Search NASA⌕ Search

SEARCH · Search NASA

Results for “compositional”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

Formation of Composite SiC/SiC Joints by Embedded Wire Chemical Vapor Deposition

The joining of ceramic monoliths or composites to date has primarily been limited to the formation of brittle monolithic joints using heterogeneous (dissimilar) materials, similar to brazing in metals. The development of a damage-tolerant joint layer by SiC fiber reinforcements is demonstrated here. Tube workpieces made of SiC fiber-SiC matrix composite are joined using a nonwoven SiC fiber mat densified by embedded wire chemical vapor deposition (EWCVD), creating a fiber-reinforced weld-like joint by homogeneous joining. EWCVD uses a localized heating method to target deposition and growth to the joint region specifically, while minimizing thermal damage to the surrounding composite tube material. X-ray computed tomography (XCT) is used to nondestructively characterize as-made joints for relative density, adhesion, and composition. In situ XCT analysis during mechanical testing revealed crack deflections in the bonding layer, which indicates a toughening mechanism typical of ceramic matrix composite phase. Gas permeation testing of these proof-of-concept composite joints identified relatively high leak rates in comparison to fully coated SiC/SiC composite tube workpieces. In conclusion, the novelty of the composite joining method and current technology challenges, including gas permeability, are discussed in comparison with traditional ceramic joints and materials.

SiC↗

Cold Sintering Process of Composites: Bridging the Processing Temperature Gap of Ceramic and Polymer Materials

Co-sintering ceramic and thermoplastic polymer composites in a single step with very high volume fractions of ceramics seems unlikely, given the vast differences in the typical sintering temperatures of ceramics versus polymers. These processing limitations are overcome with the introduction of a new sintering approach, namely “cold sintering process” (CSP). CSP utilizes a transient low temperature solvent, such as water or water with dissolved solutes in stoichiometric ratios consistent with the ceramic composition, to control the dissolution and precipitation of ceramics and effect densification between room temperature and ≈200 °C. Under these conditions, thermoplastic polymers and ceramic materials can be jointly formed into dense composites. Three diphasic composite examples are demonstrated to show the overall diversity of composite material design between organic and inorganic oxides, including the microwave dielectric Li 2 MoO 4 –(-C 2 F 4 -) n , electrolyte Li 1.5 Al 0.5 Ge 1.5 (PO 4 ) 3 –(-CH 2 CF 2 -) x [-CF2CF(CF3)-] y, and semiconductor V 2 O 5 –poly(3,4-ethylenedioxythiophene) polystyrene sulfonate composites. Cold sintering is more general and shall have a major impact on the processing of composite materials for many different applications, mechanical, thermal, and electronic, to mention a few possibilities. CSP concepts open up new composite material design and device integration schemes, impacting a wide variety of applications.

36 MATERIALS SCIENCE↗

Surface modification of bamboo fiber with sodium hydroxide and graphene oxide in epoxy composites

Bamboo fibers (BFs) have high mechanical properties and are candidate reinforcement for epoxy matrix composites. However, to improve performance, good fiber-matrix interaction is required. In this work, unidirectional long BF reinforced epoxy composites at fiber volume content of 22%, 40%, and 50% were made by compression molding. The 40 v% untreated BF reinforced composites exhibited 107% and 439% increase for flexural strength and modulus, respectively, compared to neat epoxy. Sodium hydroxide (NaOH) treatment was used to modify the surface of the BFs, and then the NaOH modified BFs were coated with graphene oxide (GO). The 40 v% NaOH modified BF composites showed an improvement from 259.9 to 327.5 MPa for flexural strength and from 16.7 to 21.5 GPa for flexural modulus, compared to 40 v% untreated BF composites. Slight improvement in properties up to 334.6 MPa for flexural strength and up to 23.8 GPa for flexural modulus was achieved for composites made of 40 v% NaOH/GO modified BF. Surface modification of BF after the NaOH and NaOH/GO treatment was confirmed by X-ray photoelectron spectroscopy and by scanning electron microscopy, which showed differences on the fiber surface morphology and on the composite fracture surface. This BF surface modification approach with GO has potential to impart other properties beyond mechanical to produce multifunctional composite and lead to the use of sustainable plant fibers as alternatives to synthetic fibers.

