Search NASA⌕ Search

SEARCH · Search NASA

Results for “frequency estimation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

An experimental topographic amplification study at Los Alamos National Laboratory using ambient vibrations

An experimental study aimed at investigating potential topographic amplification of seismic waves was conducted on a 50-m-tall and 185-m-wide soft-rock ridge located at Los Alamos National Laboratory near Los Alamos, New Mexico. Ten portable broadband seismograph stations were placed in arrays across the ridge and left to record ambient vibration data for ~9 hours. Clear evidence of topographic amplification was observed by comparing spectral ratios calculated from ambient noise recordings at the toe, slope, and crest of the instrumented ridge. The inferred resonance frequency of the ridge obtained from the experimental recordings was found to agree well with several simple estimates of the theoretical resonance frequency based on its geometry and stiffness. Results support the feasibility of quantifying the frequency range of topographic amplification solely using ambient vibrations, rather than strong or weak ground motions. Additionally, comparisons have been made between a number of widely used experimental methods for quantifying topographic effects, such as the standard spectral ratio, median reference method, and horizontal-to-vertical spectral ratio. As a result, differences in the amplification and frequency range of topographic effects indicated by these methods highlight the importance of choosing a reference condition that is appropriate for the site-specific conditions and goals associated with an experimental topographic amplification study.

58 GEOSCIENCES↗

A Broadband Microwave Radiometer Technique at X-band for Rain and Drop Size Distribution Estimation

Radiometric brightess temperatures below about 12 GHz provide accurate estimates of path attenuation through precipitation and cloud water. Multiple brightness temperature measurements at X-band frequencies can be used to estimate rainfall rate and parameters of the drop size distribution once correction for cloud water attenuation is made. Employing a stratiform storm model, calculations of the brightness temperatures at 9.5, 10 and 12 GHz are used to simulate estimates of path-averaged median mass diameter, number concentration and rainfall rate. The results indicate that reasonably accurate estimates of rainfall rate and information on the drop size distribution can be derived over ocean under low to moderate wind speed conditions.

Meneghini, R.↗

Development of Simplified Probabilistic Risk Assessment Model for Seismic Initiating Event

ABSTRACT This paper discusses a simplified method to evaluate seismic risk using a methodology built on dividing the seismic intensity spectrum into multiple discrete bins. The seismic probabilistic risk assessment model uses Nuclear Regulatory Commission’s (NRC’s) full power Standardized Plant Analysis Risk (SPAR) model as the starting point for development. The seismic PRA models are integrated with their respective internal events at-power SPAR model. This is accomplished by combining the modified system fault trees from the full power SPAR model with seismic event tree logic. The peak ground acceleration is divided into five bins. The g-value for each bin is estimated using the geometric mean of lower and upper values of that particular bin and the associated frequency for each bin is estimated by taking the difference between upper and lower values of that bin. The component’s fragilities are calculated for each bin using the plant data, if available, or generic values of median peak ground acceleration and uncertainty values for the components. For human reliability analysis (HRA), the SPAR HRA (SPAR-H) method is used which requires the analysts to complete relatively straight forward worksheets that include the performance shaping factors (PSFs). The results are then used to estimate human error probabilities (HEPs) of interest. This work is expected to improve the NRC’s ability to include seismic hazards in risk assessments for operational events in support of the reactor oversight program (e.g., significance determination process).

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Resolution of Forces and Strain Measurements from an Acoustic Ground Test

The Conservatism in Typical Vibration Tests was Demonstrated: Vibration test at component level produced conservative force reactions by approximately a factor of 4 (approx.12 dB) as compared to the integrated acoustic test in 2 out of 3 axes. Reaction Forces Estimated at the Base of Equipment Using a Finite Element Based Method were Validated: FEM based estimate of interface forces may be adequate to guide development of vibration test criteria with less conservatism. Element Forces Estimated in Secondary Structure Struts were Validated: Finite element approach provided best estimate of axial strut forces in frequency range below 200 Hz where a rigid lumped mass assumption for the entire electronics box was valid. Models with enough fidelity to represent diminishing apparent mass of equipment are better suited for estimating force reactions across the frequency range. Forward Work: Demonstrate the reduction in conservatism provided by; Current force limited approach and an FEM guided approach. Validate proposed CMS approach to estimate coupled response from uncoupled system characteristics for vibroacoustics.

