Search NASA⌕ Search

SEARCH · Search NASA

Results for “depth profiling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

Waterless TiO{sub 2} atomic layer deposition using titanium tetrachloride and titanium tetraisopropoxide

The surface chemistry for TiO{sub 2} atomic layer deposition (ALD) typically utilizes water or other oxidants that can oxidize underlying substrates such as magnetic disks or semiconductors. To avoid this oxidation, waterless or oxidant-free surface chemistry can be used that involves titanium halides and titanium alkoxides. In this study, waterless TiO{sub 2} ALD was accomplished using titanium tetrachloride (TiCl{sub 4}) and titanium tetraisopropoxide (TTIP). In situ transmission Fourier transform infrared (FTIR) studies were employed to study the surface species and the reactions during waterless TiO{sub 2} ALD. At low temperatures between 125 and 225 °C, the FTIR absorbance spectra revealed that the isopropoxide species remained on the surface after TTIP exposures. The TiCl{sub 4} exposures then removed the isopropoxide species and deposited additional titanium species. At high temperatures between 250 and 300 °C, the isopropoxide species were converted to hydroxyl species by β-hydride elimination. The observation of propene gaseous reaction product by quadrupole mass spectrometry (QMS) confirmed the β-hydride elimination reaction pathway. The TiCl{sub 4} exposures then easily reacted with the hydroxyl species. QMS studies also observed the 2-chloropropane and HCl gaseous reaction products and monitored the self-limiting nature of the TTIP reaction. Additional studies examined the waterless TiO{sub 2} ALD growth at low and high temperature. Quartz crystal microbalance measurements observed growth rates of ∼3 ng/cm{sup 2} at a low temperature of 150 °C. Much higher growth rates of ∼15 ng/cm{sup 2} were measured at a higher temperature of 250 °C under similar reaction conditions. X-ray reflectivity analysis measured a growth rate of 0.55 ± 0.05 Å/cycle at 250 °C. X-ray photoelectron depth-profile studies showed that the TiO{sub 2} films contained low Cl concentrations <1 at. %. This waterless TiO{sub 2} ALD process using TiCl{sub 4} and TTIP should be valuable to prevent substrate oxidation during TiO{sub 2} ALD on oxygen-sensitive substrates.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Mass densification and defect restoration in chemical vapor deposition silicon dioxide film using Ar plasma excited by microwave

Silicon dioxide (SiO{sub 2}) films formed by chemical vapor deposition (CVD) have been treated with Ar plasma excited by microwave. The changes of the mass densities, carrier trap densities, and thicknesses of the CVD-SiO{sub 2} films with the Ar plasma treatments were investigated. The mass density depth profiles were estimated with X-Ray Reflectivity (XRR) analysis using synchrotron radiation. The densities of carrier trap centers due to defects of Si-O bond network were estimated with X-ray Photoelectron Spectroscopy (XPS) time-dependent measurement. The changes of the thicknesses due to the oxidation of Si substrates were estimated with the XRR and XPS. The mass densities of the CVD-SiO{sub 2} films are increased by the Ar plasma treatments. The carrier trap densities of the films are decreased by the treatments. The thicknesses of the films are not changed by the treatments. It has been clarified that the mass densification and defect restoration in the CVD-SiO{sub 2} films are caused by the Ar plasma treatments without the oxidation of the Si substrates.

36 MATERIALS SCIENCE↗

Surface temperature: A key parameter to control the propanethiol plasma polymer chemistry

In this work, the influence of the substrate temperature (T{sub s}) on the chemical composition of propanethiol plasma polymers was investigated for a given set of plasma conditions. In a first study, a decrease in the atomic sulfur content (at. %S) with the deposition time (t{sub d}) was observed. This behavior is explained by the heating of the growing film during deposition process, limiting the incorporation of stable sulfur-based molecules produced in the plasma. Experiments carried out by controlling the substrate temperature support this hypothesis. On the other hand, an empirical law relating the T{sub s} and the at. %S was established. This allows for the formation of gradient layer presenting a heterogeneous chemical composition along the thickness, as determined by depth profile analysis combining X-ray photoelectron spectroscopy and C{sub 60} ion gun sputtering. The experimental data fit with the one predicted from our empiric description. The whole set of our results provide new insights in the relationship between the substrate temperature and the sulfur content in sulfur-based plasma polymers, essential for future developments.