36 MATERIALS SCIENCE↗

Synthesis, Luminescence and Thermal Properties of PVA–ZnO–Al{sub 2}O{sub 3} Composite Films: Towards Fabrication of Sunlight-Induced Catalyst for Organic Dye Removal

Poly(vinyl alcohol) (PVA)–ZnO–Al{sub 2}O{sub 3} composite films have been prepared by the addition of different compositions of ZnO and Al{sub 2}O{sub 3} through solvent casting method. Fourier transform infrared spectroscopy (FTIR), ultraviolet–visible spectroscopy (UV–Vis) and photoluminescence spectroscopy (PL) spectra revealed the successful incorporation of ZnO and Al{sub 2}O{sub 3} onto PVA and interactions among ZnO, Al{sub 2}O{sub 3} and PVA molecules. PL data indeed showed the enhanced luminescence property of composite films compared with the PVA. Thermogravimetric analysis (TGA) data showed that thermal stability of PVA–ZnO–Al{sub 2}O{sub 3} composite films could be greatly improved by the incorporation of ZnO and Al{sub 2}O{sub 3} into the system. The glass transition temperature (T{sub g}) were increased for the composite samples using ZnO and Al{sub 2}O{sub 3}. Differential scanning calorimetry (DSC) measurements revealed that the melting temperature (T{sub m}) of PVA–ZnO–Al{sub 2}O{sub 3 }composite films are significantly higher (~ 12 to 25 °C) than PVA. The photocatalytic measurements exhibited better photocatalytic degradation ability of PVA–ZnO–Al{sub 2}O{sub 3} composites over PVA. Such photocatalytic capacity makes the PVA–ZnO–Al{sub 2}O{sub 3} composite films promising candidates for the removal of organic dyes for water purification.

36 MATERIALS SCIENCE↗

The Influence of Fabrication Methods on Structure and Microwave Absorption Property of Fe{sub 3}O{sub 4}/rGO Composites

In this study, flake graphite is used as raw material and oxidized to produce graphene oxide (GO), and then two kinds of ferroferric oxide/reduced graphene oxide (Fe{sub 3}O{sub 4}/rGO) composites are fabricated with one-step and two-step methods, respectively. The influence of composite methods on structure and performance is investigated by FT-IR, XRD, SEM, TEM, and testing of electromagnetic parameters. The results show that there are many advantages in the one-step method for fabrication of Fe{sub 3}O{sub 4}/rGO composite, such as the composite process is simplified, the time is shortened, and the Fe{sub 3}O{sub 4}/rGO composite fabricated with the one-step method has the best microwave impedance matching property in the frequency range of 2.5–6 GHz. At the same time, it can be found that there is the Fe–O–C bond in Fe{sub 3}O{sub 4}/rGO composites fabricated with the one-step method, which results in two ways of physical recombination and chemical bonding between Fe{sub 3}O{sub 4} and rGO sheet particulates. In addition, when the mass ratio of GO and FeCl{sub 3} is 1:10, the R{sub L} value of the Fe{sub 3}O{sub 4}/rGO composite fabricated with the one-step method is minimum, and the increase of sample thickness is beneficial to improve the impedance matching property of Fe{sub 3}O{sub 4}/rGO composite in the frequency range of 2.5–6 GHz.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Single- and Double-Layer Microwave Absorbers of Cobalt Ferrite and Graphite Composite at Gigahertz Frequency