Smith, Andrew M.↗

New Evidence for a Coronal Mass Ejection-driven High Frequency Type II Burst near the Sun

We report observations of the high frequency type II radio burst (≈430–30 MHz) that occurred in the solar corona on 2015 November 4. The drift rate of the burst, estimated close to the start frequency of its fundamental component (≈215 MHz), is unusually high (≈2 MHz s{sup −1}). Our analysis shows that the estimated speed of the magnetohydrodynamic shock driver of the burst varies with time. The peak speed and acceleration are very large, ≈2450 km s{sup −1} and ≈17 km s{sup −2}, respectively. There is spatio-temporal correlation between the type II burst and the associated coronal mass ejection (CME) in the whitelight and extreme-ultraviolet images. The time profile of the shock speed and the light curve of the associated soft X-ray flare correlate well. These results indicate that in the present case, (i) the magnetohydrodynamic shock responsible for the high frequency coronal type II burst is driven by the CME and (ii) the time profile of the type II burst shock speed represents the near-Sun kinematics of the CME.

79 ASTRONOMY AND ASTROPHYSICS↗

Multi-Agent Simulation Based Framework for Power Restoration Time Estimation at Distribution Level

The growing frequency of power outages has prompted increased interest in developing a more resilient power grid that can quickly recover from weather-related damage. At the distribution level, power restoration is a complex, multi-stage process involving multiple response entities. Providing utility stakeholders, government regulators, and the public with information about outage duration and estimated time to restoration is crucial. The research employs a multi-agent simulation approach, which allows for the simulation of decision-making behaviors among different entities and the incorporation of various uncertainties. Specifically, the study uses the open-source simulation package Mesa-Geo in conjunction with the Python language and constructs a road network using the open-source network extension pgRouting for routing queries. The research design includes several experiments focused on Florida as a case study, comparing repair crew sizes, power outage numbers, and road damage scenarios. The findings could offer valuable managerial guidance on resource allocation in the restoration process.

Chen, Yang↗

Development of an on-line parameter estimation system using the discrete modal filter

Ongoing development of an automated system for monitoring the frequency and damping of time varying structural systems is discussed. A spatial filtering technique called the discrete modal filter is used to uncouple multiple response measurements into modal coordinate responses. Since the modal coordinate responses are the responses of single-degree-of-freedom systems, the frequency and damping may be accurately estimated with short data records. An on-line monitoring system is discussed which may be useful in a variety of applications. The focus in this paper is on the application to aircraft flight flutter testing.

Shelley, S. J.↗

Frequency synchronization of a frequency-hopped MFSK communication system

This paper presents the performance of fine-frequency synchronization. The performance degradation due to imperfect frequency synchronization is found in terms of the effect on bit error probability as a function of full-band or partial-band noise jamming levels and of the number of frequency hops used in the estimator. The effect of imperfect fine-time synchronization is also included in the calculation of fine-frequency synchronization performance to obtain the overall performance degradation due to synchronization errors.

Huth, G. K.↗

Pasteurization of shell eggs using radio frequency heating

The USDA-FSIS estimates that pasteurization of all shell eggs in the U.S. would reduce the annual number of illnesses by more than 110,000. However, less than 3% of shell eggs are commercially pasteurized. One of the main reasons for this is that the commercial hot water process requires as much as 60 min to complete. In the present study, a radio frequency (RF) apparatus was constructed, and a two-step process was developed that uses RF energy and hot water, to pasteurize eggs in less than half the time. In order to select an appropriate RF generator, the impedance of shell eggs was measured in the frequency range of 10–70 MHz. The power density within the egg was modeled to prevent potential hotspots. Escherichia coli (ATCC 35218) was inoculated in the yolk to approximately 7.5 log CFU/ml. The combination process first heated the egg in 35.0 °C water for 3.5 min using 60 MHz RF energy. This resulted in the yolk being preferentially heated to 61 °C. Then, the egg was heated for an additional 20 min with 56.7 °C water. This two-step process reduced the population of E. coli by 6.5 log. The total time for the process was 23.5 min. By contrast, processing for 60 min was required to reduce the E. coli by 6.6 log using just hot water. The novel RF pasteurization process presented in this study was considerably faster than the existing commercial process. As a result, this should lead to an increase in the percentage of eggs being pasteurized, as well as a reduction of foodborne illnesses.

