Search NASA⌕ Search

SEARCH · Search NASA

Results for “dislocation density”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

Microstructural evolution and phase stability in Nb-containing interstitial Fe-Mn-Co-Cr-C high-entropy alloys: An in-situ synchrotron X-ray diffraction study during laser melting

The influence of Nb on phase stability and microstructural evolution in an interstitial Fe-Mn-Co-Cr-C high-entropy alloy was investigated using in-situ synchrotron X-ray diffraction (SXRD) during laser melting. Scheil-Gulliver simulations predict the formation of σ and γ-f.c.c. phases in all three alloys, along with NbC in Nb-containing compositions. SXRD confirmed the presence of most predicted phases, but the σ phase was absent. Nb promotes crystallite refinement and increases dislocation density, though excessive additions reduce refinement efficiency due to solubility limits and secondary phase formation. Furthermore, Nb addition also enhances ε-h.c.p. phase formation by reducing stacking fault energy through NbC-induced carbon depletion. Analysis of intensity peak evolution reveals that Nb alters preferred grain orientations, reducing {111} γ intensity while enhancing {220} γ , leading to a more isotropic grain distribution. Overall, Nb plays a key role in phase selection, microstructure refinement, and preferred orientation evolution, allowing the tailored microstructure of high-entropy alloys via rapid solidification.

Interstitial high entropy alloys↗

An overview of HR-EBSD techniques for mapping local stress and dislocations in crystalline materials at sub-micron resolution

High resolution electron backscatter diffraction (HR-EBSD) is a technique used to map elastic strain, crystallographic orientation and dislocation density in a scanning electron microscope. Here, this review covers the background and mathematics of this technique, contextualizing it within the broader landscape of EBSD techniques and other materials characterization methods. Several case studies are presented showing the application of HR-EBSD to the study of plasticity in metals, failure analysis in microelectronics and defect quantification in thin films. This is intended to be a comprehensive resource for researchers developing this technique as well as an introduction to those wishing to apply it.

Ruggles, Timothy J. [Sandia National Laboratories ↗

Revealing cyclic hardening mechanism of a TRIP steel by real-time in situ neutron diffraction

Real-time in situ neutron diffraction was performed on a transformation-induced plasticity (TRIP) steel under cyclic loading at room temperature. By Rietveld refinement and single peak analysis, the volume fraction and average stress estimates as well as dislocation density of individual phases (austenite and martensite phase) were derived. The results reveal that the volume fraction of martensite phase, instead of individual phase strengthening, should be accounted for the remarkable secondary cyclic hardening.

Austenitic steels↗

A Denoising Autoencoder for Improved Kikuchi Pattern Quality and Indexing in Electron Backscatter Diffraction

The rapid collection and indexing of electron diffraction patterns as produced via electron backscatter diffraction (EBSD) has enabled crystallographic orientation and structural determination, as well as additional property-determining strain and dislocation density information with increasing speed, resolution, and efficiency. Pattern indexing quality is reliant on the noise of the collected electron diffraction patterns, which is often convoluted by sample preparation and data collection parameters. EBSD acquisition is sensitive to many factors and thus can result in low confidence index (CI), poor image quality (IQ), and improper minimization of fit, which can result in noisy datasets and misrepresent the microstructure. In an attempt to enable both higher speed EBSD data collection and enable greater orientation fit accuracy with noisy datasets, an image denoising autoencoder was implemented to improve pattern quality. Here, we show that EBSD data processed through the autoencoder results in a higher CI, IQ, and a more accurate degree of fit. In addition, using denoised datasets in HR-EBSD cross correlative strain analysis can result in reduced phantom strain from erroneous calculations due to the increased indexing accuracy and improved correspondence between collected and simulated patterns.

36 MATERIALS SCIENCE↗

Resonance ultrasound prediction of residual stress within a hybrid layer for additively manufactured samples

Hybrid additive manufacturing (AM) involves secondary processes or energy sources to alter specified locations within the build volume. Each hybrid step can refine the grain size, increase dislocation density, or modify residual stresses. Typically, the changes in mechanical properties are not confined within a single layer but have a compounding effect on preceding layers. Existing methods of measuring AM residual stress are limited in terms of their sensitivity, or they are destructive measurements. We propose using resonant ultrasound spectroscopy (RUS) to measure the residual stress in hybrid-AM components noninvasively, based on changes to the resonances, compared to a stress-free component. In this paper, we use finite element models to simulate residual stress in hybrid-AM components and to examine the sensitivity of RUS measurements in terms of frequency shifts and mode shapes with respect to single hybrid layers. Then, the RUS results are used to predict stress for a layer at a known location with unknown stress. Here, the approach highlights the capabilities of RUS to address an AM characterization challenge.