Microwave absorbers of cobalt ferrite and graphite composite have been fabricated to investigate the broadening of absorption frequency by mixing small and large particles and comparing single- and double-layer composites in order to broaden the absorption frequency and to enhance multireflection and scattering of electromagnetic wave. CoO and Fe{sub 2}O{sub 3} precursors were mechanically alloyed and sintered at 800, 900, 1000 and 1100 {sup ∘}C in order to synthesise various particle sizes and shapes. A mixed sample of powders sintered at the above mentioned temperatures was also formed. The morphological, phase, and magnetic properties of these samples were studied. Two series of samples have been synthesised which were single- and double-layer composites. Single-layer composite consisted of mixed particles, and their thickness parameters were varied. Double-layer composite was also prepared with various particle sizes of CoFe{sub 2}O{sub 4} as a layer and graphene as another layer. The effect of these layers as matching and absorbing layer was studied. The degree of crystallinity of CoFe{sub 2}O{sub 4} was increased with increase of sintering temperature. Microstructural study showed the evolution of particle size and shape subjected to sintering temperature. Arrhenius plot showed two stages of growth process with activation energy calculated at 26.85 and 83.091 kJ/mol. The critical size of single domain of this sample plotted from the coercivity against particle size was 63.44 nm. Single-layer composite with mixed particle size was not able to show good electromagnetic (EM)-wave absorption; however double-layer composite showed good return loss. The mechanism of the EM-wave absorption of double-layer composite was discussed in this paper.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Composites Strengthened with Graphene Platelets and Formed in Semisolid State Based on α and α/β MgLiAl Alloys

MgLiAl base composites strengthened with graphene platelets were prepared by semisolid processing of ball-milled alloy chips with 2% of graphene platelets. Composites strengthened with graphene platelets show higher hardness and yield stress than the cast alloys, i.e., 160 MPa as compared to 90 MPa for as-cast alloy MgLi9Al1.5. Mechanical properties for MgLiAl-based composites were similar or higher than for composites based on conventional AZ91 or WE43 alloys. The strengthening however was not only due to the presence of graphene, but also phases resulting from the reaction between carbon and lithium, i.e., Li{sub 2}C{sub 2} carbide. Graphene platelets were located at globules boundaries resulting from semisolid processing for all investigated composites. Graphene platelets were in agglomerates forming continuous layers at grain boundaries in the composite based on the alloy MgLi4.5Al1.5. The shape of agglomerates was more complex and wavy in the composite based on MgLi9Al1.5 alloy most probably due to lithium–graphene reaction. Electron diffraction from the two-phase region α + β in MgLi9Al1.5 indicated that [001]α and [110]β directions are rotated about 4° from the ideal relationship [001] hex || [110] bcc phases. It showed higher lattice rotation than in earlier studies what is most probably caused by lattice slip and rotation during semisolid pressing causing substantial deformation particularly within the β phase. Raman spectroscopy studies confirmed the presence of graphene platelets within agglomerates and in addition the presence mainly of Li{sub 2}C{sub 2} carbides in composites based on MgLi4.5Al1.5 and Mg9Li1.5Al alloys. From the character of Raman spectra refinement of graphene platelets was found in comparison with their initial size. The graphene areas without carbides contain graphene nanoplatelets with lateral dimension close to initial graphene sample. Electron diffraction allowed to confirm the presence of Li{sub 2}C{sub 2} carbide at the surface of agglomerates found from Raman spectroscopy results.

36 MATERIALS SCIENCE↗

Bayesian inference of fiber orientation and polymer properties in short fiber-reinforced polymer composites

Herein we present a Bayesian methodology to infer the elastic modulus of the constituent polymer and the fiber orientation state in a short-fiber reinforced polymer composite (SFRP). The properties are inversely determined using only a few experimental tests. Developing composite manufacturing digital twins for SFRP composite processes, including injection molding and extrusion deposition additive manufacturing (EDAM) requires extensive experimental material characterization. In particular, characterizing the composite mechanical properties is time consuming and therefore, micromechanics models are used to fully identify the elasticity tensor. Hence, the objective of this paper is to infer the fiber orientation and the effective polymer modulus and therefore, identify the elasticity tensor of the composite with minimal experimental tests. To that end, we develop a hierarchical Bayesian model coupled with a micromechanics model to infer the fiber orientation and the polymer elastic modulus simultaneously which we then use to estimate the composite elasticity tensor. We motivate and demonstrate the methodology for the EDAM process but the development is such that it is applicable to other SFRP composites processed via other methods. Our results demonstrate that the approach provides a reliable framework for the inference, with as few as three tensile tests, while accounting for epistemic and aleatory uncertainty. Posterior predictive checks show that the model is able to recreate the experimental data well. The ability of the Bayesian approach to calibrate the material properties and its associated uncertainties, make it a promising tool for enabling a probabilistic predictive framework for composites manufacturing digital twins.