42 ENGINEERING↗

Data Analytics for Electrical Distribution Systems with Micro PMUs (GMLC 1.4.9 Technical Report)

This report describes how electrical utilities with residential, industrial, commercial and government customers make decisions using Data Analytics (DA) applications and discusses how OpenFMB was leveraged to share that data among disparate types of devices for DA. OpenFMB is a data standard developed by utilities for distributed communication and control of power system assets. Here we explored how OpenFMB can be used for sharing analytics and what those analytics could be for a set of representative grid devices. A review of DA applications performed by electrical utilities and customers is presented. An overview of how the testbed we used was built and configured is summarized. Several experiments which were carried out to explore the capabilities of OpenFMB alongside other data sharing mechanisms for gathering sensor measurements and sharing analytics is also discussed. And finally a comparison of OpenFMB and LBNL’s SPARK framework is summarized. Today’s electrical utilities focus on monitoring the real-time customer consumptions, offering new real-time tariff models based on customer usage habits (rewards and punishments), providing energy peak during peak load times (plan energy generation and distribution), improving the load management for transformers and power lines, and controlling the energy and grid resources efficiently. On the other hand, the DA applications for residential customers are based on modifying the customer electricity usage habit to save money, making accurate and timely decisions for electrical billing. However, the DA applications for industrial, commercial and government customers focus on creating efficient programs to improve the environmental condition (reducing CO₂ emission), developing better load forecasting for industrial and/or commercial activities. In this project, a testbed was built to explore how the OpenFMB framework can be used to distribute data among various types of representative grid edge devices. Micro PMUs (Phasor Measurement Unit) were used to collect and transmit data to an OpenPDC server alongside relays with a framework configured with a system using OpenFMB to collect and transmit data. The testbed was composed of a physical asset based on a 60 Hz AC radial power system constructed using SI-GRID components. The power system consisted of a 3-phase 14 volts line-to-ground (24 volts line-to-line) power source, three 3-phase line emulators, a programmable resistive load bank, two smart relays, two micro PMUs, and a (SCADA) and Phasor Data Concentrator (PDC) computer. This testbed configuration allowed us to perform breaker operation tests collecting data from the micro PMUs and from the relays’ sensors. During the micro PMU breaker operation tests we collected the measured and estimated fundamental voltages, currents, frequency as well as the total true, reactive and apparent power. The displacement power factor from two micro PMUs located in parallel power lines was also used. The software steps for the implementation of the Synchrophasor system are explained in detail in this report. The setting (1-2-3) and data collection (4-5) phases were performed with a free download open source software. In the setting phase, the micro PMUs were set (1), the data stream for each micro PMU was validated, and the connection and configuration files were created (2). The PDC computer was set using the connection and configuration files of the micro PMUs (3). In the data collection phase, the binary data from the micro PMUs was collected (4), and the binary data files of the micro PMUs was converted to analyze the test results (5). OpenFMB was configured to use protocol translators to read Modbus and transform the reading into the OpenFMB data model to be read for DA applications.Our experiments showed that by leveraging the OpenFMB data model and the micro PMUs together we could obtain better situational awareness of network faults, which in some cases could lead to failures in the system and would be less perceivable otherwise. For example, in one experiment the fundamental RMS current angle, and the fundamental displacement power factor (estimated by the ratio between the measured real and apparent total power) had a disturbance at the micro PMU connected to the beginning of the parallel power line because the breaker was opened without the operators or SCADA system’s knowledge, and no current was available. Based on the breaker state scenarios and micro PMU locations, the DA applications using the current angle and displacement power factor from the micro PMUs should be studied in detail to avoid a non-desired measurement that could affect the decision from the DA. Also, the sample rates for PMU, Relay and micro PMU devices were compared. The DA application improved the control and operation between the electrical utilities and their customers (residential, industrial, transportation, commercial and government). The higher the sample rate, the better the quality of the measurement for DA estimations.

