Search NASA⌕ Search

SEARCH · Search NASA

Results for “complex fluid”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43
All sourcesNASA NTRSDOE OSTI
DOE OSTI2016

Consistent Fluid Property Evaluation in RELAP5-3D

Previous investigations have developed and tested a methodology to improve the consistency between used to determine the fluid property derivatives used in the numerical solution scheme and the solution scheme itself. Within a bounding rectangle of the fluid property table for a fluid state point, linear interpolants for both fluid property values and their derivatives are calculated. A weighted average between these interpolants the analytical approximations of the fluid properties and derivatives is formed with a weighting factor between 0.0 and 1.0. This average has shown potential to reduce mass error relating to the fluid properties in RELAP5-3D. This linear interpolation and weighted averaging methodology has been implemented in RELAP5-3D with two additional options that adjust the weighting factor in the average according to the location within the bounding rectangle. The first calculates the weighting factor based only on the position between the left and right internal energy endpoints. The second also factors the position between the upper and lower pressure grid points into the calculation of the weighting factor. The new coding passes verification testing and expanded testing of the various options. Graphs are presented from three kinds of test cases, a two volume basic model, Edward’s O’Brien blowdown, and typical PWR. Some trends of the effect of crossing fluid property table pressure and internal energy grid line are identified and discussed for the simple and Edwards test cases. Preliminary results show that it the consistent fluid methodology can reduce mass error in simple cases, but in more complex input models, there is no clear best.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Modeling supercritical CO2 injection induced rupture of a minor fault embedded in a poroelastic layered reservoir-caprock system

CO2 injection for geologic carbon sequestration involves hydromechanical processes that lead to changes in fluid pressure and stresses that can activate existing faults. This paper presents a new method and workflow of modeling fault activation considering more complex three-dimensional geometry of natural faults using the TOUGH-FLAC multiphase fluid flow and geomechanical simulator. In this method and workflow, FLAC3D mechanical interfaces and TOUGH3 finite volume elements are discretized using computer aided design and gridding software along with a tailored mesh translation routine. The method and workflow are demonstrated with a model of a curved minor fault embedded in a poro-elastic layered reservoir-caprock system. The model is used for a comprehensive sensitivity analysis of fault responses to fault length, injection mass rate, injection schedule, well-fault distance, and well locations versus fault location. Four metrics (CO2 plume, shear state of fault, pressure and stress path at fault monitoring points) are selected to assess CO2 migration, pressure change, and the reactivation of faults. The results reveal that CO2 can bypass around the tip of the minor impermeable fault, building up pressure and poro-elastic stress on both sides that tends to impede fault rupture. Our study shows the benefit of carefully designing the injection to achieve the targeted final storage volume, starting at a relatively low rate for considerable time, and then ramping up the injection rate to the full rate of injection. The initial low injection has two distinct benefits: (1) it allows for the formation of an extensive CO2 plume with a much higher mobility through a low viscosity that will result in a lower pressure for a given injection rate, and (2) it allows for gradual build-up of horizontal poro-elastic stress within the reservoir that will tend to impede activation of steeply dipping faults. The injection scenario starting at a low injection rate, denoted here as conservative injection, can significantly reduce the risk of fault activation as high fluid mobility and reservoir strengthening poro-elastic stress has been established long before reaching the peak injection rates. Moreover, simultaneous injection in two injection wells on both sides of fault can provide further reservoir strengthening through poro-elastic stress buildup acting on a fault under normal faulting stress regime. The findings presented in the paper can provide practical and effective guidance on long-term, safe, and reliable geological CO2 storage.

Cao, Meng↗
NASA NTRS2017

Robonaut 2 and You: Specifying and Executing Complex Operations

Crew time is a precious resource due to the expense of trained human operators in space. Efficient caretaker robots could lessen the manual labor load required by frequent vehicular and life support maintenance tasks, freeing astronaut time for scientific mission objectives. Humanoid robots can fluidly exist alongside human counterparts due to their form, but they are complex and high-dimensional platforms. This paper describes a system that human operators can use to maneuver Robonaut 2 (R2), a dexterous humanoid robot developed by NASA to research co-robotic applications. The system includes a specification of constraints used to describe operations, and the supporting planning framework that solves constrained problems on R2 at interactive speeds. The paper is developed in reference to an illustrative, typical example of an operation R2 performs to highlight the challenges inherent to the problems R2 must face. Finally, the interface and planner is validated through a case-study using the guiding example on the physical robot in a simulated microgravity environment. This work reveals the complexity of employing humanoid caretaker robots and suggest solutions that are broadly applicable.