36 MATERIALS SCIENCE↗

Facile and scalable fabrication of polymer-ceramic composite electrolyte with high ceramic loadings

Solid state electrolytes are a promising alternative to flammable liquid electrolytes for high-energy lithium battery applications. In this work polymer-ceramic composite electrolyte membrane with high ceramic loading (greater than 60 vol%) is fabricated using a model polymer electrolyte poly(ethylene oxide) + lithium trifluoromethane sulfonate and a lithium-conducting ceramic powder. The effects of processing methods, choice of plasticizer and varying composition on ionic conductivity of the composite electrolyte are thoroughly investigated. The physical, structural and thermal properties of the composites are exhaustively characterized. We demonstrate that aqueous spray coating followed by hot pressing is a scalable and inexpensive technique to obtain composite membranes that are amazingly dense and uniform. The ionic conductivity of composites fabricated using this protocol is at least one order of magnitude higher than those made by dry milling and solution casting. The introduction of tetraethylene glycol dimethyl ether further increases the ionic conductivity. The composite electrolyte's interfacial compatibility with metallic lithium and good cyclability is verified by constructing lithium symmetrical cells. As a result, a remarkable Li + transference number of 0.79 is discovered for the composite electrolyte.

36 MATERIALS SCIENCE↗

Liquid crystallinity driven highly aligned large graphene oxide composites

Graphene is an emerging graphitic carbon materials, consisting of sp{sup 2} hybridized two dimensinal honeycomb structure. It has been widely studied to incorporate graphene with polymer to utilize unique property of graphene and reinforce electrical, mechanical and thermal property of polymer. In composite materials, orientation control of graphene significantly influences the property of composite. Until now, a few method has been developed for orientation control of graphene within polymer matrix. Here, we demonstrate facile fabrication of high aligned large graphene oxide (LGO) composites in polydimethylsiloxane (PDMS) matrix exploiting liquid crystallinity. Liquid crystalline aqueous dispersion of LGO is parallel oriented within flat confinement geometry. Freeze-drying of the aligned LGO dispersion and subsequent infiltration with PDMS produce highly aligned LGO/PDMS composites. Owing to the large shape anisotropy of LGO, liquid crystalline alignment occurred at low concentration of 2 mg/ml in aqueous dispersion, which leads to the 0.2 wt% LGO loaded composites. - Graphical abstract: Liquid crystalline LGO aqueous dispersions are spontaneous parallel aligned between geometric confinement for highly aligned LGO/polymer composite fabrication. - Highlights: • A simple fabrication method for highly aligned LGO/PDMS composites is proposed. • LGO aqueous dispersion shows nematic liquid crystalline phase at 0.8 mg/ml. • In nematic phase, LGO flakes are highly aligned by geometric confinement. • Infiltration of PDMS into freeze-dried LGO allows highly aligned LGO/PDMS composites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Quaternary heterostructured Ag–Bi{sub 2}O{sub 2}CO{sub 3}/Bi{sub 3.64}Mo{sub 0.36}O{sub 6.55}/Bi{sub 2}MoO{sub 6} composite: Synthesis and enhanced visible-light-driven photocatalytic activity