36 MATERIALS SCIENCE↗

Atomic layer deposition TiO 2 -Al 2 O 3 stack: An improved gate dielectric on Ga-polar GaN metal oxide semiconductor capacitors

This research focuses on the benefits and properties of TiO 2 -Al 2 O 3 nano-stack thin films deposited on Ga 2 O 3 /GaN by plasma-assisted atomic layer deposition (PA-ALD) for gate dielectric development. This combination of materials achieved a high dielectric constant, a low leakage current, and a low interface trap density. Correlations were sought between the films’ structure, composition, and electrical properties. The gate dielectrics were approximately 15 nm thick and contained 5.1 nm TiO 2 , 7.1 nm Al 2 O 3 and 2 nm Ga 2 O 3 as determined by spectroscopic ellipsometry. The interface carbon concentration, as measured by x-ray photoelectron spectroscopy (XPS) depth profile, was negligible for GaN pretreated by thermal oxidation in O 2 for 30 minutes at 850°C. The RMS roughness slightly increased after thermal oxidation and remained the same after ALD of the nano-stack, as determined by atomic force microscopy. The dielectric constant of TiO 2 -Al 2 O 3 on Ga2O3/GaN was increased to 12.5 compared to that of pure Al 2 O 3 (8~9) on GaN. In addition, the nano-stack's capacitance-voltage (C-V) hysteresis was small, with a total trap density of 8.74 × 10 11 cm -2 . The gate leakage current density (J=2.81× 10 -8 A/cm 2 ) was low at +1 V gate bias. These results demonstrate the promising potential of plasma ALD deposited TiO 2 /Al 2 O 3 for serving as the gate oxide on Ga 2 O 3 /GaN based MOS devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of UV curing time on physical and electrical properties and reliability of low dielectric constant materials

This study comprehensively investigates the effect of ultraviolet (UV) curing time on the physical, electrical, and reliability characteristics of porous low-k materials. Following UV irradiation for various periods, the depth profiles of the chemical composition in the low-k dielectrics were homogeneous. Initially, the UV curing process preferentially removed porogen-related CH{sub x} groups and then modified Si-CH{sub 3} and cage Si-O bonds to form network Si-O bonds. The lowest dielectric constant (k value) was thus obtained at a UV curing time of 300 s. Additionally, UV irradiation made porogen-based low-k materials hydrophobic and to an extent that increased with UV curing time. With a short curing time (<300 s), porogen was not completely removed and the residues degraded reliability performance. A long curing time (>300 s) was associated with improved mechanical strength, electrical performance, and reliability of the low-k materials, but none of these increased linearly with UV curing time. Therefore, UV curing is necessary, but the process time must be optimized for porous low-k materials on back-end of line integration in 45 nm or below technology nodes.

36 MATERIALS SCIENCE↗

Full membrane spanning self-assembled monolayers as model systems for UHV-based studies of cell-penetrating peptides

Biophysical studies of the interaction of peptides with model membranes provide a simple yet effective approach to understand the transport of peptides and peptide based drug carriers across the cell membrane. Therein, the authors discuss the use of self-assembled monolayers fabricated from the full membrane-spanning thiol (FMST) 3-((14-((4'-((5-methyl-1-phenyl-35-(phytanyl)oxy-6,9,12,15,18,21,24,27,30,33,37-undecaoxa-2,3-dithiahenpentacontan-51-yl)oxy)-[1,1'-biphenyl]-4-yl)oxy)tetradecyl)oxy)-2-(phytanyl)oxy glycerol for ultrahigh vacuum (UHV) based experiments. UHV-based methods such as electron spectroscopy and mass spectrometry can provide important information about how peptides bind and interact with membranes, especially with the hydrophobic core of a lipid bilayer. Moreover, near-edge x-ray absorption fine structure spectra and x-ray photoelectron spectroscopy (XPS) data showed that FMST forms UHV-stable and ordered films on gold. XPS and time of flight secondary ion mass spectrometry depth profiles indicated that a proline-rich amphipathic cell-penetrating peptide, known as sweet arrow peptide is located at the outer perimeter of the model membrane.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Properties of Cu(In,Ga,Al)Se{sub 2} thin films fabricated by magnetron sputtering

