Search NASA⌕ Search

SEARCH · Search NASA

Results for “friction experiments”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

Mechanical specific energy versus depth of cut in rock cutting and drilling

The relationship between Mechanical Specific Energy (MSE) and the Rate of Penetration (ROP), or equivalently the depth of cut per revolution, provides an important measure for strategizing a drilling operation. This study explores how MSE evolves with depth of cut, and presents a concerted effort that encompasses analytical, computational and experimental approaches. A simple model for the relationship between MSE and cutting depth is first derived with consideration of the wear progression of a circular cutter. This is an extension of Detournay and Defourny's phenomenological cutting model. Wear is modeled as a flat contact area at the bottom of a cutter referred to as a wear flat, and that wear flat in the past is often considered to be fixed during cutting. But during a drilling operation by a full bit that consists of multiple circular cutters, the wear flat length may increase because of various wear mechanisms involved. The wear progression of cutters generally results in reduced efficiency with either increased MSE or decreased ROP. Also, an accurate estimate of removed rock volume is found important for the evaluation of MSE. The derived model is compared with experiment results from a single circular cutter, for cutting soft rock under ambient pressure with actual depth measured through a micrometer, and for cutting high strength rock under high pressure with actual cutting area measured by a confocal microscope. Lastly, the model is employed to interpret the evolution of MSE with depth of cut for a full drilling bit under confining pressure. The general form of equation of the developed model is found to describe well the experiment data and can be applied to interpret the drilling data for a full bit.

42 ENGINEERING↗

Laminar-Turbulent Transition Upstream of the Entropy-Layer Swallowing Location in Hypersonic Boundary Layers

Numerical and experimental studies have demonstrated that modal growth of planar Mack modes is responsible for laminar-turbulent transition on sharp cones at hypersonic speeds. However, the physical mechanisms that lead to transition onset upstream of the entropy-layer swallowing location over sufficiently blunt geometries are not well understood as yet. Modal amplification is too weak or nonexistent to initiate transition at moderate-to-large bluntness values. Nonmodal analysis shows that, with increasing nose bluntness, both planar and oblique traveling disturbances that peak within the entropy layer experience appreciable energy amplification. However, because of the relatively weak signature of the nonmodal traveling disturbances within the boundary-layer region, the route to transition onset subsequent to the nonmodal growth remains unclear. Thus, nonlinear parabolized stability equations (NPSE) and direct numerical simulations (DNS) have been used to investigate the potential transition mechanisms over a 7-degree blunt cone that was tested in the AFRL Mach-6 high-Reynoldsnumber facility. Computations are performed to separately follow the nonlinear development of two classes of inflow disturbances, namely, a pair of oblique traveling waves with equal but opposite angles with respect to the mean flow direction and a planar traveling wave. Results in both cases show an excellent agreement between the NPSE and DNS predictions, establishing that the NPSE is an accurate and efficient technique for predicting the nonlinear development for these particular nonmodal traveling disturbances. Computations reveal that the oblique mode interactions lead to the generation of stationary streaks inside the boundary layer that, in turn, facilitate the growth of a subharmonic sinuous disturbance. For relatively modest amplitudes of the inflow disturbance, the oblique-mode breakdown can lead to transition at the measured location of transition onset during the experiment. On the other hand, the nonlinear development of a planar traveling wave leads to the formation of inclined structures just above the boundary-layer edge and these structures are strongly reminiscent of the transitional events observed during blunt cone experiments by using schlieren flow visualizations.

Entropy↗

Numerical investigation of turbulence models for shock separated boundary-layer flows

Numerical solutions of the Navier-Stokes equations for shock separated turbulent boundary-layer flows are presented. Several turbulence models are investigated and assessed by their ability to predict the physical phenomena associated with two extensively documented experiments. The experimental flows consist of shock-wave boundary-layer interactions in axisymmetric internal and external geometries at Mach numbers of 1.5 and 7, respectively. Algebraic and one-equation eddy viscosity models are used to describe the Reynolds shear stress. Calculated values of skin friction, wall pressure distribution, kinetic energy of turbulence, and heat transfer are compared with measurements.

