C. RuO2-TiO2 support was more expensive than carbon but the total material cost was still dominated by platinum cost. Though ruthenium is considered a precious metal, its cost is far less than platinum. It should also be noted that ruthenium only makes up 38% of the mass of the support, while the rest is inexpensive TiO2. After considering the durability advantages of Pt/RTO, cost model showed that even with almost double the Pt loading (0.35 vs 0.18 mgPt/cm2), Pt/RTO ($22.7/kWnet) is only slightly more expensive than Pt/C ($21.9/kWnet).

08 HYDROGEN↗