Cu(In,Ga,Al)Se{sub 2} (CIGAS) thin films were studied as an alternative absorber layer material to Cu(In{sub x}Ga{sub 1−x})Se{sub 2}. CIGAS thin films with varying Al content were prepared by magnetron sputtering on Si(100) and soda-lime glass substrates at 350 °C, followed by postdeposition annealing at 520 °C for 5 h in vacuum. The film composition was measured by an electron probe microanalyzer while the elemental depth profiles were determined by secondary ion mass spectrometry. X-ray diffraction studies indicated that CIGAS films are single phase with chalcopyrite structure and that the (112) peak clearly shifts to higher 2θ values with increasing Al content. Scanning electron microscopy images revealed dense and well-defined grains, as well as sharp CIGAS/Si(100) interfaces for all films. Atomic force microscopy analysis indicated that the roughness of CIGAS films decreases with increasing Al content. The bandgap of CIGAS films was determined from the optical transmittance and reflectance spectra and was found to increase as Al content increased.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Influence of oxygen on characteristics of Zn(O,S) thin films deposited by RF magnetron sputtering

Zn(O,S) thin films were successfully deposited by reactive sputtering using Ar and O{sub 2} gas mixtures at 473 K. X-ray diffraction patterns revealed that the well crystallized Zn(O,S) films were deposited with increasing oxygen concentration in O{sub 2}/Ar, resulting in a shift of the Zn peak of 28.5° to a higher angle, closer to the ZnO peak of 34.4°. Zn(O,S) films were composed of grains agglomerated from small particles, which grew gradually with increasing oxygen concentration. The depth profiles and energy dispersive spectroscopy results of the films indicated that the O/(O+S) ratio increased from 0.04 to 0.81, and all Zn(O,S) films were Zn rich with uniform concentrations of each component. X-ray photoelectron spectroscopy revealed that, as the oxygen concentration increased to 2%, the ZnS films were transformed to Zn(O,S) films via substitution of oxygen for sulfur.

36 MATERIALS SCIENCE↗

Ar{sup +}-irradiation-induced damage in hydride vapor-phase epitaxy GaN films

The authors have investigated the electrical characteristics of hydride vapor-phase epitaxy GaN films exposed to Ar{sup +} irradiation, employing Schottky barrier diodes. The Ar{sup +} irradiation tends to largely increase the effective carrier concentration in the near surface region of GaN up to ∼25 nm, due to the generation of donor-type N vacancy defects, compared to the original value before the irradiation. More interestingly, acceptor-type deep-level defects are found to be formed at ∼2.1, ∼2.9, and ∼3.2 eV below the conduction band in the subsequently deeper region, in which Ga vacancies introduced by the Ar{sup +} irradiation are considered to be in-diffused and immediately combined with hydrogen. These N vacancies and hydrogenated Ga vacancies formed are dominantly responsible for changing the depth profiles of the effective carrier concentration via the carrier generation, the carrier trapping, and/or carrier compensation.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Comparative study of the native oxide on 316L stainless steel by XPS and ToF-SIMS

The very thin native oxide film on stainless steel, of the order of 2 nm, is known to be readily modified by immersion in aqueous media. In this paper, X-ray photoelectron spectroscopy (XPS) and time of flight secondary ions mass spectrometry are employed to investigate the nature of the air-formed film and modification after water emersion. The film is described in terms of oxide, hydroxide, and water content. The preferential dissolution of iron is shown to occur on immersion. It is shown that a water absorbed layer and a hydroxide layer are present above the oxide-like passive film. The concentrations of water and hydroxide appear to be higher in the case of exposure to water. A secure method for the peak fitting of Fe2p and Cr2p XPS spectra of such films on their metallic substrates is described. The importance of XPS survey spectra is underlined and the feasibility of C{sub 60}{sup +} SIMS depth profiling of a thin oxide layer is shown.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Three-dimensional imaging of cholesterol and sphingolipids within a Madin-Darby canine kidney cell