Viegas, J. R.↗

Ozone budgets from the Dynamics and Chemistry of Marine Stratocumulus experiment

Measurements from the Dynamics and Chemistry of marine Stratocumulus experiment have been used to study components of the regional ozone budget. The surface destruction rate is determined by eddy correlation of ozone and vertical velocity measured by a low-flying aircraft. Significant variability is found in the measured surface resistance; it is partially correlated with friction velocity but appears to have other controlling influences as well. The mean resistance is 4190 s/m which is higher (slower destruction) than most previous estimates for seawater. Flux and mean measurements throughout the marine boundary layer are used to estimate the net rate of in situ photochemical production/destruction of ozone. Averaged over the flights, ozone concentration is found to be near steady state, and a net of photochemical destruction of 0.02-0.07 ng/cu m per sec is diagnosed. This is an important confirmation of photochemical model results for the remote marine boundary layer. Ozone vertical distributions above the boundary layer show a strongly layered structure with very sharp gradients. These distributions are possibly related to the stratospheric ozone source.

Kawa, S. R.↗

Prediction of Fretting Crack Location and Orientation in a Single Crystal Nickel Alloy

Fretting is a structural damage mechanism arising between two nominally clamped surfaces subjected to an oscillatory loading. A critical location for fretting induced damage has been identified at the blade/disk and blade/damper interfaces of gas turbine engine turbomachinery and space propulsion components. The high- temperature, high-frequency loading environment seen by these components lead to severe stress gradients at the edge-of-contact that could potentially foster crack growth leading to component failure. These contact stresses drive crack nucleation in fretting and are very sensitive to the geometry of the contacting bodies, the contact loads, materials, temperature, and contact surface tribology (friction). Recently, a high-frequency, high-temperature load frame has been designed for experimentally investigating fretting damage of single crystal nickel materials employed in aircraft and spacecraft turbomachinery. A modeling method for characterizing the fretting stresses of the spherical fretting contact stress behavior in this experiment is developed and described. The calculated fretting stresses for a series of experiments are then correlated to the observed fretting damage. Results show that knowledge of the normal stresses and resolved shear stresses on each crystal plane can aid in predicting crack locations and orientations.

Matlik, J. F.↗

Mechanical and tribological property comparison of melt-compounded nanocomposites of atomic-layer-deposition-coated polyamide particles and commercial nanofillers

Mechanical and tribological properties of melt-compounded titanium dioxide nanocomposites of atomic-layer-deposition (ALD)-coated polyamide particles and commercial nanofillers were compared. The nanofiller dispersion in the polyamide matrix was studied using transmission electron microscopy showing very different morphology for the ALD-created and the traditional nanocomposites: former appearing as ribbons in the matrix whereas latter composing from spherical clusters. The effect of such morphology change on the specimen's mechanical response subjected to tensile and impact loading was investigated. The results demonstrated that ALD-created nanocomposites possess significantly higher Young's modulus than pure and traditionally filled polyamide matrix. However, transition from ductile to brittle behavior occurs especially for the ALD-created nanocomposites. Notched impact strength experiments supported this, suggesting that the impact strength of ALD-created composites decreased significantly compared to pure polyamide matrix, whereas traditionally melt-compounded nanocomposites showed no significant changes. Furthermore, the tribological properties of the selected specimens were determined and the effect of the nanofiller on the friction and scratching properties of the polyamide matrix is discussed.

36 MATERIALS SCIENCE↗

Mechanisms Leading to Co-Existence of Gas Hydrate in Ocean Sediments [Part 1 of 2]