In this work, a novel quaternary heterostructured Ag–Bi{sub 2}O{sub 2}CO{sub 3}/Bi{sub 3.64}Mo{sub 0.36}O{sub 6.55}/Bi{sub 2}MoO{sub 6} composite was fabricated through a low-temperature solution-phase route. The XRD, SEM, EDX and XPS results indicated the as-prepared sample is a four-phase composite of Bi{sub 2}O{sub 2}CO{sub 3}, Bi{sub 3.64}Mo{sub 0.36}O{sub 6.55}, Bi{sub 2}MoO{sub 6}, and Ag. The photocatalytic activities of the as-synthesized samples were evaluated towards the degradation of phenol red aqueous solution. The results showed that the as-synthesized Ag–Bi{sub 2}O{sub 2}CO{sub 3}/Bi{sub 3.64}Mo{sub 0.36}O{sub 6.55}/Bi{sub 2}MoO{sub 6} photocatalysts displayed much higher photocatalytic activities in comparison with pure Bi{sub 3.64}Mo{sub 0.36}O{sub 6.55}, pure Bi{sub 2}MoO{sub 6}, and Bi{sub 3.64}Mo{sub 0.36}O{sub 6.55}/Bi{sub 2}MoO{sub 6} composite. Among them, the 2.5% Ag–Bi{sub 2}O{sub 2}CO{sub 3}/Bi{sub 3.64}Mo{sub 0.36}O{sub 6.55}/Bi{sub 2}MoO{sub 6} sample performed the best. The enhanced photocatalytic activity of the composite photocatalyst was attributed predominantly to the efficient separation of photoinduced electrons and holes. In addition, Ag nanoparticles were photodeposited on the surface of the composite to increase visible-light absorption via the surface plasmon resonance, which is also beneficial to the enhancement of photocatalytic performance. The possible photocatalytic mechanism of the quaternary heterostructure was also discussed in detail. - Graphical abstract: Quaternary heterostructured Ag–Bi{sub 2}O{sub 2}CO{sub 3}/Bi{sub 3.64}Mo{sub 0.36}O{sub 6.55}/Bi{sub 2}MoO{sub 6} were fabricated. The as-synthesized Ag–Bi{sub 2}O{sub 2}CO{sub 3}/Bi{sub 3.64}Mo{sub 0.36}O{sub 6.55}/Bi{sub 2}MoO{sub 6} photocatalysts displayed much higher photocatalytic activities in comparison with pure Bi{sub 3.64}Mo{sub 0.36}O{sub 6.55}, pure Bi{sub 2}MoO{sub 6}, and Bi{sub 3.64}Mo{sub 0.36}O{sub 6.55}/Bi{sub 2}MoO{sub 6} composite. - Highlights: • Quaternary heterostructured Ag–Bi{sub 2}O{sub 2}CO{sub 3}/Bi{sub 3.64}Mo{sub 0.36}O{sub 6.55}/Bi{sub 2}MoO{sub 6} composites were fabricated. • Ag–Bi{sub 2}O{sub 2}CO{sub 3}/Bi{sub 3.64}Mo{sub 0.36}O{sub 6.55}/Bi{sub 2}MoO{sub 6} samples were characterized by various characterization technologies. • Ag–Bi{sub 2}O{sub 2}CO{sub 3}/Bi{sub 3.64}Mo{sub 0.36}O{sub 6.55}/Bi{sub 2}MoO{sub 6} composites presented excellent photocatalytic performances.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Compositionally graded Fe{sub (1−x)}-Pt{sub (x)} nanowires produced by alternating current electrodeposition into alumina templates

Fe{sub (1−x)}-Pt{sub (x)} (0<x<1) compositionally graded nanowires (50 nm in diameter and 1 µm in length) were fabricated by alternating current (AC) electrodeposition into nanoporous aluminum oxide templates through a systematic approach. The effect of AC electrodeposition parameters such as frequency, voltage and electrolyte concentration on morphology and chemical composition of Fe-Pt alloy nanowires was studied. Based on experimental data, AC sine wave deposition at an intermediate voltage of 12 V{sub rms} and a frequency of 50 Hz, produces nanowires with nearly stoichiometric composition (Fe{sub 42}Pt{sub 58}) and a reasonably good uniformity of pore filling. However, there is a gradual change of composition in Fe-Pt alloy nanowires along the length under certain AC parameters. The observed dependency of alloy composition on the deposition voltage and frequency of AC electrodeposition is explained by an interplay between reduction potentials and diffusion coefficients of Fe and Pt ions which makes FePt system able to access compositionally graded nanowires. Magnetic measurements of nanowires of as-deposited nanowires confirm that maximum coercivity of 1.55 kOe is observed for nearly stoichiometric composition which increases up to 1.81 kOe after thermal annealing at 550 °C. - Graphical abstract: Evaluation of synthesizing extrinsic parameters (such as deposition voltages and frequency) and intrinsic parameters (diffusion coefficient and reduction potential of ion species) in compositionally graded Fe{sub (1−x)}-Pt{sub (x)} nanowires prepared by alternating current electrodeposition into alumina templates.