Metabolic stable isotope incorporation and secondary ion mass spectrometry(SIMS) depth profiling performed on a Cameca NanoSIMS 50 were used to image the 18 O-cholesterol and 15 N-sphingolipid distributions within a portion of a Madin-Darby canine kidney (MDCK) cell. Three-dimensional representations of the component-specific isotope distributions show clearly defined regions of 18 O-cholesterol and 15 N-sphingolipid enrichment that seem to be separate subcellular compartments. Furthermore, the low levels of nitrogen-containing secondary ions detected at the 18 O-enriched regions suggest that these 18 O-cholesterol-rich structures may be lipiddroplets, which have a core consisting of cholesterol esters and triacylglycerides.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

High-mass heterogeneous cluster formation by ion bombardment of the ternary alloy Au 7 Cu 5 Al 4

The ternary alloy Au 7 Cu 5 Al 4 was irradiated with 0.1–10 keV Ar + and the surface composition analyzed using laser sputter neutral mass spectrometry. Ejected clusters containing up to seven atoms, with masses up to 2000 amu, were observed. By monitoring the signals from sputtered clusters, the surface composition of the alloy was seen to change with 100 eV Ar + dose, reaching equilibrium after 10 nm of the surface was eroded, in agreement with TRIDYN simulation and indicating that the changes were due to preferential sputtering of Al and Cu. Ejected gold containing clusters were found to increase markedly in intensity while aluminum containing clusters decreased in intensity as a result of Ar sputtering. Such an effect was most pronounced for low energy (<1 keV) Ar + sputtering and was consistent with TRIDYN simulations of the depth profiling. As a result, the component sputter yields from the ternary alloy were consistent with previous binary alloy measurements but showed greater Cu surface concentrations than expected from TRIDYN simulations.

36 MATERIALS SCIENCE↗

Native oxide transport and removal during the atomic layer deposition of Ta{sub 2}O{sub 5} on InAs(100) surfaces

Atomic layer deposition (ALD) was used to deposit Ta{sub 2}O{sub 5} on etched and native oxide-covered InAs(100) using pentakis dimethyl amino tantalum and H{sub 2}O at 200–300 °C. The transport and removal of the native oxides during the ALD process was investigated using x-ray photoelectron spectroscopy (XPS). Depositions above 200 °C on etched surfaces protected the interface from reoxidation. On native oxide-covered surfaces, depositions resulted in enhanced native oxide removal at higher temperatures. The arsenic oxides were completely removed above 250 °C after 3 nm of film growth, but some of the As{sub 2}O{sub 3} remained in the film at lower temperatures. Angle-resolved and sputter depth profiling XPS confirmed indium and arsenic oxide migration into the Ta{sub 2}O{sub 5} film at deposition temperatures as low as 200 °C. Continuous removal of both arsenic and indium oxides was confirmed even after the deposition of several monolayers of a coalesced Ta{sub 2}O{sub 5} film, and it was demonstrated that native oxide transport is a prevalent component of the interface “clean-up” mechanism.

36 MATERIALS SCIENCE↗

High temperature deuterium enrichment using TiC coated vanadium membranes

Here, the current technology for hydrogen isotope separation requires enormous capital investment and energy consumption. Palladium-based membranes exhibit hydrogen isotope selectivity and provide a continuous method of isotope enrichment but have high material costs. Here, the authors investigate the potential of titanium carbide thin films coated on vanadium as a low-cost alternative, which enabled operation at high temperatures. Protium and deuterium exhibited nominally identical solubility in TiC coated vanadium over a range of 500–700°C. Permeation tests from 600 to 700°C revealed that protium permeated faster than deuterium, with the separation factor decreasing from 1.34 to 1.15 with increasing temperature. XPS depth-profiling showed a distinct interface between the TiC layer and the V foil in as-fabricated membranes. However, post-test analysis revealed significant V diffusion through TiC and segregation to the surface. Surface limitations resulting from this degradation accounted for changes in flux and may explain why the separation factor was lower than the value of 1.42 expected from high temperature interstitial diffusion of protium/deuterium in vanadium.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Temperature-dependent dielectric function of tantalum nitride formed by atomic layer deposition for tunnel barriers in Josephson junctions