Baker, William↗
DOE OSTI2023

Uncertainty Quantification for Multiphase Computational Fluid Dynamics Closure Relations with a Physics-Informed Bayesian Approach

Multiphase Computational Fluid Dynamics (MCFD) based on the two-fluid model is considered a promising tool to model complex two-phase flow systems. MCFD simulation can predict local flow features without resolving interfacial information. As a result, the MCFD solver relies on closure relations to describe the interaction between the two phases. Those empirical or semi-mechanistic closure relations constitute a major source of uncertainty for MCFD predictions. In this paper, we leverage a physics-informed uncertainty quantification (UQ) approach to inversely quantify the closure relations’ model form uncertainty in a physically consistent manner. This proposed approach considers the model form uncertainty terms as stochastic fields that are additive to the closure relation outputs. Combining dimensionality reduction and Gaussian processes, the posterior distribution of the stochastic fields can be effectively quantified within the Bayesian framework with the support of experimental measurements. As this UQ approach is fully integrated into the MCFD solving process, the physical constraints of the system can be naturally preserved in the UQ results. Here, in a case study of adiabatic bubbly flow, we demonstrate that this UQ approach can quantify the model form uncertainty of the MCFD interfacial force closure relations, thus effectively improving the simulation results with relatively sparse data support.

42 ENGINEERING↗
DOE OSTI2024

Computational Methods for Multi-Physics Simulation of Melting in Steelmaking

Iron and steel production accounts for approximately 8% of global carbon dioxide (CO) emissions. Pathways to decarbonize include replacing fossil fuels in iron ore reduction and electrifying other steelmaking processes. Iron pellets produced by hydrogen, called Hydrogen Direct Reduced Iron (HDRI), have property differences from those produced using conventional DRI processes. These differences may impact melting in electric arc furnaces (EAF) and other downstream processes. The physical properties of iron pellets vary significantly with temperature during heating, complicating predictions of their behavior. In this project, we seek to develop an integrated simulation, including the fluid flow and convective thermal transport around the pellet particle. We also examine conduction and phase changes within the particle as they impact the melting process. We use adaptive mesh refinement (AMR) to resolve both the changing size of the particle and the complex physics of the interaction between the pellet and the surrounding fluid. We base our simulations on the AMReX-incflo module, which allows large-scale Navier-Stokes simulation while resolving the changing particle size during melting. As we advance our numerical tools, we anticipate an improved understanding of the dynamics of HDRI melting, which will, in turn, accelerate the adoption of low-carbon technologies in the steelmaking industry.

AMReX↗
NASA NTRS1995

Progress in Integrated Fluid/Structure/Controls Computations Using High Fidelity Equations

Aeroelasticity that involves strong coupling of fluids, structures and controls is an important element in designing an aircraft. Computational aeroelasticity using low fidelity methods such as the linear aerodynamic flow equations coupled with the modal structural equations are well advanced. Though these low fidelity approaches are computationally less intensive, they are not adequate for the analysis of aircraft which can experience complex flow/structure interactions. Supersonic transports can experience vortex induced aeroelastic oscillations whereas subsonic transports can experience transonic buffet associated structural oscillations. Both aircraft may experience a dip in the flutter speed at the transonic regime. For accurate aeroelastic computations at these complex fluid/structure interaction situations, high fidelity equations such as the Navier-Stokes for fluids and the finite-elements for structures are needed. Using these high fidelity methods, design quantities such as structural stresses can be directly computed. Computations using these high fidelity equations require state-of-the-art large computational resources. This paper will describe the transition from potential equations to Euler/Navier-Stokes equations for fluids and from modal equations to finite element equations for structures. Complexities associated with grids for moving control surfaces will be discussed. All contents of the paper will be limited to those already presented at domestic conferences within U.S. such as those sponsored by AIAA. It will not include any materials related to HPCCP computational work.

Guruswamy, Guru P.↗
DOE OSTI2019

New approach to electron microscopy imaging of gel nanocomposites in situ

We present that characterization of Au-nanocomposites is routinely done with scattering techniques where the structure and ordering of nanoparticles can be analyzed. Imaging of Poloxamer gel-based Au-nanocomposites is usually limited to cryo-TEM imaging of cryo-microtomed thin sections of the specimen. While this approach is applicable for imaging of the individual nanoparticles and gauging their size distribution, it requires altering the state of the specimen and is prone to artifacts associated with preparation protocols. Use of Scanning Transmission Electron Microscopy (S/TEM) with fluid cell in situ provides an opportunity to analysis of these complex materials in their hydrated state with nanometer resolution, yet dispensing dense gel-based samples onto electron-transparent substrates remains challenging. Here, we show that Poloxamer gel-based Au nanocomposites exhibiting thermoreversible behavior can be imaged in a fully hydrated state using a commercially available fluid cell holder, and we describe a specimen preparation method for depositing femtoliter amounts of gel-based nanocomposites directly onto the 50 nm-thick SiN window membranes. Ultimately, fluid cell S/TEM in situ imaging approach offers a pathway to visualization of individual nanoparticles within a thick gel media while maintaining the hydrated state of the carrier polymeric matrix.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Sensing of fluid viscoelasticity from piezoelectric actuation of cantilever flexural vibration