In this project we have sought to explain the co-existence of gas and hydrate phases in sediments within the gas hydrate stability zone. We have focused on the gas/brine interface at the scale of individual grains in the sediment. The capillary forces associated with a gas/brine interface play a dominant role in many processes that occur in the pores of sediments and sedimentary rocks. The mechanical forces associated with the same interface can lead to fracture initiation and propagation in hydrate-bearing sediments. Thus the unifying theme of the research reported here is that pore scale phenomena are key to understanding large scale phenomena in hydrate-bearing sediments whenever a free gas phase is present. Our analysis of pore-scale phenomena in this project has delineated three regimes that govern processes in which the gas phase pressure is increasing: fracturing, capillary fingering and viscous fingering. These regimes are characterized by different morphology of the region invaded by the gas. On the other hand when the gas phase pressure is decreasing, the corresponding regimes are capillary fingering and compaction. In this project, we studied all these regimes except compaction. Many processes of interest in hydrate-bearing sediments can be better understood when placed in the context of the appropriate regime. For example, hydrate formation in sub-permafrost sediments falls in the capillary fingering regime, whereas gas invasion into ocean sediments is likely to fall into the fracturing regime. Our research provides insight into the mechanisms by which gas reservoirs are converted to hydrate as the base of the gas hydrate stability zone descends through the reservoir. If the reservoir was no longer being charged, then variation in grain size distribution within the reservoir explain hydrate saturation profiles such as that at Mt. Elbert, where sand-rich intervals containing little hydrate are interspersed between intervals containing large hydrate saturations. Large volumes (of order one pore volume) of gaseous and aqueous phases must be transported into the gas hydrate stability zone. The driver for this transport is the pressure sink induced by a reduction in occupied pore volume that accompanies the formation of hydrate from gas and water. Pore-scale imbibition models and bed-scale multiphase flow models indicate that the rate-limiting step in converting gas to hydrate is the supply of water to the hydrate stability zone. Moreover, the water supply rate is controlled by capillarity-driven flux for conditions typical of the Alaska North Slope. A meter-scale laboratory experiment confirms that significant volumes of fluid phases move into the hydrate stability zone and that capillarity is essential for the water flux. The model shows that without capillarity-driven flux, large saturations of hydrate cannot form. The observations of thick zones of large saturation at Mallik and Mt Elbert thus suggest that the primary control on these systems is the rate of transport of gaseous and aqueous phases, driven by the pressure sink at the base of the gas hydrate stability zone. A key finding of our project is the elucidation of "capillary fracturing" as a dominant gas transport mechanism in low-permeability media. We initially investigate this phenomenon by means of grain-scale simulations in which we extended a discrete element mechanics code (PFC, by Itasca) to incorporate the dynamics of first single-phase and then multiphase flow. A reductionist model on a square lattice allows us to determine some of the fundamental dependencies of the mode of gas invasion (capillary fingering, viscous fingering, and fracturing) on the parameters of the system. We then show that the morphology of the gas-invaded region exerts a fundamental control on the fabric of methane hydrate formation, and on the overpressures caused by methane hydrate dissociation. We demonstrate the existence of the different invasion regimes by means of controlled laboratory experiments in a radial cell. We collapse the behavior in the form of a phase diagram fully characterized by two dimensionless groups: a modified capillary number and a "fracturing number" that reflects the balance between the pressure forces that act to open conduits in the granular pack, and frictional forces that resist it. We use all this small-scale knowledge to propose simple mechanistic models of gas migration and hydrate formation at the geologic bed scale. We propose that methane transport in lake and oceanic sediments is controlled by dynamic conduits, which dilate and release gas as the falling hydrostatic pressure reduces the effective stress below the tensile strength of the sediments. We test our model against a four-month record of hydrostatic load and methane flux in Upper Mystic Lake, Mass., USA, and show that it captures the complex episodicity of methane ebullition. Our quantitative conceptualization opens the door to integrated modeling of methane transport to constrain global methane release from lakes and other methane-rich sediment systems, and to assess its climate feedbacks.

58 GEOSCIENCES↗

Mechanisms Leading to Co-Existence of Gas Hydrate in Ocean Sediments [Part 2 of 2]