36 MATERIALS SCIENCE↗

Spatially resolved texture and microstructure evolution of additively manufactured and gas gun deformed 304L stainless steel investigated by neutron diffraction and electron backscatter diffraction

In this study, we report the characterization of a 304L stainless steel cylindrical projectile produced by additive manufacturing. The projectile was compressively deformed using a Taylor Anvil Gas Gun, leading to a huge strain gradient along the axis of the deformed cylinder. Spatially resolved neutron diffraction measurements on the HIgh Pressure Preferred Orientation time-of-flight diffractometer (HIPPO) and Spectrometer for Materials Research at Temperature and Stress diffractometer (SMARTS) beamlines at the Los Alamos Neutron Science CEnter (LANSCE) with Rietveld and single-peak analysis were used to quantitatively evaluate the volume fractions of the α, γ, and ε phases as well as residual strain and texture. The texture of the γ phase is consistent with uniaxial compression, while the α texture can be explained by the Kurdjumov–Sachs relationship from the γ texture after deformation. This indicates that the material first deformed in the γ phase and subsequently transformed at larger strains. The ε phase was only found in volumes close to the undeformed material with a texture connected to the γ texture by the Shoji–Nishiyama orientation relationship. This allows us to conclude that the ε phase occurs as an intermediate phase at lower strain, and is superseded by the α phase when strain increases further. Furthe, we found a proportionality between the root-mean-squared microstrain of the γ phase, dominated by the dislocation density, with the α volume fraction, consistent with strain-induced martensite α formation. In conclusion, knowledge of the sample volume with the ε phase from the neutron diffraction analysis allowed us to identify the ε phase by electron back scatter diffraction analysis, complementing the neutron diffraction analysis with characterization on the grain level.

304L stainless steel↗

Development of High-Efficiency GaAs Solar Cells Grown on Nanopatterned GaAs Substrates

One approach to reducing the cost of high-efficiency III–V devices involves adding patterned layers to heteroepitaxial or homoepitaxial substrates to facilitate substrate removal and reuse. However, few studies have focused explicitly on high-quality devices grown over patterned substrates, which is required for any cost saving to be beneficial. In this work, we demonstrate the growth of high-efficiency GaAs solar cells on GaAs substrates patterned with an array of nanoscale SiOX mask stripes. We show that reducing the pattern dimensions to submicron length scales with nanoimprint lithography enables defect-free coalescence. By varying the growth conditions, faceting of the epilayer material during overgrowth of the patterned mask was also controlled. A V/III ratio of 200 during MOVPE overgrowth produced smooth coalesced epilayers, which is desirable for the growth of subsequent device layers. Inverted GaAs front homojunction devices grown on patterned GaAs(001) substrates achieved threading dislocation densities below 5 × 10 5 cm –2 and maintained >23% solar cell efficiencies at one sun illumination, equivalent to control devices grown on unpatterned epi-ready substrates.

14 SOLAR ENERGY↗

Radiation-Induced Changes in Single Crystal Calcite and Dolomite: Mineral Analogues of Light Water Reactor, Nuclear Power Plant Concrete Aggregates

Two analogues of aggregates (calcite and dolomite) found in nuclear power plant (NPP) concrete have been neutron irradiated to fluences up to 2 × 10 20 n/cm 2 at 52 °C and 4 × 10 19 n/cm 2 at 95 °C (E > 0.1 MeV). X-ray diffraction studies showed that these aging conditions affected crystallography of both calcite and dolomite, with both showing a growth in their unit cells compared to that of the unirradiated samples. Only dolomite samples showed a continuous increase of its lattice parameters with the increase in irradiation. In calcites, the lattice growth with irradiation dissipated after a fluence of 5 × 10 18 n/cm 2 . Radiation-induced disordering of the crystal structure was observed in both materials, while a healing effect of irradiation temperature was mainly observed in calcites. Dislocation densities calculated by using XRD data also supported these observations. Insights made into the unit cells of both minerals by using Fourier synthesis showed that the Mg sites are more prone to the neutron irradiation than the Ca sites, resulting in larger radiation effects and higher disruption in the crystal structure of dolomite than that of calcite. Furthermore, other than the polycrystalline characteristics observed by using TEM, these minerals did not show complete amorphization or significant structural decomposition at the studied irradiation fluences.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Epitaxial Growth of Three-Dimensionally Mesostructured Single-Crystalline Cu 2 O via Templated Electrodeposition

