Search NASA⌕ Search

SEARCH · Search NASA

Results for “fracture simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

CT scanning and flow measurements of shale fractures after multiple shearing events

A shearing apparatus was used in conjunction with a Hassler-style core holder to incrementally shear fractured shale cores while maintaining various confining pressures. Computed tomography scans were performed after each shearing event, and were used to obtain information on evolving fracture geometry. Fracture transmissivity was measured after each shearing event to understand the hydrodynamic response to the evolving fracture structure. The digital fracture volumes were used to perform laminar single phase flow simulations (local cubic law with a tapered plate correction model) to qualitatively examine small scale flow path variations within the altered fractures. Fractures were found to generally increase in aperture after several shear slip events, with corresponding transmissivity increases. Lower confining pressure resulted in a fracture more prone to episodic mechanical failure and sudden changes in transmissivity. Conversely, higher confining pressures resulted in a system where, after an initial setting of the fracture surfaces, changes to the fracture geometry and transmissivity occurred gradually. Flow paths within the fractures are largely controlled by the location and evolution of zero aperture locations. Lastly, a reduction in the number of primary flow pathways through the fracture, and an increase in their width, was observed during all shearing tests.

04 OIL SHALES AND TAR SANDS↗

Flow behavior of hydraulic fractured tight formations considering Pre-Darcy flow using EDFM

For tight reservoirs/formations, flow in fracture and matrix obey different flow patterns. Pre-Darcy flow always exists in low permeability subsurface porous media while Darcy flow can be applied in fracture. It is an outstanding challenge to understand the flow behavior coupling different flow mechanisms. As numerical simulation can predict field-scale performance so the development of efficient simulation method becomes a key issue to evaluate the flow behavior. In this paper, we develop an improved discrete fracture model based on the widely used embedded discrete facture model (EDFM) to simulate the transport both in homogenous and heterogeneous porous media in the presence of Pre-Darcy flow. The conservation equations are derived for fracture and matrix firstly and then discretized by fully implicit method. The transmissibility of different connection types is defined and the detailed calculation workflow is presented as well. The proposed model is verified through the comparison with the model using local grid refined (LGR) method. It is discovered that our simulation method exhibits good accuracy when analyzing the effect of Pre-Darcy flow. Some examples are shown including 1D scalar transport, 2D heterogeneous, 3D flow, complex fracture system and multiple well system problems with fully-coupled flow in fracture and matrix. The pressure distribution and well flux are demonstrated to analyze the Pre-Darcy flow characteristics. Results indicate that the new model works robustly for different flow problems which provide further insight into the Pre-Darcy flow in low permeability media.

02 PETROLEUM↗

Influences of temperature on permeability changes of flow-paths altered by highly alkaline Ca-rich groundwater - 15192

Fractures (or cracks) in host rock around the geological repository are considered as main flow-paths for the migration of radionuclides. Such fractures would be altered by the alkaline components (Ca, Na, K) leaching from cementitious materials for the construction of the repository. While silicate minerals in fractures are dissolved by highly alkaline groundwater, secondary minerals would deposit on the surface of fractures because of the reaction between the alkaline components and silicate species. The authors' previous study showed the generation of CSH-gel and the clogging of micro flow-path under the condition of Ca-rich and high pH by flow experiments. The present study examined the permeability changes with temperature in micro flow-path flowing highly alkaline Ca-rich solution, considering temperature at the depth of geological disposal system. For the simulation of micro flow-path such as fractures, 'micro flow-cell', which nipped a thin Teflon sheet with a slit between granite chip and Teflon basement, were used for the experiments. Highly alkaline Ca-rich solution (pH>12 and 8.5 mM Ca(OH){sub 2}) were injected into micro flow-cell with 2.0 ml/h of flow rate under the given temperature conditions (278 K, 296 K or 313 K). As a result, the permeability became lower with the increase in temperature. In addition, the deposition rates of CSH-gel became larger with the increase in temperature, and the activation energy was estimated to be 32.0 kJ/mol. These results suggest that flow-paths around the geological repository would undergo the clogging with CSH-gel in a shorter time-period under a condition of higher temperature. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Simulation of flame acceleration and deflagration-to-detonation transition with heat transfer in HE product and fractured HE