In this project we have sought to explain the co-existence of gas and hydrate phases in sediments within the gas hydrate stability zone. We have focused on the gas/brine interface at the scale of individual grains in the sediment. The capillary forces associated with a gas/brine interface play a dominant role in many processes that occur in the pores of sediments and sedimentary rocks. The mechanical forces associated with the same interface can lead to fracture initiation and propagation in hydrate-bearing sediments. Thus the unifying theme of the research reported here is that pore scale phenomena are key to understanding large scale phenomena in hydrate-bearing sediments whenever a free gas phase is present. Our analysis of pore-scale phenomena in this project has delineated three regimes that govern processes in which the gas phase pressure is increasing: fracturing, capillary fingering and viscous fingering. These regimes are characterized by different morphology of the region invaded by the gas. On the other hand when the gas phase pressure is decreasing, the corresponding regimes are capillary fingering and compaction. In this project, we studied all these regimes except compaction. Many processes of interest in hydrate-bearing sediments can be better understood when placed in the context of the appropriate regime. For example, hydrate formation in sub-permafrost sediments falls in the capillary fingering regime, whereas gas invasion into ocean sediments is likely to fall into the fracturing regime. Our research provides insight into the mechanisms by which gas reservoirs are converted to hydrate as the base of the gas hydrate stability zone descends through the reservoir. If the reservoir was no longer being charged, then variation in grain size distribution within the reservoir explain hydrate saturation profiles such as that at Mt. Elbert, where sand-rich intervals containing little hydrate are interspersed between intervals containing large hydrate saturations. Large volumes (of order one pore volume) of gaseous and aqueous phases must be transported into the gas hydrate stability zone. The driver for this transport is the pressure sink induced by a reduction in occupied pore volume that accompanies the formation of hydrate from gas and water. Pore-scale imbibition models and bed-scale multiphase flow models indicate that the rate-limiting step in converting gas to hydrate is the supply of water to the hydrate stability zone. Moreover, the water supply rate is controlled by capillarity-driven flux for conditions typical of the Alaska North Slope. A meter-scale laboratory experiment confirms that significant volumes of fluid phases move into the hydrate stability zone and that capillarity is essential for the water flux. The model shows that without capillarity-driven flux, large saturations of hydrate cannot form. The observations of thick zones of large saturation at Mallik and Mt Elbert thus suggest that the primary control on these systems is the rate of transport of gaseous and aqueous phases, driven by the pressure sink at the base of the gas hydrate stability zone. A key finding of our project is the elucidation of ?capillary fracturing? as a dominant gas transport mechanism in low-permeability media. We initially investigate this phenomenon by means of grain-scale simulations in which we extended a discrete element mechanics code (PFC, by Itasca) to incorporate the dynamics of first singlephase and then multiphase flow. A reductionist model on a square lattice allows us to determine some of the fundamental dependencies of the mode of gas invasion (capillary fingering, viscous fingering, and fracturing) on the parameters of the system. We then show that the morphology of the gas-invaded region exerts a fundamental control on the fabric of methane hydrate formation, and on the overpressures caused by methane hydrate dissociation. We demonstrate the existence of the different invasion regimes by means of controlled laboratory experiments in a radial cell. We collapse the behavior in the form of a phase diagram fully characterized by two dimensionless groups: a modified capillary number and a ?fracturing number? that reflects the balance between the pressure forces that act to open conduits in the granular pack, and frictional forces that resist it. We use all this small-scale knowledge to propose simple mechanistic models of gas migration and hydrate formation at the geologic bed scale. We propose that methane transport in lake and oceanic sediments is controlled by dynamic conduits, which dilate and release gas as the falling hydrostatic pressure reduces the effective stress below the tensile strength of the sediments. We test our model against a four-month record of hydrostatic load and methane flux in Upper Mystic Lake, Mass., USA, and show that it captures the complex episodicity of methane ebullition. Our quantitative conceptualization opens the door to integrated modeling of methane transport to constrain global methane release from lakes and other methane-rich sediment systems, and to assess its climate feedbacks.

58 GEOSCIENCES↗

Shock compaction of molybdenum powder

Shock recovery experiments which were carried out in the 9 to 12 GPa range on 1.4 distension Mo and appear adequate to compact to full density ( 45 (SIGMA)m) powders were examined. The stress levels, however, are below those calculated to be from 100 to approx. 22 GPa which a frictional heating model predicts are required to consolidate approx. 10 to 50 (SIGMA)m particles. The model predicts that powders that have a distension of m=1.6 shock pressures of 14 to 72 GPa are required to consolidate Mo powders in the 50 to 10 (SIGMA)m range.

Ahrens, T. J.↗

Design, Fabrication and Testing of an Experimental Apparatus for Determining Particle Behavior Under Very Low Intergranular Stresses

Because the constitutive laws for soils are governed mainly by interparticle friction, all aspects of their mechanical behavior depend strongly on gravitational body forces. This fact poses serious limitations on the formulation of a materially objective soil constitutive theory, based on experimentation performed on Earth. In particular, the presence of the Earth's gravity prohibits the design of controlled experiments to properly simulate a variety of critical phenomena associated with the dynamic response of soils to seismic excitation in a very low effective confining stress field. For these reasons, laboratory-controlled experiments in the Space Shuttle, under essentially zero-gravity conditions, could offer invaluable opportunities for developing a quantitative understanding of fundamental aspects of soil behavior during or after an earthquake, which, in turn, could result in significant technological advances in geotechnical earthquake engineering.