Significant efforts have been made over the past few decades to realize functional three-dimensional photonic crystal devices including zero-threshold lasers, waveguides, light-emitting diodes (LEDs), and solar cells; however, progress has been limited because of difficulties in creating three-dimensional photonic crystals from single-crystal materials. Most have been formed from polycrystalline materials and thus have generally exhibited poor electronic properties. Realization of materials containing complex three-dimensional mesostructures, in single-crystal form, remains a significant challenge. Furthermore, we demonstrate the epitaxial growth of three-dimensionally mesostructured Cu 2 O by bottom-up electrodeposition through a 3D silica colloidal template. Not only is the templated Cu 2 O single crystal, but when the electrodeposition continues past the colloidal template, the crystallinity of the overlying solid Cu 2 O appears to be improved because the template blocks threading dislocations, resulting in substantial reductions in the dislocation density of the overlying solid Cu 2 O.

36 MATERIALS SCIENCE↗

Experimental Observation of a New Attenuation Mechanism in hcp ‐Metals That May Operate in the Earth's Inner Core

Abstract Seismic observations show the Earth's inner core has significant and unexplained variation in seismic attenuation with position, depth and direction. Interpreting these observations is difficult without knowledge of the visco‐ or anelastic dissipation processes active in iron under inner core conditions. Here, a previously unconsidered attenuation mechanism is observed in zinc, a low pressure analog ofhcp‐iron, during small strain sinusoidal deformation experiments. The experiments were performed in a deformation‐DIA combined with X‐radiography, at seismic frequencies (∼0.003–0.1 Hz), high pressure and temperatures up to ∼80% of melting temperature. Significant dissipation (0.077 ≤ Q −1 (ω) ≤ 0.488) is observed along with frequency dependent softening of zinc's Young's modulus and an extremely small activation energy for creep (⩽7 kJ mol −1 ). In addition, during sinusoidal deformation the original microstructure is replaced by one with a reduced dislocation density and small, uniform, grain size. This combination of behavior collectively reflects a mode of deformation called “internal stress superplasticity”; this deformation mechanism is unique to anisotropic materials and activated by cyclic loading generating large internal stresses. Here we observe a new form of internal stress superplasticity, which we name as “elastic strain mismatch superplasticity.” In it the large stresses are caused by the compressional anisotropy. If this mechanism is also active inhcp‐iron and the Earth's inner‐core it will be a contributor to inner‐core observed seismic attenuation and constrain the maximum inner‐core grain‐size to ≲10 km.

Geochemistry & Geophysics↗

Severe Strain‐Induced Olivine‐Ringwoodite Transformation at Room Temperature: Key to Enigmas of Deep‐Focus Earthquake

Deep‐focus earthquakes at 350–660 km are presumably caused by olivine‐spinel phase transformation (PT). This cannot, however, explain the observed high seismic strain rate, which requires PT to complete within seconds, while metastable olivine does not transform for over a million years. Recent theory quantitatively describes how severe plastic deformations (SPD) can solve this dilemma but lacking experimental proof. Here, we introduce dynamic rotational diamond anvil cell with rough diamond anvils to impose SPD on San Carlos olivine. While olivine never transformed to spinel at room temperature, we obtained reversible olivine‐ringwoodite PT under SPD at 15–28 GPa within tens of seconds. The PT pressure reduces with increasing dislocation density, microstrain, plastic strain, and decreasing crystallite size. Results demonstrate a new strain‐induced PT mechanism compared to a pressure/temperature‐induced one. Combined with SPD during olivine subduction, this mechanism can accelerate olivine‐ringwoodite PT from millions of years to timescales relevant to earthquakes.