A simple heat transfer model has been developed for high explosives. For the gaseous high explosive (HE) product, the Smargorinsky eddy viscosity model has been adopted for estimating the turbulent thermal conductivity. Convective heat transfer in the fractured solid HE is modeled as the effective thermal conduction in the porous media, which is equivalent to the enthalpy flux carried by the velocity determined by Darcy’s law with Forchheimer term.Other features of the model include a multi-reaction chain, equation-of-state for each species involved, and a two-phase hotspot model. Test calculations are performed with various initial disturbances. Onset and progress of flame acceleration (FA) and chemical reactions are strongly affected by the heat transfer and initial disturbance. Staged development of FA also affirms the necessity of modeling based on a multi-reaction chain. When conditions warrant,e.g., stronger initial disturbance, FA evolves to deflagration-to-detonation transition (DDT),demonstrating automatic capture of the DDT.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Evaluation of sintered bauxite proppant for binary enhanced geothermal systems

Abstract Solid granular proppant particles are widely used in oil and gas development to sustain permeability through fractures after hydraulic stimulation. Similar proppants are of interest for geothermal applications where the goal of sustaining permeability is the same, but the harsh geothermal environment risks rapid proppant degradation that will reduce fracture permeability. Here, we present proppant conductivity experiments using saw cut granite, tensile fractured granite, and aluminum control specimens packed with sintered bauxite ceramic proppants at concentrations of 0.0, 0.1, and 1.0 kg/m 2 . Simulated geothermal conditions included temperatures up to 130 °C and normal closure stresses up to 60 MPa. Compared to unpropped specimens, peak fracture conductivity enhancement was up to 6 orders of magnitude. At simulated geothermal conditions, proppants were able to sustain fracture conductivity over 60 h, but chemical dissolution and decreasing permeability over time were evident. Irreversible conductivity reductions with crushing and embedment of proppants during loading stages were also observed. Overall, sintered bauxite proppant remains a promising option for low-temperature binary-cycle enhanced geothermal systems.

58 GEOSCIENCES↗

Wide-range simulation of elastoplastic wave fronts and failure of solids under high-speed loading

The aim of this paper is numerical study of deformation processes and failure of vanadium under shock-wave loading. According developed statistical theory of solid with mesoscopic defects the constitutive equations were proposed in terms of two structural variables characterizing behavior of defects ensembles: defect density tensor and structural scaling parameter. On the basis of wide-range constitutive equations the mathematical model of deformation behavior and failure of vanadium was developed taking into account the bond relaxation mechanisms, multistage of fracture and nonlinearity kinetic of defects. Results of numerical simulation allow the description of the major effects of shock wave propagation (elastic precursor decay, grow of spall strength under grow strain rate)

42 ENGINEERING↗

Wellbore cement fracture permeability as a function of confining stress and pore pressure

Cemented annulus fractures are a major leakage path in a wellbore system, and their permeability plays an important role in the behavior of fluid flow through a leaky wellbore. The permeability of these fractures is affected by changing conditions including the external stresses acting on the fracture and the fluid pressure within the fracture. Laboratory gas flow experiments were conducted in a triaxial cell to evaluate the permeability of a wellbore cement fracture under a wide range of confining stress and pore pressure conditions. For the first time, an effective stress law that considers the simultaneous effect of confining stress and pore pressure was defined for the wellbore cement fracture permeability. Here the results showed that the effective stress coefficient (λ) for permeability increased linearly with the Terzaghi effective stress ( -p) with an average of λ = 1 in the range of applied pressures. The relationship between the effective stress and fracture permeability was examined using two physical-based models widely used for rock fractures. The results from the experimental work were incorporated into numerical simulations to estimate the impact of effective stress on the interpreted hydraulic aperture and leakage behavior through a fractured annular cement. Accounting for effective stress-dependent permeability through the wellbore length significantly increased the leakage rate at the wellhead compared with the assumption of a constant cemented annulus permeability.