An experimental method is proposed to measure the rheological properties of fluids. The effects of fluids on the vibration actuated by piezoelectric patches were analyzed and used in measuring viscoelastic properties. Fluid-structure interactions induced changes in the beam vibration properties and frequency-dependent variations of the complex wavenumber of the beam structure were used in monitoring these changes. To account for the effects of fluid-structure interaction, fluids were modelled as a simple viscoelastic support at one end of the beam. The measured properties were the fluid’s dynamic shear modulus and loss tangent. Using the proposed method, the rheological properties of various non-Newtonian fluids were measured. The frequency range for which reliable viscoelasticity results could be obtained was 10–400 Hz. Viscosity standard fluids were tested to verify the accuracy of the proposed method, and the results agreed well with the manufacturer’s reported values. The simple proposed laboratory setup for measurements was flexible so that the frequency ranges of data acquisition were adjustable by changing the beam’s mechanical properties.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2018

Computational Modeling of Hydraulic Properties of a Sheared Single Rock Fracture

Flow through a single mechanically sheared Marcellus shale fracture was investigated computationally and experimentally. To provide a better understanding of the variation of hydraulic and geometrical characteristics of a fracture subjected to shearing, coupled shear flow tests on the fracture for four shearing displacement steps under constant normal stress were performed. At the end of each shearing step, computed tomography (CT) scans with resolution 26.8 μm were obtained and the corresponding fracture geometries were evaluated. The CT images were used to generate full aperture maps of the fracture configuration. In addition, average aperture maps were also created by averaging the full-resolution data over 10 × 10 pixels, smoothing out fine structural details. Computational modeling of water flow through the fractures at different shearing steps was performed using a modified local cubic law approach and the 3D full Navier–Stokes equations with the use of the ANSYS-Fluent software. Both the average aperture maps and full maps were used in these simulations. The experimental pressure drops of the fracture at shearing step 1, which has very small apertures, poorly matched the numerical results, quite likely because the fracture structure was inadequately captured by the scanning resolution. Shearing typically increased the aperture height of the fracture, whose features were then better captured by the CT scan. Good agreement between the experimental data and the numerical results of the full map for shearing step 2 was observed. The simulations were performed for both full and average aperture maps, and the effects of scan resolution and surface roughness on the accuracy of the results were studied. The modified local cubic law and full Navier–Stokes simulations of the averaged map fracture were found to be in good agreement. It was conjectured that this was because the nonlinear losses were insignificant for the smoothed out averaged map fracture. Similar comparisons with those of the full map showed agreement in trends, but there were some quantitative differences. The averaged fracture map simulations also predicted lower pressure drops compared to the full map, particularly for high flow rates. These differences were due to the fine-scale geometrical complexity (surface roughness) of fracture geometry that affects the fluid flow in the fracture. In conclusion, an improved cubic law model was also proposed, and its accuracy was verified by comparing its predictions with those of the Navier–Stokes simulations.

58 GEOSCIENCES↗
DOE OSTI2023

Modeling aqueous association constants and mineral solubilities at subcritical and supercritical temperatures

The need for sustainable power generation has increased interest in the use of hydrothermal fluids for industrial applications. New high-enthalpy geothermal systems and biowaste-to-fuel processes are two relevant examples that employ supercritical fluids which require an in-depth understanding of complex chemical reactions occurring near the supercritical temperature of water (374 °C). As these processes operate in thermodynamic regimes that are not currently covered by a standard molar Gibbs energy of formation model, only empirical fits for single reaction systems are available which limit the use of multi-component phase equilibria calculations that are standard practice for less extreme environments. Here, in this paper, we advance a standard molar Gibbs energy of formation model able to operate in these otherwise inaccessible thermodynamic states to include species needed for key mineral solubility systems and ion association reactions. This work extends a model based on molecular statistical thermodynamics (MST) into four new systems (Na 3 PO 4 -H 2 O, LiOH-H 2 O, KOH-H 2 O, and BaSO 4 -H 2 O) by extending the model to cover 10 new species. For each of these systems, model predictions were consistently within the experimental uncertainties for the new systems covered. A breakdown of MST contributions to the model revealed that electrostatic and hard sphere contributions were key to reproducing density dependencies of standard molar Gibbs energy of formation values around the critical point of water.