Lin, F. [Iowa State Univ., Ames, IA (United States↗

Probing the limits of metal plasticity with molecular dynamics simulations

Ordinarily, the strength and plasticity properties of a metal are defined by dislocations—line defects in the crystal lattice whose motion results in material slippage along lattice planes. Dislocation dynamics models are usually used as mesoscale proxies for true atomistic dynamics, which are computationally expensive to perform routinely. However, atomistic simulations accurately capture every possible mechanism of material response, resolving every “jiggle and wiggle” of atomic motion, whereas dislocation dynamics models do not. We present fully dynamic atomistic simulations of bulk single-crystal plasticity in the body-centred-cubic metal tantalum. Our goal is to quantify the conditions under which the limits of dislocation-mediated plasticity are reached and to understand what happens to the metal beyond any such limit. In our simulations, the metal is compressed at ultrahigh strain rates along its [001] crystal axis under conditions of constant pressure, temperature and strain rate. To address the complexity of crystal plasticity processes on the length scales (85–340 nm) and timescales (1 ns–1μs) that we examine, we use recently developed methods of in situ computational microscopy to recast the enormous amount of transient trajectory data generated in our simulations into a form that can be analysed by a human. Our simulations predict that, on reaching certain limiting conditions of strain, dislocations alone can no longer relieve mechanical loads; instead, another mechanism, known as deformation twinning (the sudden re-orientation of the crystal lattice), takes over as the dominant mode of dynamic response. Below this limit, the metal assumes a strain-path-independent steady state of plastic flow in which the flow stress and the dislocation density remain constant as long as the conditions of straining thereafter remain unchanged. In this distinct state, tantalum flows like a viscous fluid while retaining its crystal lattice and remaining a strong and stiff metal.

36 MATERIALS SCIENCE↗

High temperature deformability of ductile flash-sintered ceramics via in-situ compression

Flash sintering has attracted significant attention as its remarkably rapid densification process at low sintering furnace temperature leads to the retention of fine grains and enhanced dielectric properties. However, high-temperature mechanical behaviors of flash-sintered ceramics remain poorly understood. Here, we present high-temperature (up to 600 °C) in situ compression studies on flash-sintered yttria-stabilized zirconia (YSZ). Below 400 °C, the YSZ exhibits high ultimate compressive strength exceeding 3.5 GPa and high inelastic strain (~8%) due primarily to phase transformation toughening. At higher temperatures, crack nucleation and propagation are significantly retarded, and prominent plasticity arises mainly from dislocation activity. The high dislocation density induced in flash-sintered ceramics may have general implications for improving the plasticity of sintered ceramic materials.

36 MATERIALS SCIENCE↗

Hardening in Au-Ag nanoboxes from stacking fault-dislocation interactions

Porous, nano-architected metals with dimensions down to ~10 nm are predicted to have extraordinarily high strength and stiffness per weight, but have been challenging to fabricate and test experimentally. Here, we use colloidal synthesis to make ~140 nm length and ~15 nm wall thickness hollow Au-Ag nanoboxes with smooth and rough surfaces. In situ scanning electron microscope and transmission electron microscope testing of the smooth and rough nanoboxes show them to yield at 130 ± 45 MPa and 96 ± 31 MPa respectively, with significant strain hardening. A higher strain hardening rate is seen in rough nanoboxes than smooth nanoboxes. Finite element modeling is used to show that the structure of the nanoboxes is not responsible for the hardening behavior suggesting that material mechanisms are the source of observed hardening. Molecular dynamics simulations indicate that hardening is a result of interactions between dislocations and the associated increase in dislocation density.

42 ENGINEERING↗

Influence of ordered L1 2 precipitation on strain-rate dependent mechanical behavior in a eutectic high entropy alloy

Recent studies indicate that eutectic high-entropy alloys can simultaneously possess high strength and high ductility, which have potential industrial applications. The present study focuses on Al 0.7 CoCrFeNi, a lamellar dual-phase ( fcc + B2) precipitation-strengthenable eutectic high entropy alloy. This alloy exhibits an fcc + B2 (B2 with bcc nano-precipitates) microstructure resulting in a combination of the soft and ductile fcc phase together with hard B2 phase. Low temperature annealing leads to the precipitation of ordered L1 2 intermetallic precipitates within the fcc resulting in enhanced strength. The strengthening contribution due to fine scale L1 2 is modeled using Orowan dislocation bowing and by-pass mechanism. The alloy was tested under quasi-static (strain-rate = 10 –3 s –1 ) tensile loading and dynamic (strain-rate = 10 3 s –1 ) compressive loading. Due to the fine lamellar microstructure with a large number of fcc - bcc interfaces, the alloy show relatively high flow-stresses, ~1400 MPa under quasi-static loading and in excess of 1800 MPa under dynamic loading. Interestingly, the coherent nano-scale L1 2 precipitate caused a significant rise in the yield strength, without affecting the strain rate sensitivity (SRS) significantly. These lamellar structures had higher work hardening due to their capability for easily storing higher dislocation densities. The back-stresses from the coherent L1 2 precipitate were insufficient to cause improvement in twin nucleation, owing to elevated twinning stress under quasi-static testing. However, under dynamic testing high density of twins were observed.