58 GEOSCIENCES↗

Investigation of Possible Wellbore Cement Failures During Hydraulic Fracturing Operations

We model and assess the possibility of shear failure, using the Mohr-Coulomb model ? along the vertical well by employing a rigorous coupled flow-geomechanic analysis. To this end, we vary the values of cohesion between the well casing and the surrounding cement to representing different quality levels of the cementing operation (low cohesion corresponds to low-quality cement and/or incomplete cementing). The simulation results show that there is very little fracturing when the cement is of high quality.. Conversely, incomplete cementing and/or weak cement can causes significant shear failure and the evolution of long fractures/cracks along the vertical well. Specifically, low cohesion between the well and cemented areas can cause significant shear failure along the well, but the same cohesion as the cemented zone does not cause shear failure. When the hydraulic fracturing pressure is high, low cohesion of the cement can causes fast propagation of shear failure and of the resulting fracture/crack, but a high-quality cement with no weak zones exhibits limited shear failure that is concentrated near the bottom of the vertical part of the well. Thus, high-quality cement and complete cementing along the vertical well appears to be the strongest protection against shear failure of the wellbore cement and, consequently, against contamination hazards to drinking water aquifers during hydraulic fracturing operations.

02 PETROLEUM↗

Mineral Deposition on the Rough Walls of a Fracture

Modeling carbonate growth in fractures and pores is important for understanding carbon sequestration in the environment or when supersaturated solutions are injected into rocks. Here, we study the simple but nontrivial problem of calcite growth on fractures with rough walls of the same mineral using kinetic Monte Carlo simulations of attachment and detachment of molecules and scaling approaches. First, we consider wedge-shaped fracture walls whose upper terraces are in the same low-energy planes and show that the valleys are slowly filled by the propagation of parallel monolayer steps in the wedge sides. The growth ceases when the walls reach these low-energy configurations so that a gap between the walls may not be filled. Second, we consider fracture walls with equally separated monolayer steps (vicinal surfaces with roughness below 1 nm) and show that growth by step propagation will eventually clog the fracture gap. In both cases, scaling approaches predict the times to attain the final configurations as a function of the initial geometry and the step-propagation velocity, which is set by the saturation index. The same reasoning applied to a random wall geometry shows that step propagation leads to lateral filling of surface valleys until the wall reaches the low-energy crystalline plane that has the smallest initial density of molecules. Thus, the final configurations of the fracture walls are much more sensitive to the crystallography than to the roughness or the local curvature. The framework developed here may be used to determine those configurations, the times to reach them, and the mass of deposited mineral. Effects of transport limitations are discussed when the fracture gap is significantly narrowed.

calcite↗

A Numerical Study of Factors Affecting Fracture-Fluid Cleanup and Produced Gas/Water in Marcellus Shale: Part II

Horizontal wells combined with successful multi-stage hydraulic fracture treatments are currently the most established method for effectively stimulating and enabling economic development of gas bearing organic-rich shale formations. Fracture cleanup in the Stimulated Reservoir Volume (SRV) is critical to stimulation effectiveness and long-term well performance. However, fluid cleanup is often hampered by formation damage, and post-fracture well performance frequently falls below expectations. A systematic study of the factors that hinder fracture fluid cleanup in shale formations can help optimize fracture treatments and better quantify long term volumes of produced water and gas. Fracture fluid cleanup is a complex process influenced by multi-phase flow through porous media (relative permeability hysteresis, capillary pressure etc.), reservoir rock and fluid properties, fracture fluid properties, proppant placement, fracture treatment parameters, and subsequent flowback and field operations. Changing SRV and fracture conductivity as production progresses further adds to the complexity of this problem. Numerical simulation is the best, and most practical approach to investigate such a complicated blend of mechanisms, parameters, their interactions, and subsequent impact on fracture fluid cleanup and well deliverability. In this paper, a 3-dimensional, 2-phase, dual-porosity model was used to investigate the impact of multiphase flow, proppant crushing, proppant diagenesis, shut-in time, reservoir rock compaction, gas slippage, and gas desorption on fracture fluid cleanup, and well performance in Marcellus shale. The research findings have shed light on the factors that substantially constrains efficient fracture fluid cleanup in gas shales, and provided guidelines for improved fracture treatment designs and water management.