42 ENGINEERING↗

Proactive Frequency Stability Scheme: A Distributed Framework Based on Particle Filters and Synchrophasors

The reactive nature of traditional under-frequency load shedding schemes can lead to delayed response and unnecessary loss of load. This work presents a proactive framework for power system frequency stability. Bayesian filters and synchrophasors are leveraged to produce predictions after disturbances are detected. By being able to estimate the future state of frequency corrective actions can be taken before the system reaches a critical condition. This proactive approach makes it possible to optimize the response to a disturbance, which results in a decrease in the amount of compensation utilized. The framework is tested via Matlab simulations based on Kundur’s Two-Area System, and the IEEE 14-Bus System. Performance metrics are provided and evaluated against other contemporary solutions found in literature. During testing this framework outperformed other solutions by drastically reducing the amount of load dropped during compensation.

42 ENGINEERING↗

PFLOTRAN-SIP: A PFLOTRAN Module for Simulating Spectral-Induced Polarization of Electrical Impedance Data

Spectral induced polarization (SIP) is a non-intrusive geophysical method that collects chargeability information (the ability of a material to retain charge) in the time domain or its phase shift in the frequency domain. Although SIP is a temporal method, it cannot measure the dynamics of flow and solute/species transport in the subsurface over long times (i.e., 10–100 s of years). Data collected with the SIP technique need to be coupled with fluid flow and reactive-transport models in order to capture long-term dynamics. To address this challenge, PFLOTRAN-SIP was built to couple SIP data to fluid flow and solute transport processes. Specifically, this framework couples the subsurface flow and transport simulator PFLOTRAN and geoelectrical simulator E4D without sacrificing computational performance. PFLOTRAN solves the coupled flow and solute-transport process models in order to estimate solute concentrations, which were used in Archie’s model to compute bulk electrical conductivities at near-zero frequency. These bulk electrical conductivities were modified while using the Cole–Cole model to account for frequency dependence. Using the estimated frequency-dependent bulk conductivities, E4D simulated the real and complex electrical potential signals for selected frequencies for SIP. These frequency-dependent bulk conductivities contain information that is relevant to geochemical changes in the system. This study demonstrated that the PFLOTRAN-SIP framework is able to detect the presence of a tracer in the subsurface. SIP offers a significant benefit over ERT in the form of greater information content. It provided multiple datasets at different frequencies that better constrained the tracer distribution in the subsurface. Consequently, this framework allows for practitioners of environmental hydrogeophysics and biogeophysics to monitor the subsurface with improved resolution.

54 ENVIRONMENTAL SCIENCES↗

Quasilinear Relaxation as a Mechanism for Electron Temperature Saturation in the Earth’s Plasmasphere

A mechanism is presented according to which quasi-linear relaxation can cause electron temperature saturation at the observed level when the plasmasphere is heated by magnetohydrodynamic waves. An algorithm for calculating saturation temperatures is proposed, and they are numerically estimated. At low wave frequencies, saturation occurs at temperatures of 3–5 eV, and in the vicinity of cyclotron frequencies, it occurs at 2–4 eV.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Analyzing historical snow trends in interior Alaska

Study region The Chena River watershed in Interior Alaska, USA Study focus This study examines 40 years (water years 1982–2021) of snowpack characteristics to consider its hydrological implications in the 5350 km² Chena River basin. Using observations and a fine-scale physics model, we analyzed trends of snow water equivalent (SWE), snow onset and disappearance, and snow cover duration (SCD). New hydrological insights for the region Results indicate a decline in SWE across the modeled domain, averaging a decrease of 3 mm per decade, with larger decreases (up to 10 mm per decade) at lower elevations. While domain-averaged SWE trends were not statistically significant, observed SCD showed statistically significant decreases: −5.2, −5.0, and −4.4 days per decade at Teuchet Creek, Fairbanks F.O., and Little Chena Ridge, respectively. Notably, observations at SNOTEL stations and modeling revealed no statistically significant change in domain-averaged Rain-on-Snow (ROS) events over the 40-year period, contrasting some regional future estimates of increased ROS frequency. Peak streamflow did not consistently correlate with peak SWE levels, suggesting that other environmental factors such as ROS events and rapid temperature increases (e.g., a 10°C spike observed in 1992) are key drivers of hydrological outcomes. These findings improve understanding of complex subarctic hydrological processes impacting permafrost and highlight the need for adaptive water resource management to mitigate multi-factor risks like flooding and wildfire, requiring proactive planning.