36 MATERIALS SCIENCE↗

Alloying effects on deformation induced microstructure evolution in copper

In this work, we investigated the effects of alloying elements on plastic deformation and microstructure evolution in polycrystalline copper (Cu) and Cu alloyed with 1 wt. % lead (Cu-1 %Pb). These materials were selected due to the size mismatch between Cu and Pb, with the latter forming precipitates at grain boundaries. Multi-modal characterization techniques, including neutron diffraction, electron backscatter diffraction (EBSD), and transmission electron microscopy (TEM), along with finite element simulations were employed to study the deformation behavior across multiple length scales. While both Cu and Cu-1%Pb exhibited similar macroscale response and final deformation textures, both dislocation line profile analysis and TEM revealed increased dislocation density in deformed Cu-1%Pb specimens. The presence of lead precipitates also significantly affected local plastic deformation during compression, with their influence diminishing with increasing strain. These results demonstrate the complex relationships between alloying elements, plastic deformation, microstructural evolution, and material behavior under load. The insights gained from this multi-scale and multi-technique approach contribute to the fundamental understanding of microstructural evolution in immiscible alloys and are valuable for tailoring the properties of structural materials for specific engineering applications.

36 MATERIALS SCIENCE↗

Energy-resolved neutron imaging and diffraction including grain orientation mapping using event camera technology

Time-of-flight neutron diffraction and energy-resolved imaging each provide unique perspectives into material properties. Neutron diffraction is useful for assessing microstructural parameters such as phase composition, texture, and dislocation densities, though it typically provides averaged data over the sampled volume. Energy-resolved imaging, on the other hand, offers both spatial and spectral information by detecting Bragg edges and neutron absorption resonances, which enables detailed mapping of microstructure and isotopic composition. When combined, these techniques have the potential to enrich our understanding of material behavior across different scales, enhancing our understanding of complex materials. Traditionally, these modalities are conducted on separate instruments, which is time-consuming and poses challenges for data integration. Here, we report the integration of the LumaCam, an event-mode energy-resolved neutron imaging camera with the HIPPO time-of-flight diffractometer at LANSCE. This integration enables simultaneous diffraction and imaging across the full spectrum, with analysis optimized for diffraction and Bragg-edge imaging in the thermal range (0.45–10 Å) and resonance imaging in the epithermal range (0.5–3000 eV), facilitating comprehensive multi-modal analysis. We demonstrate its capabilities through case studies, including spatial mapping of grain orientations in a steel sample and accurate thickness estimations for irregular samples including a depleted uranium cylinder and a natural silver-containing mineral specimen. The combined setup enhances real-time sample alignment and provides comprehensive data for crystal structure, texture, and isotopic composition analysis. This approach opens new possibilities for advanced applications in nuclear engineering, archaeology, and materials science.

36 MATERIALS SCIENCE↗

Martensite decomposition during rapid heating of Ti-6Al-4V studied via in situ synchrotron X-ray diffraction

Martensite, α‘, commonly appears in Ti-6Al-4V upon rapid cooling from above the β-transus temperature. It is known that α‘ decomposes into α and β at high temperatures but well below the β-transus temperature. Here, we study the decomposition of martensitic Ti-6Al-4V under rapid laser heating, employing in situ synchrotron X-ray diffraction. A comparison is made with post-annealed Ti-6Al-4V under heating to elucidate changes without martensite decomposition. The fast acquisition of X-ray diffraction data at 250 Hz temporally resolves the decomposition process initiated by annihilating dislocations in α‘. The recovery process is accompanied by structural changes in martensite, followed by the phase transformation to β. Thermal profiles estimated from the lattice parameter data reveal the influence of heating rates and dislocation densities on the decomposition process. Throughout the analysis of the diffraction profiles with respect to estimated temperature, we propose a straightforward method for approximating the initiation temperature of martensite decomposition.

42 ENGINEERING↗