Sture, S.↗

Lab tests of a thermomechanical pump for shoot

Laboratory tests of a thermomechanical (TM) pump utilizing a commercially available porous disk have been conducted. Various size disks, heater configurations, and outlet flow impedances have been used to characterize scale models of the pump proposed for the Superfluid Helium On-Orbit Transfer (SHOOT) Flight Experiment. The results yield the scalability of the TM pump to larger diameters, and hence larger pumping rates, the dependence of flow rate on back pressure and heater power, and the limits of pumping speed due to internal losses within the porous disk due to mutual and superfluid friction. Analysis indicates that for low back pressures the flow rate is limited by the superfluid friction rather than the mutual friction. For the porous plug used in the early tests this amounts to a practical limit of 4.4 liters per hour per square centimeter. For a baselined flight plug area of 180 sq cm this yields 790 liters per hour.

Dipirro, Michael J.↗

Effect of surface condition on the formation of solid lubricating films at high temperatures

Solid films were produced on active metal or ceramic surfaces using lubricants (such as tricresyl phosphate) delivered as a vapor at high temperatures, and the lubricity of these deposits under different dynamic wear conditions was investigated. A method is described for chemically activating ceramic surfaces resulting in a surface that could promote the formation of lubricating polymeric derivative of TCP. Experiments were carried out to evaluate the wear characteristics of unlubricated cast iron and of Sialon ceramic at 25 and 280 C, and lubricated with a vapor of TCP at 280 C. It is shown that continuous vapor phase lubrication of chemically treated Sialon reduced its coefficient of friction from 0.7 to less than 0.1.

Hanyaloglu, Bengi↗

Design of RUSL Irradiation Experiment with Free Standing Sample

During FY19, the MIMIC-RUSL TREAT test successfully measured the shift in resonance of a cantilever beam as it underwent a grain restructuring event in the TREAT reactor core. FY20 efforts focused on a new capsule design which would replace the cantilever beam with a free-free beam. The free-free beam configuration eliminates the cantilever boundary condition and enables internal friction measurements. A test capsule was designed which supported the sample beam at the nodal points of the first flexural vibration mode. Initial tests detected the resonance peak but the signal to noise level was not high enough for in-situ measurements. Several detection probes were tested and a significant increase in the signal to noise was achieved. Although adequate signals and clean resonance peaks were measured when the beam was centered, the beam did not self-center when displaced resulting in distorted and inconsistent resonance peaks. It was concluded that the free-free beam approach is likely not suited for in-situ measurements. Measurement of ZGV plate waves is another option for in-situ microstructure monitoring and should be considered for future work.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Using Controlled Impact Experiments to Understand the Effects of Cohesive Blocks on the Cratering Process

When considering large-scale impact events that occur in the gravity-regime, smallscale target heterogeneities (on order of the projectile diameter) are anticipated to have a minimal effect on the cratering process and are therefore not considered in scaling relations [1-3]. Such heterogeneities and other details of the target's strength and structure, however, become increasingly influential as the magnitude of the impact decreases [4]. At the scale of craters forming mostly in regolith on the Moon (< a few meters), for example, target properties such as cohesive strength, density, porosity, and friction have more leverage than gravity to influence the resultant crater dimensions [5]. Further complications beyond just target properties can manifest in many forms, such as subsurface layers [6]; the presence of random, competent blocks [7]; buried lenses of impact melt; and/or pockets of regolith compacted or indurated to varying degrees by previous impacts. Summing the total effect of target properties and any additional heterogeneities for integration into scaling relations is not straightforward, as each individual parameter will have unequal, and so far, unquantified, effects on the final crater. Even when craters are produced under a best-case scenario of controlled laboratory conditions, understanding the entire relevant parameter space can be a formidable task, and deconvolution of all the contributing factors can be a complex undertaking. To begin the process of quantifying such effects, we are conducting an extensive series of impact experiments to build a framework for the interpretation of craters observed on the characteristically complex surfaces throughout the solar system. Here we present the first, and simplest, configuration to be examined in this multi-year experimental campaign: one in which solitary, cohesive blocks are placed in the path of the projectile’s trajectory at different burial depths in granular, sand targets. Among the variables to be investigated in this configuration are the influence of block size, compressive strength, and burial depth.

impact crater↗

Laser-induced fluorescence measurements of argon and xenon ion velocities near the sheath boundary in 3 ion species plasmas