42 ENGINEERING↗
DOE OSTI2019

Pore-Scale Analysis of Calcium Carbonate Precipitation and Dissolution Kinetics in a Microfluidic Device

In this work, we have characterized the calcium carbonate (CaCO 3 ) precipitates over time caused by reaction-driven precipitation and dissolution in a micromodel. Reactive solutions were continuously injected through two separate inlets, resulting in transverse-mixing induced precipitation during the precipitation phase. Subsequently, a dissolution phase was conducted by injecting clean water (pH = 4). The evolution of precipitates was imaged in two and three dimensions (2-, 3-D) at selected times using optical and confocal microscopy. With estimated reactive surface area, effective precipitation and dissolution rates can be quantitatively compared to results in the previous works. Our comparison indicates that we can evaluate the spatial and temporal variations of effective reactive areas more mechanistically in the microfluidic system only with the knowledge of local hydrodynamics, polymorphs, and comprehensive image analysis. Here, our analysis clearly highlights the feedback mechanisms between reactions and hydrodynamics. Pore-scale modeling results during the dissolution phase were used to account for experimental observations of dissolved CaCO 3 plumes with dissolution of the unstable phase of CaCO 3 . Mineral precipitation and dissolution induce complex dynamic pore structures, thereby impacting pore-scale fluid dynamics. Pore-scale analysis of the evolution of precipitates can reveal the significance of chemical and pore structural controls on reaction and fluid migration.

58 GEOSCIENCES↗
DOE OSTI2020

Organizing bacterial vortex lattices by periodic obstacle arrays

Recent experiments have shown that the complex spatio-temporal vortex structures emerging in active fluids are susceptible to weak geometrical constraints. This observation poses the fundamental question of how boundary effects stabilize a highly ordered pattern from seemingly turbulent motion. Here we show, by a combination of continuum theory and experiments on a bacterial suspension, how artificial obstacles guide the flow profile and reorganize topological defects, which enables the design of bacterial vortex lattices with tunable properties. To this end, the continuum model is extended by appropriate boundary conditions. Beyond the stabilization of square and hexagonal lattices, we also provide a striking example of a chiral, antiferromagnetic lattice exhibiting a net rotational flow, which is induced by arranging the obstacles in a Kagome-like array. Recent experiments showed that weak geometrical constraints can organize topological defects in turbulent bacterial suspensions. Here, the authors use a continuum model to study the connection between symmetry and stability of emergent vortex patterns and the geometry of constraining pillar arrays.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2014

Distinct optical properties of relativistically degenerate matter

In this paper, we use the collisional quantum magnetohydrodynamic (CQMHD) model to derive the transverse dielectric function of a relativistically degenerate electron fluid and investigate various optical parameters, such as the complex refractive index, the reflection and absorption coefficients, the skin-depth and optical conductivity. In this model we take into accounts effects of many parameters such as the atomic-number of the constituent ions, the electron exchange, electron diffraction effect and the electron-ion collisions. Study of the optical parameters in the solid-density, the warm-dense-matter, the big-planetary core, and the compact star number-density regimes reveals that there are distinct differences between optical characteristics of the latter and the former cases due to the fundamental effects of the relativistic degeneracy and other quantum mechanisms. It is found that in the relativistic degeneracy plasma regime, such as found in white-dwarfs and neutron star crusts, matter possess a much sharper and well-defined step-like reflection edge beyond the x-ray electromagnetic spectrum, including some part of gamma-ray frequencies. It is also remarked that the magnetic field intensity only significantly affects the plasma reflectivity in the lower number-density regime, rather than the high density limit. Current investigation confirms the profound effect of relativistic degeneracy on optical characteristics of matter and can provide an important plasma diagnostic tool for studying the physical processes within the wide scope of quantum plasma regimes be it the solid-density, inertial-confined, or astrophysical compact stars.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2017

Coupling discrete and continuum concentration particle models for multiscale and hybrid molecular-continuum simulations