36 MATERIALS SCIENCE↗

Effect of heat treatment on microstructure and interface of SiC particle reinforced 2124 Al matrix composite

The microstructure and interface between metal matrix and ceramic reinforcement of a composite play an important role in improving its properties. In the present investigation, the interface and intermetallic compound present in the samples were characterized to understand structural stability at an elevated temperature. Aluminum based 2124 alloy with 10 wt.% silicon carbide (SiC) particle reinforced composite was prepared through vortex method and the solid ingot was deformed by hot rolling for better particle distribution. Heat treatment of the composite was carried out at 575 °C with varying holding time from 1 to 48 h followed by water quenching. In this study, the microstructure and interface of the SiC particle reinforced Al based composites have been studied using optical microscopy, scanning electron microscopy (SEM) coupled with energy dispersive X-ray spectroscopy (EDS), electron probe micro-analyzer (EPMA) associated with wavelength dispersive spectroscopy (WDS) and transmission electron microscopy (TEM) to identify the precipitate and intermetallic phases that are formed during heat treatment. The SiC particles are uniformly distributed in the aluminum matrix. The microstructure analyses of Al–SiC composite after heat treatment reveal that a wide range of dispersed phases are formed at grain boundary and surrounding the SiC particles. The energy dispersive X-ray spectroscopy and wavelength dispersive spectroscopy analyses confirm that finely dispersed phases are CuAl{sub 2} and CuMgAl{sub 2} intermetallic and large spherical phases are Fe{sub 2}SiAl{sub 8} or Al{sub 15}(Fe,Mn){sub 3}Si. It is also observed that a continuous layer enriched with Cu and Mg of thickness 50–80 nm is formed at the interface in between Al and SiC particles. EDS analysis also confirms that Cu and Mg are segregated at the interface of the composite while no carbide is identified at the interface. - Highlights: • The composite was successfully heat treated at 575°C for 1-48 hrs. • A layer of 50-75 nm is formed at interface after heat treatment. • No Carbide formation and SiC dissolution is observed at this temperature. • MgAl{sub 2}O{sub 4}, CuMgAl{sub 2} phases are segregated at interface of Al-SiC composite. • Mg and Cu are also segregated at near to the grain boundary.

36 MATERIALS SCIENCE↗

Preparation, microstructure and properties of AlN/CBC composites

Highlights: • AlN/CBC composites can be prepared by gelcasting and pressureless sintering method. • Suitable sintering additive content and increasing sintering temperature help to improve properties of composite. • Relative density, C content and microstructure et al. have effect on properties of composite. - Abstract: Gelcasting method with nontoxic biopolymer as gel former can be used to prepare ceramics with complex shape. AlN ceramic bonded carbon (AlN/CBC) composites with light weight were fabricated by gelcasting and pressureless sintering method using nontoxic agarose as gel former with Y{sub 2}O{sub 3} + CaF{sub 2} as sintering additive. The effect of sintering additive content and sintering temperature on the microstructure, flexural strength and thermal conductivity of composites was investigated. The results reveal that, as the temperature decreases, the raw powders solidify into three-dimensional net structures through abundant hydrogen bonds in the agarose. High sintering temperature facilitates densification and improves mechanical and thermal properties of the composites. Increasing sintering additive content can also tune the density and raise flexural strength. The AlN/CBC composite containing 7 wt% sintering additive content, which was sintered at 2000 °C, exhibits the highest thermal conductivity. Relative density, C content and microstructure uniformity have effects on properties of AlN/CBC composite.