54 ENVIRONMENTAL SCIENCES↗

Risk assessment based on urinary bisphenol A levels in the general Korean population

Bisphenol A (BPA) is a high-volume industrial chemical used in the global production of polycarbonate plastics and epoxy resins, which are used in food and drink containers, such as tableware (plates and mugs). Due to its broad applications, BPA has been detected in human blood, urine and breast milk as well as environmental substances, including water, indoor and outdoor air, and dust. Indeed, exposure to high concentrations of BPA can result in a variety of harmful effects, including reproductive toxicity, through a mechanism of endocrine disruption. Our comparison of reported BPA urinary concentrations among different countries revealed that exposures in Korea may be higher than those in other Asian countries and North America, but lower than or similar to those in European countries. The current study included a total of 2044 eligible subjects of all ages. The subjects were evenly divided between males and females (48.58% and 51.42%, respectively). The geometric mean (GM) of pre-adjusted (adjusted) urinary BPA concentrations was 1.83 μg/L (2.01 μg/g creatinine) for subjects of all ages, and there was no statistically difference in BPA concentrations between males (1.90 μg/L, 1.87 μg/g creatinine) and females (1.76 μg/L, 2.16 μg/g creatinine). Multiple regression analysis revealed only one positive association between creatinine pre-adjusted urinary BPA concentration and age (β=−0.0868, p<0.001). The 95th percentile levels of 24-hour recall (HR), food frequency questionnaires (FFQ) and estimated daily intake (EDI) through urinary BPA concentrations were 0.14, 0.13, and 0.22 μg/kg bw/day, respectively. According to the Ministry of Food and Drug Safety (MFDS), a tolerable daily intake (tDI) of 20 μg/kg bw/day was established for BPA from the available toxicological data. Recently, the European Food Safety Authority (EFSA) established a temporary TDI of 4 μg/kg bw/day based on current toxicological data. By comparing these TDIs with subjects' exposure, we conclude that there are no health concerns for any age group as a result of current levels of dietary exposure to BPA. - Highlights: • We compared urinary bisphenol A (BPA) levels among different countries. • We evaluated the urinary BPA levels of the general Korean population. • We found that the overall GM of urinary BPA concentration was 1.83 μg/L. • We derived a TDI of 20 μg/kg bw/day for BPA. • There is no health concern for any age group from current levels of exposure to BPA.

54 ENVIRONMENTAL SCIENCES↗

Nodal Clearance Rate and Long-Term Efficacy of Individualized Sentinel Node–Based Pelvic Intensity Modulated Radiation Therapy for High-Risk Prostate Cancer

Purpose: To assess the efficacy of individual sentinel node (SN)-guided pelvic intensity modulated radiation therapy (IMRT) by determining nodal clearance rate [(n expected nodal involvement − n observed regional recurrences)/n expected nodal involvement] in comparison with surgically staged patients. Methods and Materials: Data on 475 high-risk prostate cancer patients were examined. Sixty-one consecutive patients received pelvic SN-based IMRT (5 × 1.8 Gy/wk to 50.4 Gy [pelvic nodes + individual SN] and an integrated boost with 5 × 2.0 Gy/wk to 70.0 Gy to prostate + [base of] seminal vesicles) and neo-/adjuvant long-term androgen deprivation therapy; 414 patients after SN–pelvic lymph node dissection were used to calculate the expected nodal involvement rate for the radiation therapy sample. Biochemical control and overall survival were estimated for the SN-IMRT patients using the Kaplan-Meier method. The expected frequency of nodal involvement in the radiation therapy group was estimated by imputing frequencies of node-positive patients in the surgical sample to the pattern of Gleason, prostate-specific antigen, and T category in the radiation therapy sample. Results: After a median follow-up of 61 months, 5-year OS after SN-guided IMRT reached 84.4%. Biochemical control according to the Phoenix definition was 73.8%. The nodal clearance rate of SN-IMRT reached 94%. Retrospective follow-up evaluation is the main limitation. Conclusions: Radiation treatment of pelvic nodes individualized by inclusion of SNs is an effective regional treatment modality in high-risk prostate cancer patients. The pattern of relapse indicates that the SN-based target volume concept correctly covers individual pelvic nodes. Thus, this SN-based approach justifies further evaluation, including current dose-escalation strategies to the prostate in a larger prospective series.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Structural characterization, thermoluminescence and EPR studies of Nd{sub 2}O{sub 3}:Co{sup 2+} nanophosphors