58 GEOSCIENCES↗

Demonstration of CFD to support the coupled analysis of a reactor pressure vessel subjected to pressurized thermal shock

The structural components that comprise nuclear reactors and their supporting structures are subjected to harsh operating environments that can challenge their integrity, especially after exposure for extended duration or under accident condition. As one of the most significant components of a reactor, the Reactor Pressure Vessel (RPV) is exposed to an aggressive environment during the operation time (e.g. more than 40 years). Aging degradation mechanisms (e.g. thermo-fatigue) could grow initial defects up to a critical size, increasing the susceptibility to failure in the RPV. The conventional methods are mostly based on simple crack and structure geometries. Very limited studies consider the real conditions of the RPV subjected to a thermal shock due to a Loss of Coolant Accident (LOCA). During a LOCA event, the most severe conditions take place when the emergency core cooling (ECC) water is injected inside the cold legs filled initially with hotter water and/or steam. The rapid cooling of the down-comer and the internal RPV surface followed probably by re-pressurization of the RPV causes large temperature gradients and variation of pressure which induces thermal-mechanical stresses. In order to develop the model for integrity assessment of a reactor pressure vessel (RPV) subjected to pressurized thermal shock (PTS), a multi-physics simulation, which includes the thermo-hydraulic, thermo-mechanical and fracture mechanics analyses is necessary. The prediction of the temperature field is achieved by using computational fluid dynamics (CFD) simulation. In this report, a demonstration CFD standalone simulation is performed to support coupled analysis for Reactor Pressure Vessel (RPV) subjected to Pressurized Thermal Shock (PTS). The study use a simplified computational domain to represents a real RPV. The purpose of the study is to demonstrate the transient temperature response of RPV to ECC injection. The CFD model is built in a robust and efficient way for further coupled calculation. The next steps of this work, including the coupled thermal and tensor mechanics capabilities using Cardinal are expected to be complete by the end of FY21 for the demo problem. After this, into FY22, the capability will be demonstrated for a realistic RPV.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Effects of HFIR neutron irradiation on fracture toughness properties of standard and Ni-doped F82H

F82H is the Japanese reference reduced-activation ferritic-martensitic (RAFM) steel for fusion blanket applications. The harsh environment of a fusion reactor, such as neutron irradiation and He/H damage, can result in significant degradation of F82H fracture toughness. Therefore, understanding the fracture toughness behavior of F82H in the fusion environment is critical to ensure the long-term safe operation of the fusion reactor. Here, we summarize seven irradiation campaigns of the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory (ORNL) covering five variants of F82H steels, including F82H IEA, F82H Mod3, F82H doped with 1.4% natural Ni, F82H doped with 1.4% 58 Ni, and F82H doped with 1.4% 60 Ni. The irradiation temperatures covered the range from 220 °C to 530 °C and the neutron irradiation dose spanned 4 dpa to 70 dpa. The effects of neutron irradiation temperature, dose, materials composition, Ni doping, and He production on F82H fracture toughness are discussed. Our results showed that irradiation embrittlement monotonically decreased with increasing irradiation temperature until 400 °C for F82H IEA and F82H Mod3. F82H Mod3 showed better fracture toughness than F82H IEA both before and after neutron irradiation. We determined that 1.4% Ni alloying can be applied to F82H for simulating He effect in a fission reactor without jeopardizing the fracture toughness of the material. However, more studies are needed to understand the effect of high dose (>20 dpa) and He production on F82H fracture toughness.

36 MATERIALS SCIENCE↗

Validation Study of Unnotched Charpy and Taylor-Anvil Impact Experiments using Kayenta

Validation of a single computational model with multiple available strain-to-failure fracture theories is presented through experimental tests and numerical simulations of the standardized unnotched Charpy and Taylor-anvil impact tests, both run using the same material model (Kayenta). Unnotched Charpy tests are performed on rolled homogeneous armor steel. The fracture patterns using Kayenta’s various failure options that include aleatory uncertainty and scale effects are compared against the experiments. Other quantities of interest include the average value of the absorbed energy and bend angle of the specimen. Taylor-anvil impact tests are performed on Ti6Al4V titanium alloy. The impact speeds of the specimen are 321 m/s and 393 m/s. The goal of the numerical work is to reproduce the damage patterns observed in the laboratory. For the numerical study, the Johnson-Cook failure model is used as the ductile fracture criterion, and aleatory uncertainty is applied to rate-dependence parameters to explore its effect on the fracture patterns.