The Bohm sheath criterion is studied with laser-induced fluorescence in three ion species plasmas using two tunable diode lasers. Krypton is added to a low pressure unmagnetized DC hot filament discharge in a mixture of argon and xenon gas confined by surface multi-dipole magnetic fields. The argon and xenon ion velocity distribution functions are measured at the sheath-presheath boundary near a negatively biased boundary plate. The potential structures of the plasma sheath and presheath are measured by an emissive probe. Results are compared with previous experiments with Ar–Xe plasmas, where the two ion species were observed to reach the sheath edge at nearly the same speed. This speed was the ion sound speed of the system, which is consistent with the generalized Bohm criterion. In such two ion species plasmas, instability enhanced collisional friction was demonstrated [Hershkowitz et al., Phys. Plasmas 18(5), 057102 (2011).] to exist which accounted for the observed results. When three ion species are present, it is demonstrated under most circumstances the ions do not fall out of the plasma at their individual Bohm velocities. It is also shown that under most circumstances the ions do not fall out of the plasma at the system sound speed. These observations are also consistent with the presence of the instabilities.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

How earthquakes organize stress

Stress is not uniform in the Earth. Therefore, we must use natural experiments to measure the distribution of stresses and related quantities, rather than single values. For instance, dynamic triggering shows that faults are uniformly distributed over their loading cycles in Southern California. The probability that a fault ruptures across a barrier measures the in situ energy distribution. Fault roughness reflects the distribution of strength. These natural experiments produce observable distributions that are surprisingly consistent and suggest some degree of self-organization in the Earth’s crust. Once established, the functional form of the distributions can be used to track changes in response to earthquakes as well as to distinguish fundamentally different fault systems. Transient fault locking before stress release in laboratory experiments can be interpreted as a consequence of self-organization of fault stress. The robust self-organization of multiple variables in earthquake systems suggests that the most consequential mechanical outcome of earthquakes may be the redistribution of stress and the strain energy associated with it. The low friction on a fault during seismic slip as inferred by temperature measurements of the Tohoku earthquake is consistent with dissipation playing a secondary role to this redistribution process. Through stress redistribution and interaction, subduction zone faults tend to synchronize, perhaps due to their geometric simplicity, while the continental system of Southern California cannot synchronize, perhaps due to the complexity of the fault network. Earthquakes organize stress in the crust and produce a suite of well-defined, consistent distributions.

earthquakes↗

State and Parameter Estimation for Natural Gas Pipeline Networks Using Transient State Data

Here, we formulate two estimation problems for pipeline systems in which measurements of the compressible gas flowing through a network of pipes are affected by time-varying injections, withdrawals, and compression. We consider a state estimation problem that is then extended to a joint state and parameter estimation problem that can be used for data assimilation. In both formulations, the flow dynamics are described on each pipe by space- and time-dependent densities and mass flux which evolve according to a system of coupled partial differential equations, in which momentum dissipation is modeled using the Darcy-Wiesbach friction approximation. These dynamics are first spatially discretized to obtain a system of nonlinear ordinary differential equations on which state and parameter estimation formulations are given as nonlinear least squares problems. A rapid, scalable computational method for performing a nonlinear least squares estimation is developed. Extensive simulations and computational experiments on multiple pipeline test networks demonstrate the effectiveness of the formulations in obtaining state and parameter estimates in the presence of measurement and process noise.

03 NATURAL GAS↗

Surface chemistry of iron sliding in air and nitrogen lubricated with hexadecane and hexadecane containing dibenzyl-dilsulfide

Wear experiments were conducted on iron sliding in hexadecane and hexadecane plus one weight percent dibenzyl dilsulfide (DBDS) in atmospheres of air and nitrogen at room temperature. The wear scars and the wear debris were analyzed by X-ray photoelectron spectroscopy. The presence of air reduced wear but increased friction, while DBDS reduced friction but had little effect on wear except that the wear increased somewhat when DBDS was used in air. Wear scar analysis indicated that oxygen and sulfur competed chemically for the surface, with the oxide predominating. Low wear was associated with a thick oxide layer and low friction with a thin predominantly sulfide layer. Analysis of the wear debris indicated the presence of a sulfate in the high wear case (hexadecane plus DBDS in air), and showed the presence of an organic sulfide in the low wear case (Hexadecane plus DBDS in nitrogen).

Wheeler, D. R.↗