Here, we report the dielectric functions of insulating tantalum nitride (TaN) films deposited by atomic layer deposition (ALD) on 300 mm Si/SiO 2 substrates to evaluate their suitability as tunnel barriers in tantalum-based Josephson junctions (JJs) for superconducting quantum circuits. Temperature-dependent ellipsometric angles were measured for ALD TaN films with nominal thicknesses of 13 and 25 nm at an incidence angle of 70°, over photon energy ranges of 0.03–0.7 eV (80–300 K) and 0.5–6.5 eV (80–600 K). These data were used to develop a dispersion model for insulating ALD TaN that incorporates a Tauc–Lorentz oscillator with an optical bandgap of 1.5–1.8 eV to describe interband transitions. The extracted dielectric function shows insulating behavior (mid-infrared transparency) at all temperatures and for both film thicknesses tested. In particular, ALD TaN does not exhibit infrared absorption due to free carriers, even at elevated temperatures, consistent with the insulating behavior required for a JJ tunnel barrier. Results from transmission electron microscopy (including selected area electron diffraction) and x-ray diffraction are also discussed. Sputter depth-profile x-ray photoelectron spectroscopy shows an N/Ta ratio of ∼1.2 throughout the film. The lower bandgap, low roughness, and thermal stability of ALD TaN compared to AlO x suggest the possibility of fabricating JJs with thicker barriers while achieving critical current densities required for qubits, enabling improved thickness and composition control, reduced topography, and resistance to aging.

36 MATERIALS SCIENCE↗

Evaluation of the accuracy of stopping and range of ions in matter simulations through secondary ion mass spectrometry and Rutherford backscattering spectrometry for low energy heavy ion implantation

The freely available “Stopping and Range of Ions in Matter” (SRIM) code is used for evaluating ion beam ranges and depth profiles. We present secondary ion mass spectrometry and Rutherford backscattering experimental results of Si samples implanted with low energy Sb ions to evaluate the accuracy of SRIM simulations. We show that the SRIM simulation systematically overestimates the range by 2–6 nm and this overestimation increases for larger ion implantation energy. For the lowest energy implantation investigated, here we find up to a 25% error between the SRIM simulation and the measured range. Finally, the ion straggle shows excellent agreement between simulation and experimental results.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

An examination of the performance of molecular dynamics force fields: Silicon and silicon dioxide reactive ion etching

Classical molecular dynamics (MD) simulations of plasma-surface interactions were performed of physical sputtering and reactive ion etching (RIE), with predictions based on several force fields. In this paper, we focus mainly on SiO 2 but include some results for Si substrates as well. Here, we compare predictions from these MD simulations to experimental studies of SiO 2 physical sputtering (by Ar + ions), RIE of Si, and RIE of SiO 2 (both using F atoms and Ar + ions). MD results using different published force fields are compared to reported yields from published vacuum beam experiments. The near-surface depth profiles predicted using different force fields are compared. One motivation for the present study is to document the nature and magnitude of differences in the predictions for selected systems and conditions of practical interest.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Development of a deep potential model for F and CF 2 etching of Si and SiO 2

An understanding of plasma-surface interactions at increasingly smaller scales is invaluable for the development of novel technologies and processing techniques. Molecular dynamics (MD) simulations can provide insights into atomic-scale interactions, though they are restricted by the availability of interatomic potentials. Machine learning methods, such as Deep Potential Molecular Dynamics (DeepMD), provide a systematic framework for the development of accurate and flexible ab initio-based models. In this work, we develop DeepMD models for the ion-enhanced etching of Si and SiO 2 by F and CF 2 radicals. We employ an active learning process to expand the data set on which the model is trained and demonstrate its effect on the model accuracy. The DeepMD results are compared to data from classical MD simulations and experiments. Physical sputtering yields of SiO 2 by Ar + ions show good agreement with previous simulation results using conventional interatomic potentials, though the predicted depth profiles are different. Etching yields are calculated as a function of ion energy and neutral to ion flux ratio for the Ar + ion-enhanced etching of SiO 2 and Si by F atoms, as well as for etching of SiO 2 by CF 2 radicals, showing reasonable agreement with experimental data. Finally, an ion-enhanced surface kinetic model is fitted to the DeepMD etch yields, and the fitted parameters are compared to quantities computed directly from DeepMD simulations. This study illustrates how molecular dynamics simulations using machine learning potentials can provide an accurate model of etching processes relevant to device manufacturing.

Kounis-Melas, Andreas [Princeton Univ., NJ (United↗