97 MATHEMATICS AND COMPUTING↗

Reduced-order modeling through machine learning and graph-theoretic approaches for brittle fracture applications

Typically, thousands of computationally expensive micro-scale simulations of brittle crack propagation are needed to upscale lower length scale phenomena to the macro-continuum scale. Running such a large number of crack propagation simulations presents a significant computational challenge, making reduced-order models (ROMs) attractive for this task. Here, the ultimate goal of this research is to develop ROMs that have sufficient accuracy and low computational cost so that these upscaling simulations can be readily performed. However, constructing ROMs for these complex simulations presents its own challenge. Here, we present and compare four different approaches for reduced-order modeling of brittle crack propagation in geomaterials. These methods rely on machine learning (ML) and graph-theoretic algorithms to approximate key aspects of the brittle crack problem. These methods also incorporate different physics-based assumptions in order to reduce the training requirements while maintaining accurate physics as much as possible. Results from the ROMs are directly compared against a high-fidelity model of brittle crack propagation. Further, the strengths and weaknesses of the ROMs are discussed, and we conclude that combining smart physics-informed feature engineering with highly trainable ML models provides the best performance. The ROMs considered here have computational costs that are orders-of-magnitude less than the cost associated with high-fidelity physical models while maintaining good accuracy.

36 MATERIALS SCIENCE↗

The emergence of small-scale self-affine surface roughness from deformation

Most natural and man-made surfaces appear to be rough on many length scales. There is presently no unifying theory of the origin of roughness or the self-affine nature of surface topography. One likely contributor to the formation of roughness is deformation, which underlies many processes that shape surfaces such as machining, fracture, and wear. Using molecular dynamics, we simulate the biaxial compression of single-crystal Au, the high-entropy alloy Ni 36.67 Co 30 Fe 16.67 Ti 16.67 , and amorphous Cu 50 Zr 50 and show that even surfaces of homogeneous materials develop a self-affine structure. By characterizing subsurface deformation, we connect the self-affinity of the surface to the spatial correlation of deformation events occurring within the bulk and present scaling relations for the evolution of roughness with strain. These results open routes toward interpreting and engineering roughness profiles.

42 ENGINEERING↗

HOSS: Hybrid Optimization Software Suite

HOSS software, developed at LANL, is a powerful, flexible, and parallelized package that enables the user to predict deformation and failure of materials in a variety of situations. LANL’s HOSS software is an R&D 100 finalist that integrates solid mechanics and computational fluid dynamics into a multi-physics platform able to handle millions of interacting and fracturing solids and/or particle systems. This nextgeneration simulation software integrates solid mechanics and computational fluid dynamics into a multi-physics platform able to provide state-of-the-art simulation solutions for a wide field of applications including oil and gas, construction, mining, defense, material sciences, and biomechanics.

36 MATERIALS SCIENCE↗

OpenACC directive-based GPU acceleration of an implicit reconstructed discontinuous Galerkin method for compressible flows on 3D unstructured grids

In this study, we use a combination of modeling techniques to describe the relationship between fracture radius that might be accomplished in a hypothetical enhanced geothermal system (EGS) and drilling distance required to create and access those fractures. We use a combination of commonly applied analytical solutions for heat transport in parallel fractures and 3D finite-element method models of more realistic heat extraction geometries. For a conceptual model involving multiple parallel fractures developed perpendicular to an inclined or horizontal borehole, calculations demonstrate that EGS will likely require very large fractures, of greater than 300 m radius, to keep interfracture drilling distances to ~10 km or less. As drilling distances are generally inversely proportional to the square of fracture radius, drilling costs quickly escalate as the fracture radius decreases. It is important to know, however, whether fracture spacing will be dictated by thermal or mechanical considerations, as the relationship between drilling distance and number of fractures is quite different in each case. Information about the likelihood of hydraulically creating very large fractures comes primarily from petroleum recovery industry data describing hydraulic fractures in shale. Those data suggest that fractures with radii on the order of several hundred meters may, indeed, be possible. The results of this study demonstrate that relatively simple calculations can be used to estimate primary design constraints on a system, particularly regarding the relationship between generated fracture radius and the total length of drilling needed in the fracture creation zone. Comparison of the numerical simulations of more realistic geometries than addressed in the analytical solutions suggest that simple proportionalities can readily be derived to relate a particular flow field.

15 GEOTHERMAL ENERGY↗