Hybrid molecular-continuum simulation techniques afford a number of advantages for problems in the rapidly burgeoning area of nanoscale engineering and technology, though they are typically quite complex to implement and limited to single-component fluid systems. We describe an approach for modeling multicomponent hydrodynamic problems spanning multiple length scales when using particle-based descriptions for both the finely-resolved (e.g. molecular dynamics) and coarse-grained (e.g. continuum) subregions within an overall simulation domain. This technique is based on the multiscale methodology previously developed for mesoscale binary fluids [N. D. Petsev, L. G. Leal, and M. S. Shell, J. Chem. Phys. 144, 84115 (2016)], simulated using a particle-based continuum method known as smoothed dissipative particle dynamics (SDPD). An important application of this approach is the ability to perform coupled molecular dynamics (MD) and continuum modeling of molecularly miscible binary mixtures. In order to validate this technique, we investigate multicomponent hybrid MD-continuum simulations at equilibrium, as well as non-equilibrium cases featuring concentration gradients.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Sparse thermal data for cellular automata modeling of grain structure in additive manufacturing

Grain growth in the wake of the melt pool formed during alloy-based additive manufacturing (AM) is complex and multifaceted, depending on parameters governing heat transport, fluid flow, and solidification itself. Cellular automata (CA) models have proven effective in providing computationally efficient and physically sound predictions of grain structure for several AM problems, but their efficiency is tied to the performance of heat transport models. CA models use only a small portion of the problem's temperature data (near the moving melt pool boundary), and much of the CA calculations do not affect the final result due to re-melting of material. Coupling of and communication between heat transport and solidification models, and eliminating operations irrelevant towards final grain structure prediction, will be necessary for using these methods for efficient simulation of large parts. In this work, we introduce a procedure of decoupling the CA from temperature field simulation, using files of relevant temperature data written by the heat transport model. This approach is validated against the standard coupling approach using data obtained through the computational fluid dynamics software OpenFOAM. Negligible differences are seen in grain size, volume, and texture distributions for multilayer simulation of test problems, while the quantity of temperature data for these test problems was reduced by four orders of magnitude (from 100s of GB to 10s of MB) and the code performance sped up by a factor of around 50. Furthermore, variability in microstructure as a function of cell size, substrate, time step, and nucleation parameters is studied, and it is found that cell sizes less than or equal to 1.67 μm and sufficiently small time steps yield Αstatistically equivalent microstructures. Finally, a potential use case for this CA approach—the layer-wise convergence in grain structure starting from extremes in initial grain size—is examined. This approach's ability to simulate expected trends in nucleation and epitaxial grain growth for large regions of microstructure, simulated independently of heat transport models themselves, should prove useful for investigation of various microstructure uncertainties and prediction of part-scale experimental results.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Field responsive mechanical metamaterials

Typically, mechanical metamaterial properties are programmed and set when the architecture is designed and constructed, and do not change in response to shifting environmental conditions or application requirements. Here, we present a new class of architected materials called field responsive mechanical metamaterials (FRMMs) that exhibit dynamic control and on-the-fly tunability enabled by careful design and selection of both material composition and architecture. To demonstrate the FRMM concept, we print complex structures composed of polymeric tubes infilled with magnetorheological fluid suspensions. Modulating remotely applied magnetic fields results in rapid, reversible, and sizable changes of the effective stiffness of our metamaterial motifs.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Lipoprotein Particles in Cerebrospinal Fluid

The brain is the most lipid-rich organ in the body, and the intricate interplay between lipid metabolism and pathologies associated with neurodegenerative disorders is being increasingly recognized. The brain is bathed in cerebrospinal fluid (CSF), which, like plasma, contains lipid-protein complexes called lipoproteins that are responsible for extracellular lipid transport. Multiple CSF lipoprotein populations exist, some of which are produced de novo in the central nervous system and others that appear to be generated from protein constituents that are produced in the periphery. These CSF lipoproteins are thought to play key roles in maintaining lipid homeostasis in the central nervous system, while little else is known due to their limited accessibility and their low abundance in CSF. Recent work has provided new insights into the compositional complexity of CSF lipoprotein families and their metabolism in cerebral circulation. Finally, the purpose of this review is to summarize our current state of knowledge on the composition, origin, and metabolism of CSF lipoproteins.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2015

NSR&D FY15 Final Report. Modeling Mechanical, Thermal, and Chemical Effects of Impact

The main goal of this project is to develop a computer model that explains and predicts coupled mechanical, thermal and chemical responses of HE under impact and friction insults. The modeling effort is based on the LANL-developed CartaBlanca code, which is implemented with the dual domain material point (DDMP) method to calculate complex and coupled thermal, chemical and mechanical effects among fluids, solids and the transitions between the states. In FY 15, we have implemented the TEPLA material model for metal and performed preliminary can penetration simulation and begun to link with experiment. Currently, we are working on implementing a shock to detonation transition (SDT) model (SURF) and JWL equation of state.

36 MATERIALS SCIENCE↗