Graphical abstract: Display Omitted Highlights: ► Nd{sub 2}O{sub 3}:Co{sup 2+} (1–4 mol%) nanophosphors have been prepared at much lower temperatures. ► Phosphors are well characterized by PXRD, SEM, TEM, FTIR, Raman, UV–vis spectroscopy. ► EPR and thermoluminescence properties were also reported. ► TL intensity increases linearly with γ dose suggesting usage in radiation dosimetry. -- Abstract: Nd{sub 2}O{sub 3}:Co{sup 2+} (1–4 mol%) nanophosphors (15–25 nm) have been prepared via low temperature solution combustion method. Scanning electron micrograph (SEM) shows that the product is highly porous in nature. The stokes line in the Raman spectrum at ∼2000 cm{sup −1} is assigned to F{sub g} mode and the anti-stokes lines are assigned to a combination of A{sub g} + E{sub g} modes. With increase of Co{sup 2+} concentration, the intensity of F{sub g} mode decreases, whereas the combination of A{sub g} + F{sub g} modes completely disappears. Electron paramagnetic resonance (EPR) spectrum exhibits two resonance signals with effective g values at g = 2.25 and g = 2.03. Thermoluminescence (TL) response of Nd{sub 2}O{sub 3}:Co{sup 2+} nanopowders with γ dose 0.23–2.05 kGy was studied. The activation energy (E) and frequency factor (s) are estimated using Chen's glow peak shape method and obtained to be in the range 0.45–1.67 eV and 1.8 × 10{sup 4} to 4.0 × 10{sup 12} s{sup −1}, respectively. It is observed that the TL glow peak intensity at 430 K increases linearly with γ dose which is suitable for radiation dosimetry.

36 MATERIALS SCIENCE↗

Laser Doppler vibrometry for piezoelectric coefficient ($d_{33}$) measurements in irradiated aluminum nitride

Sensors used for experiments in advanced reactors must survive in harsh environments. Few material systems can be used to construct sensors viable for extreme conditions. Aluminum nitride (AlN) is one such material because it has high thermal stability and radiation resistance and sustains good piezoelectric and dielectric properties at high temperatures. In this work, the piezoelectric coefficient $d_{33}$ of the AlN single-crystal with thermal and irradiation damage was investigated using an indirect method with a laser Doppler vibrometer (LDV). Surface electrodes were deposited on the AlN samples, and the vibration response of the samples to an applied voltage was monitored using the LDV as a function of the excitation frequency. The $d_{33}$ estimation was based on the excitation voltage and the thickness-mode displacement extracted from the LDV measurements. Further, six AlN substrates were irradiated with 8 MeV Al 2+ at three fluences (10 15 , 10 16 , and 10 17 ions/cm 2 ) and two temperatures (300 °C and 500 °C). The $d_{33}$ for the six irradiated samples and one pristine sample were measured, and the measurement uncertainty was estimated based on five repeated tests. All samples were also measured by a commercial piezometer for comparison. The experimental results demonstrate that the piezoelectric coefficients obtained by LDV were about 0.8–1.16 pm/V lower than those obtained by the piezometer. With the compensation of the clamping effect, the corrected LDV values are similar to the piezometer results. Both show similar trends in all samples, which validates the feasibility of the proposed method for $d_{33}$ measurement. Based on the LDV results, the irradiated samples show a 12%–22% decrease in $d_{33}$ compared with the pristine samples. The samples irradiated under the same fluence at a higher temperature (500 °C) demonstrated a lower $d_{33}$ than those at 300 °C. The effect of the retro-reflective tape, sample temperature, and sample size on the $d_{33}$ measurement were also studied.

36 MATERIALS SCIENCE↗