36 MATERIALS SCIENCE↗

Research on the interfacial structure and property improvement of the Cfiber/2Si-B-3C-N ceramic matrix composite

Highlights: • The C{sub fiber}/2Si-B-3C-N composite with nice properties was successfully prepared. • ZrO{sub 2} promotes the densification process, homogeneous nucleation and grain growth. • The interface reaction in the composite was well controlled by the addition of ZrO{sub 2}. • The damage to carbon fiber was largely avoided by the addition of ZrO{sub 2}. - Abstract: A mixture of the mechanically alloyed 2Si-B-3C-N powder and short carbon fiber was hot pressed at 1800 °C for 30 mins in nitrogen. Careful investigation to the prepared C{sub fiber}/2Si-B-3C-N ceramic matrix composite revealed that the composite was very difficult to be densified. Heterogeneous nucleation, abnormal grain growth and severe interface reaction occurred on the fiber surface or between the fiber and the ceramic matrix, leading to a small density and weak mechanical properties of the composite. For the prepared composite without any additive, the relative density, flexural strength, elastic modulus and fracture toughness is 71.7%, 64.6 MPa, 14.7 GPa and 1.47 MPa·m{sup 1/2}, respectively. The average size of the SiC grains close to and far away from the carbon fiber is 249.10 nm and 50.45 nm, respectively. However, with the addition of ZrO{sub 2} (7.5 mol%), the above mentioned phenomenons are changed noticeably, and those properties are significantly increased to 88.5%, 112.4 MPa, 111.1 GPa and 2.94 MPa·m{sup 1/2}, respectively. At the same time, the SiC grains close to or far away from the carbon fiber almost have the same average size of about 448.21 nm, and almost no interface reaction occurs. It shows that the addition of ZrO{sub 2} not only facilitates the sintering and densification process, but also depresses the interface reaction, promotes the homogeneous nucleation and grain growth, and hence significantly improves the mechanical properties of the C{sub fiber}/2Si-B-3C-N composite. This interesting finding is favorable for the preparation of carbon fiber reinforced ceramic matrix composite, which requires both a large relative density and well controlled interface reaction.

36 MATERIALS SCIENCE↗

Synthesis, structure and electrochemical properties of polyaniline/MoO{sub 3} nanobelt composite for lithium battery

Graphical abstract: Hydrothermal method was introduced for the synthesis of MoO{sub 3} nanobelts and polyaniline (PANI)/MoO{sub 3} nanobelt composites. The structure and morphology of the samples were studied by X-ray diffraction (XRD), Fourier transform infrared radiation (FTIR), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) analysis. We can see the presence of polyaniline on the MoO{sub 3} nanobelts surface in the TEM pictures as shown in Fig. (a). The pure MoO{sub 3} nanobelts exhibit the initial specific capacity 276 mAhg{sup −1}, whereas PANI/MoO{sub 3} nanobelt composite shows little low initially 228 mAhg{sup −1} after that it has more stabilized specific capacity with increasing cycle numbers as shown in Fig. (b). The cyclic voltammograms of the PANI/MoO{sub 3} nanobelt composite show better cyclic performance compared to pure MoO{sub 3} nanobelts. The electrochemical impedance spectres were studied for both the pure and PANI/MoO{sub 3} samples at 2.0 and 3.5 potentials. The role of the PANI polymeric component of the composite material seems to be the stabilization of the specific capacity due to probable homogeneous distribution of the induced stress during cycling. Display Omitted Highlights: ► Hydrothermal synthesis of MoO{sub 3}, PANI/MoO{sub 3} nanobelts. ► Samples were characterised by XRD, FTIR, DSC, SEM, TEM, CV and impedance. ► MoO{sub 3} nanobelts cathode battery shows initial specific capacity 276 mAhg{sup −1}. ► PANI/MoO{sub 3} nanobelts show initial specific capacity 228 mAhg{sup −1} but high stability. ► PANI/MoO{sub 3} sample studies by impedance at the potentials of 2.0 and 3.5 V. -- Abstract: The MoO{sub 3} nanobelts and polyaniline (PANI)/MoO{sub 3} nanobelt composite were synthesized using hydrothermal method. The crystal structure and morphology of the samples were studied by X-ray diffraction (XRD), Fourier transform infrared radiation (FTIR), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Differential scanning calorimetric (DSC) and thermo gravimetric (TG) measurements were carried out for PANI/MoO{sub 3} nanobelt composite. The pure MoO{sub 3} nanobelts exhibit the initial specific capacity 276 mAhg{sup −1}, whereas PANI/MoO{sub 3} nanobelt composite showed little low initially 228 mAhg{sup −1} after that it has more stabilized specific capacity with increasing cycle numbers at constant current density of 30.7 mAg{sup −1} in the potential range 1.0–4.0 V vs. Li/Li{sup +}. The electrochemical impedance profiles were also studied. The cyclic voltammograms of the PANI/MoO{sub 3} nanobelt composite showed better cyclic performance as compared with pure MoO{sub 3} nanobelts, this is due to the role of PANI polymeric component stabilization of the specific capacity by homogeneous distribution within nanobelts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

One-step synthesis of homogeneous BaFe{sub 12}O{sub 19}/Y{sub 3}Fe{sub 5}O{sub 12} composite powders

Highlights: • A simple one-step sol–gel method was used to synthesize composite magnets. • The composite powders show good homogeneity and exchange coupling. • The M{sub r}/M{sub s} value increases with the BaM concentration. - Abstract: BaFe{sub 12}O{sub 19}/Y{sub 3}Fe{sub 5}O{sub 12} (BaM/YIG) composite powders were synthesized via a simple one-step sol–gel method. The phase composition and morphology of the as-synthesized composite powders were characterized using an X-ray diffractometer and a scanning electron microscopy equipped with energy dispersive X-ray spectroscopy. The magnetic properties of the composite powders were investigated by a vibrating sample magnetometer. Compared with the composite powders prepared by the conventional physical mixing method, the BaM/YIG composite powders show better homogeneity and exchange coupling.

36 MATERIALS SCIENCE↗

Dielectric and magnetic properties of xCoFe{sub 2}O{sub 4}–(1 − x)[0.5Ba(Zr{sub 0.2}Ti{sub 0.8})O{sub 3}–0.5(Ba{sub 0.7}Ca{sub 0.3})TiO{sub 3}] composites

Highlights: • Spinel–perovskite xCoFe{sub 2}O{sub 4}–(1 − x)(0.5Ba(Zr{sub 0.2}Ti{sub 0.8})O{sub 3}–0.5(Ba{sub 0.7}Ca{sub 0.3})TiO{sub 3}) composites have been synthesized by solid state reaction method. • Two anomalies in dielectric constant have been identified, and the composites show relaxor behaviour. • The magnetic properties of the composites improve with increasing concentration of CoFe{sub 2}O{sub 4}. • Enhanced magnetodielectric effect is found, and magnetoelectric coupling has been confirmed by Δϵ ∼ γM{sup 2} relation. • Optical band gap energy of these composites has been reported for the first time. - Abstract: xCoFe{sub 2}O{sub 4}–(1 − x)(0.5Ba(Zr{sub 0.2}Ti{sub 0.8})O{sub 3}–0.5(Ba{sub 0.7}Ca{sub 0.3})TiO{sub 3}) composites with x = 0.1, 0.2, 0.3 and 0.4 have been synthesized by solid state reaction method. X-ray diffraction analysis and field emission secondary electron microscopy have been used for structural and morphological analysis, respectively. The spinel CoFe{sub 2}O{sub 4} and perovskite 0.5Ba(Zr{sub 0.2}Ti{sub 0.8})O{sub 3}–0.5(Ba{sub 0.7}Ca{sub 0.3})TiO{sub 3} phase could be identified in the composites. Two anomalies in dielectric constant have been identified: first one is close to ferroelectric to paraelectric phase transition of 0.5Ba(Zr{sub 0.2}Ti{sub 0.8})O{sub 3}–0.5(Ba{sub 0.7}Ca{sub 0.3})TiO{sub 3} ceramic and the other lies near the magnetic transition temperature of CoFe{sub 2}O{sub 4}. There is an increase in magnetocapacitance and saturation magnetization of the composites at room temperature with increase in CoFe{sub 2}O{sub 4} content. The magnetoelectric coupling coefficient (γ) was approximated by Δϵ ∼ γM{sup 2} relation. The optical band gap energy of the composites decreases with increase in CoFe{sub 2}O{sub 4} content.

36 MATERIALS SCIENCE↗